| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
There is no direct device ancestry defined between an ata_device and
its scsi device which prevents the power management code from correctly
ordering suspend and resume operations. Create such ancestry with the
ata device as the parent to ensure that the scsi device (child) is
suspended before the ata device and that resume handles the ata device
before the scsi device.
The parent-child (supplier-consumer) relationship is established between
the ata_port (parent) and the scsi device (child) with the function
device_add_link(). The parent used is not the ata_device as the PM
operations are defined per port and the status of all devices connected
through that port is controlled from the port operations.
The device link is established with the new function
ata_scsi_slave_alloc(), and this function is used to define the
->slave_alloc callback of the scsi host template of all ata drivers.
Fixes: a19a93e4c6a9 ("scsi: core: pm: Rely on the device driver core for async power management")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: John Garry <john.g.garry@oracle.com>
|
|
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
- Seagate IronWolf ST12000VN0008
- Seagate IronWolf ST8000NE0004
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d52a ("libata: change drive ready wait after hard reset to 5s")
Cc: stable@vger.kernel.org
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Fix EL2 Stage-1 MMIO mappings where a random address was used
- Fix SMCCC function number comparison when the SVE hint is set
RISC-V:
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
x86:
- Fixes for TSC_AUX virtualization
- Stop zapping page tables asynchronously, since we don't zap them as
often as before"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: SVM: Do not use user return MSR support for virtualized TSC_AUX
KVM: SVM: Fix TSC_AUX virtualization setup
KVM: SVM: INTERCEPT_RDTSCP is never intercepted anyway
KVM: x86/mmu: Stop zapping invalidated TDP MMU roots asynchronously
KVM: x86/mmu: Do not filter address spaces in for_each_tdp_mmu_root_yield_safe()
KVM: x86/mmu: Open code leaf invalidation from mmu_notifier
KVM: riscv: selftests: Selectively filter-out AIA registers
KVM: riscv: selftests: Fix ISA_EXT register handling in get-reg-list
RISC-V: KVM: Fix riscv_vcpu_get_isa_ext_single() for missing extensions
RISC-V: KVM: Fix KVM_GET_REG_LIST API for ISA_EXT registers
KVM: selftests: Assert that vasprintf() is successful
KVM: arm64: nvhe: Ignore SVE hint in SMCCC function ID
KVM: arm64: Properly return allocated EL2 VA from hyp_alloc_private_va_range()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl
Pull cxl fixes from Dan Williams:
"A collection of regression fixes, bug fixes, and some small cleanups
to the Compute Express Link code.
The regressions arrived in the v6.5 dev cycle and missed the v6.6
merge window due to my personal absences this cycle. The most
important fixes are for scenarios where the CXL subsystem fails to
parse valid region configurations established by platform firmware.
This is important because agreement between OS and BIOS on the CXL
configuration is fundamental to implementing "OS native" error
handling, i.e. address translation and component failure
identification.
Other important fixes are a driver load error when the BIOS lets the
Linux PCI core handle AER events, but not CXL memory errors.
The other fixex might have end user impact, but for now are only known
to trigger in our test/emulation environment.
Summary:
- Fix multiple scenarios where platform firmware defined regions fail
to be assembled by the CXL core.
- Fix a spurious driver-load failure on platforms that enable OS
native AER, but not OS native CXL error handling.
- Fix a regression detecting "poison" commands when "security"
commands are also defined.
- Fix a cxl_test regression with the move to centralize CXL port
register enumeration in the CXL core.
- Miscellaneous small fixes and cleanups"
* tag 'cxl-fixes-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
cxl/acpi: Annotate struct cxl_cxims_data with __counted_by
cxl/port: Fix cxl_test register enumeration regression
cxl/region: Refactor granularity select in cxl_port_setup_targets()
cxl/region: Match auto-discovered region decoders by HPA range
cxl/mbox: Fix CEL logic for poison and security commands
cxl/pci: Replace host_bridge->native_aer with pcie_aer_is_native()
PCI/AER: Export pcie_aer_is_native()
cxl/pci: Fix appropriate checking for _OSC while handling CXL RAS registers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"13 hotfixes, 10 of which pertain to post-6.5 issues. The other three
are cc:stable"
* tag 'mm-hotfixes-stable-2023-09-23-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
proc: nommu: fix empty /proc/<pid>/maps
filemap: add filemap_map_order0_folio() to handle order0 folio
proc: nommu: /proc/<pid>/maps: release mmap read lock
mm: memcontrol: fix GFP_NOFS recursion in memory.high enforcement
pidfd: prevent a kernel-doc warning
argv_split: fix kernel-doc warnings
scatterlist: add missing function params to kernel-doc
selftests/proc: fixup proc-empty-vm test after KSM changes
revert "scripts/gdb/symbols: add specific ko module load command"
selftests: link libasan statically for tests with -fsanitize=address
task_work: add kerneldoc annotation for 'data' argument
mm: page_alloc: fix CMA and HIGHATOMIC landing on the wrong buddy list
sh: mm: re-add lost __ref to ioremap_prot() to fix modpost warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix lockdep, fix a boot failure, fix some build warnings, fix document
links, and some cleanups"
* tag 'loongarch-fixes-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
docs/zh_CN/LoongArch: Update the links of ABI
docs/LoongArch: Update the links of ABI
LoongArch: Don't inline kasan_mem_to_shadow()/kasan_shadow_to_mem()
kasan: Cleanup the __HAVE_ARCH_SHADOW_MAP usage
LoongArch: Set all reserved memblocks on Node#0 at initialization
LoongArch: Remove dead code in relocate_new_kernel
LoongArch: Use _UL() and _ULL()
LoongArch: Fix some build warnings with W=1
LoongArch: Fix lockdep static memory detection
|
|
HEAD
KVM/riscv fixes for 6.6, take #1
- Fix KVM_GET_REG_LIST API for ISA_EXT registers
- Fix reading ISA_EXT register of a missing extension
- Fix ISA_EXT register handling in get-reg-list test
- Fix filtering of AIA registers in get-reg-list test
|
|
Pull xfs fixes from Chandan Babu:
- Fix an integer overflow bug when processing an fsmap call
- Fix crash due to CPU hot remove event racing with filesystem mount
operation
- During read-only mount, XFS does not allow the contents of the log to
be recovered when there are one or more unrecognized rcompat features
in the primary superblock, since the log might have intent items
which the kernel does not know how to process
- During recovery of log intent items, XFS now reserves log space
sufficient for one cycle of a permanent transaction to execute.
Otherwise, this could lead to livelocks due to non-availability of
log space
- On an fs which has an ondisk unlinked inode list, trying to delete a
file or allocating an O_TMPFILE file can cause the fs to the shutdown
if the first inode in the ondisk inode list is not present in the
inode cache. The bug is solved by explicitly loading the first inode
in the ondisk unlinked inode list into the inode cache if it is not
already cached
A similar problem arises when the uncached inode is present in the
middle of the ondisk unlinked inode list. This second bug is
triggered when executing operations like quotacheck and bulkstat. In
this case, XFS now reads in the entire ondisk unlinked inode list
- Enable LARP mode only on recent v5 filesystems
- Fix a out of bounds memory access in scrub
- Fix a performance bug when locating the tail of the log during
mounting a filesystem
* tag 'xfs-6.6-fixes-1' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: use roundup_pow_of_two instead of ffs during xlog_find_tail
xfs: only call xchk_stats_merge after validating scrub inputs
xfs: require a relatively recent V5 filesystem for LARP mode
xfs: make inode unlinked bucket recovery work with quotacheck
xfs: load uncached unlinked inodes into memory on demand
xfs: reserve less log space when recovering log intent items
xfs: fix log recovery when unknown rocompat bits are set
xfs: reload entire unlinked bucket lists
xfs: allow inode inactivation during a ro mount log recovery
xfs: use i_prev_unlinked to distinguish inodes that are not on the unlinked list
xfs: remove CPU hotplug infrastructure
xfs: remove the all-mounts list
xfs: use per-mount cpumask to track nonempty percpu inodegc lists
xfs: fix an agbno overflow in __xfs_getfsmap_datadev
xfs: fix per-cpu CIL structure aggregation racing with dying cpus
xfs: fix select in config XFS_ONLINE_SCRUB_STATS
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Fix a include/linux/atomic/atomic-arch-fallback.h breakage that
generated incorrect code, and fix a lockdep reporting race that may
result in lockups"
* tag 'locking-urgent-2023-09-22' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlock: Do the lockdep annotation before locking in do_write_seqcount_begin_nested()
locking/atomic: scripts: fix fallback ifdeffery
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from netfilter and bpf.
Current release - regressions:
- bpf: adjust size_index according to the value of KMALLOC_MIN_SIZE
- netfilter: fix entries val in rule reset audit log
- eth: stmmac: fix incorrect rxq|txq_stats reference
Previous releases - regressions:
- ipv4: fix null-deref in ipv4_link_failure
- netfilter:
- fix several GC related issues
- fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
- eth: team: fix null-ptr-deref when team device type is changed
- eth: i40e: fix VF VLAN offloading when port VLAN is configured
- eth: ionic: fix 16bit math issue when PAGE_SIZE >= 64KB
Previous releases - always broken:
- core: fix ETH_P_1588 flow dissector
- mptcp: fix several connection hang-up conditions
- bpf:
- avoid deadlock when using queue and stack maps from NMI
- add override check to kprobe multi link attach
- hsr: properly parse HSRv1 supervisor frames.
- eth: igc: fix infinite initialization loop with early XDP redirect
- eth: octeon_ep: fix tx dma unmap len values in SG
- eth: hns3: fix GRE checksum offload issue"
* tag 'net-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
sfc: handle error pointers returned by rhashtable_lookup_get_insert_fast()
igc: Expose tx-usecs coalesce setting to user
octeontx2-pf: Do xdp_do_flush() after redirects.
bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
net: ena: Flush XDP packets on error.
net/handshake: Fix memory leak in __sock_create() and sock_alloc_file()
net: hinic: Fix warning-hinic_set_vlan_fliter() warn: variable dereferenced before check 'hwdev'
netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
netfilter: nf_tables: fix memleak when more than 255 elements expired
netfilter: nf_tables: disable toggling dormant table state more than once
vxlan: Add missing entries to vxlan_get_size()
net: rds: Fix possible NULL-pointer dereference
team: fix null-ptr-deref when team device type is changed
net: bridge: use DEV_STATS_INC()
net: hns3: add 5ms delay before clear firmware reset irq source
net: hns3: fix fail to delete tc flower rules during reset issue
net: hns3: only enable unicast promisc when mac table full
net: hns3: fix GRE checksum offload issue
net: hns3: add cmdq check for vf periodic service task
net: stmmac: fix incorrect rxq|txq_stats reference
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs
Pull finegrained timestamp reverts from Christian Brauner:
"Earlier this week we sent a few minor fixes for the multi-grained
timestamp work in [1]. While we were polishing those up after Linus
realized that there might be a nicer way to fix them we received a
regression report in [2] that fine grained timestamps break gnulib
tests and thus possibly other tools.
The kernel will elide fine-grain timestamp updates when no one is
actively querying for them to avoid performance impacts. So a sequence
like write(f1) stat(f2) write(f2) stat(f2) write(f1) stat(f1) may
result in timestamp f1 to be older than the final f2 timestamp even
though f1 was last written too but the second write didn't update the
timestamp.
Such plotholes can lead to subtle bugs when programs compare
timestamps. For example, the nap() function in [2] will estimate that
it needs to wait one ns on a fine-grain timestamp enabled filesytem
between subsequent calls to observe a timestamp change. But in general
we don't update timestamps with more than one jiffie if we think that
no one is actively querying for fine-grain timestamps to avoid
performance impacts.
While discussing various fixes the decision was to go back to the
drawing board and ultimately to explore a solution that involves only
exposing such fine-grained timestamps to nfs internally and never to
userspace.
As there are multiple solutions discussed the honest thing to do here
is not to fix this up or disable it but to cleanly revert. The general
infrastructure will probably come back but there is no reason to keep
this code in mainline.
The general changes to timestamp handling are valid and a good cleanup
that will stay. The revert is fully bisectable"
Link: https://lore.kernel.org/all/20230918-hirte-neuzugang-4c2324e7bae3@brauner [1]
Link: https://lore.kernel.org/all/bf0524debb976627693e12ad23690094e4514303.camel@linuxfromscratch.org [2]
* tag 'v6.6-rc3.vfs.ctime.revert' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
Revert "fs: add infrastructure for multigrain timestamps"
Revert "btrfs: convert to multigrain timestamps"
Revert "ext4: switch to multigrain timestamps"
Revert "xfs: switch to multigrain timestamps"
Revert "tmpfs: add support for multigrain timestamps"
|
|
do_write_seqcount_begin_nested()
It was brought up by Tetsuo that the following sequence:
write_seqlock_irqsave()
printk_deferred_enter()
could lead to a deadlock if the lockdep annotation within
write_seqlock_irqsave() triggers.
The problem is that the sequence counter is incremented before the lockdep
annotation is performed. The lockdep splat would then attempt to invoke
printk() but the reader side, of the same seqcount, could have a
tty_port::lock acquired waiting for the sequence number to become even again.
The other lockdep annotations come before the actual locking because "we
want to see the locking error before it happens". There is no reason why
seqcount should be different here.
Do the lockdep annotation first then perform the locking operation (the
sequence increment).
Fixes: 1ca7d67cf5d5a ("seqcount: Add lockdep functionality to seqcount/seqlock structures")
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230920104627._DTHgPyA@linutronix.de
Closes: https://lore.kernel.org/20230621130641.-5iueY1I@linutronix.de
|
|
This reverts commit ffb6cf19e06334062744b7e3493f71e500964f8e.
Users reported regressions due to enabling multi-grained timestamps
unconditionally. As no clear consensus on a solution has come up and the
discussion has gone back to the drawing board revert the infrastructure
changes for. If it isn't code that's here to stay, make it go away.
Message-ID: <20230920-keine-eile-c9755b5825db@brauner>
Acked-by: Jan Kara <jack@suse.cz>
Acked-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Christian Brauner <brauner@kernel.org>
|
|
Since commit:
9257959a6e5b4fca ("locking/atomic: scripts: restructure fallback ifdeffery")
The ordering fallbacks for atomic*_read_acquire() and
atomic*_set_release() erroneously fall back to the implictly relaxed
atomic*_read() and atomic*_set() variants respectively, without any
additional barriers. This loses the ACQUIRE and RELEASE ordering
semantics, which can result in a wide variety of problems, even on
strongly-ordered architectures where the implementation of
atomic*_read() and/or atomic*_set() allows the compiler to reorder those
relative to other accesses.
In practice this has been observed to break bit spinlocks on arm64,
resulting in dentry cache corruption.
The fallback logic was intended to allow ACQUIRE/RELEASE/RELAXED ops to
be defined in terms of FULL ops, but where an op had RELAXED ordering by
default, this unintentionally permitted the ACQUIRE/RELEASE ops to be
defined in terms of the implicitly RELAXED default.
This patch corrects the logic to avoid falling back to implicitly
RELAXED ops, resulting in the same behaviour as prior to commit
9257959a6e5b4fca.
I've verified the resulting assembly on arm64 by generating outlined
wrappers of the atomics. Prior to this patch the compiler generates
sequences using relaxed load (LDR) and store (STR) instructions, e.g.
| <outlined_atomic64_read_acquire>:
| ldr x0, [x0]
| ret
|
| <outlined_atomic64_set_release>:
| str x1, [x0]
| ret
With this patch applied the compiler generates sequences using the
intended load-acquire (LDAR) and store-release (STLR) instructions, e.g.
| <outlined_atomic64_read_acquire>:
| ldar x0, [x0]
| ret
|
| <outlined_atomic64_set_release>:
| stlr x1, [x0]
| ret
To make sure that there were no other victims of the ifdeffery rewrite,
I generated outlined copies of all of the {atomic,atomic64,atomic_long}
atomic operations before and after commit 9257959a6e5b4fca. A diff of
the generated assembly on arm64 shows that only the read_acquire() and
set_release() operations were changed, and only lost their intended
ordering:
| [mark@lakrids:~/src/linux]% diff -u \
| <(aarch64-linux-gnu-objdump -d before-9257959a6e5b4fca.o)
| <(aarch64-linux-gnu-objdump -d after-9257959a6e5b4fca.o)
| --- /proc/self/fd/11 2023-09-19 16:51:51.114779415 +0100
| +++ /proc/self/fd/16 2023-09-19 16:51:51.114779415 +0100
| @@ -1,5 +1,5 @@
|
| -before-9257959a6e5b4fca.o: file format elf64-littleaarch64
| +after-9257959a6e5b4fca.o: file format elf64-littleaarch64
|
|
| Disassembly of section .text:
| @@ -9,7 +9,7 @@
| 4: d65f03c0 ret
|
| 0000000000000008 <outlined_atomic_read_acquire>:
| - 8: 88dffc00 ldar w0, [x0]
| + 8: b9400000 ldr w0, [x0]
| c: d65f03c0 ret
|
| 0000000000000010 <outlined_atomic_set>:
| @@ -17,7 +17,7 @@
| 14: d65f03c0 ret
|
| 0000000000000018 <outlined_atomic_set_release>:
| - 18: 889ffc01 stlr w1, [x0]
| + 18: b9000001 str w1, [x0]
| 1c: d65f03c0 ret
|
| 0000000000000020 <outlined_atomic_add>:
| @@ -1230,7 +1230,7 @@
| 1070: d65f03c0 ret
|
| 0000000000001074 <outlined_atomic64_read_acquire>:
| - 1074: c8dffc00 ldar x0, [x0]
| + 1074: f9400000 ldr x0, [x0]
| 1078: d65f03c0 ret
|
| 000000000000107c <outlined_atomic64_set>:
| @@ -1238,7 +1238,7 @@
| 1080: d65f03c0 ret
|
| 0000000000001084 <outlined_atomic64_set_release>:
| - 1084: c89ffc01 stlr x1, [x0]
| + 1084: f9000001 str x1, [x0]
| 1088: d65f03c0 ret
|
| 000000000000108c <outlined_atomic64_add>:
| @@ -2427,7 +2427,7 @@
| 207c: d65f03c0 ret
|
| 0000000000002080 <outlined_atomic_long_read_acquire>:
| - 2080: c8dffc00 ldar x0, [x0]
| + 2080: f9400000 ldr x0, [x0]
| 2084: d65f03c0 ret
|
| 0000000000002088 <outlined_atomic_long_set>:
| @@ -2435,7 +2435,7 @@
| 208c: d65f03c0 ret
|
| 0000000000002090 <outlined_atomic_long_set_release>:
| - 2090: c89ffc01 stlr x1, [x0]
| + 2090: f9000001 str x1, [x0]
| 2094: d65f03c0 ret
|
| 0000000000002098 <outlined_atomic_long_add>:
I've build tested this with a variety of configs for alpha, arm, arm64,
csky, i386, m68k, microblaze, mips, nios2, openrisc, powerpc, riscv,
s390, sh, sparc, x86_64, and xtensa, for which I've seen no issues. I
was unable to build test for ia64 and parisc due to existing build
breakage in v6.6-rc2.
Fixes: 9257959a6e5b4fca ("locking/atomic: scripts: restructure fallback ifdeffery")
Reported-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Darrick J. Wong <djwong@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Baokun Li <libaokun1@huawei.com>
Link: https://lkml.kernel.org/r/20230919171430.2697727-1-mark.rutland@arm.com
|
|
As Linus suggested, __HAVE_ARCH_XYZ is "stupid" and "having historical
uses of it doesn't make it good". So migrate __HAVE_ARCH_SHADOW_MAP to
separate macros named after the respective functions.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reviewed-by: WANG Xuerui <git@xen0n.name>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Breno and Josef report a deadlock scenario from cgroup reclaim
re-entering the filesystem:
[ 361.546690] ======================================================
[ 361.559210] WARNING: possible circular locking dependency detected
[ 361.571703] 6.5.0-0_fbk700_debug_rc0_kbuilder_13159_gbf787a128001 #1 Tainted: G S E
[ 361.589704] ------------------------------------------------------
[ 361.602277] find/9315 is trying to acquire lock:
[ 361.611625] ffff88837ba140c0 (&delayed_node->mutex){+.+.}-{4:4}, at: __btrfs_release_delayed_node+0x68/0x4f0
[ 361.631437]
[ 361.631437] but task is already holding lock:
[ 361.643243] ffff8881765b8678 (btrfs-tree-01){++++}-{4:4}, at: btrfs_tree_read_lock+0x1e/0x40
[ 362.904457] mutex_lock_nested+0x1c/0x30
[ 362.912414] __btrfs_release_delayed_node+0x68/0x4f0
[ 362.922460] btrfs_evict_inode+0x301/0x770
[ 362.982726] evict+0x17c/0x380
[ 362.988944] prune_icache_sb+0x100/0x1d0
[ 363.005559] super_cache_scan+0x1f8/0x260
[ 363.013695] do_shrink_slab+0x2a2/0x540
[ 363.021489] shrink_slab_memcg+0x237/0x3d0
[ 363.050606] shrink_slab+0xa7/0x240
[ 363.083382] shrink_node_memcgs+0x262/0x3b0
[ 363.091870] shrink_node+0x1a4/0x720
[ 363.099150] shrink_zones+0x1f6/0x5d0
[ 363.148798] do_try_to_free_pages+0x19b/0x5e0
[ 363.157633] try_to_free_mem_cgroup_pages+0x266/0x370
[ 363.190575] reclaim_high+0x16f/0x1f0
[ 363.208409] mem_cgroup_handle_over_high+0x10b/0x270
[ 363.246678] try_charge_memcg+0xaf2/0xc70
[ 363.304151] charge_memcg+0xf0/0x350
[ 363.320070] __mem_cgroup_charge+0x28/0x40
[ 363.328371] __filemap_add_folio+0x870/0xd50
[ 363.371303] filemap_add_folio+0xdd/0x310
[ 363.399696] __filemap_get_folio+0x2fc/0x7d0
[ 363.419086] pagecache_get_page+0xe/0x30
[ 363.427048] alloc_extent_buffer+0x1cd/0x6a0
[ 363.435704] read_tree_block+0x43/0xc0
[ 363.443316] read_block_for_search+0x361/0x510
[ 363.466690] btrfs_search_slot+0xc8c/0x1520
This is caused by the mem_cgroup_handle_over_high() not respecting the
gfp_mask of the allocation context. We used to only call this function on
resume to userspace, where no locks were held. But c9afe31ec443 ("memcg:
synchronously enforce memory.high for large overcharges") added a call
from the allocation context without considering the gfp.
Link: https://lkml.kernel.org/r/20230914152139.100822-1-hannes@cmpxchg.org
Fixes: c9afe31ec443 ("memcg: synchronously enforce memory.high for large overcharges")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Breno Leitao <leitao@debian.org>
Reported-by: Josef Bacik <josef@toxicpanda.com>
Acked-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: <stable@vger.kernel.org> [5.17+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Get a null-ptr-deref bug as follows with reproducer [1].
BUG: kernel NULL pointer dereference, address: 0000000000000228
...
RIP: 0010:vlan_dev_hard_header+0x35/0x140 [8021q]
...
Call Trace:
<TASK>
? __die+0x24/0x70
? page_fault_oops+0x82/0x150
? exc_page_fault+0x69/0x150
? asm_exc_page_fault+0x26/0x30
? vlan_dev_hard_header+0x35/0x140 [8021q]
? vlan_dev_hard_header+0x8e/0x140 [8021q]
neigh_connected_output+0xb2/0x100
ip6_finish_output2+0x1cb/0x520
? nf_hook_slow+0x43/0xc0
? ip6_mtu+0x46/0x80
ip6_finish_output+0x2a/0xb0
mld_sendpack+0x18f/0x250
mld_ifc_work+0x39/0x160
process_one_work+0x1e6/0x3f0
worker_thread+0x4d/0x2f0
? __pfx_worker_thread+0x10/0x10
kthread+0xe5/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x34/0x50
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1b/0x30
[1]
$ teamd -t team0 -d -c '{"runner": {"name": "loadbalance"}}'
$ ip link add name t-dummy type dummy
$ ip link add link t-dummy name t-dummy.100 type vlan id 100
$ ip link add name t-nlmon type nlmon
$ ip link set t-nlmon master team0
$ ip link set t-nlmon nomaster
$ ip link set t-dummy up
$ ip link set team0 up
$ ip link set t-dummy.100 down
$ ip link set t-dummy.100 master team0
When enslave a vlan device to team device and team device type is changed
from non-ether to ether, header_ops of team device is changed to
vlan_header_ops. That is incorrect and will trigger null-ptr-deref
for vlan->real_dev in vlan_dev_hard_header() because team device is not
a vlan device.
Cache eth_header_ops in team_setup(), then assign cached header_ops to
header_ops of team net device when its type is changed from non-ether
to ether to fix the bug.
Fixes: 1d76efe1577b ("team: add support for non-ethernet devices")
Suggested-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230918123011.1884401-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Pull NFS client fixes from Anna Schumaker:
"Various O_DIRECT related fixes from Trond:
- Error handling
- Locking issues
- Use the correct commit info for joining page groups
- Fixes for rescheduling IO
Sunrpc bad verifier fixes:
- Report EINVAL errors from connect()
- Revalidate creds that the server has rejected
- Revert "SUNRPC: Fail faster on bad verifier"
Misc:
- Fix pNFS session trunking when MDS=DS
- Fix zero-value filehandles for post-open getattr operations
- Fix compiler warning about tautological comparisons
- Revert 'SUNRPC: clean up integer overflow check' before Trond's fix"
* tag 'nfs-for-6.6-2' of git://git.linux-nfs.org/projects/anna/linux-nfs:
SUNRPC: Silence compiler complaints about tautological comparisons
Revert "SUNRPC: clean up integer overflow check"
NFSv4.1: fix zero value filehandle in post open getattr
NFSv4.1: fix pnfs MDS=DS session trunking
Revert "SUNRPC: Fail faster on bad verifier"
SUNRPC: Mark the cred for revalidation if the server rejects it
NFS/pNFS: Report EINVAL errors from connect() to the server
NFS: More fixes for nfs_direct_write_reschedule_io()
NFS: Use the correct commit info in nfs_join_page_group()
NFS: More O_DIRECT accounting fixes for error paths
NFS: Fix O_DIRECT locking issues
NFS: Fix error handling for O_DIRECT write scheduling
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- Fix an UV boot crash
- Skip spurious ENDBR generation on _THIS_IP_
- Fix ENDBR use in putuser() asm methods
- Fix corner case boot crashes on 5-level paging
- and fix a false positive WARNING on LTO kernels"
* tag 'x86-urgent-2023-09-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/purgatory: Remove LTO flags
x86/boot/compressed: Reserve more memory for page tables
x86/ibt: Avoid duplicate ENDBR in __put_user_nocheck*()
x86/ibt: Suppress spurious ENDBR
x86/platform/uv: Use alternate source for socket to node data
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Regression and bug fixes for ext4"
* tag 'ext4_for_linus-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix rec_len verify error
ext4: do not let fstrim block system suspend
ext4: move setting of trimmed bit into ext4_try_to_trim_range()
jbd2: Fix memory leak in journal_init_common()
jbd2: Remove page size assumptions
buffer: Make bh_offset() work for compound pages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"16 small(ish) fixes all in drivers.
The major fixes are in pm8001 (fixes MSI-X issue going back to its
origin), the qla2xxx endianness fix, which fixes a bug on big endian
and the lpfc ones which can cause an oops on module removal without
them"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Prevent use-after-free during rmmod with mapped NVMe rports
scsi: lpfc: Early return after marking final NLP_DROPPED flag in dev_loss_tmo
scsi: lpfc: Fix the NULL vs IS_ERR() bug for debugfs_create_file()
scsi: target: core: Fix target_cmd_counter leak
scsi: pm8001: Setup IRQs on resume
scsi: pm80xx: Avoid leaking tags when processing OPC_INB_SET_CONTROLLER_CONFIG command
scsi: pm80xx: Use phy-specific SAS address when sending PHY_START command
scsi: ufs: core: Poll HCS.UCRDY before issuing a UIC command
scsi: ufs: core: Move __ufshcd_send_uic_cmd() outside host_lock
scsi: qedf: Add synchronization between I/O completions and abort
scsi: target: Replace strlcpy() with strscpy()
scsi: qla2xxx: Fix NULL vs IS_ERR() bug for debugfs_create_dir()
scsi: qla2xxx: Use raw_smp_processor_id() instead of smp_processor_id()
scsi: qla2xxx: Correct endianness for rqstlen and rsplen
scsi: ppa: Fix accidentally reversed conditions for 16-bit and 32-bit EPP
scsi: megaraid_sas: Fix deadlock on firmware crashdump
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata
Pull ata fixes from Damien Le Moal:
- Fix link power management transitions to disallow unsupported states
(Niklas)
- A small string handling fix for the sata_mv driver (Christophe)
- Clear port pending interrupts before reset, as per AHCI
specifications (Szuying).
Followup fixes for this one are to not clear ATA_PFLAG_EH_PENDING in
ata_eh_reset() to allow EH to continue on with other actions recorded
with error interrupts triggered before EH completes. And an
additional fix to avoid thawing a port twice in EH (Niklas)
- Small code style fixes in the pata_parport driver to silence the
build bot as it keeps complaining about bad indentation (me)
- A fix for the recent CDL code to avoid fetching sense data for
successful commands when not necessary for correct operation (Niklas)
* tag 'ata-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: libata-core: fetch sense data for successful commands iff CDL enabled
ata: libata-eh: do not thaw the port twice in ata_eh_reset()
ata: libata-eh: do not clear ATA_PFLAG_EH_PENDING in ata_eh_reset()
ata: pata_parport: Fix code style issues
ata: libahci: clear pending interrupt status
ata: sata_mv: Fix incorrect string length computation in mv_dump_mem()
ata: libata: disallow dev-initiated LPM transitions to unsupported states
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"The main thing is the removal of 'probe_new' because all i2c client
drivers are converted now. Thanks Uwe, this marks the end of a long
conversion process.
Other than that, we have a few Kconfig updates and driver bugfixes"
* tag 'i2c-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: cadence: Fix the kernel-doc warnings
i2c: aspeed: Reset the i2c controller when timeout occurs
i2c: I2C_MLXCPLD on ARM64 should depend on ACPI
i2c: Make I2C_ATR invisible
i2c: Drop legacy callback .probe_new()
w1: ds2482: Switch back to use struct i2c_driver's .probe()
|
|
Alexei Starovoitov says:
====================
The following pull-request contains BPF updates for your *net* tree.
We've added 21 non-merge commits during the last 8 day(s) which contain
a total of 21 files changed, 450 insertions(+), 36 deletions(-).
The main changes are:
1) Adjust bpf_mem_alloc buckets to match ksize(), from Hou Tao.
2) Check whether override is allowed in kprobe mult, from Jiri Olsa.
3) Fix btf_id symbol generation with ld.lld, from Jiri and Nick.
4) Fix potential deadlock when using queue and stack maps from NMI, from Toke Høiland-Jørgensen.
Please consider pulling these changes from:
git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf.git
Thanks a lot!
Also thanks to reporters, reviewers and testers of commits in this pull-request:
Alan Maguire, Biju Das, Björn Töpel, Dan Carpenter, Daniel Borkmann,
Eduard Zingerman, Hsin-Wei Hung, Marcus Seyfarth, Nathan Chancellor,
Satya Durga Srinivasu Prabhala, Song Liu, Stephen Rothwell
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"These fix a thermal core breakage introduced by one of the recent
changes, amend those changes by adding 'const' to a new callback
argument and fix two memory leaks.
Specifics:
- Unbreak disabled trip point check in handle_thermal_trip() that may
cause it to skip enabled trip points (Rafael Wysocki)
- Add missing of_node_put() to of_find_trip_id() and
thermal_of_for_each_cooling_maps() that each break out of a
for_each_child_of_node() loop without dropping the reference to the
child object (Julia Lawall)
- Constify the recently added trip argument of the .get_trend()
thermal zone callback (Rafael Wysocki)"
* tag 'thermal-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Fix disabled trip point check in handle_thermal_trip()
thermal: Constify the trip argument of the .get_trend() zone callback
thermal/of: add missing of_node_put()
|
|
On 64-bit systems, the compiler will complain that the comparison
between SIZE_MAX and the 32-bit unsigned int 'len' is unnecessary.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
This reverts commit e87cf8a28e7592bd19064e8181324ae26bc02932.
This commit was added to silence a tautological comparison warning, but
removing the 'len' value check before calling xdr_inline_decode() is
really not what we want.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Marcus and Satya reported an issue where BTF_ID macro generates same
symbol in separate objects and that breaks final vmlinux link.
ld.lld: error: ld-temp.o <inline asm>:14577:1: symbol
'__BTF_ID__struct__cgroup__624' is already defined
This can be triggered under specific configs when __COUNTER__ happens to
be the same for the same symbol in two different translation units,
which is already quite unlikely to happen.
Add __LINE__ number suffix to make BTF_ID symbol more unique, which is
not a complete fix, but it would help for now and meanwhile we can work
on better solution as suggested by Andrii.
Cc: stable@vger.kernel.org
Reported-by: Satya Durga Srinivasu Prabhala <quic_satyap@quicinc.com>
Reported-by: Marcus Seyfarth <m.seyfarth@gmail.com>
Closes: https://github.com/ClangBuiltLinux/linux/issues/1913
Debugged-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/bpf/CAEf4Bzb5KQ2_LmhN769ifMeSJaWfebccUasQOfQKaOd0nQ51tw@mail.gmail.com/
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20230915-bpf_collision-v3-1-263fc519c21f@google.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Pull in staged fixes for 6.6.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture fixes from Helge Deller:
- fix reference to exported symbols for parisc64 [Masahiro Yamada]
- Block-TLB (BTLB) support on 32-bit CPUs
- sparse and build-warning fixes
* tag 'parisc-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
linux/export: fix reference to exported functions for parisc64
parisc: BTLB: Initialize BTLB tables at CPU startup
parisc: firmware: Simplify calling non-PA20 functions
parisc: BTLB: _edata symbol has to be page aligned for BTLB support
parisc: BTLB: Add BTLB insert and purge firmware function wrappers
parisc: BTLB: Clear possibly existing BTLB entries
parisc: Prepare for Block-TLB support on 32-bit kernel
parisc: shmparam.h: Document aliasing requirements of PA-RISC
parisc: irq: Make irq_stack_union static to avoid sparse warning
parisc: drivers: Fix sparse warning
parisc: iosapic.c: Fix sparse warnings
parisc: ccio-dma: Fix sparse warnings
parisc: sba-iommu: Fix sparse warnigs
parisc: sba: Fix compile warning wrt list of SBA devices
parisc: sba_iommu: Fix build warning if procfs if disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Add missing LOCKDOWN checks for eventfs callers
When LOCKDOWN is active for tracing, it causes inconsistent state
when some functions succeed and others fail.
- Use dput() to free the top level eventfs descriptor
There was a race between accesses and freeing it.
- Fix a long standing bug that eventfs exposed due to changing timings
by dynamically creating files. That is, If a event file is opened for
an instance, there's nothing preventing the instance from being
removed which will make accessing the files cause use-after-free
bugs.
- Fix a ring buffer race that happens when iterating over the ring
buffer while writers are active. Check to make sure not to read the
event meta data if it's beyond the end of the ring buffer sub buffer.
- Fix the print trigger that disappeared because the test to create it
was looking for the event dir field being filled, but now it has the
"ef" field filled for the eventfs structure.
- Remove the unused "dir" field from the event structure.
- Fix the order of the trace_dynamic_info as it had it backwards for
the offset and len fields for which one was for which endianess.
- Fix NULL pointer dereference with eventfs_remove_rec()
If an allocation fails in one of the eventfs_add_*() functions, the
caller of it in event_subsystem_dir() or event_create_dir() assigns
the result to the structure. But it's assigning the ERR_PTR and not
NULL. This was passed to eventfs_remove_rec() which expects either a
good pointer or a NULL, not ERR_PTR. The fix is to not assign the
ERR_PTR to the structure, but to keep it NULL on error.
- Fix list_for_each_rcu() to use list_for_each_srcu() in
dcache_dir_open_wrapper(). One iteration of the code used RCU but
because it had to call sleepable code, it had to be changed to use
SRCU, but one of the iterations was missed.
- Fix synthetic event print function to use "as_u64" instead of passing
in a pointer to the union. To fix big/little endian issues, the u64
that represented several types was turned into a union to define the
types properly.
* tag 'trace-v6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
eventfs: Fix the NULL pointer dereference bug in eventfs_remove_rec()
tracefs/eventfs: Use list_for_each_srcu() in dcache_dir_open_wrapper()
tracing/synthetic: Print out u64 values properly
tracing/synthetic: Fix order of struct trace_dynamic_info
selftests/ftrace: Fix dependencies for some of the synthetic event tests
tracing: Remove unused trace_event_file dir field
tracing: Use the new eventfs descriptor for print trigger
ring-buffer: Do not attempt to read past "commit"
tracefs/eventfs: Free top level files on removal
ring-buffer: Avoid softlockup in ring_buffer_resize()
tracing: Have event inject files inc the trace array ref count
tracing: Have option files inc the trace array ref count
tracing: Have current_trace inc the trace array ref count
tracing: Have tracing_max_latency inc the trace array ref count
tracing: Increase trace array ref count on enable and filter files
tracefs/eventfs: Use dput to free the toplevel events directory
tracefs/eventfs: Add missing lockdown checks
tracefs: Add missing lockdown check to tracefs_create_dir()
|
|
Currently, when GETDEVICEINFO returns multiple locations where each
is a different IP but the server's identity is same as MDS, then
nfs4_set_ds_client() finds the existing nfs_client structure which
has the MDS's max_connect value (and if it's 1), then the 1st IP
on the DS's list will get dropped due to MDS trunking rules. Other
IPs would be added as they fall under the pnfs trunking rules.
For the list of IPs the 1st goes thru calling nfs4_set_ds_client()
which will eventually call nfs4_add_trunk() and call into
rpc_clnt_test_and_add_xprt() which has the check for MDS trunking.
The other IPs (after the 1st one), would call rpc_clnt_add_xprt()
which doesn't go thru that check.
nfs4_add_trunk() is called when MDS trunking is happening and it
needs to enforce the usage of max_connect mount option of the
1st mount. However, this shouldn't be applied to pnfs flow.
Instead, this patch proposed to treat MDS=DS as DS trunking and
make sure that MDS's max_connect limit does not apply to the
1st IP returned in the GETDEVICEINFO list. It does so by
marking the newly created client with a new flag NFS_CS_PNFS
which then used to pass max_connect value to use into the
rpc_clnt_test_and_add_xprt() instead of the existing rpc
client's max_connect value set by the MDS connection.
For example, mount was done without max_connect value set
so MDS's rpc client has cl_max_connect=1. Upon calling into
rpc_clnt_test_and_add_xprt() and using rpc client's value,
the caller passes in max_connect value which is previously
been set in the pnfs path (as a part of handling
GETDEVICEINFO list of IPs) in nfs4_set_ds_client().
However, when NFS_CS_PNFS flag is not set and we know we
are doing MDS trunking, comparing a new IP of the same
server, we then set the max_connect value to the
existing MDS's value and pass that into
rpc_clnt_test_and_add_xprt().
Fixes: dc48e0abee24 ("SUNRPC enforce creation of no more than max_connect xprts")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Ensure that nfs_clear_request_commit() updates the correct counters when
it removes them from the commit list.
Fixes: ed5d588fe47f ("NFS: Try to join page groups before an O_DIRECT retransmission")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
|
|
Now that all drivers are converted to the (new) .probe() callback, the
temporary .probe_new() can go away. \o/
Link: https://lore.kernel.org/linux-i2c/20230626094548.559542-1-u.kleine-koenig@pengutronix.de
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
It was reported that under certain circumstances GCC emits ENDBR
instructions for _THIS_IP_ usage. Specifically, when it appears at the
start of a basic block -- but not elsewhere.
Since _THIS_IP_ is never used for control flow, these ENDBR
instructions are completely superfluous. Override the _THIS_IP_
definition for x86_64 to avoid this.
Less ENDBR instructions is better.
Fixes: 156ff4a544ae ("x86/ibt: Base IBT bits")
Reported-by: David Kaplan <David.Kaplan@amd.com>
Reviewed-by: Andrew Cooper <andrew.cooper3@citrix.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20230802110323.016197440@infradead.org
|
|
John David Anglin reported parisc has been broken since commit
ddb5cdbafaaa ("kbuild: generate KSYMTAB entries by modpost").
Like ia64, parisc64 uses a function descriptor. The function
references must be prefixed with P%.
Also, symbols prefixed $$ from the library have the symbol type
STT_LOPROC instead of STT_FUNC. They should be handled as functions
too.
Fixes: ddb5cdbafaaa ("kbuild: generate KSYMTAB entries by modpost")
Reported-by: John David Anglin <dave.anglin@bell.net>
Tested-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Helge Deller <deller@gmx.de>
Closes: https://lore.kernel.org/linux-parisc/1901598a-e11d-f7dd-a5d9-9a69d06e6b6e@bell.net/T/#u
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
When SVE is enabled, the host may set bit 16 in SMCCC function IDs, a
hint that indicates an unused SVE state. At the moment NVHE doesn't
account for this bit when inspecting the function ID, and rejects most
calls. Clear the hint bit before comparing function IDs.
About version compatibility: the host's PSCI driver initially probes the
firmware for a SMCCC version number. If the firmware implements a
protocol recent enough (1.3), subsequent SMCCC calls have the hint bit
set. Since the hint bit was reserved in earlier versions of the
protocol, clearing it is fine regardless of the version in use.
When a new hint is added to the protocol in the future, it will be added
to ARM_SMCCC_CALL_HINTS and NVHE will handle it straight away. This
patch only clears known hints and leaves reserved bits as is, because
future SMCCC versions could use reserved bits as modifiers for the
function ID, rather than hints.
Fixes: cfa7ff959a78 ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint")
Reported-by: Ben Horgan <ben.horgan@arm.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20230911145254.934414-4-jean-philippe@linaro.org
|
|
Export and move the declaration of pcie_aer_is_native() to a common header
file to be reused by cxl/pci module.
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Robert Richter <rrichter@amd.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20230823234305.27333-3-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
To make handling BIG and LITTLE endian better the offset/len of dynamic
fields of the synthetic events was changed into a structure of:
struct trace_dynamic_info {
#ifdef CONFIG_CPU_BIG_ENDIAN
u16 offset;
u16 len;
#else
u16 len;
u16 offset;
#endif
};
to replace the manual changes of:
data_offset = offset & 0xffff;
data_offest = len << 16;
But if you look closely, the above is:
<len> << 16 | offset
Which in little endian would be in memory:
offset_lo offset_hi len_lo len_hi
and in big endian:
len_hi len_lo offset_hi offset_lo
Which if broken into a structure would be:
struct trace_dynamic_info {
#ifdef CONFIG_CPU_BIG_ENDIAN
u16 len;
u16 offset;
#else
u16 offset;
u16 len;
#endif
};
Which is the opposite of what was defined.
Fix this and just to be safe also add "__packed".
Link: https://lore.kernel.org/all/20230908154417.5172e343@gandalf.local.home/
Link: https://lore.kernel.org/linux-trace-kernel/20230908163929.2c25f3dc@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Tested-by: Sven Schnelle <svens@linux.ibm.com>
Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
Fixes: ddeea494a16f3 ("tracing/synthetic: Use union instead of casts")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
There are no users of the cpu hotplug hooks in xfs now, so remove it.
This reverts f1653c2e2831e ("xfs: introduce CPU hotplug
infrastructure").
Signed-off-by: Darrick J. Wong <djwong@kernel.org>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
|
|
Add 'const' to the definition of the 'trip' argument of the
.get_trend() thermal zone callback to indicate that the trip point
passed to it should not be modified by it and adjust the
callback functions implementing it, thermal_get_trend() in the
ACPI thermal driver and __ti_thermal_get_trend(), accordingly.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
|
|
In AHCI 1.3.1, the register description for CAP.SSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Slumber state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Slumber requests."
In AHCI 1.3.1, the register description for CAP.PSC:
"When cleared to ‘0’, software must not allow the HBA to initiate
transitions to the Partial state via agressive link power management nor
the PxCMD.ICC field in each port, and the PxSCTL.IPM field in each port
must be programmed to disallow device initiated Partial requests."
Ensure that we always set the corresponding bits in PxSCTL.IPM, such that
a device is not allowed to initiate transitions to power states which are
unsupported by the HBA.
DevSleep is always initiated by the HBA, however, for completeness, set the
corresponding bit in PxSCTL.IPM such that agressive link power management
cannot transition to DevSleep if DevSleep is not supported.
sata_link_scr_lpm() is used by libahci, ata_piix and libata-pmp.
However, only libahci has the ability to read the CAP/CAP2 register to see
if these features are supported. Therefore, in order to not introduce any
regressions on ata_piix or libata-pmp, create flags that indicate that the
respective feature is NOT supported. This way, the behavior for ata_piix
and libata-pmp should remain unchanged.
This change is based on a patch originally submitted by Runa Guo-oc.
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Fixes: 1152b2617a6e ("libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <dlemoal@kernel.org>
|
|
git://git.samba.org/sfrench/cifs-2.6
Pull smb client fixes from Steve French:
- six smb3 client fixes including ones to allow controlling smb3
directory caching timeout and limits, and one debugging improvement
- one fix for nls Kconfig (don't need to expose NLS_UCS2_UTILS option)
- one minor spnego registry update
* tag '6.6-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
spnego: add missing OID to oid registry
smb3: fix minor typo in SMB2_GLOBAL_CAP_LARGE_MTU
cifs: update internal module version number for cifs.ko
smb3: allow controlling maximum number of cached directories
smb3: add trace point for queryfs (statfs)
nls: Hide new NLS_UCS2_UTILS
smb3: allow controlling length of time directory entries are cached with dir leases
smb: propagate error code of extract_sharename()
|
|
Pull more SCSI updates from James Bottomley:
"Mostly small stragglers that missed the initial merge.
Driver updates are qla2xxx and smartpqi (mp3sas has a high diffstat
due to the volatile qualifier removal, fnic due to unused function
removal and sd.c has a lot of code shuffling to remove forward
declarations)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits)
scsi: ufs: core: No need to update UPIU.header.flags and lun in advanced RPMB handler
scsi: ufs: core: Add advanced RPMB support where UFSHCI 4.0 does not support EHS length in UTRD
scsi: mpt3sas: Remove volatile qualifier
scsi: mpt3sas: Perform additional retries if doorbell read returns 0
scsi: libsas: Simplify sas_queue_reset() and remove unused code
scsi: ufs: Fix the build for the old ARM OABI
scsi: qla2xxx: Fix unused variable warning in qla2xxx_process_purls_pkt()
scsi: fnic: Remove unused functions fnic_scsi_host_start/end_tag()
scsi: qla2xxx: Fix spelling mistake "tranport" -> "transport"
scsi: fnic: Replace sgreset tag with max_tag_id
scsi: qla2xxx: Remove unused variables in qla24xx_build_scsi_type_6_iocbs()
scsi: qla2xxx: Fix nvme_fc_rcv_ls_req() undefined error
scsi: smartpqi: Change driver version to 2.1.24-046
scsi: smartpqi: Enhance error messages
scsi: smartpqi: Enhance controller offline notification
scsi: smartpqi: Enhance shutdown notification
scsi: smartpqi: Simplify lun_number assignment
scsi: smartpqi: Rename pciinfo to pci_info
scsi: smartpqi: Rename MACRO to clarify purpose
scsi: smartpqi: Add abort handler
...
|
|
Add missing OID to the registry. Some servers and clients (including
Windows) now request "NEGOEX - SPNEGEO Extended Negotiation Security")
See https://datatracker.ietf.org/doc/html/draft-zhu-negoex-02
Reviewed-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Pull xarray fixes from Matthew Wilcox:
- Fix a bug encountered by people using bittorrent where they'd get
NULL pointer dereferences on page cache lookups when using XFS
- Two documentation fixes
* tag 'xarray-6.6' of git://git.infradead.org/users/willy/xarray:
idr: fix param name in idr_alloc_cyclic() doc
xarray: Document necessary flag in alloc functions
XArray: Do not return sibling entries from xa_load()
|
|
Now that eventfs structure is used to create the events directory via the
eventfs dynamically allocate code, the "dir" field of the trace_event_file
structure is no longer used. Remove it.
Link: https://lkml.kernel.org/r/20230908022001.580400115@goodmis.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ajay Kaher <akaher@vmware.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more thermal control updates from Rafael Wysocki:
"Eliminate an obsolete thermal zone registration function"
* tag 'thermal-6.6-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: core: Drop thermal_zone_device_register()
thermal: Use thermal_tripless_zone_device_register()
thermal: core: Add function for registering tripless thermal zones
thermal: core: Clean up headers of thermal zone registration functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Allow usage of LSX/LASX in the kernel, and use them for
SIMD-optimized RAID5/RAID6 routines
- Add Loongson Binary Translation (LBT) extension support
- Add basic KGDB & KDB support
- Add building with kcov coverage
- Add KFENCE (Kernel Electric-Fence) support
- Add KASAN (Kernel Address Sanitizer) support
- Some bug fixes and other small changes
- Update the default config file
* tag 'loongarch-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson: (25 commits)
LoongArch: Update Loongson-3 default config file
LoongArch: Add KASAN (Kernel Address Sanitizer) support
LoongArch: Simplify the processing of jumping new kernel for KASLR
kasan: Add (pmd|pud)_init for LoongArch zero_(pud|p4d)_populate process
kasan: Add __HAVE_ARCH_SHADOW_MAP to support arch specific mapping
LoongArch: Add KFENCE (Kernel Electric-Fence) support
LoongArch: Get partial stack information when providing regs parameter
LoongArch: mm: Add page table mapped mode support for virt_to_page()
kfence: Defer the assignment of the local variable addr
LoongArch: Allow building with kcov coverage
LoongArch: Provide kaslr_offset() to get kernel offset
LoongArch: Add basic KGDB & KDB support
LoongArch: Add Loongson Binary Translation (LBT) extension support
raid6: Add LoongArch SIMD recovery implementation
raid6: Add LoongArch SIMD syndrome calculation
LoongArch: Add SIMD-optimized XOR routines
LoongArch: Allow usage of LSX/LASX in the kernel
LoongArch: Define symbol 'fault' as a local label in fpu.S
LoongArch: Adjust {copy, clear}_user exception handler behavior
LoongArch: Use static defined zero page rather than allocated
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking updates from Jakub Kicinski:
"Including fixes from netfilter and bpf.
Current release - regressions:
- eth: stmmac: fix failure to probe without MAC interface specified
Current release - new code bugs:
- docs: netlink: fix missing classic_netlink doc reference
Previous releases - regressions:
- deal with integer overflows in kmalloc_reserve()
- use sk_forward_alloc_get() in sk_get_meminfo()
- bpf_sk_storage: fix the missing uncharge in sk_omem_alloc
- fib: avoid warn splat in flow dissector after packet mangling
- skb_segment: call zero copy functions before using skbuff frags
- eth: sfc: check for zero length in EF10 RX prefix
Previous releases - always broken:
- af_unix: fix msg_controllen test in scm_pidfd_recv() for
MSG_CMSG_COMPAT
- xsk: fix xsk_build_skb() dereferencing possible ERR_PTR()
- netfilter:
- nft_exthdr: fix non-linear header modification
- xt_u32, xt_sctp: validate user space input
- nftables: exthdr: fix 4-byte stack OOB write
- nfnetlink_osf: avoid OOB read
- one more fix for the garbage collection work from last release
- igmp: limit igmpv3_newpack() packet size to IP_MAX_MTU
- bpf, sockmap: fix preempt_rt splat when using raw_spin_lock_t
- handshake: fix null-deref in handshake_nl_done_doit()
- ip: ignore dst hint for multipath routes to ensure packets are
hashed across the nexthops
- phy: micrel:
- correct bit assignments for cable test errata
- disable EEE according to the KSZ9477 errata
Misc:
- docs/bpf: document compile-once-run-everywhere (CO-RE) relocations
- Revert "net: macsec: preserve ingress frame ordering", it appears
to have been developed against an older kernel, problem doesn't
exist upstream"
* tag 'net-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (95 commits)
net: enetc: distinguish error from valid pointers in enetc_fixup_clear_rss_rfs()
Revert "net: team: do not use dynamic lockdep key"
net: hns3: remove GSO partial feature bit
net: hns3: fix the port information display when sfp is absent
net: hns3: fix invalid mutex between tc qdisc and dcb ets command issue
net: hns3: fix debugfs concurrency issue between kfree buffer and read
net: hns3: fix byte order conversion issue in hclge_dbg_fd_tcam_read()
net: hns3: Support query tx timeout threshold by debugfs
net: hns3: fix tx timeout issue
net: phy: Provide Module 4 KSZ9477 errata (DS80000754C)
netfilter: nf_tables: Unbreak audit log reset
netfilter: ipset: add the missing IP_SET_HASH_WITH_NET0 macro for ip_set_hash_netportnet.c
netfilter: nft_set_rbtree: skip sync GC for new elements in this transaction
netfilter: nf_tables: uapi: Describe NFTA_RULE_CHAIN_ID
netfilter: nfnetlink_osf: avoid OOB read
netfilter: nftables: exthdr: fix 4-byte stack OOB write
selftests/bpf: Check bpf_sk_storage has uncharged sk_omem_alloc
bpf: bpf_sk_storage: Fix the missing uncharge in sk_omem_alloc
bpf: bpf_sk_storage: Fix invalid wait context lockdep report
s390/bpf: Pass through tail call counter in trampolines
...
|
