Age | Commit message (Collapse) | Author | Files | Lines |
|
Commit c65c1877bd68 ("slub: use lockdep_assert_held") incorrectly
required that add_full() and remove_full() hold n->list_lock. The lock
is only taken when kmem_cache_debug(s), since that's the only time it
actually does anything.
Require that the lock only be taken under such a condition.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes, both -stable fodder. The O_SYNC bug is fairly
old..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix a kmap leak in virtio_console
fix O_SYNC|O_APPEND syncing the wrong range on write()
|
|
It actually goes back to 2004 ([PATCH] Concurrent O_SYNC write support)
when sync_page_range() had been introduced; generic_file_write{,v}() correctly
synced
pos_after_write - written .. pos_after_write - 1
but generic_file_aio_write() synced
pos_before_write .. pos_before_write + written - 1
instead. Which is not the same thing with O_APPEND, obviously.
A couple of years later correct variant had been killed off when
everything switched to use of generic_file_aio_write().
All users of generic_file_aio_write() are affected, and the same bug
has been copied into other instances of ->aio_write().
The fix is trivial; the only subtle point is that generic_write_sync()
ought to be inlined to avoid calculations useless for the majority of
calls.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"Quite a varied little collection of fixes. Most of them are
relatively small or isolated; the biggest one is Mel Gorman's fixes
for TLB range flushing.
A couple of AMD-related fixes (including not crashing when given an
invalid microcode image) and fix a crash when compiled with gcov"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Unify valid container checks
x86, hweight: Fix BUG when booting with CONFIG_GCOV_PROFILE_ALL=y
x86/efi: Allow mapping BGRT on x86-32
x86: Fix the initialization of physnode_map
x86, cpu hotplug: Fix stack frame warning in check_irq_vectors_for_cpu_disable()
x86/intel/mid: Fix X86_INTEL_MID dependencies
arch/x86/mm/srat: Skip NUMA_NO_NODE while parsing SLIT
mm, x86: Revisit tlb_flushall_shift tuning for page flushes except on IvyBridge
x86: mm: change tlb_flushall_shift for IvyBridge
x86/mm: Eliminate redundant page table walk during TLB range flushing
x86/mm: Clean up inconsistencies when flushing TLB ranges
mm, x86: Account for TLB flushes only when debugging
x86/AMD/NB: Fix amd_set_subcaches() parameter type
x86/quirks: Add workaround for AMD F16h Erratum792
x86, doc, kconfig: Fix dud URL for Microcode data
|
|
* Avoid WARN_ON() when mapping BGRT on Baytrail (EFI 32-bit).
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
spin_lock_irq()
During aio stress test, we observed the following lockdep warning. This
mean AIO+numa_balancing is currently deadlockable.
The problem is, aio_migratepage disable interrupt, but
__set_page_dirty_nobuffers unintentionally enable it again.
Generally, all helper function should use spin_lock_irqsave() instead of
spin_lock_irq() because they don't know caller at all.
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&ctx->completion_lock)->rlock);
<Interrupt>
lock(&(&ctx->completion_lock)->rlock);
*** DEADLOCK ***
dump_stack+0x19/0x1b
print_usage_bug+0x1f7/0x208
mark_lock+0x21d/0x2a0
mark_held_locks+0xb9/0x140
trace_hardirqs_on_caller+0x105/0x1d0
trace_hardirqs_on+0xd/0x10
_raw_spin_unlock_irq+0x2c/0x50
__set_page_dirty_nobuffers+0x8c/0xf0
migrate_page_copy+0x434/0x540
aio_migratepage+0xb1/0x140
move_to_new_page+0x7d/0x230
migrate_pages+0x5e5/0x700
migrate_misplaced_page+0xbc/0xf0
do_numa_page+0x102/0x190
handle_pte_fault+0x241/0x970
handle_mm_fault+0x265/0x370
__do_page_fault+0x172/0x5a0
do_page_fault+0x1a/0x70
page_fault+0x28/0x30
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
swapoff clear swap_info's SWP_USED flag prematurely and free its
resources after that. A concurrent swapon will reuse this swap_info
while its previous resources are not cleared completely.
These late freed resources are:
- p->percpu_cluster
- swap_cgroup_ctrl[type]
- block_device setting
- inode->i_flags &= ~S_SWAPFILE
This patch clears the SWP_USED flag after all its resources are freed,
so that swapon can reuse this swap_info by alloc_swap_info() safely.
[akpm@linux-foundation.org: tidy up code comment]
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a patch to improve swap readahead algorithm. It's from Hugh and
I slightly changed it.
Hugh's original changelog:
swapin readahead does a blind readahead, whether or not the swapin is
sequential. This may be ok on harddisk, because large reads have
relatively small costs, and if the readahead pages are unneeded they can
be reclaimed easily - though, what if their allocation forced reclaim of
useful pages? But on SSD devices large reads are more expensive than
small ones: if the readahead pages are unneeded, reading them in caused
significant overhead.
This patch adds very simplistic random read detection. Stealing the
PageReadahead technique from Konstantin Khlebnikov's patch, avoiding the
vma/anon_vma sophistications of Shaohua Li's patch, swapin_nr_pages()
simply looks at readahead's current success rate, and narrows or widens
its readahead window accordingly. There is little science to its
heuristic: it's about as stupid as can be whilst remaining effective.
The table below shows elapsed times (in centiseconds) when running a
single repetitive swapping load across a 1000MB mapping in 900MB ram
with 1GB swap (the harddisk tests had taken painfully too long when I
used mem=500M, but SSD shows similar results for that).
Vanilla is the 3.6-rc7 kernel on which I started; Shaohua denotes his
Sep 3 patch in mmotm and linux-next; HughOld denotes my Oct 1 patch
which Shaohua showed to be defective; HughNew this Nov 14 patch, with
page_cluster as usual at default of 3 (8-page reads); HughPC4 this same
patch with page_cluster 4 (16-page reads); HughPC0 with page_cluster 0
(1-page reads: no readahead).
HDD for swapping to harddisk, SSD for swapping to VertexII SSD. Seq for
sequential access to the mapping, cycling five times around; Rand for
the same number of random touches. Anon for a MAP_PRIVATE anon mapping;
Shmem for a MAP_SHARED anon mapping, equivalent to tmpfs.
One weakness of Shaohua's vma/anon_vma approach was that it did not
optimize Shmem: seen below. Konstantin's approach was perhaps mistuned,
50% slower on Seq: did not compete and is not shown below.
HDD Vanilla Shaohua HughOld HughNew HughPC4 HughPC0
Seq Anon 73921 76210 75611 76904 78191 121542
Seq Shmem 73601 73176 73855 72947 74543 118322
Rand Anon 895392 831243 871569 845197 846496 841680
Rand Shmem 1058375 1053486 827935 764955 764376 756489
SSD Vanilla Shaohua HughOld HughNew HughPC4 HughPC0
Seq Anon 24634 24198 24673 25107 21614 70018
Seq Shmem 24959 24932 25052 25703 22030 69678
Rand Anon 43014 26146 28075 25989 26935 25901
Rand Shmem 45349 45215 28249 24268 24138 24332
These tests are, of course, two extremes of a very simple case: under
heavier mixed loads I've not yet observed any consistent improvement or
degradation, and wider testing would be welcome.
Shaohua Li:
Test shows Vanilla is slightly better in sequential workload than Hugh's
patch. I observed with Hugh's patch sometimes the readahead size is
shrinked too fast (from 8 to 1 immediately) in sequential workload if
there is no hit. And in such case, continuing doing readahead is good
actually.
I don't prepare a sophisticated algorithm for the sequential workload
because so far we can't guarantee sequential accessed pages are swap out
sequentially. So I slightly change Hugh's heuristic - don't shrink
readahead size too fast.
Here is my test result (unit second, 3 runs average):
Vanilla Hugh New
Seq 356 370 360
Random 4525 2447 2444
Attached graph is the swapin/swapout throughput I collected with 'vmstat
2'. The first part is running a random workload (till around 1200 of
the x-axis) and the second part is running a sequential workload.
swapin and swapout throughput are almost identical in steady state in
both workloads. These are expected behavior. while in Vanilla, swapin
is much bigger than swapout especially in random workload (because wrong
readahead).
Original patches by: Shaohua Li and Konstantin Khlebnikov.
[fengguang.wu@intel.com: swapin_nr_pages() can be static]
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux
Pull SLAB changes from Pekka Enberg:
"Random bug fixes that have accumulated in my inbox over the past few
months"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
mm: Fix warning on make htmldocs caused by slab.c
mm: slub: work around unneeded lockdep warning
mm: sl[uo]b: fix misleading comments
slub: Fix possible format string bug.
slub: use lockdep_assert_held
slub: Fix calculation of cpu slabs
slab.h: remove duplicate kmalloc declaration and fix kernel-doc warnings
|
|
This patch fixed following errors while make htmldocs
Warning(/mm/slab.c:1956): No description found for parameter 'page'
Warning(/mm/slab.c:1956): Excess function parameter 'slabp' description in 'slab_destroy'
Incorrect function parameter "slabp" was set instead of "page"
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
|
|
The slub code does some setup during early boot in
early_kmem_cache_node_alloc() with some local data. There is no
possible way that another CPU can see this data, so the slub code
doesn't unnecessarily lock it. However, some new lockdep asserts
check to make sure that add_partial() _always_ has the list_lock
held.
Just add the locking, even though it is technically unnecessary.
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
|
|
Commit 842e2873697e ("memcg: get rid of kmem_cache_dup()") introduced a
mutex for memcg_create_kmem_cache() to protect the tmp_name buffer that
holds the memcg name. It failed to unlock the mutex if this buffer
could not be allocated.
This patch fixes the issue by appropriately unlocking the mutex if the
allocation fails.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Glauber Costa <glommer@parallels.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A 3% of system memory bonus is sometimes too excessive in comparison to
other processes.
With commit a63d83f427fb ("oom: badness heuristic rewrite"), the OOM
killer tries to avoid killing privileged tasks by subtracting 3% of
overall memory (system or cgroup) from their per-task consumption. But
as a result, all root tasks that consume less than 3% of overall memory
are considered equal, and so it only takes 33+ privileged tasks pushing
the system out of memory for the OOM killer to do something stupid and
kill dhclient or other root-owned processes. For example, on a 32G
machine it can't tell the difference between the 1M agetty and the 10G
fork bomb member.
The changelog describes this 3% boost as the equivalent to the global
overcommit limit being 3% higher for privileged tasks, but this is not
the same as discounting 3% of overall memory from _every privileged task
individually_ during OOM selection.
Replace the 3% of system memory bonus with a 3% of current memory usage
bonus.
By giving root tasks a bonus that is proportional to their actual size,
they remain comparable even when relatively small. In the example
above, the OOM killer will discount the 1M agetty's 256 badness points
down to 179, and the 10G fork bomb's 262144 points down to 183500 points
and make the right choice, instead of discounting both to 0 and killing
agetty because it's first in the task list.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit abca7c496584 ("mm: fix slab->page _count corruption when using
slub") notes that we can not _set_ a page->counters directly, except
when using a real double-cmpxchg. Doing so can lose updates to
->_count.
That is an absolute rule:
You may not *set* page->counters except via a cmpxchg.
Commit abca7c496584 fixed this for the folks who have the slub
cmpxchg_double code turned off at compile time, but it left the bad case
alone. It can still be reached, and the same bug triggered in two
cases:
1. Turning on slub debugging at runtime, which is available on
the distro kernels that I looked at.
2. On 64-bit CPUs with no CMPXCHG16B (some early AMD x86-64
cpus, evidently)
There are at least 3 ways we could fix this:
1. Take all of the exising calls to cmpxchg_double_slab() and
__cmpxchg_double_slab() and convert them to take an old, new
and target 'struct page'.
2. Do (1), but with the newly-introduced 'slub_data'.
3. Do some magic inside the two cmpxchg...slab() functions to
pull the counters out of new_counters and only set those
fields in page->{inuse,frozen,objects}.
I've done (2) as well, but it's a bunch more code. This patch is an
attempt at (3). This was the most straightforward and foolproof way
that I could think to do this.
This would also technically allow us to get rid of the ugly
#if defined(CONFIG_HAVE_CMPXCHG_DOUBLE) && \
defined(CONFIG_HAVE_ALIGNED_STRUCT_PAGE)
in 'struct page', but leaving it alone has the added benefit that
'counters' stays 'unsigned' instead of 'unsigned long', so all the
copies that the slub code does stay a bit smaller.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As a result of commit 5606e3877ad8 ("mm: numa: Migrate on reference
policy"), /proc/<pid>/numa_maps prints the mempolicy for any <pid> as
"prefer:N" for the local node, N, of the process reading the file.
This should only be printed when the mempolicy of <pid> is
MPOL_PREFERRED for node N.
If the process is actually only using the default mempolicy for local
node allocation, make sure "default" is printed as expected.
Signed-off-by: David Rientjes <rientjes@google.com>
Reported-by: Robert Lippert <rlippert@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add my copyright to the zsmalloc source code which I maintain.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch moves zsmalloc under mm directory.
Before that, description will explain why we have needed custom
allocator.
Zsmalloc is a new slab-based memory allocator for storing compressed
pages. It is designed for low fragmentation and high allocation success
rate on large object, but <= PAGE_SIZE allocations.
zsmalloc differs from the kernel slab allocator in two primary ways to
achieve these design goals.
zsmalloc never requires high order page allocations to back slabs, or
"size classes" in zsmalloc terms. Instead it allows multiple
single-order pages to be stitched together into a "zspage" which backs
the slab. This allows for higher allocation success rate under memory
pressure.
Also, zsmalloc allows objects to span page boundaries within the zspage.
This allows for lower fragmentation than could be had with the kernel
slab allocator for objects between PAGE_SIZE/2 and PAGE_SIZE. With the
kernel slab allocator, if a page compresses to 60% of it original size,
the memory savings gained through compression is lost in fragmentation
because another object of the same size can't be stored in the leftover
space.
This ability to span pages results in zsmalloc allocations not being
directly addressable by the user. The user is given an
non-dereferencable handle in response to an allocation request. That
handle must be mapped, using zs_map_object(), which returns a pointer to
the mapped region that can be used. The mapping is necessary since the
object data may reside in two different noncontigious pages.
The zsmalloc fulfills the allocation needs for zram perfectly
[sjenning@linux.vnet.ibm.com: borrow Seth's quote]
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Nitin Gupta <ngupta@vflare.org>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Luigi Semenzato <semenzato@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull core block IO changes from Jens Axboe:
"The major piece in here is the immutable bio_ve series from Kent, the
rest is fairly minor. It was supposed to go in last round, but
various issues pushed it to this release instead. The pull request
contains:
- Various smaller blk-mq fixes from different folks. Nothing major
here, just minor fixes and cleanups.
- Fix for a memory leak in the error path in the block ioctl code
from Christian Engelmayer.
- Header export fix from CaiZhiyong.
- Finally the immutable biovec changes from Kent Overstreet. This
enables some nice future work on making arbitrarily sized bios
possible, and splitting more efficient. Related fixes to immutable
bio_vecs:
- dm-cache immutable fixup from Mike Snitzer.
- btrfs immutable fixup from Muthu Kumar.
- bio-integrity fix from Nic Bellinger, which is also going to stable"
* 'for-3.14/core' of git://git.kernel.dk/linux-block: (44 commits)
xtensa: fixup simdisk driver to work with immutable bio_vecs
block/blk-mq-cpu.c: use hotcpu_notifier()
blk-mq: for_each_* macro correctness
block: Fix memory leak in rw_copy_check_uvector() handling
bio-integrity: Fix bio_integrity_verify segment start bug
block: remove unrelated header files and export symbol
blk-mq: uses page->list incorrectly
blk-mq: use __smp_call_function_single directly
btrfs: fix missing increment of bi_remaining
Revert "block: Warn and free bio if bi_end_io is not set"
block: Warn and free bio if bi_end_io is not set
blk-mq: fix initializing request's start time
block: blk-mq: don't export blk_mq_free_queue()
block: blk-mq: make blk_sync_queue support mq
block: blk-mq: support draining mq queue
dm cache: increment bi_remaining when bi_end_io is restored
block: fixup for generic bio chaining
block: Really silence spurious compiler warnings
block: Silence spurious compiler warnings
block: Kill bio_pair_split()
...
|
|
In original bootmem wrapper for memblock, we have limit checking.
Add it to memblock_virt_alloc, to address arm and x86 booting crash.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Reported-by: Olof Johansson <olof@lixom.net>
Tested-by: Olof Johansson <olof@lixom.net>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: "Strashko, Grygorii" <grygorii.strashko@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 63d0f0a3c7e1 ("mm/readahead.c:do_readhead(): don't check for
->readpage") unintentionally made do_readahead return 0 for all valid
files regardless of whether readahead was supported, rather than the
expected -EINVAL. This gets forwarded on to userspace, and results in
sys_readahead appearing to succeed in cases that don't make sense (e.g.
when called on pipes or sockets). This issue is detected by the LTP
readahead01 testcase.
As the exact return value of force_page_cache_readahead is currently
never used, we can simplify it to return only 0 or -EINVAL (when
readpage or readpages is missing). With that in place we can simply
forward on the return value of force_page_cache_readahead in
do_readahead.
This patch performs said change, restoring the expected semantics.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 309381feaee5 ("mm: dump page when hitting a VM_BUG_ON using
VM_BUG_ON_PAGE") added a bunch of VM_BUG_ON_PAGE() calls.
But, most of the ones in the slub code are for _temporary_ 'struct
page's which are declared on the stack and likely have lots of gunk in
them. Dumping their contents out will just confuse folks looking at
bad_page() output. Plus, if we try to page_to_pfn() on them or
soemthing, we'll probably oops anyway.
Turn them back in to VM_BUG_ON()s.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On kmem_cache_create_memcg() error path we set 'err', but leave 's' (the
new cache ptr) undefined. The latter can be NULL if we could not
allocate the cache, or pointing to a freed area if we failed somewhere
later while trying to initialize it. Initially we checked 'err'
immediately before exiting the function and returned NULL if it was set
ignoring the value of 's':
out_unlock:
...
if (err) {
/* report error */
return NULL;
}
return s;
Recently this check was, in fact, broken by commit f717eb3abb5e ("slab:
do not panic if we fail to create memcg cache"), which turned it to:
out_unlock:
...
if (err && !memcg) {
/* report error */
return NULL;
}
return s;
As a result, if we are failing creating a cache for a memcg, we will
skip the check and return 's' that can contain crap. Obviously, commit
f717eb3abb5e intended not to return crap on error allocating a cache for
a memcg, but only to remove the error reporting in this case, so the
check should look like this:
out_unlock:
...
if (err) {
if (!memcg)
return NULL;
/* report error */
return NULL;
}
return s;
[rientjes@google.com: despaghettification]
[vdavydov@parallels.com: patch monkeying]
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Reported-by: Dave Jones <davej@redhat.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A few printk(KERN_*'s have snuck in there.
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The command line parsing takes place before jump labels are initialised
which generates a warning if numa_balancing= is specified and
CONFIG_JUMP_LABEL is set.
On older kernels before commit c4b2c0c5f647 ("static_key: WARN on usage
before jump_label_init was called") the kernel would have crashed. This
patch enables automatic numa balancing later in the initialisation
process if numa_balancing= is specified.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The VM is currently heavily tuned to avoid swapping. Whether that is
good or bad is a separate discussion, but as long as the VM won't swap
to make room for dirty cache, we can not consider anonymous pages when
calculating the amount of dirtyable memory, the baseline to which
dirty_background_ratio and dirty_ratio are applied.
A simple workload that occupies a significant size (40+%, depending on
memory layout, storage speeds etc.) of memory with anon/tmpfs pages and
uses the remainder for a streaming writer demonstrates this problem. In
that case, the actual cache pages are a small fraction of what is
considered dirtyable overall, which results in an relatively large
portion of the cache pages to be dirtied. As kswapd starts rotating
these, random tasks enter direct reclaim and stall on IO.
Only consider free pages and file pages dirtyable.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Tested-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Tejun reported stuttering and latency spikes on a system where random
tasks would enter direct reclaim and get stuck on dirty pages. Around
50% of memory was occupied by tmpfs backed by an SSD, and another disk
(rotating) was reading and writing at max speed to shrink a partition.
: The problem was pretty ridiculous. It's a 8gig machine w/ one ssd and 10k
: rpm harddrive and I could reliably reproduce constant stuttering every
: several seconds for as long as buffered IO was going on on the hard drive
: either with tmpfs occupying somewhere above 4gig or a test program which
: allocates about the same amount of anon memory. Although swap usage was
: zero, turning off swap also made the problem go away too.
:
: The trigger conditions seem quite plausible - high anon memory usage w/
: heavy buffered IO and swap configured - and it's highly likely that this
: is happening in the wild too. (this can happen with copying large files
: to usb sticks too, right?)
This patch (of 2):
The dirty_balance_reserve is an approximation of the fraction of free
pages that the page allocator does not make available for page cache
allocations. As a result, it has to be taken into account when
calculating the amount of "dirtyable memory", the baseline to which
dirty_background_ratio and dirty_ratio are applied.
However, currently the reserve is subtracted from the sum of free and
reclaimable pages, which is non-sensical and leads to erroneous results
when the system is dominated by unreclaimable pages and the
dirty_balance_reserve is bigger than free+reclaimable. In that case, at
least the already allocated cache should be considered dirtyable.
Fix the calculation by subtracting the reserve from the amount of free
pages, then adding the reclaimable pages on top.
[akpm@linux-foundation.org: fix CONFIG_HIGHMEM build]
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Tested-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs updates from Al Viro:
"Assorted stuff; the biggest pile here is Christoph's ACL series. Plus
assorted cleanups and fixes all over the place...
There will be another pile later this week"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (43 commits)
__dentry_path() fixes
vfs: Remove second variable named error in __dentry_path
vfs: Is mounted should be testing mnt_ns for NULL or error.
Fix race when checking i_size on direct i/o read
hfsplus: remove can_set_xattr
nfsd: use get_acl and ->set_acl
fs: remove generic_acl
nfs: use generic posix ACL infrastructure for v3 Posix ACLs
gfs2: use generic posix ACL infrastructure
jfs: use generic posix ACL infrastructure
xfs: use generic posix ACL infrastructure
reiserfs: use generic posix ACL infrastructure
ocfs2: use generic posix ACL infrastructure
jffs2: use generic posix ACL infrastructure
hfsplus: use generic posix ACL infrastructure
f2fs: use generic posix ACL infrastructure
ext2/3/4: use generic posix ACL infrastructure
btrfs: use generic posix ACL infrastructure
fs: make posix_acl_create more useful
fs: make posix_acl_chmod more useful
...
|
|
Merge misc updates from Andrew Morton:
- a few hotfixes
- dynamic-debug updates
- ipc updates
- various other sweepings off the factory floor
* akpm: (31 commits)
firmware/google: drop 'select EFI' to avoid recursive dependency
compat: fix sys_fanotify_mark
checkpatch.pl: check for function declarations without arguments
mm/migrate.c: fix setting of cpupid on page migration twice against normal page
softirq: use const char * const for softirq_to_name, whitespace neatening
softirq: convert printks to pr_<level>
softirq: use ffs() in __do_softirq()
kernel/kexec.c: use vscnprintf() instead of vsnprintf() in vmcoreinfo_append_str()
splice: fix unexpected size truncation
ipc: fix compat msgrcv with negative msgtyp
ipc,msg: document barriers
ipc: delete seq_max field in struct ipc_ids
ipc: simplify sysvipc_proc_open() return
ipc: remove useless return statement
ipc: remove braces for single statements
ipc: standardize code comments
ipc: whitespace cleanup
ipc: change kern_ipc_perm.deleted type to bool
ipc: introduce ipc_valid_object() helper to sort out IPC_RMID races
ipc/sem.c: avoid overflow of semop undo (semadj) value
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc updates from Ben Herrenschmidt:
"So here's my next branch for powerpc. A bit late as I was on vacation
last week. It's mostly the same stuff that was in next already, I
just added two patches today which are the wiring up of lockref for
powerpc, which for some reason fell through the cracks last time and
is trivial.
The highlights are, in addition to a bunch of bug fixes:
- Reworked Machine Check handling on kernels running without a
hypervisor (or acting as a hypervisor). Provides hooks to handle
some errors in real mode such as TLB errors, handle SLB errors,
etc...
- Support for retrieving memory error information from the service
processor on IBM servers running without a hypervisor and routing
them to the memory poison infrastructure.
- _PAGE_NUMA support on server processors
- 32-bit BookE relocatable kernel support
- FSL e6500 hardware tablewalk support
- A bunch of new/revived board support
- FSL e6500 deeper idle states and altivec powerdown support
You'll notice a generic mm change here, it has been acked by the
relevant authorities and is a pre-req for our _PAGE_NUMA support"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (121 commits)
powerpc: Implement arch_spin_is_locked() using arch_spin_value_unlocked()
powerpc: Add support for the optimised lockref implementation
powerpc/powernv: Call OPAL sync before kexec'ing
powerpc/eeh: Escalate error on non-existing PE
powerpc/eeh: Handle multiple EEH errors
powerpc: Fix transactional FP/VMX/VSX unavailable handlers
powerpc: Don't corrupt transactional state when using FP/VMX in kernel
powerpc: Reclaim two unused thread_info flag bits
powerpc: Fix races with irq_work
Move precessing of MCE queued event out from syscall exit path.
pseries/cpuidle: Remove redundant call to ppc64_runlatch_off() in cpu idle routines
powerpc: Make add_system_ram_resources() __init
powerpc: add SATA_MV to ppc64_defconfig
powerpc/powernv: Increase candidate fw image size
powerpc: Add debug checks to catch invalid cpu-to-node mappings
powerpc: Fix the setup of CPU-to-Node mappings during CPU online
powerpc/iommu: Don't detach device without IOMMU group
powerpc/eeh: Hotplug improvement
powerpc/eeh: Call opal_pci_reinit() on powernv for restoring config space
powerpc/eeh: Add restore_config operation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc
Pull powerpc mremap fix from Ben Herrenschmidt:
"This is the patch that I had sent after -rc8 and which we decided to
wait before merging. It's based on a different tree than my -next
branch (it needs some pre-reqs that were in -rc4 or so while my -next
is based on -rc1) so I left it as a separate branch for your to pull.
It's identical to the request I did 2 or 3 weeks back.
This fixes crashes in mremap with THP on powerpc.
The fix however requires a small change in the generic code. It moves
a condition into a helper we can override from the arch which is
harmless, but it *also* slightly changes the order of the set_pmd and
the withdraw & deposit, which should be fine according to Kirill (who
wrote that code) but I agree -rc8 is a bit late...
It was acked by Kirill and Andrew told me to just merge it via powerpc"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/thp: Fix crash on mremap
|
|
Commit 7851a45cd3f6 ("mm: numa: Copy cpupid on page migration") copies
over the cpupid at page migration time. It is unnecessary to set it
again in alloc_misplaced_dst_page().
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit da29bd36224b ("mm/mm_init.c: make creation of the mm_kobj happen
earlier than device_initcall") changed to pure_initcall(mm_sysfs_init).
That's too early: mm_sysfs_init() depends on core_initcall(ksysfs_init)
to have made the kernel_kobj directory "kernel" in which to create "mm".
Make it postcore_initcall(mm_sysfs_init). We could use core_initcall(),
and depend upon Makefile link order kernel/ mm/ fs/ ipc/ security/ ...
as core_initcall(debugfs_init) and core_initcall(securityfs_init) do;
but better not.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Revert commit ece86e222db4, which was intended as a small performance
improvement.
Despite the claim that the patch doesn't introduce any functional
changes in fact it does.
The "no page" path behaves different now. Originally, vmalloc_to_page
might return NULL under some conditions, with new implementation it
returns pfn_to_page(0) which is not the same as NULL.
Simple test shows the difference.
test.c
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/vmalloc.h>
#include <linux/mm.h>
int __init myi(void)
{
struct page *p;
void *v;
v = vmalloc(PAGE_SIZE);
/* trigger the "no page" path in vmalloc_to_page*/
vfree(v);
p = vmalloc_to_page(v);
pr_err("expected val = NULL, returned val = %p", p);
return -EBUSY;
}
void __exit mye(void)
{
}
module_init(myi)
module_exit(mye)
Before interchange:
expected val = NULL, returned val = (null)
After interchange:
expected val = NULL, returned val = c7ebe000
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Cc: Jianyu Zhan <nasa4836@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In original __alloc_memory_core_early() for bootmem wrapper, we do not
align size silently.
We should not do that, as later free with old size will leave some range
not freed.
It's obvious that code is copied from memblock_base_nid(), and that code
is wrong for the same reason.
Also remove that in memblock_alloc_base.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
So far I've had one ACK for this, and no other comments. So I think it
is probably time to send this via some suitable tree. I'm guessing that
the vfs tree would be the most appropriate route, but not sure that
there is one at the moment (don't see anything recent at kernel.org)
so in that case I think -mm is the "back up plan". Al, please let me
know if you will take this?
Steve.
---------------------
Following on from the "Re: [PATCH v3] vfs: fix a bug when we do some dio
reads with append dio writes" thread on linux-fsdevel, this patch is my
current version of the fix proposed as option (b) in that thread.
Removing the i_size test from the direct i/o read path at vfs level
means that filesystems now have to deal with requests which are beyond
i_size themselves. These I've divided into three sets:
a) Those with "no op" ->direct_IO (9p, cifs, ceph)
These are obviously not going to be an issue
b) Those with "home brew" ->direct_IO (nfs, fuse)
I've been told that NFS should not have any problem with the larger
i_size, however I've added an extra test to FUSE to duplicate the
original behaviour just to be on the safe side.
c) Those using __blockdev_direct_IO()
These call through to ->get_block() which should deal with the EOF
condition correctly. I've verified that with GFS2 and I believe that
Zheng has verified it for ext4. I've also run the test on XFS and it
passes both before and after this change.
The part of the patch in filemap.c looks a lot larger than it really is
- there are only two lines of real change. The rest is just indentation
of the contained code.
There remains a test of i_size though, which was added for btrfs. It
doesn't cause the other filesystems a problem as the test is performed
after ->direct_IO has been called. It is possible that there is a race
that does matter to btrfs, however this patch doesn't change that, so
its still an overall improvement.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Reported-by: Zheng Liu <gnehzuil.liu@gmail.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Acked-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
And instead convert tmpfs to use the new generic ACL code, with two stub
methods provided for in-memory filesystems.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Merge in the x86 changes to apply a fix.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Bisection between 3.11 and 3.12 fingered commit 9824cf97 ("mm:
vmstats: tlb flush counters") to cause overhead problems.
The counters are undeniably useful but how often do we really
need to debug TLB flush related issues? It does not justify
taking the penalty everywhere so make it a debugging option.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Tested-by: Davidlohr Bueso <davidlohr@hp.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Alex Shi <alex.shi@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-XzxjntugxuwpxXhcrxqqh53b@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The VM_SOFTDIRTY bit affects vma merge routine: if two VMAs has all bits
in vm_flags matched except dirty bit the kernel can't longer merge them
and this forces the kernel to generate new VMAs instead.
It finally may lead to the situation when userspace application reaches
vm.max_map_count limit and get crashed in worse case
| (gimp:11768): GLib-ERROR **: gmem.c:110: failed to allocate 4096 bytes
|
| (file-tiff-load:12038): LibGimpBase-WARNING **: file-tiff-load: gimp_wire_read(): error
| xinit: connection to X server lost
|
| waiting for X server to shut down
| /usr/lib64/gimp/2.0/plug-ins/file-tiff-load terminated: Hangup
| /usr/lib64/gimp/2.0/plug-ins/script-fu terminated: Hangup
| /usr/lib64/gimp/2.0/plug-ins/script-fu terminated: Hangup
https://bugzilla.kernel.org/show_bug.cgi?id=67651
https://bugzilla.gnome.org/show_bug.cgi?id=719619#c0
Initial problem came from missed VM_SOFTDIRTY in do_brk() routine but
even if we would set up VM_SOFTDIRTY here, there is still a way to
prevent VMAs from merging: one can call
| echo 4 > /proc/$PID/clear_refs
and clear all VM_SOFTDIRTY over all VMAs presented in memory map, then
new do_brk() will try to extend old VMA and finds that dirty bit doesn't
match thus new VMA will be generated.
As discussed with Pavel, the right approach should be to ignore
VM_SOFTDIRTY bit when we're trying to merge VMAs and if merge successed
we mark extended VMA with dirty bit where needed.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Reported-by: Bastian Hougaard <gnome@rvzt.net>
Reported-by: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mm/rmap.c:851:9-10: WARNING: return of 0/1 in function 'invalid_mkclean_vma' with return type bool
Return statements in functions returning bool should use
true/false instead of 1/0.
Generated by: coccinelle/misc/boolreturn.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the second half of scan_swap_map()'s scan loop, offset is set to
si->lowest_bit and then incremented before entering the loop for the
first time, causing si->swap_map[si->lowest_bit] to be skipped.
Signed-off-by: Jamie Liu <jamieliu@google.com>
Cc: Shaohua Li <shli@fusionio.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Developers occasionally try and optimise PFN scanners by using
page_order but miss that in general it requires zone->lock. This has
happened twice for compaction.c and rejected both times. This patch
clarifies the documentation of page_order and adds a note to
compaction.c why page_order is not used.
[akpm@linux-foundation.org: tweaks]
[lauraa@codeaurora.org: Corrected a page_zone(page)->lock reference]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 19f39402864e ("memcg: simplify mem_cgroup_iter") has reorganized
mem_cgroup_iter code in order to simplify it. A part of that change was
dropping an optimization which didn't call css_tryget on the root of the
walked tree. The patch however didn't change the css_put part in
mem_cgroup_iter which excludes root.
This wasn't an issue at the time because __mem_cgroup_iter_next bailed
out for root early without taking a reference as cgroup iterators
(css_next_descendant_pre) didn't visit root themselves.
Nevertheless cgroup iterators have been reworked to visit root by commit
bd8815a6d802 ("cgroup: make css_for_each_descendant() and friends
include the origin css in the iteration") when the root bypass have been
dropped in __mem_cgroup_iter_next. This means that css_put is not
called for root and so css along with mem_cgroup and other cgroup
internal object tied by css lifetime are never freed.
Fix the issue by reintroducing root check in __mem_cgroup_iter_next and
do not take css reference for it.
This reference counting magic protects us also from another issue, an
endless loop reported by Hugh Dickins when reclaim races with root
removal and css_tryget called by iterator internally would fail. There
would be no other nodes to visit so __mem_cgroup_iter_next would return
NULL and mem_cgroup_iter would interpret it as "start looping from root
again" and so mem_cgroup_iter would loop forever internally.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Hugh Dickins <hughd@google.com>
Tested-by: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Hugh has reported an endless loop when the hardlimit reclaim sees the
same group all the time. This might happen when the reclaim races with
the memcg removal.
shrink_zone
[rmdir root]
mem_cgroup_iter(root, NULL, reclaim)
// prev = NULL
rcu_read_lock()
mem_cgroup_iter_load
last_visited = iter->last_visited // gets root || NULL
css_tryget(last_visited) // failed
last_visited = NULL [1]
memcg = root = __mem_cgroup_iter_next(root, NULL)
mem_cgroup_iter_update
iter->last_visited = root;
reclaim->generation = iter->generation
mem_cgroup_iter(root, root, reclaim)
// prev = root
rcu_read_lock
mem_cgroup_iter_load
last_visited = iter->last_visited // gets root
css_tryget(last_visited) // failed
[1]
The issue seemed to be introduced by commit 5f5781619718 ("memcg: relax
memcg iter caching") which has replaced unconditional css_get/css_put by
css_tryget/css_put for the cached iterator.
This patch fixes the issue by skipping css_tryget on the root of the
tree walk in mem_cgroup_iter_load and symmetrically doesn't release it
in mem_cgroup_iter_update.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Hugh Dickins <hughd@google.com>
Tested-by: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Greg Thelen <gthelen@google.com>
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When two threads have the same badness score, it's preferable to kill
the thread group leader so that the actual process name is printed to
the kernel log rather than the thread group name which may be shared
amongst several processes.
This was the behavior when select_bad_process() used to do
for_each_process(), but it now iterates threads instead and leads to
ambiguity.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It is surprising that the mem_cgroup iterator can return memcgs which
have not yet been fully initialized. By accident (or trial and error?)
this appears not to present an actual problem; but it may be better to
prevent such surprises, by skipping memcgs not yet online.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Shorten mem_cgroup_reclaim_iter.last_dead_count from unsigned long to
int: it's assigned from an int and compared with an int, and adjacent to
an unsigned int: so there's no point to it being unsigned long, which
wasted 104 bytes in every mem_cgroup_per_zone.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Code that is obj-y (always built-in) or dependent on a bool Kconfig
(built-in or absent) can never be modular. So using module_init as an
alias for __initcall can be somewhat misleading.
Fix these up now, so that we can relocate module_init from init.h into
module.h in the future. If we don't do this, we'd have to add module.h
to obviously non-modular code, and that would be a worse thing.
The audit targets the following module_init users for change:
mm/ksm.c bool KSM
mm/mmap.c bool MMU
mm/huge_memory.c bool TRANSPARENT_HUGEPAGE
mm/mmu_notifier.c bool MMU_NOTIFIER
Note that direct use of __initcall is discouraged, vs. one of the
priority categorized subgroups. As __initcall gets mapped onto
device_initcall, our use of subsys_initcall (which makes sense for these
files) will thus change this registration from level 6-device to level
4-subsys (i.e. slightly earlier).
However no observable impact of that difference has been observed during
testing.
One might think that core_initcall (l2) or postcore_initcall (l3) would
be more appropriate for anything in mm/ but if we look at some actual
init functions themselves, we see things like:
mm/huge_memory.c --> hugepage_init --> hugepage_init_sysfs
mm/mmap.c --> init_user_reserve --> sysctl_user_reserve_kbytes
mm/ksm.c --> ksm_init --> sysfs_create_group
and hence the choice of subsys_initcall (l4) seems reasonable, and at
the same time minimizes the risk of changing the priority too
drastically all at once. We can adjust further in the future.
Also, several instances of missing ";" at EOL are fixed.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The use of __initcall is to be eventually replaced by choosing one from
the prioritized groupings laid out in init.h header:
pure_initcall 0
core_initcall 1
postcore_initcall 2
arch_initcall 3
subsys_initcall 4
fs_initcall 5
device_initcall 6
late_initcall 7
In the interim, all __initcall are mapped onto device_initcall, which as
can be seen above, comes quite late in the ordering.
Currently the mm_kobj is created with __initcall in mm_sysfs_init().
This means that any other initcalls that want to reference the mm_kobj
have to be device_initcall (or later), otherwise we will for example,
trip the BUG_ON(!kobj) in sysfs's internal_create_group(). This
unfairly restricts those users; for example something that clearly makes
sense to be an arch_initcall will not be able to choose that.
However, upon examination, it is only this way for historical reasons
(i.e. simply not reprioritized yet). We see that sysfs is ready quite
earlier in init/main.c via:
vfs_caches_init
|_ mnt_init
|_ sysfs_init
well ahead of the processing of the prioritized calls listed above.
So we can recategorize mm_sysfs_init to be a pure_initcall, which in
turn allows any mm_kobj initcall users a wider range (1 --> 7) of
initcall priorities to choose from.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|