summaryrefslogtreecommitdiff
path: root/net/ethtool
AgeCommit message (Collapse)AuthorFilesLines
2022-02-24ethtool: add support to set/get completion queue event sizeSubbaraya Sundeep2-3/+18
Add support to set completion queue event size via ethtool -G parameter and get it via ethtool -g parameter. ~ # ./ethtool -G eth0 cqe-size 512 ~ # ./ethtool -g eth0 Ring parameters for eth0: Pre-set maximums: RX: 1048576 RX Mini: n/a RX Jumbo: n/a TX: 1048576 Current hardware settings: RX: 256 RX Mini: n/a RX Jumbo: n/a TX: 4096 RX Buf Len: 2048 CQE Size: 128 Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Signed-off-by: Sunil Goutham <sgoutham@marvell.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-28ethtool: add header/data split indicationJakub Kicinski1-5/+10
For applications running on a mix of platforms it's useful to have a clear indication whether host's NIC supports the geometry requirements of TCP zero-copy. TCP zero-copy Rx requires data to be neatly placed into memory pages. Most NICs can't do that. This patch is adding GET support only, since the NICs I work with either always have the feature enabled or enable it whenever MTU is set to jumbo. In other words I don't need SET. But adding set should be trivial. (The only note on SET is that we will likely want the setting to be "sticky" and use 0 / `unknown` to reset it back to driver default.) Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-06ethtool: use phydev variableTom Rix1-4/+4
In ethtool_get_phy_stats(), the phydev varaible is set to dev->phydev but dev->phydev is still used. Replace dev->phydev uses with phydev. Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-05netlink: do not allocate a device refcount tracker in ethnl_default_notify()Eric Dumazet1-1/+0
As reported by Johannes, the tracker allocated in ethnl_default_notify() is not really needed, as this function is not expected to change a device reference count. Fixes: e4b8954074f6 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Johannes Berg <johannes@sipsolutions.net> Tested-by: Johannes Berg <johannes@sipsolutions.net> Link: https://lore.kernel.org/r/20220105170849.2610470-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller1-0/+1
Alexei Starovoitov says: ==================== pull-request: bpf-next 2021-12-30 The following pull-request contains BPF updates for your *net-next* tree. We've added 72 non-merge commits during the last 20 day(s) which contain a total of 223 files changed, 3510 insertions(+), 1591 deletions(-). The main changes are: 1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii. 2) Beautify and de-verbose verifier logs, from Christy. 3) Composable verifier types, from Hao. 4) bpf_strncmp helper, from Hou. 5) bpf.h header dependency cleanup, from Jakub. 6) get_func_[arg|ret|arg_cnt] helpers, from Jiri. 7) Sleepable local storage, from KP. 8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-30ethtool: Remove redundant ret assignmentsluo penghao1-1/+0
The assignment here will be overwritten, so it should be deleted The clang_analyzer complains as follows: net/ethtool/netlink.c: Value stored to 'ret' is never read Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: luo penghao <luo.penghao@zte.com.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-29net: Don't include filter.h from net/sock.hJakub Kicinski1-0/+1
sock.h is pretty heavily used (5k objects rebuilt on x86 after it's touched). We can drop the include of filter.h from it and add a forward declaration of struct sk_filter instead. This decreases the number of rebuilt objects when bpf.h is touched from ~5k to ~1k. There's a lot of missing includes this was masking. Primarily in networking tho, this time. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Acked-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
2021-12-15ethtool: always write dev in ethnl_parse_header_dev_getJakub Kicinski1-3/+2
Commit 0976b888a150 ("ethtool: fix null-ptr-deref on ref tracker") made the write to req_info.dev conditional, but as Eric points out in a different follow up the structure is often allocated on the stack and not kzalloc()'d so seems safer to always write the dev, in case it's garbage on input. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-15ethtool: use ethnl_parse_header_dev_put()Eric Dumazet16-18/+23
It seems I missed that most ethnl_parse_header_dev_get() callers declare an on-stack struct ethnl_req_info, and that they simply call dev_put(req_info.dev) when about to return. Add ethnl_parse_header_dev_put() helper to properly untrack reference taken by ethnl_parse_header_dev_get(). Fixes: e4b8954074f6 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-14ethtool: fix null-ptr-deref on ref trackerJakub Kicinski1-2/+4
dev can be a NULL here, not all requests set require_dev. Fixes: e4b8954074f6 ("netlink: add net device refcount tracker to struct ethnl_req_info") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-10Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+2
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-08netlink: add net device refcount tracker to struct ethnl_req_infoEric Dumazet2-3/+7
Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-07ethtool: do not perform operations on net devices being unregisteredAntoine Tenart1-1/+2
There is a short period between a net device starts to be unregistered and when it is actually gone. In that time frame ethtool operations could still be performed, which might end up in unwanted or undefined behaviours[1]. Do not allow ethtool operations after a net device starts its unregistration. This patch targets the netlink part as the ioctl one isn't affected: the reference to the net device is taken and the operation is executed within an rtnl lock section and the net device won't be found after unregister. [1] For example adding Tx queues after unregister ends up in NULL pointer exceptions and UaFs, such as: BUG: KASAN: use-after-free in kobject_get+0x14/0x90 Read of size 1 at addr ffff88801961248c by task ethtool/755 CPU: 0 PID: 755 Comm: ethtool Not tainted 5.15.0-rc6+ #778 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-4.fc34 04/014 Call Trace: dump_stack_lvl+0x57/0x72 print_address_description.constprop.0+0x1f/0x140 kasan_report.cold+0x7f/0x11b kobject_get+0x14/0x90 kobject_add_internal+0x3d1/0x450 kobject_init_and_add+0xba/0xf0 netdev_queue_update_kobjects+0xcf/0x200 netif_set_real_num_tx_queues+0xb4/0x310 veth_set_channels+0x1c3/0x550 ethnl_set_channels+0x524/0x610 Fixes: 041b1c5d4a53 ("ethtool: helper functions for netlink interface") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/20211203101318.435618-1-atenart@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-12-07net: add net device refcount tracker to ethtool_phys_id()Eric Dumazet1-2/+3
This helper might hold a netdev reference for a long time, lets add reference tracking. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-30ethtool: netlink: Slightly simplify 'ethnl_features_to_bitmap()'Christophe JAILLET1-1/+0
The 'dest' bitmap is fully initialized by the 'for' loop, so there is no need to explicitly reset it. This also makes this function in line with 'ethnl_features_to_bitmap32()' which does not clear the destination before writing it. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/17fca158231c6f03689bd891254f0dd1f4e84cb8.1638091829.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-27net: ethtool: set a default driver nameTonghao Zhang1-0/+3
The netdev (e.g. ifb, bareudp), which not support ethtool ops (e.g. .get_drvinfo), we can use the rtnl kind as a default name. ifb netdev may be created by others prefix, not ifbX. Cc: Arnd Bergmann <arnd@arndb.de> Cc: Hao Chen <chenhao288@hisilicon.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org> Cc: Danielle Ratson <danieller@nvidia.com> Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20211125163049.84970-1-xiangxia.m.yue@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-27Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-1/+1
drivers/net/ipa/ipa_main.c 8afc7e471ad3 ("net: ipa: separate disabling setup from modem stop") 76b5fbcd6b47 ("net: ipa: kill ipa_modem_init()") Duplicated include, drop one. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-26ethtool: ioctl: fix potential NULL deref in ethtool_set_coalesce()Julian Wiedmann1-1/+1
ethtool_set_coalesce() now uses both the .get_coalesce() and .set_coalesce() callbacks. But the check for their availability is buggy, so changing the coalesce settings on a device where the driver provides only _one_ of the callbacks results in a NULL pointer dereference instead of an -EOPNOTSUPP. Fix the condition so that the availability of both callbacks is ensured. This also matches the netlink code. Note that reproducing this requires some effort - it only affects the legacy ioctl path, and needs a specific combination of driver options: - have .get_coalesce() and .coalesce_supported but no .set_coalesce(), or - have .set_coalesce() but no .get_coalesce(). Here eg. ethtool doesn't cause the crash as it first attempts to call ethtool_get_coalesce() and bails out on error. Fixes: f3ccfda19319 ("ethtool: extend coalesce setting uAPI with CQE mode") Cc: Yufeng Mo <moyufeng@huawei.com> Cc: Huazhong Tan <tanhuazhong@huawei.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Link: https://lore.kernel.org/r/20211126175543.28000-1-jwi@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-11-22ethtool: extend ringparam setting/getting API with rx_buf_lenHao Chen2-6/+13
Add two new parameters kernel_ringparam and extack for .get_ringparam and .set_ringparam to extend more ring params through netlink. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: add support to set/get rx buf len via ethtoolHao Chen2-3/+22
Add support to set rx buf len via ethtool -G parameter and get rx buf len via ethtool -g parameter. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-22ethtool: add support to set/get tx copybreak buf size via ethtoolHao Chen2-0/+2
Add support for ethtool to set/get tx copybreak buf size. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-19ethtool: stats: Use struct_group() to clear all stats at onceKees Cook1-8/+7
In preparation for FORTIFY_SOURCE performing compile-time and run-time field bounds checking for memset(), avoid intentionally writing across neighboring fields. Add struct_group() to mark region of struct stats_reply_data that should be initialized, which can now be done in a single memset() call. Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-03ethtool: fix ethtool msg len calculation for pause statsJakub Kicinski1-2/+1
ETHTOOL_A_PAUSE_STAT_MAX is the MAX attribute id, so we need to subtract non-stats and add one to get a count (IOW -2+1 == -1). Otherwise we'll see: ethnl cmd 21: calculated reply length 40, but consumed 52 Fixes: 9a27a33027f2 ("ethtool: add standard pause stats") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01ethtool: don't drop the rtnl_lock half way thru the ioctlJakub Kicinski1-4/+32
devlink compat code needs to drop rtnl_lock to take devlink->lock to ensure correct lock ordering. This is problematic because we're not strictly guaranteed that the netdev will not disappear after we re-lock. It may open a possibility of nested ->begin / ->complete calls. Instead of calling into devlink under rtnl_lock take a ref on the devlink instance and make the call after we've dropped rtnl_lock. We (continue to) assume that netdevs have an implicit reference on the devlink returned from ndo_get_devlink_port Note that ndo_get_devlink_port will now get called under rtnl_lock. That should be fine since none of the drivers seem to be taking serious locks inside ndo_get_devlink_port. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01ethtool: handle info/flash data copying outside rtnl_lockJakub Kicinski1-41/+69
We need to increase the lifetime of the data for .get_info and .flash_update beyond their handlers inside rtnl_lock. Allocate a union on the heap and use it instead. Note that we now copy the ethcmd before we lookup dev, hopefully there is no crazy user space depending on error codes. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-01ethtool: push the rtnl_lock into dev_ethtool()Jakub Kicinski1-1/+13
Don't take the lock in net/core/dev_ioctl.c, we'll have things to do outside rtnl_lock soon. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-24net: convert users of bitmap_foo() to linkmode_foo()Sean Anderson1-4/+3
This converts instances of bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS) to linkmode_foo(args...) I manually fixed up some lines to prevent them from being excessively long. Otherwise, this change was generated with the following semantic patch: // Generated with // echo linux/linkmode.h > includes // git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \ // | sort | uniq | tee new_includes | wc -l && mv new_includes includes // and repeating until the number stopped going up @i@ @@ ( #include <linux/acpi_mdio.h> | #include <linux/brcmphy.h> | #include <linux/dsa/loop.h> | #include <linux/dsa/sja1105.h> | #include <linux/ethtool.h> | #include <linux/ethtool_netlink.h> | #include <linux/fec.h> | #include <linux/fs_enet_pd.h> | #include <linux/fsl/enetc_mdio.h> | #include <linux/fwnode_mdio.h> | #include <linux/linkmode.h> | #include <linux/lsm_audit.h> | #include <linux/mdio-bitbang.h> | #include <linux/mdio.h> | #include <linux/mdio-mux.h> | #include <linux/mii.h> | #include <linux/mii_timestamper.h> | #include <linux/mlx5/accel.h> | #include <linux/mlx5/cq.h> | #include <linux/mlx5/device.h> | #include <linux/mlx5/driver.h> | #include <linux/mlx5/eswitch.h> | #include <linux/mlx5/fs.h> | #include <linux/mlx5/port.h> | #include <linux/mlx5/qp.h> | #include <linux/mlx5/rsc_dump.h> | #include <linux/mlx5/transobj.h> | #include <linux/mlx5/vport.h> | #include <linux/of_mdio.h> | #include <linux/of_net.h> | #include <linux/pcs-lynx.h> | #include <linux/pcs/pcs-xpcs.h> | #include <linux/phy.h> | #include <linux/phy_led_triggers.h> | #include <linux/phylink.h> | #include <linux/platform_data/bcmgenet.h> | #include <linux/platform_data/xilinx-ll-temac.h> | #include <linux/pxa168_eth.h> | #include <linux/qed/qed_eth_if.h> | #include <linux/qed/qed_fcoe_if.h> | #include <linux/qed/qed_if.h> | #include <linux/qed/qed_iov_if.h> | #include <linux/qed/qed_iscsi_if.h> | #include <linux/qed/qed_ll2_if.h> | #include <linux/qed/qed_nvmetcp_if.h> | #include <linux/qed/qed_rdma_if.h> | #include <linux/sfp.h> | #include <linux/sh_eth.h> | #include <linux/smsc911x.h> | #include <linux/soc/nxp/lpc32xx-misc.h> | #include <linux/stmmac.h> | #include <linux/sunrpc/svc_rdma.h> | #include <linux/sxgbe_platform.h> | #include <net/cfg80211.h> | #include <net/dsa.h> | #include <net/mac80211.h> | #include <net/selftests.h> | #include <rdma/ib_addr.h> | #include <rdma/ib_cache.h> | #include <rdma/ib_cm.h> | #include <rdma/ib_hdrs.h> | #include <rdma/ib_mad.h> | #include <rdma/ib_marshall.h> | #include <rdma/ib_pack.h> | #include <rdma/ib_pma.h> | #include <rdma/ib_sa.h> | #include <rdma/ib_smi.h> | #include <rdma/ib_umem.h> | #include <rdma/ib_umem_odp.h> | #include <rdma/ib_verbs.h> | #include <rdma/iw_cm.h> | #include <rdma/mr_pool.h> | #include <rdma/opa_addr.h> | #include <rdma/opa_port_info.h> | #include <rdma/opa_smi.h> | #include <rdma/opa_vnic.h> | #include <rdma/rdma_cm.h> | #include <rdma/rdma_cm_ib.h> | #include <rdma/rdmavt_cq.h> | #include <rdma/rdma_vt.h> | #include <rdma/rdmavt_qp.h> | #include <rdma/rw.h> | #include <rdma/tid_rdma_defs.h> | #include <rdma/uverbs_ioctl.h> | #include <rdma/uverbs_named_ioctl.h> | #include <rdma/uverbs_std_types.h> | #include <rdma/uverbs_types.h> | #include <soc/mscc/ocelot.h> | #include <soc/mscc/ocelot_ptp.h> | #include <soc/mscc/ocelot_vcap.h> | #include <trace/events/ib_mad.h> | #include <trace/events/rdma_core.h> | #include <trace/events/rdma.h> | #include <trace/events/rpcrdma.h> | #include <uapi/linux/ethtool.h> | #include <uapi/linux/ethtool_netlink.h> | #include <uapi/linux/mdio.h> | #include <uapi/linux/mii.h> ) @depends on i@ expression list args; @@ ( - bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_zero(args) | - bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_copy(args) | - bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_and(args) | - bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_or(args) | - bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_empty(args) | - bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_andnot(args) | - bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_equal(args) | - bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_intersects(args) | - bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_subset(args) ) Add missing linux/mii.h include to mellanox. -DaveM Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-07ethtool: Add ability to control transceiver modules' power modeIdo Schimmel4-1/+204
Add a pair of new ethtool messages, 'ETHTOOL_MSG_MODULE_SET' and 'ETHTOOL_MSG_MODULE_GET', that can be used to control transceiver modules parameters and retrieve their status. The first parameter to control is the power mode of the module. It is only relevant for paged memory modules, as flat memory modules always operate in low power mode. When a paged memory module is in low power mode, its power consumption is reduced to the minimum, the management interface towards the host is available and the data path is deactivated. User space can choose to put modules that are not currently in use in low power mode and transition them to high power mode before putting the associated ports administratively up. This is useful for user space that favors reduced power consumption and lower temperatures over reduced link up times. In QSFP-DD modules the transition from low power mode to high power mode can take a few seconds and this transition is only expected to get longer with future / more complex modules. User space can control the power mode of the module via the power mode policy attribute ('ETHTOOL_A_MODULE_POWER_MODE_POLICY'). Possible values: * high: Module is always in high power mode. * auto: Module is transitioned by the host to high power mode when the first port using it is put administratively up and to low power mode when the last port using it is put administratively down. The operational power mode of the module is available to user space via the 'ETHTOOL_A_MODULE_POWER_MODE' attribute. The attribute is not reported to user space when a module is not plugged-in. The user API is designed to be generic enough so that it could be used for modules with different memory maps (e.g., SFF-8636, CMIS). The only implementation of the device driver API in this series is for a MAC driver (mlxsw) where the module is controlled by the device's firmware, but it is designed to be generic enough so that it could also be used by implementations where the module is controlled by the CPU. CMIS testing ============ # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off The module is not in low power mode, as it is not forced by hardware (LowPwrAllowRequestHW is off) or by software (LowPwrRequestSW is off). The power mode can be queried from the kernel. In case LowPwrAllowRequestHW was on, the kernel would need to take into account the state of the LowPwrRequestHW signal, which is not visible to user space. $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp11 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp11 up Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x03 (ModuleReady) LowPwrAllowRequestHW : Off LowPwrRequestSW : Off Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp11 down Query the power mode again: $ ethtool --show-module swp11 Module parameters for swp11: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp11 Identifier : 0x18 (QSFP-DD Double Density 8X Pluggable Transceiver (INF-8628)) ... Module State : 0x01 (ModuleLowPwr) LowPwrAllowRequestHW : Off LowPwrRequestSW : On SFF-8636 testing ================ # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7733 mW / -1.12 dBm Transmit avg optical power (Channel 2) : 0.7649 mW / -1.16 dBm Transmit avg optical power (Channel 3) : 0.7790 mW / -1.08 dBm Transmit avg optical power (Channel 4) : 0.7837 mW / -1.06 dBm Rcvr signal avg optical power(Channel 1) : 0.9302 mW / -0.31 dBm Rcvr signal avg optical power(Channel 2) : 0.9079 mW / -0.42 dBm Rcvr signal avg optical power(Channel 3) : 0.8993 mW / -0.46 dBm Rcvr signal avg optical power(Channel 4) : 0.8778 mW / -0.57 dBm The module is not in low power mode, as it is not forced by hardware (Power override is on) or by software (Power set is off). The power mode can be queried from the kernel. In case Power override was off, the kernel would need to take into account the state of the LPMode signal, which is not visible to user space. $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy high power-mode high Change the power mode policy to 'auto': # ethtool --set-module swp13 power-mode-policy auto Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Put the associated port administratively up which will instruct the host to transition the module to high power mode: # ip link set dev swp13 up Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode high Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) enabled Power set : Off Power override : On ... Transmit avg optical power (Channel 1) : 0.7934 mW / -1.01 dBm Transmit avg optical power (Channel 2) : 0.7859 mW / -1.05 dBm Transmit avg optical power (Channel 3) : 0.7885 mW / -1.03 dBm Transmit avg optical power (Channel 4) : 0.7985 mW / -0.98 dBm Rcvr signal avg optical power(Channel 1) : 0.9325 mW / -0.30 dBm Rcvr signal avg optical power(Channel 2) : 0.9034 mW / -0.44 dBm Rcvr signal avg optical power(Channel 3) : 0.9086 mW / -0.42 dBm Rcvr signal avg optical power(Channel 4) : 0.8885 mW / -0.51 dBm Put the associated port administratively down which will instruct the host to transition the module to low power mode: # ip link set dev swp13 down Query the power mode again: $ ethtool --show-module swp13 Module parameters for swp13: power-mode-policy auto power-mode low Verify with the data read from the EEPROM: # ethtool -m swp13 Identifier : 0x11 (QSFP28) ... Extended identifier description : 5.0W max. Power consumption, High Power Class (> 3.5 W) not enabled Power set : On Power override : On ... Transmit avg optical power (Channel 1) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 2) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 3) : 0.0000 mW / -inf dBm Transmit avg optical power (Channel 4) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 1) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 2) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 3) : 0.0000 mW / -inf dBm Rcvr signal avg optical power(Channel 4) : 0.0000 mW / -inf dBm Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-09-29ethtool: ioctl: Use array_size() helper in copy_{from,to}_user()Gustavo A. R. Silva1-5/+7
Use array_size() helper instead of the open-coded version in copy_{from,to}_user(). These sorts of multiplication factors need to be wrapped in array_size(). Link: https://github.com/KSPP/linux/issues/160 Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-14ethtool: prevent endless loop if eeprom size is smaller than announcedHeiner Kallweit1-0/+4
It shouldn't happen, but can happen that readable eeprom size is smaller than announced. Then we would be stuck in an endless loop here because after reaching the actual end reads return eeprom.len = 0. I faced this issue when making a mistake in driver development. Detect this scenario and return an error. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-24ethtool: extend coalesce setting uAPI with CQE modeYufeng Mo2-6/+19
In order to support more coalesce parameters through netlink, add two new parameter kernel_coal and extack for .set_coalesce and .get_coalesce, then some extra info can return to user with the netlink API. Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-24ethtool: add two coalesce attributes for CQE modeYufeng Mo2-3/+18
Currently, there are many drivers who support CQE mode configuration, some configure it as a fixed when initialized, some provide an interface to change it by ethtool private flags. In order to make it more generic, add two new 'ETHTOOL_A_COALESCE_USE_CQE_TX' and 'ETHTOOL_A_COALESCE_USE_CQE_RX' coalesce attributes, then these parameters can be accessed by ethtool netlink coalesce uAPI. Also add an new structure kernel_ethtool_coalesce, then the new parameter can be added into this struct. Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-08-06ethtool: return error from ethnl_ops_begin if dev is NULLHeiner Kallweit1-2/+2
Julian reported that after d43c65b05b84 Coverity complains about a missing check whether dev is NULL in ethnl_ops_complete(). There doesn't seem to be any valid case where dev could be NULL when calling ethnl_ops_begin(), therefore return an error if dev is NULL. Fixes: d43c65b05b84 ("ethtool: runtime-resume netdev parent in ethnl_ops_begin") Reported-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-05net: Remove redundant if statementsYajun Deng1-4/+2
The 'if (dev)' statement already move into dev_{put , hold}, so remove redundant if statements. Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03ethtool: runtime-resume netdev parent in ethnl_ops_beginHeiner Kallweit1-6/+25
If a network device is runtime-suspended then: - network device may be flagged as detached and all ethtool ops (even if not accessing the device) will fail because netif_device_present() returns false - ethtool ops may fail because device is not accessible (e.g. because being in D3 in case of a PCI device) It may not be desirable that userspace can't use even simple ethtool ops that not access the device if interface or link is down. To be more friendly to userspace let's ensure that device is runtime-resumed when executing the respective ethtool op in kernel. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03ethtool: move netif_device_present check from ethnl_parse_header_dev_get to ↵Heiner Kallweit1-7/+7
ethnl_ops_begin If device is runtime-suspended and not accessible then it may be flagged as not present. If checking whether device is present is done too early then we may bail out before we have the chance to runtime-resume the device. Therefore move this check to ethnl_ops_begin(). This is in preparation of a follow-up patch that tries to runtime-resume the device before executing ethtool ops. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03ethtool: move implementation of ethnl_ops_begin/complete to netlink.cHeiner Kallweit2-13/+16
In preparation of subsequent extensions to both functions move the implementations from netlink.h to netlink.c. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-08-03ethtool: runtime-resume netdev parent before ethtool ioctl opsHeiner Kallweit1-3/+15
If a network device is runtime-suspended then: - network device may be flagged as detached and all ethtool ops (even if not accessing the device) will fail because netif_device_present() returns false - ethtool ops may fail because device is not accessible (e.g. because being in D3 in case of a PCI device) It may not be desirable that userspace can't use even simple ethtool ops that not access the device if interface or link is down. To be more friendly to userspace let's ensure that device is runtime-resumed when executing the respective ethtool op in kernel. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27dev_ioctl: pass SIOCDEVPRIVATE data separatelyArnd Bergmann1-2/+1
The compat handlers for SIOCDEVPRIVATE are incorrect for any driver that passes data as part of struct ifreq rather than as an ifr_data pointer, or that passes data back this way, since the compat_ifr_data_ioctl() helper overwrites the ifr_data pointer and does not copy anything back out. Since all drivers using devprivate commands are now converted to the new .ndo_siocdevprivate callback, fix this by adding the missing piece and passing the pointer separately the whole way. This further unifies the native and compat logic for socket ioctls, as the new code now passes the correct pointer as well as the correct data for both native and compat ioctls. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-27ethtool: Fix rxnfc copy to user buffer overflowSaeed Mahameed1-1/+1
In the cited commit, copy_to_user() got called with the wrong pointer, instead of passing the actual buffer ptr to copy from, a pointer to the pointer got passed, which causes a buffer overflow calltrace to pop up when executing "ethtool -x ethX". Fix ethtool_rxnfc_copy_to_user() to use the rxnfc pointer as passed to the function, instead of a pointer to it. This fixes below call trace: [ 15.533533] ------------[ cut here ]------------ [ 15.539007] Buffer overflow detected (8 < 192)! [ 15.544110] WARNING: CPU: 3 PID: 1801 at include/linux/thread_info.h:200 copy_overflow+0x15/0x20 [ 15.549308] Modules linked in: [ 15.551449] CPU: 3 PID: 1801 Comm: ethtool Not tainted 5.14.0-rc2+ #1058 [ 15.553919] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 [ 15.558378] RIP: 0010:copy_overflow+0x15/0x20 [ 15.560648] Code: e9 7c ff ff ff b8 a1 ff ff ff eb c4 66 0f 1f 84 00 00 00 00 00 55 48 89 f2 89 fe 48 c7 c7 88 55 78 8a 48 89 e5 e8 06 5c 1e 00 <0f> 0b 5d c3 0f 1f 80 00 00 00 00 0f 1f 44 00 00 55 48 89 e5 41 55 [ 15.565114] RSP: 0018:ffffad49c0523bd0 EFLAGS: 00010286 [ 15.566231] RAX: 0000000000000000 RBX: 00000000000000c0 RCX: 0000000000000000 [ 15.567616] RDX: 0000000000000001 RSI: ffffffff8a7912e7 RDI: 00000000ffffffff [ 15.569050] RBP: ffffad49c0523bd0 R08: ffffffff8ab2ae28 R09: 00000000ffffdfff [ 15.570534] R10: ffffffff8aa4ae40 R11: ffffffff8aa4ae40 R12: 0000000000000000 [ 15.571899] R13: 00007ffd4cc2a230 R14: ffffad49c0523c00 R15: 0000000000000000 [ 15.573584] FS: 00007f538112f740(0000) GS:ffff96d5bdd80000(0000) knlGS:0000000000000000 [ 15.575639] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 15.577092] CR2: 00007f5381226d40 CR3: 0000000013542000 CR4: 00000000001506e0 [ 15.578929] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 15.580695] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 15.582441] Call Trace: [ 15.582970] ethtool_rxnfc_copy_to_user+0x30/0x46 [ 15.583815] ethtool_get_rxnfc.cold+0x23/0x2b [ 15.584584] dev_ethtool+0x29c/0x25f0 [ 15.585286] ? security_netlbl_sid_to_secattr+0x77/0xd0 [ 15.586728] ? do_set_pte+0xc4/0x110 [ 15.587349] ? _raw_spin_unlock+0x18/0x30 [ 15.588118] ? __might_sleep+0x49/0x80 [ 15.588956] dev_ioctl+0x2c1/0x490 [ 15.589616] sock_ioctl+0x18e/0x330 [ 15.591143] __x64_sys_ioctl+0x41c/0x990 [ 15.591823] ? irqentry_exit_to_user_mode+0x9/0x20 [ 15.592657] ? irqentry_exit+0x33/0x40 [ 15.593308] ? exc_page_fault+0x32f/0x770 [ 15.593877] ? exit_to_user_mode_prepare+0x3c/0x130 [ 15.594775] do_syscall_64+0x35/0x80 [ 15.595397] entry_SYSCALL_64_after_hwframe+0x44/0xae [ 15.596037] RIP: 0033:0x7f5381226d4b [ 15.596492] Code: 0f 1e fa 48 8b 05 3d b1 0c 00 64 c7 00 26 00 00 00 48 c7 c0 ff ff ff ff c3 66 0f 1f 44 00 00 f3 0f 1e fa b8 10 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 0d b1 0c 00 f7 d8 64 89 01 48 [ 15.598743] RSP: 002b:00007ffd4cc2a1f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010 [ 15.599804] RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f5381226d4b [ 15.600795] RDX: 00007ffd4cc2a350 RSI: 0000000000008946 RDI: 0000000000000003 [ 15.601712] RBP: 00007ffd4cc2a340 R08: 00007ffd4cc2a350 R09: 0000000000000001 [ 15.602751] R10: 00007f538128a990 R11: 0000000000000246 R12: 0000000000000000 [ 15.603882] R13: 00007ffd4cc2a350 R14: 00007ffd4cc2a4b0 R15: 0000000000000000 [ 15.605042] ---[ end trace 325cf185e2795048 ]--- Fixes: dd98d2895de6 ("ethtool: improve compat ioctl handling") Reported-by: Shannon Nelson <snelson@pensando.io> CC: Arnd Bergmann <arnd@arndb.de> CC: Christoph Hellwig <hch@lst.de> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Tested-by: Shannon Nelson <snelson@pensando.io> Acked-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-23ethtool: improve compat ioctl handlingArnd Bergmann1-16/+120
The ethtool compat ioctl handling is hidden away in net/socket.c, which introduces a couple of minor oddities: - The implementation may end up diverging, as seen in the RXNFC extension in commit 84a1d9c48200 ("net: ethtool: extend RXNFC API to support RSS spreading of filter matches") that does not work in compat mode. - Most architectures do not need the compat handling at all because u64 and compat_u64 have the same alignment. - On x86, the conversion is done for both x32 and i386 user space, but it's actually wrong to do it for x32 and cannot work there. - On 32-bit Arm, it never worked for compat oabi user space, since that needs to do the same conversion but does not. - It would be nice to get rid of both compat_alloc_user_space() and copy_in_user() throughout the kernel. None of these actually seems to be a serious problem that real users are likely to encounter, but fixing all of them actually leads to code that is both shorter and more readable. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-01net: sock: extend SO_TIMESTAMPING for PHC bindingYangbo Lu1-0/+1
Since PTP virtual clock support is added, there can be several PTP virtual clocks based on one PTP physical clock for timestamping. This patch is to extend SO_TIMESTAMPING API to support PHC (PTP Hardware Clock) binding by adding a new flag SOF_TIMESTAMPING_BIND_PHC. When PTP virtual clocks are in use, user space can configure to bind one for timestamping, but PTP physical clock is not supported and not needed to bind. This patch is preparation for timestamp conversion from raw timestamp to a specific PTP virtual clock time in core net. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-07-01ethtool: add a new command for getting PHC virtual clocksYangbo Lu5-1/+120
Add an interface for getting PHC (PTP Hardware Clock) virtual clocks, which are based on PHC physical clock providing hardware timestamp to network packets. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22ethtool: Validate module EEPROM offset as part of policyIdo Schimmel1-5/+2
Validate the offset to read from module EEPROM as part of the netlink policy and remove the corresponding check from the code. This also makes it possible to query the offset range from user space: $ genl ctrl policy name ethtool ... ID: 0x14 policy[32]:attr[2]: type=U32 range:[0,255] ... Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22ethtool: Validate module EEPROM length as part of policyIdo Schimmel1-4/+2
Validate the number of bytes to read from the module EEPROM as part of the netlink policy and remove the corresponding check from the code. This also makes it possible to query the length range from user space: $ genl ctrl policy name ethtool ... ID: 0x14 policy[32]:attr[3]: type=U32 range:[1,128] ... Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-22ethtool: Decrease size of module EEPROM get policy arrayIdo Schimmel1-1/+1
The 'ETHTOOL_A_MODULE_EEPROM_DATA' attribute is not part of the get request. Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-19Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski3-6/+8
Trivial conflicts in net/can/isotp.c and tools/testing/selftests/net/mptcp/mptcp_connect.sh scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c to include/linux/ptp_clock_kernel.h in -next so re-apply the fix there. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-06-16ethtool: add a stricter length checkJakub Kicinski1-3/+8
There has been a few errors in the ethtool reply size calculations, most of those are hard to trigger during basic testing because of skb size rounding up and netdev names being shorter than max. Add a more precise check. This change will affect the value of payload length displayed in case of -EMSGSIZE but that should be okay, "payload length" isn't a well defined term here. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-14ethtool: strset: fix message length calculationJakub Kicinski1-0/+2
Outer nest for ETHTOOL_A_STRSET_STRINGSETS is not accounted for. This may result in ETHTOOL_MSG_STRSET_GET producing a warning like: calculated message payload length (684) not sufficient WARNING: CPU: 0 PID: 30967 at net/ethtool/netlink.c:369 ethnl_default_doit+0x87a/0xa20 and a splat. As usually with such warnings three conditions must be met for the warning to trigger: - there must be no skb size rounding up (e.g. reply_size of 684); - string set must be per-device (so that the header gets populated); - the device name must be at least 12 characters long. all in all with current user space it looks like reading priv flags is the only place this could potentially happen. Or with syzbot :) Reported-by: syzbot+59aa77b92d06cd5a54f2@syzkaller.appspotmail.com Fixes: 71921690f974 ("ethtool: provide string sets with STRSET_GET request") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-06-09net: ethtool: clear heap allocations for ethtool functionAustin Kim1-5/+5
Several ethtool functions leave heap uncleared (potentially) by drivers. This will leave the unused portion of heap unchanged and might copy the full contents back to userspace. Signed-off-by: Austin Kim <austindh.kim@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-28 15:01:26 +0300