Age | Commit message (Collapse) | Author | Files | Lines |
|
It was not possible to register a UART driver due
to a bad condition.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NCI deactivate management was modified to support all NCI
deactivation type. Problem is that all the API are not ready
yet for it.
Problem is that with current code, when neard asks to deactivate
the tag it sends a deactivate SLEEP but nobody will then send a
IDLE deactivate. This IDLE deactivate is mandatory since NFC
controller can only be unlocked by DH.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Some NFC controller supports UART as host interface.
As with SPI, a lot of code can be shared between vendor
drivers. This patch add the generic support of UART and
provides some extension API for vendor specific needs.
This code is strongly inspired by the Bluetooth HCI ldisc
implementation. NCI UART vendor drivers will have to register
themselves to this layer via nci_uart_register.
Underlying tty will have to be configured from user land
thanks to an ioctl.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Drivers implementing proprietary ops may need it now.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When closing the device some data (proprietary commands)
might be sent. The core state machine needs to be set for
correct command execution.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Handle allowing to send proprietary nci commands anywhere in the nci
state machine.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Some device may need to execute some proprietary commands
in order to "wake-up"; Before the nci state initialization.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
setup was executed in any case, even if NCI_RESET failed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow for drivers to explicitly define handlers for each
proprietary notifications and responses they expect to support.
Reviewed-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Several of these goto exit; uses should be direct returns
as skb is not yet initialized by nci_hci_get_param().
Miscellanea:
o Use !memcmp instead of memcmp() == 0
o Remove unnecessary goto from if () {... goto exit;} else {...} exit:
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
A simple forward for firmware download (i.e. sending a new firmware
to the NFC adapter) from the NFC subsystem to the drivers.
This feature is required to update the firmware of NXP-NCI NFC
controllers but can be used by any NCI driver.
This feature has been present in the HCI subsystem since 9a695d.
Signed-off-by: Clément Perrochaud <clement.perrochaud@effinnov.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEE_DISCOVER_CMD is a specified NCI command used to discover
NFCEE IDs.
Move nci_nfcee_discover() call to nci_discover_se() in order to
guarantee:
- NFCEE_DISCOVER_CMD run when the NCI state machine is initialized
- NFCEE_DISCOVER_CMD is not run in case there is not discover_se
hook defined by a NFC device driver.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
conn_info is currently allocated only after nfcee_discovery_ntf
which is not generic enough for logical connection other than
NFCEE. The corresponding conn_info is now created in
nci_core_conn_create_rsp().
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
For consistency sake change nci_core_conn_create_rsp structure
credits field to credits_cnt.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current implementation limits nci_core_conn_create_req()
to only manage NCI_DESTINATION_NFCEE.
Add new parameters to nci_core_conn_create() to support all
destination types described in the NCI specification.
Because there are some parameters with variable size dynamic
buffer allocation is needed.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The NCI_STATIC_RF_CONN_ID logical connection is the most used
connection. Keeping it directly accessible in the nci_dev
structure will simplify and optimize the access.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When receiving an interface activation notification, if
the RF interface is NCI_RF_INTERFACE_NFCEE_DIRECT, we
need to ignore the following parameters and change the NCI
state machine to NCI_LISTEN_ACTIVE. According to the NCI
specification, the parameters should be 0 and shall be
ignored.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The NFCC sends an NCI_OP_RF_NFCEE_ACTION_NTF notification
to the host (DH) to let it know that for example an RF
transaction with a payment reader is done.
For now the notification handler is empty.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
According to the NCI specification, one can use HCI over NCI
to talk with specific NFCEE. The HCI network is viewed as one
logical NFCEE.
This is needed to support secure element running HCI only
firmwares embedded on an NCI capable chipset, like e.g. the
st21nfcb.
There is some duplication between this piece of code and the
HCI core code, but the latter would need to be abstracted even
more to be able to use NCI as a logical transport for HCP packets.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to communicate with an NFCEE, we need to open a logical
connection to it, by sending the NCI_OP_CORE_CONN_CREATE_CMD
command to the NFCC. It's left up to the drivers to decide when
to close an already opened logical connection.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEEs can be enabled or disabled by sending the
NCI_OP_NFCEE_MODE_SET_CMD command to the NFCC. This patch
provides an API for drivers to enable and disable e.g. their
NCI discoveredd secure elements.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NFCEEs (NFC Execution Environment) have to be explicitly
discovered by sending the NCI_OP_NFCEE_DISCOVER_CMD
command. The NFCC will respond to this command by telling
us how many NFCEEs are connected to it. Then the NFCC sends
a notification command for each and every NFCEE connected.
Here we implement support for sending
NCI_OP_NFCEE_DISCOVER_CMD command, receiving the response
and the potential notifications.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The current NCI core only support the RF static connection.
For other NFC features such as Secure Element communication, we
may need to create logical connections to the NFCEE (Execution
Environment.
In order to track each logical connection ID dynamically, we add a
linked list of connection info pointers to the nci_dev structure.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The maximum size of ATR_REQ and ATR_RES is 64 bytes.
The maximum number of General Bytes is calculated by
the maximum number of data bytes in the ATR_REQ/ATR_RES,
substracted by the number of mandatory data bytes.
ATR_REQ: 16 mandatory data bytes, giving a maximum of
48 General Bytes.
ATR_RES: 17 mandatory data bytes, giving a maximum of
47 General Bytes.
Regression introduced in commit a99903ec.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Fixing: net/nfc/nci/ntf.c:106:31: warning: cast to restricted __le16
message when building with make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
nci_rf_deactivate_req only support NCI_DEACTIVATE_TYPE_IDLE_MODE.
In some situation, it might be necessary to be able to support other
NCI_DEACTIVATE_TYPE such as NCI_DEACTIVATE_TYPE_SLEEP_MODE in order for
example to reactivate the selected target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
A notification for rf deaction can be IDLE_MODE, SLEEP_MODE,
SLEEP_AF_MODE and DISCOVERY. According to each type and the NCI
state machine is different (see figure 10 RF Communication State
Machine in NCI specification)
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The nci status byte was ignored. In case of tag reading for example,
if the tag is removed from the antenna there is no way for the upper
layers (aka: stack) to get inform about such event.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
se_io allows to send apdu over the CLF to the embedded Secure Element.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
secure element
Some NFC controller using NCI protocols may need a proprietary commands
flow to disable a secure element
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
secure element
Some NFC controller using NCI protocols may need a proprietary commands
flow to enable a secure element
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
available secure element
Some NFC controller using NCI protocols may need a proprietary commands
flow to discover all available secure element
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Fix sparse warning introduced by commit: 9e87f9a9c4c4754508b2c2638fbde9e10c7a103b
It was generating the following warning:
net/nfc/nci/ntf.c:170:7: sparse: symbol 'nci_get_prop_rf_protocol' was not declared. Should it be static?
Procedure to reproduce it:
# apt-get install sparse
git checkout 9e87f9a9c4c4754508b2c2638fbde9e10c7a103b
make ARCH=x86_64 allmodconfig
make C=1 CF=-D__CHECK_ENDIAN__
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Before signaling the deactivation, send a deactivation request if in
RFST_DISCOVERY state because neard assumes polling is stopped and will
try to restart it.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When the deactivation type reported by RF_DEACTIVATE_NTF is Discovery, go in
RFST_DISCOVERY state. The NFCC stays in Poll mode and/or Listen mode.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As specified in NCI 1.0 and NCI 1.1, when using the NFC-DEP RF Interface, the
DH and the NFCC shall only use the Static RF Connection for data communication
with a Remote NFC Endpoint.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The Target responds to the ATR_REQ with the ATR_RES. Configure the General
Bytes in ATR_RES with the first three octets equal to the NFC Forum LLCP
magic number, followed by some LLC Parameters TLVs described in section
4.5 of [LLCP].
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Changes:
* Extract the Listen mode activation parameters from RF_INTF_ACTIVATED_NTF.
* Store the General Bytes of ATR_REQ.
* Signal that Target mode is activated in case of an activation in NFC-DEP.
* Update the NCI state accordingly.
* Use the various constants defined in nfc.h.
* Fix the ATR_REQ and ATR_RES maximum size. As per NCI 1.0 and NCI 1.1, the
Activation Parameters for both Poll and Listen mode contain all the bytes of
ATR_REQ/ATR_RES starting and including Byte 3 as defined in [DIGITAL].
In [DIGITAL], the maximum size of ATR_REQ/ATR_RES is 64 bytes and they are
numbered starting from Byte 1.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Send LA_SEL_INFO and LF_PROTOCOL_TYPE with NFC-DEP protocol enabled.
Configure 212 Kbit/s and 412 Kbit/s bit rates for Listen F.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The Target mode protocols are given to the nci_start_poll() function
but were previously ignored.
To enable P2P Target, when NFC-DEP is requested as a Target mode protocol, add
NFC-A and NFC-F Passive Listen modes in RF_DISCOVER_CMD command.
Signed-off-by: Julien Lefrique <lefrique@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In NFC Forum NCI specification, some RF Protocol values are
reserved for proprietary use (from 0x80 to 0xfe).
Some CLF vendor may need to use one value within this range
for specific technology.
Furthermore, some CLF may not becompliant with NFC Froum NCI
specification 2.0 and therefore will not support RF Protocol
value 0x06 for PROTOCOL_T5T as mention in a draft specification
and in a recent push.
Adding get_rf_protocol handle to the nci_ops structure will
help to set the correct technology to target.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
NCI RF FRAME interface is used for all kind of tags
except ISODEP ones. So for all other kind of tags the
status byte has to be removed.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
All contexts have to be initiliazed before calling
nfc_register_device otherwise it is possible to call
nci_dev_up before ending the nci_register_device
function. In such case kernel will crash on non
initialized variables.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Update nci.h to respect latest NCI specification proposal
(stop using proprietary opcodes). Handle ISO15693 parameters
in NCI_RF_ACTIVATED_NTF handler.
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add T1T matching with Jewel during notification.
It was causing "the target found does not have the desired protocol"
to show up.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
So that anyone listening on SOCKPROTO_RAW for raw frames will get all
NCI frames, in both directions. This actually implements userspace NFC
NCI sniffing.
It's now up to userspace to decode those frames.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
ATR_RES response received within Activation Parameters is already
in correct order. Reversing it fails LLCP magic number check and
so P2P functionality fails.
Signed-off-by: Hiren Tandel <hirent@marvell.com>
Signed-off-by: Rahul Tank <rahult@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|