summaryrefslogtreecommitdiff
path: root/net/ethtool
AgeCommit message (Collapse)AuthorFilesLines
2022-10-04ethtool: add interface to interact with Ethernet Power EquipmentOleksij Rempel5-1/+209
Add interface to support Power Sourcing Equipment. At current step it provides generic way to address all variants of PSE devices as defined in IEEE 802.3-2018 but support only objects specified for IEEE 802.3-2018 104.4 PoDL Power Sourcing Equipment (PSE). Currently supported and mandatory objects are: IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl This is minimal interface needed to control PSE on each separate ethernet port but it provides not all mandatory objects specified in IEEE 802.3-2018. Since "PoDL PSE" and "PSE" have similar names, but some different values I decide to not merge them and keep separate naming schema. This should allow as to be as close to IEEE 802.3 spec as possible and avoid name conflicts in the future. This implementation is connected to PHYs instead of MACs because PSE auto classification can potentially interfere with PHY auto negotiation. So, may be some extra PHY related initialization will be needed. With WIP version of ethtools interaction with PSE capable link looks as following: $ ip l ... 5: t1l1@eth0: <BROADCAST,MULTICAST> .. ... $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: disabled PoDL PSE Power Detection Status: disabled $ ethtool --set-pse t1l1 podl-pse-admin-control enable $ ethtool --show-pse t1l1 PSE attributs for t1l1: PoDL PSE Admin State: enabled PoDL PSE Power Detection Status: delivering power Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Bagas Sanjaya <bagasdotme@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-23net: phy: Add support for rate matchingSean Anderson2-0/+6
This adds support for rate matching (also known as rate adaptation) to the phy subsystem. The general idea is that the phy interface runs at one speed, and the MAC throttles the rate at which it sends packets to the link speed. There's a good overview of several techniques for achieving this at [1]. This patch adds support for three: pause-frame based (such as in Aquantia phys), CRS-based (such as in 10PASS-TS and 2BASE-TL), and open-loop-based (such as in 10GBASE-W). This patch makes a few assumptions and a few non assumptions about the types of rate matching available. First, it assumes that different phys may use different forms of rate matching. Second, it assumes that phys can use rate matching for any of their supported link speeds (e.g. if a phy supports 10BASE-T and XGMII, then it can adapt XGMII to 10BASE-T). Third, it does not assume that all interface modes will use the same form of rate matching. Fourth, it does not assume that all phy devices will support rate matching (even if some do). Relaxing or strengthening these (non-)assumptions could result in a different API. For example, if all interface modes were assumed to use the same form of rate matching, then a bitmask of interface modes supportting rate matching would suffice. For some better visibility into the process, the current rate matching mode is exposed as part of the ethtool ksettings. For the moment, only read access is supported. I'm not sure what userspace might want to configure yet (disable it altogether, disable just one mode, specify the mode to use, etc.). For the moment, since only pause-based rate adaptation support is added in the next few commits, rate matching can be disabled altogether by adjusting the advertisement. 802.3 calls this feature "rate adaptation" in clause 49 (10GBASE-R) and "rate matching" in clause 61 (10PASS-TL and 2BASE-TS). Aquantia also calls this feature "rate adaptation". I chose "rate matching" because it is shorter, and because Russell doesn't think "adaptation" is correct in this context. Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-23ethtool: tunnels: check the return value of nla_nest_start()Li Zhong1-0/+2
Check the return value of nla_nest_start(). When starting the entry level nested attributes, if the tailroom of socket buffer is insufficient to store the attribute header and payload, the return value will be NULL. There is, however, no real bug here since if the skb is full nla_put_be16() will fail as well and we'll error out. Signed-off-by: Li Zhong <floridsleeves@gmail.com> Link: https://lore.kernel.org/r/20220921181716.1629541-1-floridsleeves@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-08-30ethtool: report missing header via ext_ack in the default handlerJakub Kicinski1-0/+3
The actual presence check for the header is in ethnl_parse_header_dev_get() but it's a few layers in, and already has a ton of arguments so let's just pick the low hanging fruit and check for missing header in the default request handler. Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-08-30ethtool: strset: report missing ETHTOOL_A_STRINGSET_ID via ext_ackJakub Kicinski1-1/+1
Strset needs ETHTOOL_A_STRINGSET_ID, use it as an example of reporting attrs missing in nests. Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-08-29genetlink: start to validate reserved header bytesJakub Kicinski1-0/+1
We had historically not checked that genlmsghdr.reserved is 0 on input which prevents us from using those precious bytes in the future. One use case would be to extend the cmd field, which is currently just 8 bits wide and 256 is not a lot of commands for some core families. To make sure that new families do the right thing by default put the onus of opting out of validation on existing families. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel) Signed-off-by: David S. Miller <davem@davemloft.net>
2022-08-23ethtool: move from strlcpy with unused retval to strscpyWolfram Sang1-4/+4
Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/ Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Link: https://lore.kernel.org/r/20220818210218.8443-1-wsa+renesas@sang-engineering.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-07-26net: delete extra space and tab in blank lineWilliam Dean1-1/+1
delete extra space and tab in blank line, there is no functional change. Reported-by: Hacash Robot <hacashRobot@santino.com> Signed-off-by: William Dean <williamsukatube@gmail.com> Link: https://lore.kernel.org/r/20220723073222.2961602-1-williamsukatube@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+1
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-18ethtool: Fix get module eeprom fallbackIvan Vecera1-1/+1
Function fallback_set_params() checks if the module type returned by a driver is ETH_MODULE_SFF_8079 and in this case it assumes that buffer returns a concatenated content of page A0h and A2h. The check is wrong because the correct type is ETH_MODULE_SFF_8472. Fixes: 96d971e307cc ("ethtool: Add fallback to get_module_eeprom from netlink command") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220616160856.3623273-1-ivecera@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-14ethtool: Fix and simplify ethtool_convert_link_mode_to_legacy_u32()Marco Bonelli1-15/+2
Fix the implementation of ethtool_convert_link_mode_to_legacy_u32(), which is supposed to return false if src has bits higher than 31 set. The current implementation uses the complement of bitmap_fill(ext, 32) to test high bits of src, which is wrong as bitmap_fill() fills _with long granularity_, and sizeof(long) can be > 4. No users of this function currently check the return value, so the bug was dormant. Also remove the check for __ETHTOOL_LINK_MODE_MASK_NBITS > 32, as the enum ethtool_link_mode_bit_indices contains far beyond 32 values. Using find_next_bit() to test the src bitmask works regardless of this anyway. Signed-off-by: Marco Bonelli <marco@mebeim.net> Link: https://lore.kernel.org/r/20220609134900.11201-1-marco@mebeim.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-06-10net: rename reference+tracking helpersJakub Kicinski3-6/+6
Netdev reference helpers have a dev_ prefix for historic reasons. Renaming the old helpers would be too much churn but we can rename the tracking ones which are relatively recent and should be the default for new code. Rename: dev_hold_track() -> netdev_hold() dev_put_track() -> netdev_put() dev_replace_track() -> netdev_ref_replace() Link: https://lore.kernel.org/r/20220608043955.919359-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-01ethtool: Add 10base-T1L link mode entryAlexandru Tachici1-0/+3
Add entry for the 10base-T1L full duplex mode. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-04-15net: ethtool: move checks before rtnl_lock() in ethnl_set_ringsJie Wang1-18/+18
Currently these two checks in ethnl_set_rings are added after rtnl_lock() which will do useless works if the request is invalid. So this patch moves these checks before the rtnl_lock() to avoid these costs. Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-15net: ethtool: extend ringparam set/get APIs for tx_pushJie Wang2-3/+17
Currently tx push is a standard driver feature which controls use of a fast path descriptor push. So this patch extends the ringparam APIs and data structures to support set/get tx push by ethtool -G/g. Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-24ethtool: add support to set/get completion queue event sizeSubbaraya Sundeep2-3/+18
Add support to set completion queue event size via ethtool -G parameter and get it via ethtool -g parameter. ~ # ./ethtool -G eth0 cqe-size 512 ~ # ./ethtool -g eth0 Ring parameters for eth0: Pre-set maximums: RX: 1048576 RX Mini: n/a RX Jumbo: n/a TX: 1048576 Current hardware settings: RX: 256 RX Mini: n/a RX Jumbo: n/a TX: 4096 RX Buf Len: 2048 CQE Size: 128 Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-28ethtool: add header/data split indicationJakub Kicinski1-5/+10
For applications running on a mix of platforms it's useful to have a clear indication whether host's NIC supports the geometry requirements of TCP zero-copy. TCP zero-copy Rx requires data to be neatly placed into memory pages. Most NICs can't do that. This patch is adding GET support only, since the NICs I work with either always have the feature enabled or enable it whenever MTU is set to jumbo. In other words I don't need SET. But adding set should be trivial. (The only note on SET is that we will likely want the setting to be "sticky" and use 0 / `unknown` to reset it back to driver default.) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-06ethtool: use phydev variableTom Rix1-4/+4
In ethtool_get_phy_stats(), the phydev varaible is set to dev->phydev but dev->phydev is still used. Replace dev->phydev uses with phydev. Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-05netlink: do not allocate a device refcount tracker in ethnl_default_notify()Eric Dumazet1-1/+0
As reported by Johannes, the tracker allocated in ethnl_default_notify() is not really needed, as this function is not expected to change a device reference count. Fixes: e4b8954074f6 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20220105170849.2610470-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller1-0/+1
Alexei Starovoitov says: ==================== pull-request: bpf-next 2021-12-30 The following pull-request contains BPF updates for your *net-next* tree. We've added 72 non-merge commits during the last 20 day(s) which contain a total of 223 files changed, 3510 insertions(+), 1591 deletions(-). The main changes are: 1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii. 2) Beautify and de-verbose verifier logs, from Christy. 3) Composable verifier types, from Hao. 4) bpf_strncmp helper, from Hou. 5) bpf.h header dependency cleanup, from Jakub. 6) get_func_[arg|ret|arg_cnt] helpers, from Jiri. 7) Sleepable local storage, from KP. 8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-30ethtool: Remove redundant ret assignmentsluo penghao1-1/+0
The assignment here will be overwritten, so it should be deleted The clang_analyzer complains as follows: net/ethtool/netlink.c: Value stored to 'ret' is never read Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: luo penghao <luo.penghao@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-29net: Don't include filter.h from net/sock.hJakub Kicinski1-0/+1
sock.h is pretty heavily used (5k objects rebuilt on x86 after it's touched). We can drop the include of filter.h from it and add a forward declaration of struct sk_filter instead. This decreases the number of rebuilt objects when bpf.h is touched from ~5k to ~1k. There's a lot of missing includes this was masking. Primarily in networking tho, this time. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Acked-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
2021-12-15ethtool: always write dev in ethnl_parse_header_dev_getJakub Kicinski1-3/+2
Commit 0976b888a150 ("ethtool: fix null-ptr-deref on ref tracker") made the write to req_info.dev conditional, but as Eric points out in a different follow up the structure is often allocated on the stack and not kzalloc()'d so seems safer to always write the dev, in case it's garbage on input. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-15ethtool: use ethnl_parse_header_dev_put()Eric Dumazet16-18/+23
It seems I missed that most ethnl_parse_header_dev_get() callers declare an on-stack struct ethnl_req_info, and that they simply call dev_put(req_info.dev) when about to return. Add ethnl_parse_header_dev_put() helper to properly untrack reference taken by ethnl_parse_header_dev_get(). Fixes: e4b8954074f6 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-14ethtool: fix null-ptr-deref on ref trackerJakub Kicinski1-2/+4
dev can be a NULL here, not all requests set require_dev. Fixes: e4b8954074f6 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+2
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-08netlink: add net device refcount tracker to struct ethnl_req_infoEric Dumazet2-3/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-07ethtool: do not perform operations on net devices being unregisteredAntoine Tenart1-1/+2
There is a short period between a net device starts to be unregistered and when it is actually gone. In that time frame ethtool operations could still be performed, which might end up in unwanted or undefined behaviours[1]. Do not allow ethtool operations after a net device starts its unregistration. This patch targets the netlink part as the ioctl one isn't affected: the reference to the net device is taken and the operation is executed within an rtnl lock section and the net device won't be found after unregister. [1] For example adding Tx queues after unregister ends up in NULL pointer exceptions and UaFs, such as: BUG: KASAN: use-after-free in kobject_get+0x14/0x90 Read of size 1 at addr ffff88801961248c by task ethtool/755 CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014 Call Trace: dump_stack_lvl+0x57/0x72 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b kobject_get+0x14/0x90 kobject_add_internal+0x3d1/0x450 kobject_init_and_add+0xba/0xf0 netdev_queue_update_kobjects+0xcf/0x200 netif_set_real_num_tx_queues+0xb4/0x310 veth_set_channels+0x1c3/0x550 ethnl_set_channels+0x524/0x610 Fixes: 041b1c5d4a53 ("ethtool: helper functions for netlink interface") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-07net: add net device refcount tracker to ethtool_phys_id()Eric Dumazet1-2/+3
This helper might hold a netdev reference for a long time, lets add reference tracking. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-30ethtool: netlink: Slightly simplify 'ethnl_features_to_bitmap()'Christophe JAILLET1-1/+0
The 'dest' bitmap is fully initialized by the 'for' loop, so there is no need to explicitly reset it. This also makes this function in line with 'ethnl_features_to_bitmap32()' which does not clear the destination before writing it. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/17fca158231c6f03689bd891254f0dd1f4e84cb8.1638091829.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-27net: ethtool: set a default driver nameTonghao Zhang1-0/+3
The netdev (e.g. ifb, bareudp), which not support ethtool ops (e.g. .get_drvinfo), we can use the rtnl kind as a default name. ifb netdev may be created by others prefix, not ifbX. Cc: Arnd Bergmann <arnd@arndb.de> Cc: Hao Chen <chenhao288@hisilicon.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: Danielle Ratson <danieller@nvidia.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20211125163049.84970-1-xiangxia.m.yue@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+1
drivers/net/ipa/ipa_main.c 8afc7e471ad3 ("net: ipa: separate disabling setup from modem stop") 76b5fbcd6b47 ("net: ipa: kill ipa_modem_init()") Duplicated include, drop one. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()Julian Wiedmann1-1/+1
ethtool_set_coalesce() now uses both the .get_coalesce() and .set_coalesce() callbacks. But the check for their availability is buggy, so changing the coalesce settings on a device where the driver provides only _one_ of the callbacks results in a NULL pointer dereference instead of an -EOPNOTSUPP. Fix the condition so that the availability of both callbacks is ensured. This also matches the netlink code. Note that reproducing this requires some effort - it only affects the legacy ioctl path, and needs a specific combination of driver options: - have .get_coalesce() and .coalesce_supported but no .set_coalesce(), or - have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't cause the crash as it first attempts to call ethtool_get_coalesce() and bails out on error. Fixes: f3ccfda19319 ("ethtool: extend coalesce setting uAPI with CQE mode") Cc: Yufeng Mo <moyufeng@huawei.com> Cc: Huazhong Tan <tanhuazhong@huawei.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-22ethtool: extend ringparam setting/getting API with rx_buf_lenHao Chen2-6/+13
Add two new parameters kernel_ringparam and extack for .get_ringparam and .set_ringparam to extend more ring params through netlink. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: add support to set/get rx buf len via ethtoolHao Chen2-3/+22
Add support to set rx buf len via ethtool -G parameter and get rx buf len via ethtool -g parameter. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: add support to set/get tx copybreak buf size via ethtoolHao Chen2-0/+2
Add support for ethtool to set/get tx copybreak buf size. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-19ethtool: stats: Use struct_group() to clear all stats at onceKees Cook1-8/+7
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memset(), avoid intentionally writing across neighboring fields. Add struct_group() to mark region of struct stats_reply_data that should be initialized, which can now be done in a single memset() call. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-03ethtool: fix ethtool msg len calculation for pause statsJakub Kicinski1-2/+1
ETHTOOL_A_PAUSE_STAT_MAX is the MAX attribute id, so we need to subtract non-stats and add one to get a count (IOW -2+1 == -1). Otherwise we'll see: ethnl cmd 21: calculated reply length 40, but consumed 52 Fixes: 9a27a33027f2 ("ethtool: add standard pause stats") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01ethtool: don't drop the rtnl_lock half way thru the ioctlJakub Kicinski1-4/+32
devlink compat code needs to drop rtnl_lock to take devlink->lock to ensure correct lock ordering. This is problematic because we're not strictly guaranteed that the netdev will not disappear after we re-lock. It may open a possibility of nested ->begin / ->complete calls. Instead of calling into devlink under rtnl_lock take a ref on the devlink instance and make the call after we've dropped rtnl_lock. We (continue to) assume that netdevs have an implicit reference on the devlink returned from ndo_get_devlink_port Note that ndo_get_devlink_port will now get called under rtnl_lock. That should be fine since none of the drivers seem to be taking serious locks inside ndo_get_devlink_port. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01ethtool: handle info/flash data copying outside rtnl_lockJakub Kicinski1-41/+69
We need to increase the lifetime of the data for .get_info and .flash_update beyond their handlers inside rtnl_lock. Allocate a union on the heap and use it instead. Note that we now copy the ethcmd before we lookup dev, hopefully there is no crazy user space depending on error codes. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01ethtool: push the rtnl_lock into dev_ethtool()Jakub Kicinski1-1/+13
Don't take the lock in net/core/dev_ioctl.c, we'll have things to do outside rtnl_lock soon. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-24net: convert users of bitmap_foo() to linkmode_foo()Sean Anderson1-4/+3
This converts instances of bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS) to linkmode_foo(args...) I manually fixed up some lines to prevent them from being excessively long. Otherwise, this change was generated with the following semantic patch: // Generated with // echo linux/linkmode.h > includes // git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \ // | sort | uniq | tee new_includes | wc -l && mv new_includes includes // and repeating until the number stopped going up @i@ @@ ( #include <linux/acpi_mdio.h> | #include <linux/brcmphy.h> | #include <linux/dsa/loop.h> | #include <linux/dsa/sja1105.h> | #include <linux/ethtool.h> | #include <linux/ethtool_netlink.h> | #include <linux/fec.h> | #include <linux/fs_enet_pd.h> | #include <linux/fsl/enetc_mdio.h> | #include <linux/fwnode_mdio.h> | #include <linux/linkmode.h> | #include <linux/lsm_audit.h> | #include <linux/mdio-bitbang.h> | #include <linux/mdio.h> | #include <linux/mdio-mux.h> | #include <linux/mii.h> | #include <linux/mii_timestamper.h> | #include <linux/mlx5/accel.h> | #include <linux/mlx5/cq.h> | #include <linux/mlx5/device.h> | #include <linux/mlx5/driver.h> | #include <linux/mlx5/eswitch.h> | #include <linux/mlx5/fs.h> | #include <linux/mlx5/port.h> | #include <linux/mlx5/qp.h> | #include <linux/mlx5/rsc_dump.h> | #include <linux/mlx5/transobj.h> | #include <linux/mlx5/vport.h> | #include <linux/of_mdio.h> | #include <linux/of_net.h> | #include <linux/pcs-lynx.h> | #include <linux/pcs/pcs-xpcs.h> | #include <linux/phy.h> | #include <linux/phy_led_triggers.h> | #include <linux/phylink.h> | #include <linux/platform_data/bcmgenet.h> | #include <linux/platform_data/xilinx-ll-temac.h> | #include <linux/pxa168_eth.h> | #include <linux/qed/qed_eth_if.h> | #include <linux/qed/qed_fcoe_if.h> | #include <linux/qed/qed_if.h> | #include <linux/qed/qed_iov_if.h> | #include <linux/qed/qed_iscsi_if.h> | #include <linux/qed/qed_ll2_if.h> | #include <linux/qed/qed_nvmetcp_if.h> | #include <linux/qed/qed_rdma_if.h> | #include <linux/sfp.h> | #include <linux/sh_eth.h> | #include <linux/smsc911x.h> | #include <linux/soc/nxp/lpc32xx-misc.h> | #include <linux/stmmac.h> | #include <linux/sunrpc/svc_rdma.h> | #include <linux/sxgbe_platform.h> | #include <net/cfg80211.h> | #include <net/dsa.h> | #include <net/mac80211.h> | #include <net/selftests.h> | #include <rdma/ib_addr.h> | #include <rdma/ib_cache.h> | #include <rdma/ib_cm.h> | #include <rdma/ib_hdrs.h> | #include <rdma/ib_mad.h> | #include <rdma/ib_marshall.h> | #include <rdma/ib_pack.h> | #include <rdma/ib_pma.h> | #include <rdma/ib_sa.h> | #include <rdma/ib_smi.h> | #include <rdma/ib_umem.h> | #include <rdma/ib_umem_odp.h> | #include <rdma/ib_verbs.h> | #include <rdma/iw_cm.h> | #include <rdma/mr_pool.h> | #include <rdma/opa_addr.h> | #include <rdma/opa_port_info.h> | #include <rdma/opa_smi.h> | #include <rdma/opa_vnic.h> | #include <rdma/rdma_cm.h> | #include <rdma/rdma_cm_ib.h> | #include <rdma/rdmavt_cq.h> | #include <rdma/rdma_vt.h> | #include <rdma/rdmavt_qp.h> | #include <rdma/rw.h> | #include <rdma/tid_rdma_defs.h> | #include <rdma/uverbs_ioctl.h> | #include <rdma/uverbs_named_ioctl.h> | #include <rdma/uverbs_std_types.h> | #include <rdma/uverbs_types.h> | #include <soc/mscc/ocelot.h> | #include <soc/mscc/ocelot_ptp.h> | #include <soc/mscc/ocelot_vcap.h> | #include <trace/events/ib_mad.h> | #include <trace/events/rdma_core.h> | #include <trace/events/rdma.h> | #include <trace/events/rpcrdma.h> | #include <uapi/linux/ethtool.h> | #include <uapi/linux/ethtool_netlink.h> | #include <uapi/linux/mdio.h> | #include <uapi/linux/mii.h> ) @depends on i@ expression list args; @@ ( - bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_zero(args) | - bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_copy(args) | - bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_and(args) | - bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_or(args) | - bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_empty(args) | - bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_andnot(args) | - bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_equal(args) | - bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_intersects(args) | - bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_subset(args) ) Add missing linux/mii.h include to mellanox. -DaveM Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-07ethtool: Add ability to control transceiver modules' power modeIdo Schimmel4-1/+204
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and 'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver modules parameters and retrieve their status. The first parameter to control is the power mode of the module. It is only relevant for paged memory modules, as flat memory modules always operate in low power mode. When a paged memory module is in low power mode, its power consumption is reduced to the minimum, the management interface towards the host is available and the data path is deactivated. User space can choose to put modules that are not currently in use in low power mode and transition them to high power mode before putting the associated ports administratively up. This is useful for user space that favors reduced power consumption and lower temperatures over reduced link up times. In QSFP-DD modules the transition from low power mode to high power mode can take a few seconds and this transition is only expected to get longer with future / more complex modules. User space can control the power mode of the module via the power mode policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible values: * high: Module is always in high power mode. * auto: Module is transitioned by the host to high power mode when the first port using it is put administratively up and to low power mode when the last port using it is put administratively down. The operational power mode of the module is available to user space via the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not reported to user space when a module is not plugged-in. The user API is designed to be generic enough so that it could be used for modules with different memory maps (e.g., SFF-8636, CMIS). The only implementation of the device driver API in this series is for a MAC driver (mlxsw) where the module is controlled by the device's firmware, but it is designed to be generic enough so that it could also be used by implementations where the module is controlled by the CPU. CMIS testing ============ # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off The module is not in low power mode, as it is not forced by hardware (LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off). The power mode can be queried from the kernel. In case LowPwrAllowRequestHW was on, the kernel would need to take into account the state of the LowPwrRequestHW signal, which is not visible to user space. $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp11 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp11 up Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp11 down Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On SFF-8636 testing ================ # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm The module is not in low power mode, as it is not forced by hardware (Power override is on) or by software (Power set is off). The power mode can be queried from the kernel. In case Power override was off, the kernel would need to take into account the state of the LPMode signal, which is not visible to user space. $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp13 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp13 up Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp13 down Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-09-29ethtool: ioctl: Use array_size() helper in copy_{from,to}_user()Gustavo A. R. Silva1-5/+7
Use array_size() helper instead of the open-coded version in copy_{from,to}_user(). These sorts of multiplication factors need to be wrapped in array_size(). Link: https://github.com/KSPP/linux/issues/160 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-14ethtool: prevent endless loop if eeprom size is smaller than announcedHeiner Kallweit1-0/+4
It shouldn't happen, but can happen that readable eeprom size is smaller than announced. Then we would be stuck in an endless loop here because after reaching the actual end reads return eeprom.len = 0. I faced this issue when making a mistake in driver development. Detect this scenario and return an error. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-24ethtool: extend coalesce setting uAPI with CQE modeYufeng Mo2-6/+19
In order to support more coalesce parameters through netlink, add two new parameter kernel_coal and extack for .set_coalesce and .get_coalesce, then some extra info can return to user with the netlink API. Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-24ethtool: add two coalesce attributes for CQE modeYufeng Mo2-3/+18
Currently, there are many drivers who support CQE mode configuration, some configure it as a fixed when initialized, some provide an interface to change it by ethtool private flags. In order to make it more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and 'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these parameters can be accessed by ethtool netlink coalesce uAPI. Also add an new structure kernel_ethtool_coalesce, then the new parameter can be added into this struct. Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-06ethtool: return error from ethnl_ops_begin if dev is NULLHeiner Kallweit1-2/+2
Julian reported that after d43c65b05b84 Coverity complains about a missing check whether dev is NULL in ethnl_ops_complete(). There doesn't seem to be any valid case where dev could be NULL when calling ethnl_ops_begin(), therefore return an error if dev is NULL. Fixes: d43c65b05b84 ("ethtool: runtime-resume netdev parent in ethnl_ops_begin") Reported-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-05net: Remove redundant if statementsYajun Deng1-4/+2
The 'if (dev)' statement already move into dev_{put , hold}, so remove redundant if statements. Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03ethtool: runtime-resume netdev parent in ethnl_ops_beginHeiner Kallweit1-6/+25
If a network device is runtime-suspended then: - network device may be flagged as detached and all ethtool ops (even if not accessing the device) will fail because netif_device_present() returns false - ethtool ops may fail because device is not accessible (e.g. because being in D3 in case of a PCI device) It may not be desirable that userspace can't use even simple ethtool ops that not access the device if interface or link is down. To be more friendly to userspace let's ensure that device is runtime-resumed when executing the respective ethtool op in kernel. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>