Age | Commit message (Collapse) | Author | Files | Lines |
|
In preparation for netdev->dev_addr being constant
make all relevant arguments in tipc constant.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These patches fix a series of spelling errors in net/tipc module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix tipc header files for adding to the networking docbook.
Remove some uses of "/**" that were not kernel-doc notation.
Fix some source formatting to eliminate Sphinx warnings.
Add missing struct member and function argument kernel-doc descriptions.
Correct the description of a couple of struct members that were
marked as "(FIXME)".
Documentation/networking/tipc:18: ../net/tipc/name_table.h:65: WARNING: Unexpected indentation.
Documentation/networking/tipc:18: ../net/tipc/name_table.h:66: WARNING: Block quote ends without a blank line; unexpected unindent.
../net/tipc/bearer.h:128: warning: Function parameter or member 'min_win' not described in 'tipc_media'
../net/tipc/bearer.h:128: warning: Function parameter or member 'max_win' not described in 'tipc_media'
../net/tipc/bearer.h:171: warning: Function parameter or member 'min_win' not described in 'tipc_bearer'
../net/tipc/bearer.h:171: warning: Function parameter or member 'max_win' not described in 'tipc_bearer'
../net/tipc/bearer.h:171: warning: Function parameter or member 'disc' not described in 'tipc_bearer'
../net/tipc/bearer.h:171: warning: Function parameter or member 'up' not described in 'tipc_bearer'
../net/tipc/bearer.h:171: warning: Function parameter or member 'refcnt' not described in 'tipc_bearer'
../net/tipc/name_distr.h:68: warning: Function parameter or member 'port' not described in 'distr_item'
../net/tipc/name_table.h:111: warning: Function parameter or member 'services' not described in 'name_table'
../net/tipc/name_table.h:111: warning: Function parameter or member 'cluster_scope_lock' not described in 'name_table'
../net/tipc/name_table.h:111: warning: Function parameter or member 'rc_dests' not described in 'name_table'
../net/tipc/name_table.h:111: warning: Function parameter or member 'snd_nxt' not described in 'name_table'
../net/tipc/subscr.h:67: warning: Function parameter or member 'kref' not described in 'tipc_subscription'
../net/tipc/subscr.h:67: warning: Function parameter or member 'net' not described in 'tipc_subscription'
../net/tipc/subscr.h:67: warning: Function parameter or member 'service_list' not described in 'tipc_subscription'
../net/tipc/subscr.h:67: warning: Function parameter or member 'conid' not described in 'tipc_subscription'
../net/tipc/subscr.h:67: warning: Function parameter or member 'inactive' not described in 'tipc_subscription'
../net/tipc/subscr.h:67: warning: Function parameter or member 'lock' not described in 'tipc_subscription'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We introduce a simple variable window congestion control for links.
The algorithm is inspired by the Reno algorithm, covering both 'slow
start', 'congestion avoidance', and 'fast recovery' modes.
- We introduce hard lower and upper window limits per link, still
different and configurable per bearer type.
- We introduce a 'slow start theshold' variable, initially set to
the maximum window size.
- We let a link start at the minimum congestion window, i.e. in slow
start mode, and then let is grow rapidly (+1 per rceived ACK) until
it reaches the slow start threshold and enters congestion avoidance
mode.
- In congestion avoidance mode we increment the congestion window for
each window-size number of acked packets, up to a possible maximum
equal to the configured maximum window.
- For each non-duplicate NACK received, we drop back to fast recovery
mode, by setting the both the slow start threshold to and the
congestion window to (current_congestion_window / 2).
- If the timeout handler finds that the transmit queue has not moved
since the previous timeout, it drops the link back to slow start
and forces a probe containing the last sent sequence number to the
sent to the peer, so that this can discover the stale situation.
This change does in reality have effect only on unicast ethernet
transport, as we have seen that there is no room whatsoever for
increasing the window max size for the UDP bearer.
For now, we also choose to keep the limits for the broadcast link
unchanged and equal.
This algorithm seems to give a 50-100% throughput improvement for
messages larger than MTU.
Suggested-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit offers an option to encrypt and authenticate all messaging,
including the neighbor discovery messages. The currently most advanced
algorithm supported is the AEAD AES-GCM (like IPSec or TLS). All
encryption/decryption is done at the bearer layer, just before leaving
or after entering TIPC.
Supported features:
- Encryption & authentication of all TIPC messages (header + data);
- Two symmetric-key modes: Cluster and Per-node;
- Automatic key switching;
- Key-expired revoking (sequence number wrapped);
- Lock-free encryption/decryption (RCU);
- Asynchronous crypto, Intel AES-NI supported;
- Multiple cipher transforms;
- Logs & statistics;
Two key modes:
- Cluster key mode: One single key is used for both TX & RX in all
nodes in the cluster.
- Per-node key mode: Each nodes in the cluster has one specific TX key.
For RX, a node requires its peers' TX key to be able to decrypt the
messages from those peers.
Key setting from user-space is performed via netlink by a user program
(e.g. the iproute2 'tipc' tool).
Internal key state machine:
Attach Align(RX)
+-+ +-+
| V | V
+---------+ Attach +---------+
| IDLE |---------------->| PENDING |(user = 0)
+---------+ +---------+
A A Switch| A
| | | |
| | Free(switch/revoked) | |
(Free)| +----------------------+ | |Timeout
| (TX) | | |(RX)
| | | |
| | v |
+---------+ Switch +---------+
| PASSIVE |<----------------| ACTIVE |
+---------+ (RX) +---------+
(user = 1) (user >= 1)
The number of TFMs is 10 by default and can be changed via the procfs
'net/tipc/max_tfms'. At this moment, as for simplicity, this file is
also used to print the crypto statistics at runtime:
echo 0xfff1 > /proc/sys/net/tipc/max_tfms
The patch defines a new TIPC version (v7) for the encryption message (-
backward compatibility as well). The message is basically encapsulated
as follows:
+----------------------------------------------------------+
| TIPCv7 encryption | Original TIPCv2 | Authentication |
| header | packet (encrypted) | Tag |
+----------------------------------------------------------+
The throughput is about ~40% for small messages (compared with non-
encryption) and ~9% for large messages. With the support from hardware
crypto i.e. the Intel AES-NI CPU instructions, the throughput increases
upto ~85% for small messages and ~55% for large messages.
By default, the new feature is inactive (i.e. no encryption) until user
sets a key for TIPC. There is however also a new option - "TIPC_CRYPTO"
in the kernel configuration to enable/disable the new code when needed.
MAINTAINERS | add two new files 'crypto.h' & 'crypto.c' in tipc
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a need to support the crypto asynchronous operations in the later
commits, apart from the current RCU mechanism for bearer pointer, we
add a 'refcnt' to the bearer object as well.
So, a bearer can be hold via 'tipc_bearer_hold()' without being freed
even though the bearer or interface can be disabled in the meanwhile.
If that happens, the bearer will be released then when the crypto
operation is completed and 'tipc_bearer_put()' is called.
Acked-by: Ying Xue <ying.xue@windreiver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since node internal messages are passed directly to the socket, it is not
possible to observe those messages via tcpdump or wireshark.
We now remedy this by making it possible to clone such messages and send
the clones to the loopback interface. The clones are dropped at reception
and have no functional role except making the traffic visible.
The feature is enabled if network taps are active for the loopback device.
pcap filtering restrictions require the messages to be presented to the
receiving side of the loopback device.
v3 - Function dev_nit_active used to check for network taps.
- Procedure netif_rx_ni used to send cloned messages to loopback device.
Signed-off-by: John Rutherford <john.rutherford@dektech.com.au>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As for the sake of debugging/tracing, the commit enables tracepoints in
TIPC along with some general trace_events as shown below. It also
defines some 'tipc_*_dump()' functions that allow to dump TIPC object
data whenever needed, that is, for general debug purposes, ie. not just
for the trace_events.
The following trace_events are now available:
- trace_tipc_skb_dump(): allows to trace and dump TIPC msg & skb data,
e.g. message type, user, droppable, skb truesize, cloned skb, etc.
- trace_tipc_list_dump(): allows to trace and dump any TIPC buffers or
queues, e.g. TIPC link transmq, socket receive queue, etc.
- trace_tipc_sk_dump(): allows to trace and dump TIPC socket data, e.g.
sk state, sk type, connection type, rmem_alloc, socket queues, etc.
- trace_tipc_link_dump(): allows to trace and dump TIPC link data, e.g.
link state, silent_intv_cnt, gap, bc_gap, link queues, etc.
- trace_tipc_node_dump(): allows to trace and dump TIPC node data, e.g.
node state, active links, capabilities, link entries, etc.
How to use:
Put the trace functions at any places where we want to dump TIPC data
or events.
Note:
a) The dump functions will generate raw data only, that is, to offload
the trace event's processing, it can require a tool or script to parse
the data but this should be simple.
b) The trace_tipc_*_dump() should be reserved for a failure cases only
(e.g. the retransmission failure case) or where we do not expect to
happen too often, then we can consider enabling these events by default
since they will almost not take any effects under normal conditions,
but once the rare condition or failure occurs, we get the dumped data
fully for post-analysis.
For other trace purposes, we can reuse these trace classes as template
but different events.
c) A trace_event is only effective when we enable it. To enable the
TIPC trace_events, echo 1 to 'enable' files in the events/tipc/
directory in the 'debugfs' file system. Normally, they are located at:
/sys/kernel/debug/tracing/events/tipc/
For example:
To enable the tipc_link_dump event:
echo 1 > /sys/kernel/debug/tracing/events/tipc/tipc_link_dump/enable
To enable all the TIPC trace_events:
echo 1 > /sys/kernel/debug/tracing/events/tipc/enable
To collect the trace data:
cat trace
or
cat trace_pipe > /trace.out &
To disable all the TIPC trace_events:
echo 0 > /sys/kernel/debug/tracing/events/tipc/enable
To clear the trace buffer:
echo > trace
d) Like the other trace_events, the feature like 'filter' or 'trigger'
is also usable for the tipc trace_events.
For more details, have a look at:
Documentation/trace/ftrace.txt
MAINTAINERS | add two new files 'trace.h' & 'trace.c' in tipc
Acked-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In previous commit, we changed the default emulated MTU for UDP bearers
to 14k.
This commit adds the functionality to set/change the default value
by configuring new MTU for UDP media. UDP bearer(s) have to be disabled
and enabled back for the new MTU to take effect.
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: GhantaKrishnamurthy MohanKrishna <mohan.krishna.ghanta.krishnamurthy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To facilitate the coming changes in the neighbor discovery functionality
we make some renaming and refactoring of that code. The functional changes
in this commit are trivial, e.g., that we move the message sending call in
tipc_disc_timeout() outside the spinlock protected region.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_media_set() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_bearer_set() which doesn't holding RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_bearer_enable() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce __tipc_nl_bearer_disable() which doesn't hold RTNL lock.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For a bond slave device as a tipc bearer, the dev represents the bond
interface and orig_dev represents the slave in tipc_l2_rcv_msg().
Since we decode the tipc_ptr from bonding device (dev), we fail to
find the bearer and thus tipc links are not established.
In this commit, we register the tipc protocol callback per device and
look for tipc bearer from both the devices.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the broadcast send link after 100 attempts has failed to
transfer a packet to all peers, we consider it stale, and reset
it. Thereafter it needs to re-synchronize with the peers, something
currently done by just resetting and re-establishing all links to
all peers. This has turned out to be overkill, with potentially
unwanted consequences for the remaining cluster.
A closer analysis reveals that this can be done much simpler. When
this kind of failure happens, for reasons that may lie outside the
TIPC protocol, it is typically only one peer which is failing to
receive and acknowledge packets. It is hence sufficient to identify
and reset the links only to that peer to resolve the situation, without
having to reset the broadcast link at all. This solution entails a much
lower risk of negative consequences for the own node as well as for
the overall cluster.
We implement this change in this commit.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation for the 'replicast' functionality we are going to
introduce in the next commits, we need the broadcast base structure to
store whether bearer broadcast is available at all from the currently
used bearer or bearers.
We do this by adding a new function tipc_bearer_bcast_support() to
the bearer layer, and letting the bearer selection function in
bcast.c use this to give a new boolean field, 'bcast_support' the
appropriate value.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.
As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.
Fixes: b97bf3fd8f6a ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces UDP replicast. A concept where we emulate
multicast by sending multiple unicast messages to configured peers.
The purpose of replicast is mainly to be able to use TIPC in cloud
environments where IP multicast is disabled. Using replicas to unicast
multicast messages is costly as we have to copy each skb and send the
copies individually.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 5b7066c3dd24 ("tipc: stricter filtering of packets in bearer
layer") we introduced a method of filtering out messages while a bearer
is being reset, to avoid that links may be re-created and come back in
working state while we are still in the process of shutting them down.
This solution works well, but is limited to only work with L2 media, which
is insufficient with the increasing use of UDP as carrier media.
We now replace this solution with a more generic one, by introducing a
new flag "up" in the generic struct tipc_bearer. This field will be set
and reset at the same locations as with the previous solution, while
the packet filtering is moved to the generic code for the sending side.
On the receiving side, the filtering is still done in media specific
code, but now including the UDP bearer.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new function to get the bearer name from
its id. This is used in subsequent commit.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just several instances of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In test situations with many nodes and a heavily stressed system we have
observed that the transmission broadcast link may fail due to an
excessive number of retransmissions of the same packet. In such
situations we need to reset all unicast links to all peers, in order to
reset and re-synchronize the broadcast link.
In this commit, we add a new function tipc_bearer_reset_all() to be used
in such situations. The function scans across all bearers and resets all
their pertaining links.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC based clusters are by default set up with full-mesh link
connectivity between all nodes. Those links are expected to provide
a short failure detection time, by default set to 1500 ms. Because
of this, the background load for neighbor monitoring in an N-node
cluster increases with a factor N on each node, while the overall
monitoring traffic through the network infrastructure increases at
a ~(N * (N - 1)) rate. Experience has shown that such clusters don't
scale well beyond ~100 nodes unless we significantly increase failure
discovery tolerance.
This commit introduces a framework and an algorithm that drastically
reduces this background load, while basically maintaining the original
failure detection times across the whole cluster. Using this algorithm,
background load will now grow at a rate of ~(2 * sqrt(N)) per node, and
at ~(2 * N * sqrt(N)) in traffic overhead. As an example, each node will
now have to actively monitor 38 neighbors in a 400-node cluster, instead
of as before 399.
This "Overlapping Ring Supervision Algorithm" is completely distributed
and employs no centralized or coordinated state. It goes as follows:
- Each node makes up a linearly ascending, circular list of all its N
known neighbors, based on their TIPC node identity. This algorithm
must be the same on all nodes.
- The node then selects the next M = sqrt(N) - 1 nodes downstream from
itself in the list, and chooses to actively monitor those. This is
called its "local monitoring domain".
- It creates a domain record describing the monitoring domain, and
piggy-backs this in the data area of all neighbor monitoring messages
(LINK_PROTOCOL/STATE) leaving that node. This means that all nodes in
the cluster eventually (default within 400 ms) will learn about
its monitoring domain.
- Whenever a node discovers a change in its local domain, e.g., a node
has been added or has gone down, it creates and sends out a new
version of its node record to inform all neighbors about the change.
- A node receiving a domain record from anybody outside its local domain
matches this against its own list (which may not look the same), and
chooses to not actively monitor those members of the received domain
record that are also present in its own list. Instead, it relies on
indications from the direct monitoring nodes if an indirectly
monitored node has gone up or down. If a node is indicated lost, the
receiving node temporarily activates its own direct monitoring towards
that node in order to confirm, or not, that it is actually gone.
- Since each node is actively monitoring sqrt(N) downstream neighbors,
each node is also actively monitored by the same number of upstream
neighbors. This means that all non-direct monitoring nodes normally
will receive sqrt(N) indications that a node is gone.
- A major drawback with ring monitoring is how it handles failures that
cause massive network partitionings. If both a lost node and all its
direct monitoring neighbors are inside the lost partition, the nodes in
the remaining partition will never receive indications about the loss.
To overcome this, each node also chooses to actively monitor some
nodes outside its local domain. Those nodes are called remote domain
"heads", and are selected in such a way that no node in the cluster
will be more than two direct monitoring hops away. Because of this,
each node, apart from monitoring the member of its local domain, will
also typically monitor sqrt(N) remote head nodes.
- As an optimization, local list status, domain status and domain
records are marked with a generation number. This saves senders from
unnecessarily conveying unaltered domain records, and receivers from
performing unneeded re-adaptations of their node monitoring list, such
as re-assigning domain heads.
- As a measure of caution we have added the possibility to disable the
new algorithm through configuration. We do this by keeping a threshold
value for the cluster size; a cluster that grows beyond this value
will switch from full-mesh to ring monitoring, and vice versa when
it shrinks below the value. This means that if the threshold is set to
a value larger than any anticipated cluster size (default size is 32)
the new algorithm is effectively disabled. A patch set for altering the
threshold value and for listing the table contents will follow shortly.
- This change is fully backwards compatible.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We remove a couple of leftover fields in struct tipc_bearer. Those
were used by the old broadcast implementation, and are not needed
any longer. There is no functional changes in this commit.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of variables with Hungarian notation (l_ptr, n_ptr etc.)
has been significantly reduced over the last couple of years.
We now root out the last traces of this practice.
There are no functional changes in this commit.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the previous changes in this series, we can now remove some
unused code and structures, both in the broadcast, link aggregation
and link code.
There are no functional changes in this commit.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The neighbor discovery function currently uses the function
tipc_bearer_send() for transmitting packets, assuming that the
sent buffers are not consumed by the called function.
We want to change this, in order to avoid unnecessary buffer cloning
elswhere in the code.
This commit introduces a new function tipc_bearer_skb() which consumes
the sent buffers, and let the discoverer functions use this new call
instead. The discoverer does now itself perform the cloning when
that is necessary.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we have only been supporting a fix MTU size of 1500 bytes
for all broadcast media, irrespective of their actual capability.
We now make the broadcast MTU adaptable to the carrying media, i.e.,
we use the smallest MTU supported by any of the interfaces attached
to TIPC.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, we have been keeping track of the exact set of broadcast
destinations though the help structure tipc_node_map. This leads us to
have to maintain a whole infrastructure for supporting this, including
a pseudo-bearer and a number of functions to manipulate both the bearers
and the node map correctly. Apart from the complexity, this approach is
also limiting, as struct tipc_node_map only can support cluster local
broadcast if we want to avoid it becoming excessively large. We want to
eliminate this limitation, in order to enable introduction of scoped
multicast in the future.
A closer analysis reveals that it is unnecessary maintaining this "full
set" overview; it is sufficient to keep a counter per bearer, indicating
how many nodes can be reached via this bearer at the moment. The protocol
is now robust enough to handle transitional discrepancies between the
nominal number of reachable destinations, as expected by the broadcast
protocol itself, and the number which is actually reachable at the
moment. The initial broadcast synchronization, in conjunction with the
retransmission mechanism, ensures that all packets will eventually be
acknowledged by the correct set of destinations.
This commit introduces these changes.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, message sending is performed through a deep call chain,
where the node spinlock is grabbed and held during a significant
part of the transmission time. This is clearly detrimental to
overall throughput performance; it would be better if we could send
the message after the spinlock has been released.
In this commit, we do instead let the call revert on the stack after
the buffer chain has been added to the transmission queue, whereafter
clones of the buffers are transmitted to the device layer outside the
spinlock scope.
As a further step in our effort to separate the roles of the node
and link entities we also move the function tipc_link_xmit() to
node.c, and rename it to tipc_node_xmit().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we try to add new inline functions in the code, we sometimes
run into circular include dependencies.
The main problem is that the file core.h, which really should be at
the root of the dependency chain, instead is a leaf. I.e., core.h
includes a number of header files that themselves should be allowed
to include core.h. In reality this is unnecessary, because core.h does
not need to know the full signature of any of the structs it refers to,
only their type declaration.
In this commit, we remove all dependencies from core.h towards any
other tipc header file.
As a consequence of this change, we can now move the function
tipc_own_addr(net) from addr.c to addr.h, and make it inline.
There are no functional changes in this commit.
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ip/udp bearer can be configured in a point-to-point
mode by specifying both local and remote ip/hostname,
or it can be enabled in multicast mode, where links are
established to all tipc nodes that have joined the same
multicast group. The multicast IP address is generated
based on the TIPC network ID, but can be overridden by
using another multicast address as remote ip.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the exception of infiniband media which does not use media
offsets, the media address is always located at offset 4 in the
media info field as defined by the protocol, so we move the
definition to the generic bearer.h
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TIPC_MEDIA_ADDR_SIZE and TIPC_MEDIA_ADDR_OFFSET names
are misleading, as they actually define the size and offset of
the whole media info field and not the address part. This patch
does not have any functional changes.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert TIPC_CMD_GET_MEDIA_NAMES to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a framework for transcoding legacy nl action into actions
(.doit) calls from the new nl API. This is done by converting the
incoming TLV data into netlink data with nested netlink attributes.
Unfortunately due to the randomness of the legacy API we can't do this
generically so each legacy netlink command requires a specific
transcoding recipe. In this case for bearer enable and bearer disable.
Convert TIPC_CMD_ENABLE_BEARER and TIPC_CMD_DISABLE_BEARER into doit
compat calls.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a framework for dumping netlink data from the new netlink
API and formatting it to the old legacy API format. This is done by
looping the dump data and calling a format handler for each entity, in
this case a bearer.
We dump until either all data is dumped or we reach the limited buffer
size of the legacy API. Remember, the legacy API doesn't scale.
In this commit we convert TIPC_CMD_GET_BEARER_NAMES to use the compat
layer.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC broadcast link is statically established and its relevant states
are maintained with the global variables: "bcbearer", "bclink" and
"bcl". Allowing different namespace to own different broadcast link
instances, these variables must be moved to tipc_net structure and
broadcast link instances would be allocated and initialized when
namespace is created.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bearer list defined as a global variable is used to store bearer
instances. When tipc supports net namespace, bearers created in
one namespace must be isolated with others allocated in other
namespaces, which requires us that the bearer list(bearer_list)
must be moved to tipc_net structure. As a result, a net namespace
pointer has to be passed to functions which access the bearer list.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Global variables associated with node table are below:
- node table list (node_htable)
- node hash table list (tipc_node_list)
- node table lock (node_list_lock)
- node number counter (tipc_num_nodes)
- node link number counter (tipc_num_links)
To make node table support namespace, above global variables must be
moved to tipc_net structure in order to keep secret for different
namespaces. As a consequence, these variables are allocated and
initialized when namespace is created, and deallocated when namespace
is destroyed. After the change, functions associated with these
variables have to utilize a namespace pointer to access them. So
adding namespace pointer as a parameter of these functions is the
major change made in the commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Involve namespace infrastructure, make the "tipc_net_id" global
variable aware of per namespace, and rename it to "net_id". In
order that the conversion can be successfully done, an instance
of networking namespace must be passed to relevant functions,
allowing them to access the "net_id" variable of per namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use standard SKB list APIs associated with struct sk_buff_head to
manage link's receive queue to simplify its relevant code cemplexity.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_NL_MEDIA_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
media.
Netlink logical layout of bearer set message:
-> media
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_NL_MEDIA_GET command to the new tipc netlink API.
This command supports dumping all information about all defined
media as well as getting all information about a specific media.
The information about a media includes name and link properties.
Netlink logical layout of media get response message:
-> media
-> name
-> link properties
-> tolerance
-> priority
-> window
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_NL_BEARER_SET command to the new tipc netlink API.
This command can set one or more link properties for a particular
bearer.
Netlink logical layout of bearer set message:
-> bearer
-> name
-> link properties
[ -> tolerance ]
[ -> priority ]
[ -> window ]
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_NL_BEARER_GET command to the new tipc netlink API.
This command supports dumping all data about all bearers or getting
all information about a specific bearer.
The information about a bearer includes name, link priorities and
domain.
Netlink logical layout of bearer get message:
-> bearer
-> name
Netlink logical layout of returned bearer information:
-> bearer
-> name
-> link properties
-> priority
-> tolerance
-> window
-> domain
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A new netlink API for tipc that can disable or enable a tipc bearer.
The new API is separated from the old API because of a bug in the
user space client (tipc-config). The problem is that older versions
of tipc-config has a very low receive limit and adding commands to
the legacy genl_opts struct causes the ctrl_getfamily() response
message to grow, subsequently breaking the tool.
The new API utilizes netlink policies for input validation. Where the
top-level netlink attributes are tipc-logical entities, like bearer.
The top level entities then contain nested attributes. In this case
a name, nested link properties and a domain.
Netlink commands implemented in this patch:
TIPC_NL_BEARER_ENABLE
TIPC_NL_BEARER_DISABLE
Netlink logical layout of bearer enable message:
-> bearer
-> name
[ -> domain ]
[
-> properties
-> priority
]
Netlink logical layout of bearer disable message:
-> bearer
-> name
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC currently handles two media specific addresses: Ethernet MAC
addresses and InfiniBand addresses. Those are kept in three different
formats:
1) A "raw" format as obtained from the device. This format is known
only by the media specific adapter code in eth_media.c and
ib_media.c.
2) A "generic" internal format, in the form of struct tipc_media_addr,
which can be referenced and passed around by the generic media-
unaware code.
3) A serialized version of the latter, to be conveyed in neighbor
discovery messages.
Conversion between the three formats can only be done by the media
specific code, so we have function pointers for this purpose in
struct tipc_media. Here, the media adapters can install their own
conversion functions at startup.
We now introduce a new such function, 'raw2addr()', whose purpose
is to convert from format 1 to format 2 above. We also try to as far
as possible uniform commenting, variable names and usage of these
functions, with the purpose of making them more comprehensible.
We can now also remove the function tipc_l2_media_addr_set(), whose
job is done better by the new function.
Finally, we expand the field for serialized addresses (format 3)
in discovery messages from 20 to 32 bytes. This is permitted
according to the spec, and reduces the risk of problems when we
add new media in the future.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|