summaryrefslogtreecommitdiff
path: root/net/mac80211
AgeCommit message (Collapse)AuthorFilesLines
2022-06-01wifi: mac80211: fix use-after-free in chanctx codeJohannes Berg1-5/+2
In ieee80211_vif_use_reserved_context(), when we have an old context and the new context's replace_state is set to IEEE80211_CHANCTX_REPLACE_NONE, we free the old context in ieee80211_vif_use_reserved_reassign(). Therefore, we cannot check the old_ctx anymore, so we should set it to NULL after this point. However, since the new_ctx replace state is clearly not IEEE80211_CHANCTX_REPLACES_OTHER, we're not going to do anything else in this function and can just return to avoid accessing the freed old_ctx. Cc: stable@vger.kernel.org Fixes: 5bcae31d9cb1 ("mac80211: implement multi-vif in-place reservations") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220601091926.df419d91b165.I17a9b3894ff0b8323ce2afdb153b101124c821e5@changeid
2022-05-19Merge tag 'wireless-next-2022-05-19' of ↵Jakub Kicinski13-240/+369
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v5.19 Second set of patches for v5.19 and most likely the last one. rtw89 got support for 8852ce devices and mt76 now supports Wireless Ethernet Dispatch. Major changes: cfg80211/mac80211 - support disabling EHT mode rtw89 - add support for Realtek 8852ce devices mt76 - Wireless Ethernet Dispatch support for flow offload - non-standard VHT MCS10-11 support - mt7921 AP mode support - mt7921 ipv6 NS offload support ath11k - enable keepalive during WoWLAN suspend - implement remain-on-channel support * tag 'wireless-next-2022-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (135 commits) iwlwifi: mei: fix potential NULL-ptr deref iwlwifi: mei: clear the sap data header before sending iwlwifi: mvm: remove vif_count iwlwifi: mvm: always tell the firmware to accept MCAST frames in BSS iwlwifi: mvm: add OTP info in case of init failure iwlwifi: mvm: fix assert 1F04 upon reconfig iwlwifi: fw: init SAR GEO table only if data is present iwlwifi: mvm: clean up authorized condition iwlwifi: mvm: use NULL instead of ERR_PTR when parsing wowlan status iwlwifi: pcie: simplify MSI-X cause mapping rtw89: pci: only mask out INT indicator register for disable interrupt v1 rtw89: convert rtw89_band to nl80211_band precisely rtw89: 8852c: update txpwr tables to HALRF_027_00_052 rtw89: cfo: check mac_id to avoid out-of-bounds rtw89: 8852c: set TX antenna path rtw89: add ieee80211::sta_rc_update ops wireless: Fix Makefile to be in alphabetical order mac80211: refactor freeing the next_beacon cfg80211: fix kernel-doc for cfg80211_beacon_data mac80211: minstrel_ht: support ieee80211_rate_status ... ==================== Link: https://lore.kernel.org/r/20220519153334.8D051C385AA@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-17mac80211: refactor freeing the next_beaconJohannes Berg1-27/+18
We have this code seven times, refactor it into a separate function. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: minstrel_ht: support ieee80211_rate_statusJonas Jelonek2-9/+133
This patch adds support for the new struct ieee80211_rate_status and its annotation in struct ieee80211_tx_status in minstrel_ht. In minstrel_ht_tx_status, a check for the presence of instances of the new struct in ieee80211_tx_status is added. Based on this, minstrel_ht then gets and updates internal rate stats with either struct ieee80211_rate_status or ieee80211_tx_info->status.rates. Adjusted variants of minstrel_ht_txstat_valid, minstrel_ht_get_stats, minstrel_{ht/vht}_get_group_idx are added which use struct ieee80211_rate_status and struct rate_info instead of the legacy structs. struct rate_info from cfg80211.h does not provide whether short preamble was used for the transmission. So we retrieve this information from VIF and STA configuration and cache it in a new flag in struct minstrel_ht_sta per rate control instance. Compile-Tested: current wireless-next tree with all flags on Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt Linux 5.10.113 Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com> Link: https://lore.kernel.org/r/20220509173958.1398201-3-jelonek.jonas@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: extend current rate control tx status APIJonas Jelonek1-39/+52
This patch adds the new struct ieee80211_rate_status and replaces 'struct rate_info *rate' in ieee80211_tx_status with pointer and length annotation. The struct ieee80211_rate_status allows to: (1) receive tx power status feedback for transmit power control (TPC) per packet or packet retry (2) dynamic mapping of wifi chip specific multi-rate retry (mrr) chains with different lengths (3) increase the limit of annotatable rate indices to support IEEE802.11ac rate sets and beyond ieee80211_tx_info, control and status buffer, and ieee80211_tx_rate cannot be used to achieve these goals due to fixed size limitations. Our new struct contains a struct rate_info to annotate the rate that was used, retry count of the rate and tx power. It is intended for all information related to RC and TPC that needs to be passed from driver to mac80211 and its RC/TPC algorithms like Minstrel_HT. It corresponds to one stage in an mrr. Multiple subsequent instances of this struct can be included in struct ieee80211_tx_status via a pointer and a length variable. Those instances can be allocated on-stack. The former reference to a single instance of struct rate_info is replaced with our new annotation. An extension is introduced to struct ieee80211_hw. There are two new members called 'tx_power_levels' and 'max_txpwr_levels_idx' acting as a tx power level table. When a wifi device is registered, the driver shall supply all supported power levels in this list. This allows to support several quirks like differing power steps in power level ranges or alike. TPC can use this for algorithm and thus be designed more abstract instead of handling all possible step widths individually. Further mandatory changes in status.c, mt76 and ath11k drivers due to the removal of 'struct rate_info *rate' are also included. status.c already uses the information in ieee80211_tx_status->rate in radiotap, this is now changed to use ieee80211_rate_status->rate_idx. mt76 driver already uses struct rate_info to pass the tx rate to status path. The new members of the ieee80211_tx_status are set to NULL and 0 because the previously passed rate is not relevant to rate control and accurate information is passed via tx_info->status.rates. For ath11k, the txrate can be passed via this struct because ath11k uses firmware RC and thus the information does not interfere with software RC. Compile-Tested: current wireless-next tree with all flags on Tested-on: Xiaomi 4A Gigabit (MediaTek MT7603E, MT7612E) with OpenWrt Linux 5.10.113 Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com> Link: https://lore.kernel.org/r/20220509173958.1398201-2-jelonek.jonas@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: minstrel_ht: fill all requested ratesPeter Seiderer1-7/+7
Fill all requested rates (in case of ath9k 4 rate slots are available, so fill all 4 instead of only 3), improves throughput in noisy environment. Signed-off-by: Peter Seiderer <ps.report@gmx.net> Link: https://lore.kernel.org/r/20220402153014.31332-2-ps.report@gmx.net Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: disable BSS color collision detection in case of no free colorsLavanya Suresh1-0/+9
AP may run out of BSS color after color collision detection event from driver. Disable BSS color collision detection if no free colors are available based on bss color disabled bit sent as a part of NL80211_ATTR_HE_BSS_COLOR attribute sent in NL80211_CMD_SET_BEACON. It can be reenabled once new color is available. Signed-off-by: Lavanya Suresh <lavaks@codeaurora.org> Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Link: https://lore.kernel.org/r/1649867295-7204-3-git-send-email-quic_ramess@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16nl80211: Parse NL80211_ATTR_HE_BSS_COLOR as a part of nl80211_parse_beaconRameshkumar Sundaram1-2/+2
NL80211_ATTR_HE_BSS_COLOR attribute can be included in both NL80211_CMD_START_AP and NL80211_CMD_SET_BEACON commands. Move he_bss_color from cfg80211_ap_settings to cfg80211_beacon_data and parse NL80211_ATTR_HE_BSS_COLOR as a part of nl80211_parse_beacon() to have bss color settings parsed for both start ap and set beacon commands. Add a new flag he_bss_color_valid to indicate whether NL80211_ATTR_HE_BSS_COLOR attribute is included. Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Link: https://lore.kernel.org/r/1649867295-7204-2-git-send-email-quic_ramess@quicinc.com [fix build ...] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: mlme: track assoc_bss/associated separatelyJohannes Berg2-10/+13
We currently track whether we're associated and which the BSS is in the same variable (ifmgd->associated), but for MLD we'll need to move the BSS pointer to be per link, while the question whether we're associated or not is for the whole interface. Add ifmgd->assoc_bss that stores the pointer and change ifmgd->associated to be just a bool, so the question of whether we're associated can continue working after MLD rework, without requiring changes, while the BSS pointer will have to be changed/used checked per link. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: remove useless bssid copyJohannes Berg1-3/+1
We don't need to copy this locally, we now only use the variable to print before doing other things. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: remove unused argument to ieee80211_sta_connection_lost()Johannes Berg3-9/+7
We never use the bssid argument to ieee80211_sta_connection_lost() so we might as well just remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: mlme: use local SSID copyJohannes Berg1-12/+2
There's no need to look it up from the ifmgd->associated BSS configuration, we already maintain a local copy since commit b0140fda626e ("mac80211: mlme: save ssid info to ieee80211_bss_conf while assoc"). Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: use ifmgd->bssid instead of ifmgd->associated->bssidJohannes Berg5-21/+21
Since we always track the BSSID there when we get associated, these are equivalent, but ifmgd->bssid saves a dereference and thus makes the code a bit smaller, and more readable. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: mlme: move in RSSI reporting codeJohannes Berg2-40/+40
This code is tightly coupled to the sdata->u.mgd data structure, so there's no reason for it to be in utils. Move it to mlme.c. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-16mac80211: unify CCMP/GCMP AAD constructionJohannes Berg1-56/+31
Ping-Ke's previous patch adjusted the CCMP AAD construction to properly take the order bit into account, but failed to update the (identical) GCMP AAD construction as well. Unify the AAD construction between the two cases. Reported-by: Jouni Malinen <j@w1.fi> Link: https://lore.kernel.org/r/20220506105150.51d66e2a6f3c.I65f12be82c112365169e8a9f48c7a71300e814b9@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-13Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski2-2/+7
No conflicts. Build issue in drivers/net/ethernet/sfc/ptp.c 54fccfdd7c66 ("sfc: efx_default_channel_type APIs can be static") 49e6123c65da ("net: sfc: fix memory leak due to ptp channel") https://lore.kernel.org/all/20220510130556.52598fe2@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-04mac80211: support disabling EHT modeMuna Sinada1-0/+3
Allow userspace to disable EHT mode. This forces EHT capable interfaces to disable during association. Signed-off-by: Muna Sinada <quic_msinada@quicinc.com> Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com> Link: https://lore.kernel.org/r/20220323224636.20211-2-quic_alokad@quicinc.com [remove stray message change] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-04mac80211: upgrade passive scan to active scan on DFS channels after beacon rxFelix Fietkau2-0/+25
In client mode, we can't connect to hidden SSID APs or SSIDs not advertised in beacons on DFS channels, since we're forced to passive scan. Fix this by sending out a probe request immediately after the first beacon, if active scan was requested by the user. Cc: stable@vger.kernel.org Reported-by: Catrinel Catrinescu <cc@80211.de> Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20220420104907.36275-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-04mac80211: tx: delete a redundant if statement in ieee80211_check_fast_xmit()Hangyu Hua1-2/+0
If statement is meaningless because the code will goto out regardless of whether fast_tx is NULL or not. Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Link: https://lore.kernel.org/r/20220413091902.27438-1-hbh25y@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-04mac80211: consider Order bit to fill CCMP AADPing-Ke Shih1-7/+9
Follow IEEE 802.11-21 that HTC subfield masked to 0 for all data frames containing a QoS Control field. It also defines the AAD length depends on QC and A4 fields, so change logic to determine length accordingly. Signed-off-by: Ping-Ke Shih <pkshih@realtek.com> Link: https://lore.kernel.org/r/20220324004816.6202-1-pkshih@realtek.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-04mac80211: Reset MBSSID parameters upon connectionManikanta Pubbisetty1-0/+6
Currently MBSSID parameters in struct ieee80211_bss_conf are not reset upon connection. This could be problematic with some drivers in a scenario where the device first connects to a non-transmit BSS and then connects to a transmit BSS of a Multi BSS AP. The MBSSID parameters which are set after connecting to a non-transmit BSS will not be reset and the same parameters will be passed on to the driver during the subsequent connection to a transmit BSS of a Multi BSS AP. For example, firmware running on the ath11k device uses the Multi BSS data for tracking the beacon of a non-transmit BSS and reports the driver when there is a beacon miss. If we do not reset the MBSSID parameters during the subsequent connection to a transmit BSS, then the driver would have wrong MBSSID data and FW would be looking for an incorrect BSSID in the MBSSID beacon of a Multi BSS AP and reports beacon loss leading to an unstable connection. Reset the MBSSID parameters upon every connection to solve this problem. Fixes: 78ac51f81532 ("mac80211: support multi-bssid") Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com> Link: https://lore.kernel.org/r/20220428052744.27040-1-quic_mpubbise@quicinc.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-04mac80211: fix rx reordering with non explicit / psmp ack policyFelix Fietkau1-2/+1
When the QoS ack policy was set to non explicit / psmp ack, frames are treated as not being part of a BA session, which causes extra latency on reordering. Fix this by only bypassing reordering for packets with no-ack policy Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20220420105038.36443-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-05-04Merge tag 'wireless-next-2022-05-03' of ↵Jakub Kicinski28-342/+447
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v5.19 First set of patches for v5.19 and this is a big one. We have two new drivers, a change in mac80211 STA API affecting most drivers and ath11k getting support for WCN6750. And as usual lots of fixes and cleanups all over. Major changes: new drivers - wfx: silicon labs devices - plfxlc: pureLiFi X, XL, XC devices mac80211 - host based BSS color collision detection - prepare sta handling for IEEE 802.11be Multi-Link Operation (MLO) support rtw88 - support TP-Link T2E devices rtw89 - support firmware crash simulation - preparation for 8852ce hardware support ath11k - Wake-on-WLAN support for QCA6390 and WCN6855 - device recovery (firmware restart) support for QCA6390 and WCN6855 - support setting Specific Absorption Rate (SAR) for WCN6855 - read country code from SMBIOS for WCN6855/QCA6390 - support for WCN6750 wcn36xx - support for transmit rate reporting to user space * tag 'wireless-next-2022-05-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (228 commits) rtw89: 8852c: rfk: add DPK rtw89: 8852c: rfk: add IQK rtw89: 8852c: rfk: add RX DCK rtw89: 8852c: rfk: add RCK rtw89: 8852c: rfk: add TSSI rtw89: 8852c: rfk: add LCK rtw89: 8852c: rfk: add DACK rtw89: 8852c: rfk: add RFK tables plfxlc: fix le16_to_cpu warning for beacon_interval rtw88: remove a copy of the NAPI_POLL_WEIGHT define carl9170: tx: fix an incorrect use of list iterator wil6210: use NAPI_POLL_WEIGHT for napi budget ath10k: remove a copy of the NAPI_POLL_WEIGHT define ath11k: Add support for WCN6750 device ath11k: Datapath changes to support WCN6750 ath11k: HAL changes to support WCN6750 ath11k: Add QMI changes for WCN6750 ath11k: Fetch device information via QMI for WCN6750 ath11k: Add register access logic for WCN6750 ath11k: Add HW params for WCN6750 ... ==================== Link: https://lore.kernel.org/r/20220503153622.C1671C385A4@smtp.kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-11mac80211: prepare sta handling for MLO supportSriram R27-332/+385
Currently in mac80211 each STA object is represented using sta_info datastructure with the associated STA specific information and drivers access ieee80211_sta part of it. With MLO (Multi Link Operation) support being added in 802.11be standard, though the association is logically with a single Multi Link capable STA, at the physical level communication can happen via different advertised links (uniquely identified by Channel, operating class, BSSID) and hence the need to handle multiple link STA parameters within a composite sta_info object called the MLD STA. The different link STA part of MLD STA are identified using the link address which can be same or different as the MLD STA address and unique link id based on the link vif. To support extension of such a model, the sta_info datastructure is modified to hold multiple link STA objects with link specific params currently within sta_info moved to this new structure. Similarly this is done for ieee80211_sta as well which will be accessed within mac80211 as well as by drivers, hence trivial driver changes are expected to support this. For current non MLO supported drivers, only one link STA is present and link information is accessed via 'deflink' member. For MLO drivers, we still need to define the APIs etc. to get the correct link ID and access the correct part of the station info. Currently in mac80211, all link STA info are accessed directly via deflink. These will be updated to access via link pointers indexed by link id with MLO support patches, with link id being 0 for non MLO supported cases. Except for couple of macro related changes, below spatch takes care of updating mac80211 and driver code to access to the link STA info via deflink. @ieee80211_sta@ struct ieee80211_sta *s; struct sta_info *si; identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr}; @@ ( s-> - var + deflink.var | si->sta. - var + deflink.var ) @sta_info@ struct sta_info *si; identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth}; @@ ( si-> - var + deflink.var ) Signed-off-by: Sriram R <quic_srirrama@quicinc.com> Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com [remove MLO-drivers notes from commit message, not clear yet; run spatch] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-04-11mac80211: minstrel_ht: fix where rate stats are stored (fixes debugfs output)Peter Seiderer1-0/+3
Using an ath9k card the debugfs output of minstrel_ht looks like the following (note the zero values for the first four rates sum-of success/attempts): best ____________rate__________ ____statistics___ _____last____ ______sum-of________ mode guard # rate [name idx airtime max_tp] [avg(tp) avg(prob)] [retry|suc|att] [#success | #attempts] OFDM 1 DP 6.0M 272 1640 5.2 3.1 53.8 3 0 0 0 0 OFDM 1 C 9.0M 273 1104 7.7 4.6 53.8 4 0 0 0 0 OFDM 1 B 12.0M 274 836 10.0 6.0 53.8 4 0 0 0 0 OFDM 1 A S 18.0M 275 568 14.3 8.5 53.8 5 0 0 0 0 OFDM 1 S 24.0M 276 436 18.1 0.0 0.0 5 0 1 80 1778 OFDM 1 36.0M 277 300 24.9 0.0 0.0 0 0 1 0 107 OFDM 1 S 48.0M 278 236 30.4 0.0 0.0 0 0 0 0 75 OFDM 1 54.0M 279 212 33.0 0.0 0.0 0 0 0 0 72 Total packet count:: ideal 16582 lookaround 885 Average # of aggregated frames per A-MPDU: 1.0 Debugging showed that the rate statistics for the first four rates where stored in the MINSTREL_CCK_GROUP instead of the MINSTREL_OFDM_GROUP because in minstrel_ht_get_stats() the supported check was not honoured as done in various other places, e.g net/mac80211/rc80211_minstrel_ht_debugfs.c: 74 if (!(mi->supported[i] & BIT(j))) 75 continue; With the patch applied the output looks good: best ____________rate__________ ____statistics___ _____last____ ______sum-of________ mode guard # rate [name idx airtime max_tp] [avg(tp) avg(prob)] [retry|suc|att] [#success | #attempts] OFDM 1 D 6.0M 272 1640 5.2 5.2 100.0 3 0 0 1 1 OFDM 1 C 9.0M 273 1104 7.7 7.7 100.0 4 0 0 38 38 OFDM 1 B 12.0M 274 836 10.0 9.9 89.5 4 2 2 372 395 OFDM 1 A P 18.0M 275 568 14.3 14.3 97.2 5 52 53 6956 7181 OFDM 1 S 24.0M 276 436 18.1 0.0 0.0 0 0 1 6 163 OFDM 1 36.0M 277 300 24.9 0.0 0.0 0 0 1 0 35 OFDM 1 S 48.0M 278 236 30.4 0.0 0.0 0 0 0 0 38 OFDM 1 S 54.0M 279 212 33.0 0.0 0.0 0 0 0 0 38 Total packet count:: ideal 7097 lookaround 287 Average # of aggregated frames per A-MPDU: 1.0 Signed-off-by: Peter Seiderer <ps.report@gmx.net> Link: https://lore.kernel.org/r/20220404165414.1036-1-ps.report@gmx.net Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-04-11mac80211: introduce BSS color collision detectionLorenzo Bianconi2-0/+47
Add ieee80211_rx_check_bss_color_collision routine in order to introduce BSS color collision detection in mac80211 if it is not supported in HW/FW (e.g. for mt7915 chipset). Add IEEE80211_HW_DETECTS_COLOR_COLLISION flag to let the driver notify BSS color collision detection is supported in HW/FW. Set this for ath11k which apparently didn't need this code. Tested-by: Peter Chiu <Chui-Hao.Chiu@mediatek.com> Co-developed-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/a05eeeb1841a84560dc5aaec77894fcb69a54f27.1648204871.git.lorenzo@kernel.org [clarify commit message a bit, move flag to mac80211] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-04-11mac80211: protect ieee80211_assign_beacon with next_beacon checkLorenzo Bianconi1-10/+12
Even if it is not a real issue since ieee80211_set_after_csa_beacon() or ieee80211_set_after_color_change_beacon() are run only when csa or bcc is active, move next_beacon check before running ieee80211_assign_beacon routine. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/041764ed7e9781bcee66c33b41f1365aa4205932.1649327683.git.lorenzo@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-04-11mac80211: fix ht_capa printout in debugfsBen Greear1-1/+1
Don't use sizeof(pointer) when calculating scnprintf offset. Fixes: 01f84f0ed3b4 ("mac80211: reduce stack usage in debugfs") Signed-off-by: Ben Greear <greearb@candelatech.com> Link: https://lore.kernel.org/r/20220406175659.20611-1-greearb@candelatech.com [correct the Fixes tag] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-15mac80211: update bssid_indicator in ieee80211_assign_beaconLorenzo Bianconi1-0/+3
Update bssid_indicator in ieee80211_bss_conf according to the number of bssid in the set. Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Link: https://lore.kernel.org/r/f92317e002fca9933f05a445fcefb4f53291d601.1645702516.git.lorenzo@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-15mac80211: MBSSID channel switchJohn Crispin1-2/+24
Trigger ieee80211_csa_finish() on the non-transmitting interfaces when channel switch concludes on the transmitting interface. Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Co-developed-by: Aloka Dixit <alokad@codeaurora.org> Signed-off-by: Aloka Dixit <alokad@codeaurora.org> Signed-off-by: John Crispin <john@phrozen.org> Link: https://lore.kernel.org/r/6fde4d7f9fa387494f46a7aa4a584478dcda06f1.1645702516.git.lorenzo@kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-15mac80211: MBSSID beacon handling in AP modeLorenzo Bianconi3-14/+124
Add new fields in struct beacon_data to store all MBSSID elements. Generate a beacon template which includes all MBSSID elements. Move CSA offset to reflect the MBSSID element length. Co-developed-by: Aloka Dixit <alokad@codeaurora.org> Signed-off-by: Aloka Dixit <alokad@codeaurora.org> Co-developed-by: John Crispin <john@phrozen.org> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Tested-by: Money Wang <money.wang@mediatek.com> Link: https://lore.kernel.org/r/5322db3c303f431adaf191ab31c45e151dde5465.1645702516.git.lorenzo@kernel.org [small cleanups] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-15mac80211: always have ieee80211_sta_restart()Johannes Berg1-1/+1
When CONFIG_PM isn't defined we don't have the function ieee80211_sta_restart() compiled in, but we always need it now for firmware restart. Move it out of the ifdef. Fixes: 7d352ccf1e99 ("mac80211: Add support to trigger sta disconnect on hardware restart") Link: https://lore.kernel.org/r/20220312221957.1fa96c72db51.I8ecaa5f9402fede0272161e0531ab930b97fba3e@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-12Merge tag 'wireless-next-2022-03-11' of ↵Jakub Kicinski12-79/+571
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Johannes Berg says: ==================== brcmfmac * add BCM43454/6 support rtw89 * add support for 160 MHz channels and 6 GHz band * hardware scan support iwlwifi * support UHB TAS enablement via BIOS * remove a bunch of W=1 warnings * add support for channel switch offload * support 32 Rx AMPDU sessions in newer devices * add support for a couple of new devices * add support for band disablement via BIOS mt76 * mt7915 thermal management improvements * SAR support for more mt76 drivers * mt7986 wmac support on mt7915 ath11k * debugfs interface to configure firmware debug log level * debugfs interface to test Target Wake Time (TWT) * provide 802.11ax High Efficiency (HE) data via radiotap ath9k * use hw_random API instead of directly dumping into random.c wcn36xx * fix wcn3660 to work on 5 GHz band ath6kl * add device ID for WLU5150-D81 cfg80211/mac80211 * initial EHT (from 802.11be) support (EHT rates, 320 MHz, larger block-ack) * support disconnect on HW restart * tag 'wireless-next-2022-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (247 commits) mac80211: Add support to trigger sta disconnect on hardware restart mac80211: fix potential double free on mesh join mac80211: correct legacy rates check in ieee80211_calc_rx_airtime nl80211: fix typo of NL80211_IF_TYPE_OCB in documentation mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possible mac80211: replace DEFINE_SIMPLE_ATTRIBUTE with DEFINE_DEBUGFS_ATTRIBUTE rtw89: 8852c: process logic efuse map rtw89: 8852c: process efuse of phycap rtw89: support DAV efuse reading operation rtw89: 8852c: add chip::dle_mem rtw89: add page_regs to handle v1 chips rtw89: add chip_info::{h2c,c2h}_reg to support more chips rtw89: add hci_func_en_addr to support variant generation rtw89: add power_{on/off}_func rtw89: read chip version depends on chip ID rtw89: pci: use a struct to describe all registers address related to DMA channel rtw89: pci: add V1 of PCI channel address rtw89: pci: add struct rtw89_pci_info rtw89: 8852c: add 8852c empty files MAINTAINERS: add devicetree bindings entry for mt76 ... ==================== Link: https://lore.kernel.org/r/20220311124029.213470-1-johannes@sipsolutions.net Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-11mac80211: Add support to trigger sta disconnect on hardware restartYoughandhar Chintala3-3/+45
Currently in case of target hardware restart, we just reconfig and re-enable the security keys and enable the network queues to start data traffic back from where it was interrupted. Many ath10k wifi chipsets have sequence numbers for the data packets assigned by firmware and the mac sequence number will restart from zero after target hardware restart leading to mismatch in the sequence number expected by the remote peer vs the sequence number of the frame sent by the target firmware. This mismatch in sequence number will cause out-of-order packets on the remote peer and all the frames sent by the device are dropped until we reach the sequence number which was sent before we restarted the target hardware In order to fix this, we trigger a sta disconnect, in case of target hw restart. After this there will be a fresh connection and thereby avoiding the dropping of frames by remote peer. The right fix would be to pull the entire data path into the host which is not feasible or would need lots of complex changes and will still be inefficient. Tested on ath10k using WCN3990, QCA6174 Signed-off-by: Youghandhar Chintala <youghand@codeaurora.org> Link: https://lore.kernel.org/r/20220308115325.5246-2-youghand@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-11mac80211: fix potential double free on mesh joinLinus Lüssing1-3/+0
While commit 6a01afcf8468 ("mac80211: mesh: Free ie data when leaving mesh") fixed a memory leak on mesh leave / teardown it introduced a potential memory corruption caused by a double free when rejoining the mesh: ieee80211_leave_mesh() -> kfree(sdata->u.mesh.ie); ... ieee80211_join_mesh() -> copy_mesh_setup() -> old_ie = ifmsh->ie; -> kfree(old_ie); This double free / kernel panics can be reproduced by using wpa_supplicant with an encrypted mesh (if set up without encryption via "iw" then ifmsh->ie is always NULL, which avoids this issue). And then calling: $ iw dev mesh0 mesh leave $ iw dev mesh0 mesh join my-mesh Note that typically these commands are not used / working when using wpa_supplicant. And it seems that wpa_supplicant or wpa_cli are going through a NETDEV_DOWN/NETDEV_UP cycle between a mesh leave and mesh join where the NETDEV_UP resets the mesh.ie to NULL via a memcpy of default_mesh_setup in cfg80211_netdev_notifier_call, which then avoids the memory corruption, too. The issue was first observed in an application which was not using wpa_supplicant but "Senf" instead, which implements its own calls to nl80211. Fixing the issue by removing the kfree()'ing of the mesh IE in the mesh join function and leaving it solely up to the mesh leave to free the mesh IE. Cc: stable@vger.kernel.org Fixes: 6a01afcf8468 ("mac80211: mesh: Free ie data when leaving mesh") Reported-by: Matthias Kretschmer <mathias.kretschmer@fit.fraunhofer.de> Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Tested-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de> Link: https://lore.kernel.org/r/20220310183513.28589-1-linus.luessing@c0d3.blue Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-11mac80211: correct legacy rates check in ieee80211_calc_rx_airtimeMeiChia Chiu1-1/+3
There are no legacy rates on 60GHz or sub-1GHz band, so modify the check. Signed-off-by: Ryder Lee <ryder.lee@mediatek.com> Signed-off-by: MeiChia Chiu <MeiChia.Chiu@mediatek.com> Link: https://lore.kernel.org/r/20220308021645.16272-1-MeiChia.Chiu@mediatek.com [Ghz -> GHz] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-11mac80211: Use GFP_KERNEL instead of GFP_ATOMIC when possibleChristophe JAILLET1-1/+1
Previous memory allocations in this function already use GFP_KERNEL, so use __dev_alloc_skb() and an explicit GFP_KERNEL instead of an implicit GFP_ATOMIC. This gives more opportunities of successful allocation. Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/194a0e2ff00c3fae88cc9fba47431747360c8242.1645345378.git.christophe.jaillet@wanadoo.fr Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-03-03Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski4-15/+27
net/batman-adv/hard-interface.c commit 690bb6fb64f5 ("batman-adv: Request iflink once in batadv-on-batadv check") commit 6ee3c393eeb7 ("batman-adv: Demote batadv-on-batadv skip error message") https://lore.kernel.org/all/20220302163049.101957-1-sw@simonwunderlich.de/ net/smc/af_smc.c commit 4d08b7b57ece ("net/smc: Fix cleanup when register ULP fails") commit 462791bbfa35 ("net/smc: add sysctl interface for SMC") https://lore.kernel.org/all/20220302112209.355def40@canb.auug.org.au/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-01mac80211: treat some SAE auth steps as finalJohannes Berg2-5/+13
When we get anti-clogging token required (added by the commit mentioned below), or the other status codes added by the later commit 4e56cde15f7d ("mac80211: Handle special status codes in SAE commit") we currently just pretend (towards the internal state machine of authentication) that we didn't receive anything. This has the undesirable consequence of retransmitting the prior frame, which is not expected, because the timer is still armed. If we just disarm the timer at that point, it would result in the undesirable side effect of being in this state indefinitely if userspace crashes, or so. So to fix this, reset the timer and set a new auth_data->waiting in order to have no more retransmissions, but to have the data destroyed when the timer actually fires, which will only happen if userspace didn't continue (i.e. crashed or abandoned it.) Fixes: a4055e74a2ff ("mac80211: Don't destroy auth data in case of anti-clogging") Reported-by: Jouni Malinen <j@w1.fi> Link: https://lore.kernel.org/r/20220224103932.75964e1d7932.Ia487f91556f29daae734bf61f8181404642e1eec@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski1-8/+21
No conflicts. Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-16mac80211: parse AddBA request with extended AddBA elementMordechay Goodstein1-3/+15
In EHT requesting aggregation with 1K needs the use of extended the AddBA element for the buffer size, so add the logic to parse it and make sure it's in limits of the EHT aggregation size. Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Link: https://lore.kernel.org/r/20220214173004.8209cae9d9e4.I434f5588602f83b4e658c660120040913b3a2e3d@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: calculate max RX NSS for EHT modeMordechay Goodstein1-1/+13
If the station supports EHT mode, calculate the maximum RX NSS from EHT station capabilities. Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Link: https://lore.kernel.org/r/20220214173004.cf61972c8919.I54f5a416f0789bf4eefad04703d941b6755f6dd6@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Add support for storing station EHT capabilitiesIlan Peer1-0/+8
When a station configuration is updated, also update the station EHT capabilities. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.47213ffb23a8.I15c6c8430e1a0184b1322e40f1727ed4f17b04e2@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Handle station association response with EHTIlan Peer5-3/+114
When the association is an EHT association, parse the EHT element from the association response and update the station's EHT capabilities accordingly. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.f33574718755.I21182234c5303d9423eabd5eb997e7cf75f8e0c8@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Add EHT capabilities to association/probe requestIlan Peer4-2/+144
Add the EHT capabilities element to both probe request and association request frames, if advertised by the driver. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.2ec94388acee.I40d2ef06099cb091e9c2c01f8ef521b993a3d559@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Add initial support for EHT and 320 MHz channelsIlan Peer6-59/+209
Add initial support for EHT and 320 MHz bandwidth in mac80211. As a new IEEE80211_STA_RX_BW_320 is added to enum ieee80211_sta_rx_bandwidth, update the drivers to avoid compilation warnings. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.0f144cc0bba6.Iad18111264da87eed5fd7b017f0cc6e58c604e07@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: Support parsing EHT elementsIlan Peer2-0/+14
Parse the new EHT elements in the element parsing utilities. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Link: https://lore.kernel.org/r/20220214173004.4d52ddaf1af4.Ib6beb1aa85e25b71ce40d3260b2e5b117cc42308@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16ieee80211: add EHT 1K aggregation definitionsMordechay Goodstein1-1/+1
We add the fields for parsing extended ADDBA request/respond, and new max 1K aggregation for limit ADDBA request/respond. Adjust drivers to use the proper macro, IEEE80211_MAX_AMPDU_BUF -> IEEE80211_MAX_AMPDU_BUF_HE. Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com> Link: https://lore.kernel.org/r/20220214173004.b8b447ce95b7.I0ee2554c94e89abc7a752b0f7cc7fd79c273efea@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: parse only HE capability elements with valid sizeJohannes Berg1-2/+4
The code validates the HE capability element size later, but slightly wrong, so use the new helper to do it right and only accept it if it has a good size. Link: https://lore.kernel.org/r/20220214172920.b5b06f264a61.I645ac1e2dc0ace223ef3e551cd5a71c88bd55e04@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2022-02-16mac80211: fix forwarded mesh frames AC & queue selectionNicolas Escande1-2/+2
There are two problems with the current code that have been highlighted with the AQL feature that is now enbaled by default. First problem is in ieee80211_rx_h_mesh_fwding(), ieee80211_select_queue_80211() is used on received packets to choose the sending AC queue of the forwarding packet although this function should only be called on TX packet (it uses ieee80211_tx_info). This ends with forwarded mesh packets been sent on unrelated random AC queue. To fix that, AC queue can directly be infered from skb->priority which has been extracted from QOS info (see ieee80211_parse_qos()). Second problem is the value of queue_mapping set on forwarded mesh frames via skb_set_queue_mapping() is not the AC of the packet but a hardware queue index. This may or may not work depending on AC to HW queue mapping which is driver specific. Both of these issues lead to improper AC selection while forwarding mesh packets but more importantly due to improper airtime accounting (which is done on a per STA, per AC basis) caused traffic stall with the introduction of AQL. Fixes: cf44012810cc ("mac80211: fix unnecessary frame drops in mesh fwding") Fixes: d3c1597b8d1b ("mac80211: fix forwarded mesh frame queue mapping") Co-developed-by: Remi Pommarel <repk@triplefau.lt> Signed-off-by: Remi Pommarel <repk@triplefau.lt> Signed-off-by: Nicolas Escande <nico.escande@gmail.com> Link: https://lore.kernel.org/r/20220214173214.368862-1-nico.escande@gmail.com Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.39.0) at 2024-07-31 11:47:07 +0300