Age | Commit message (Collapse) | Author | Files | Lines |
|
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
|
|
User space could send an invalid INET_DIAG_REQ_PROTOCOL attribute
as caught by syzbot.
BUG: KMSAN: uninit-value in inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
BUG: KMSAN: uninit-value in __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
CPU: 0 PID: 8505 Comm: syz-executor174 Not tainted 5.9.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x21c/0x280 lib/dump_stack.c:118
kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122
__msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219
inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
__inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
inet_diag_dump_compat+0x2a5/0x380 net/ipv4/inet_diag.c:1254
netlink_dump+0xb73/0x1cb0 net/netlink/af_netlink.c:2246
__netlink_dump_start+0xcf2/0xea0 net/netlink/af_netlink.c:2354
netlink_dump_start include/linux/netlink.h:246 [inline]
inet_diag_rcv_msg_compat+0x5da/0x6c0 net/ipv4/inet_diag.c:1288
sock_diag_rcv_msg+0x24f/0x620 net/core/sock_diag.c:256
netlink_rcv_skb+0x6d7/0x7e0 net/netlink/af_netlink.c:2470
sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
netlink_unicast+0x11c8/0x1490 net/netlink/af_netlink.c:1330
netlink_sendmsg+0x173a/0x1840 net/netlink/af_netlink.c:1919
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg net/socket.c:671 [inline]
____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
___sys_sendmsg net/socket.c:2407 [inline]
__sys_sendmsg+0x6d1/0x820 net/socket.c:2440
__do_sys_sendmsg net/socket.c:2449 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x441389
Code: e8 fc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff3b02ce98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441389
RDX: 0000000000000000 RSI: 0000000020001500 RDI: 0000000000000003
RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000402130
R13: 00000000004021c0 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline]
kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126
kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80
slab_alloc_node mm/slub.c:2907 [inline]
__kmalloc_node_track_caller+0x9aa/0x12f0 mm/slub.c:4511
__kmalloc_reserve net/core/skbuff.c:142 [inline]
__alloc_skb+0x35f/0xb30 net/core/skbuff.c:210
alloc_skb include/linux/skbuff.h:1094 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline]
netlink_sendmsg+0xdb9/0x1840 net/netlink/af_netlink.c:1894
sock_sendmsg_nosec net/socket.c:651 [inline]
sock_sendmsg net/socket.c:671 [inline]
____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
___sys_sendmsg net/socket.c:2407 [inline]
__sys_sendmsg+0x6d1/0x820 net/socket.c:2440
__do_sys_sendmsg net/socket.c:2449 [inline]
__se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
__x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: 3f935c75eb52 ("inet_diag: support for wider protocol numbers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:
=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!
Call trace:
lockdep_rcu_suspicious+0xd4/0xf8
__br_vlan_get_pvid+0xc0/0x100
br_vlan_get_pvid_rcu+0x78/0x108
The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.
I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.
Fixes: 7582f5b70f9a ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2020-09-21
this is a pull request of 38 patches for net-next.
the first 5 patches are by Colin Ian King, Alexandre Belloni and me and they
fix various spelling mistakes.
The next patch is by me and fixes the indention in the CAN raw protocol
according to the kernel coding style.
Diego Elio Pettenò contributes two patches to fix dead links in CAN's Kconfig.
Masahiro Yamada's patch removes the "WITH Linux-syscall-note" from SPDX tag of
C files.
AThe next 4 patches are by me and target the CAN device infrastructure and add
error propagation and improve the output of various messages to ease driver
development and debugging.
YueHaibing's patch for the c_can driver removes an unused inline function.
Next follows another patch by Colin Ian King, which removes the unneeded
initialization of a variable in the mcba_usb driver.
A patch by me annotates a fallthrough in the mscan driver.
The ti_hecc driver is converted to use devm_platform_ioremap_resource_byname()
in a patch by Dejin Zheng.
Liu Shixin's patch converts the pcan_usb_pro driver to make use of
le32_add_cpu() instead of open coding it.
Wang Hai's patch for the peak_pciefd_main driver removes an unused makro.
Vaibhav Gupta's patch converts the pch_can driver to generic power management.
Stephane Grosjean improves the pcan_usb usb driver by first documenting the
commands sent to the device and by adding support of rxerr/txerr counters.
The next patch is by me and cleans up the Kconfig of the CAN SPI drivers.
The next 6 patches all target the mcp251x driver, they are by Timo Schlüßler,
Andy Shevchenko, Tim Harvey and me. They update the DT bindings documentation,
sort the include files alphabetically, add GPIO support, make use of the
readx_poll_timeout() helper, and add support for half duplex SPI-controllers.
Wolfram Sang contributes a patch to update the contact email address in the
mscan driver, while Zhang Changzhong updates the clock handling.
The next patch is by and updates the rx-offload infrastructure to support
callback less usage.
The last 6 patches add support for the mcp25xxfd CAN SPI driver. First the
dt-bindings are added by Oleksij Rempel, the regmap infrastructure and the main
driver is contributed by me. Kurt Van Dijck adds listen-only support,
Manivannan Sadhasivam adds himself as maintainer, and Thomas Kopp himself as a
reviewer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
This time we have:
* some AP-side infrastructure for FILS discovery and
unsolicited probe resonses
* a major rework of the encapsulation/header conversion
offload from Felix, to fit better with e.g. AP_VLAN
interfaces
* performance fix for VHT A-MPDU size, don't limit to HT
* some initial patches for S1G (sub 1 GHz) support, more
will come in this area
* minor cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* fix using HE on 2.4 GHz
* AQL (airtime queue limit) estimation & VHT160 fix
* do not oversize A-MPDUs if local capability is smaller than peer's
* fix radiotap on 6 GHz to not put 2.4 GHz flag
* fix Kconfig for lib80211
* little fixlet for 6 GHz channel number / frequency conversion
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 37ab4fa7844a ("net: unix: allow bind to fail on mutex lock"),
the assignment to err is redundant. So remove it.
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the backlog status in not exposed to user-space.
Since long backlogs (or simply not empty ones) can be a
source of noticeable latency, -RT deployments need some way
to inspect it.
Additionally, there isn't a direct match between 'softnet_stat'
lines and the related CPU - sd for offline CPUs are not dumped -
so this patch also includes the CPU id into such entry.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "WITH Linux-syscall-note" exception is intended for UAPI headers.
See LICENSES/exceptions/Linux-syscall-note
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20200403073741.18352-1-masahiroy@kernel.org
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes the indention to follow kernel coding style.
Link: https://lore.kernel.org/r/20200915223527.1417033-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch fixes spelling erros found by "codespell" in the net/can
subtree.
Link: https://lore.kernel.org/r/20200915223527.1417033-5-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(*x),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check whether there is any hwaccel VLAN tag on RX, and if there is,
treat it as the tag_8021q header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The whole purpose of tag_8021q is to send VLAN-tagged traffic to the
CPU, from which the driver can decode the source port and switch id.
Currently this only works if the VLAN filtering on the master is
disabled. Change that by explicitly adding code to tag_8021q.c to add
the VLANs corresponding to the tags to the filter of the master
interface.
Because we now need to call vlan_vid_add, then we also need to hold the
RTNL mutex. Propagate that requirement to the callers of dsa_8021q_setup
and modify the existing call sites as appropriate. Note that one call
path, sja1105_best_effort_vlan_filtering_set -> sja1105_vlan_filtering
-> sja1105_setup_8021q_tagging, was already holding this lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most DSA switch tags shift the EtherType to the right, causing the
master to not parse the VLAN as VLAN.
However, not all switches do that (example: tail tags, tag_8021q etc),
and if the DSA master has "rx-vlan-filter: on" in ethtool -k, then we
have a problem.
Therefore, we could populate the VLAN table of the master, just in case
(for some switches it will not make a difference), so that network I/O
can work even with a VLAN filtering master.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the bridge has VLAN awareness disabled there isn't any duplication
of functionality, since the bridge does not process VLAN. Don't deny
adding 8021q uppers to DSA switch ports in that case. The switch is
supposed to simply pass traffic leaving the VLAN tag as-is, and the
stack will happily strip the VLAN tag for all 8021q uppers that exist.
We need to ensure that there are no 8021q uppers when the user attempts
to enable bridge vlan_filtering.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current logic beats me a little bit. The comment that "bridge skips
-EOPNOTSUPP, so skip the prepare phase" was introduced in commit
fb2dabad69f0 ("net: dsa: support VLAN filtering switchdev attr").
I'm not sure:
(a) ok, the bridge skips -EOPNOTSUPP, but, so what, where are we
returning -EOPNOTSUPP?
(b) even if we are, and I'm just not seeing it, what is the causality
relationship between the bridge skipping -EOPNOTSUPP and DSA
skipping the prepare phase, and just returning zero?
One thing is certain beyond doubt though, and that is that DSA currently
refuses VLAN filtering from the "commit" phase instead of "prepare", and
that this is not a good thing:
ip link add br0 type bridge
ip link add br1 type bridge vlan_filtering 1
ip link set swp2 master br0
ip link set swp3 master br1
[ 3790.379389] 001: sja1105 spi0.1: VLAN filtering is a global setting
[ 3790.379399] 001: ------------[ cut here ]------------
[ 3790.379403] 001: WARNING: CPU: 1 PID: 515 at net/switchdev/switchdev.c:157 switchdev_port_attr_set_now+0x9c/0xa4
[ 3790.379420] 001: swp3: Commit of attribute (id=6) failed.
[ 3790.379533] 001: [<c11ff588>] (switchdev_port_attr_set_now) from [<c11b62e4>] (nbp_vlan_init+0x84/0x148)
[ 3790.379544] 001: [<c11b62e4>] (nbp_vlan_init) from [<c11a2ff0>] (br_add_if+0x514/0x670)
[ 3790.379554] 001: [<c11a2ff0>] (br_add_if) from [<c1031b5c>] (do_setlink+0x38c/0xab0)
[ 3790.379565] 001: [<c1031b5c>] (do_setlink) from [<c1036fe8>] (__rtnl_newlink+0x44c/0x748)
[ 3790.379573] 001: [<c1036fe8>] (__rtnl_newlink) from [<c1037328>] (rtnl_newlink+0x44/0x60)
[ 3790.379580] 001: [<c1037328>] (rtnl_newlink) from [<c10315fc>] (rtnetlink_rcv_msg+0x124/0x2f8)
[ 3790.379590] 001: [<c10315fc>] (rtnetlink_rcv_msg) from [<c10926b8>] (netlink_rcv_skb+0xb8/0x110)
[ 3790.379806] 001: ---[ end trace 0000000000000002 ]---
[ 3790.379819] 001: sja1105 spi0.1 swp3: failed to initialize vlan filtering on this port
So move the current logic that may fail (except ds->ops->port_vlan_filtering,
that is way harder) into the prepare stage of the switchdev transaction.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PRECHANGEUPPER
This is checking for the following order of operations, and makes sure
to deny that configuration:
ip link add link swp2 name swp2.100 type vlan id 100
ip link add br0 type bridge vlan_filtering 1
ip link set swp2 master br0
bridge vlan add dev swp2 vid 100
Instead of using vlan_for_each(), which looks at the VLAN filters
installed with vlan_vid_add(), just track the 8021q uppers. This has the
advantage of freeing up the vlan_vid_add() call for actual VLAN
filtering.
There is another change in this patch. The check is moved in slave.c,
from switch.c. I don't think it makes sense to have this 8021q upper
check for each switch port that gets notified of that VLAN addition
(these include DSA links and CPU ports, we know those can't have 8021q
uppers because they don't have a net_device registered for them), so
just do it in slave.c, for that one slave interface.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA tries to prevent having a VLAN added by a bridge and by an 802.1Q
upper at the same time. It does that by checking the VID in
.ndo_vlan_rx_add_vid(), since that's something that the 8021q module
calls, via vlan_vid_add(). When a VLAN matches in both subsystems, this
check returns -EBUSY.
However the vlan_vid_add() function isn't specific to the 8021q module
in any way at all. It is simply the kernel's way to tell an interface to
add a VLAN to its RX filter and not drop that VLAN. So there's no reason
to return -EBUSY when somebody tries to call vlan_vid_add() for a VLAN
that was installed by the bridge. The proper behavior is to accept that
configuration.
So what's wrong is how DSA checks that it has an 8021q upper. It should
look at the actual uppers for that, not just assume that the 8021q
module was somewhere in the call stack of .ndo_vlan_rx_add_vid().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We'll be adding a new check in the PRECHANGEUPPER notifier, where we'll
need to check some VLAN uppers. It is hard to do that when there is
already a function named dsa_slave_upper_vlan_check. So rename this one.
Not to mention that this function probably shouldn't have started with
"dsa_slave_" in the first place, since the struct net_device argument
isn't a DSA slave, but an 8021q upper of one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There doesn't seem to be any strong technical reason for doing it this
way, but we'll be adding more checks for invalid upper device
configurations, and it will be easier to have them all grouped under
PRECHANGEUPPER.
Tested that it still works:
ip link set br0 type bridge vlan_filtering 1
ip link add link swp2 name swp2.100 type vlan id 100
ip link set swp2.100 master br0
[ 20.321312] br0: port 5(swp2.100) entered blocking state
[ 20.326711] br0: port 5(swp2.100) entered disabled state
Error: dsa_core: Cannot enslave VLAN device into VLAN aware bridge.
[ 20.346549] br0: port 5(swp2.100) entered blocking state
[ 20.351957] br0: port 5(swp2.100) entered disabled state
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When budget is non-zero, skb_unref() has already handled the
NULL checking.
When budget is zero, the dev_consume_skb_any() has handled NULL
checking in __dev_kfree_skb_irq(), or dev_kfree_skb() which also
ultimately call skb_unref().
So remove the unnecessary checking in napi_consume_skb().
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calculating ancestor_size with IPv6 enabled, simply using
sizeof(struct ipv6_pinfo) doesn't account for extra bytes needed for
alignment in the struct sctp6_sock. On x86, there aren't any extra
bytes, but on ARM the ipv6_pinfo structure is aligned on an 8-byte
boundary so there were 4 pad bytes that were omitted from the
ancestor_size calculation. This would lead to corruption of the
pd_lobby pointers, causing an oops when trying to free the sctp
structure on socket close.
Fixes: 636d25d557d1 ("sctp: not copy sctp_sock pd_lobby in sctp_copy_descendant")
Signed-off-by: Henry Ptasinski <hptasinski@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add entries for the 100base-FX full and half duplex supported modes.
$ ethtool eth0
Supported ports: [ FIBRE ]
Supported link modes: 100baseFX/Half 100baseFX/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 100baseFX/Half 100baseFX/Full
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: off
Port: MII
PHYAD: 1
Transceiver: external
Supports Wake-on: gs
Wake-on: d
SecureOn password: 00:00:00:00:00:00
Current message level: 0x00000000 (0)
Link detected: yes
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb->nh.raw has been renamed as skb->network_header in 2007, in
commit b0e380b1d8a8 ("[SK_BUFF]: unions of just one member don't get
anything done, kill them")
So here we change it to the new name.
Cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow the DSA drivers to implement the devlink call to get info info,
e.g. driver name, firmware version, ASIC ID, etc.
v2:
Combine declaration and the assignment on a single line.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow DSA drivers to make use of devlink regions, via simple wrappers.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Given a devlink instance, return the dsa switch it is associated to.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the region to be snapshotted to the function performing the
snapshot. This allows one function to operate on numerous regions.
v4:
Add missing kerneldoc for ICE
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IPV6_SEG6_HMAC is enabled and CRYPTO is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for CRYPTO_HMAC
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- IPV6_SEG6_HMAC [=y] && NET [=y] && INET [=y] && IPV6 [=y]
WARNING: unmet direct dependencies detected for CRYPTO_SHA1
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- IPV6_SEG6_HMAC [=y] && NET [=y] && INET [=y] && IPV6 [=y]
WARNING: unmet direct dependencies detected for CRYPTO_SHA256
Depends on [n]: CRYPTO [=n]
Selected by [y]:
- IPV6_SEG6_HMAC [=y] && NET [=y] && INET [=y] && IPV6 [=y]
The reason is that IPV6_SEG6_HMAC selects CRYPTO_HMAC, CRYPTO_SHA1, and
CRYPTO_SHA256 without depending on or selecting CRYPTO while those configs
are subordinate to CRYPTO.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- fix wrong type use in backbone_gw hash, by Linus Luessing
- disable TT re-routing for multicast packets, by Linus Luessing
- Add missing include for in_interrupt(), by Sven Eckelmann
- fix BLA/multicast issues for packets sent via unicast,
by Linus Luessing (3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the header file containing a function's prototype isn't included by
the sourcefile containing the associated function, the build system
complains of missing prototypes.
Fixes the following W=1 kernel build warning(s):
net/tipc/udp_media.c:446:5: warning: no previous prototype for ‘tipc_udp_nl_dump_remoteip’ [-Wmissing-prototypes]
net/tipc/udp_media.c:532:5: warning: no previous prototype for ‘tipc_udp_nl_add_bearer_data’ [-Wmissing-prototypes]
net/tipc/udp_media.c:614:5: warning: no previous prototype for ‘tipc_udp_nl_bearer_add’ [-Wmissing-prototypes]
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is no used any more, so can remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Historically L2TP core statistics count the L2TP header in the
per-session and per-tunnel byte counts tracked for transmission and
receipt.
Now that l2tp_xmit_skb updates tx stats, it is necessary for
l2tp_xmit_core to pass out the length of the transmitted packet so that
the statistics can be updated correctly.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the function ovs_ct_limit_exit, there is already a helper vaibale
which could be reused to improve the readability, so i fix it in this
patch.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/bridge/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Roopa Prabhu <roopa@nvidia.com>
Cc: Nikolay Aleksandrov <nikolay@nvidia.com>
Cc: bridge@lists.linux-foundation.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/atm/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Chas Williams <3chas3@gmail.com>
Cc: linux-atm-general@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/tipc/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/bluetooth/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/ipv6/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/rds/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Cc: linux-rdma@vger.kernel.org
Cc: rds-devel@oss.oracle.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop repeated words in net/core/.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rekeying is required for security since a key is less secure when using
for a long time. Also, key will be detached when its nonce value (or
seqno ...) is exhausted. We now make the rekeying process automatic and
configurable by user.
Basically, TIPC will at a specific interval generate a new key by using
the kernel 'Random Number Generator' cipher, then attach it as the node
TX key and securely distribute to others in the cluster as RX keys (-
the key exchange). The automatic key switching will then take over, and
make the new key active shortly. Afterwards, the traffic from this node
will be encrypted with the new session key. The same can happen in peer
nodes but not necessarily at the same time.
For simplicity, the automatically generated key will be initiated as a
per node key. It is not too hard to also support a cluster key rekeying
(e.g. a given node will generate a unique cluster key and update to the
others in the cluster...), but that doesn't bring much benefit, while a
per-node key is even more secure.
We also enable user to force a rekeying or change the rekeying interval
via netlink, the new 'set key' command option: 'TIPC_NLA_NODE_REKEYING'
is added for these purposes as follows:
- A value >= 1 will be set as the rekeying interval (in minutes);
- A value of 0 will disable the rekeying;
- A value of 'TIPC_REKEYING_NOW' (~0) will force an immediate rekeying;
The default rekeying interval is (60 * 24) minutes i.e. done every day.
There isn't any restriction for the value but user shouldn't set it too
small or too large which results in an "ineffective" rekeying (thats ok
for testing though).
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With support from the master key option in the previous commit, it
becomes easy to make frequent updates/exchanges of session keys between
authenticated cluster nodes.
Basically, there are two situations where the key exchange will take in
place:
- When a new node joins the cluster (with the master key), it will need
to get its peer's TX key, so that be able to decrypt further messages
from that peer.
- When a new session key is generated (by either user manual setting or
later automatic rekeying feature), the key will be distributed to all
peer nodes in the cluster.
A key to be exchanged is encapsulated in the data part of a 'MSG_CRYPTO
/KEY_DISTR_MSG' TIPC v2 message, then xmit-ed as usual and encrypted by
using the master key before sending out. Upon receipt of the message it
will be decrypted in the same way as regular messages, then attached as
the sender's RX key in the receiver node.
In this way, the key exchange is reliable by the link layer, as well as
security, integrity and authenticity by the crypto layer.
Also, the forward security will be easily achieved by user changing the
master key actively but this should not be required very frequently.
The key exchange feature is independent on the presence of a master key
Note however that the master key still is needed for new nodes to be
able to join the cluster. It is also optional, and can be turned off/on
via the sysfs: 'net/tipc/key_exchange_enabled' [default 1: enabled].
Backward compatibility is guaranteed because for nodes that do not have
master key support, key exchange using master key ie. tx_key = 0 if any
will be shortly discarded at the message validation step. In other
words, the key exchange feature will be automatically disabled to those
nodes.
v2: fix the "implicit declaration of function 'tipc_crypto_key_flush'"
error in node.c. The function only exists when built with the TIPC
"CONFIG_TIPC_CRYPTO" option.
v3: use 'info->extack' for a message emitted due to netlink operations
instead (- David's comment).
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In addition to the supported cluster & per-node encryption keys for the
en/decryption of TIPC messages, we now introduce one option for user to
set a cluster key as 'master key', which is simply a symmetric key like
the former but has a longer life cycle. It has two purposes:
- Authentication of new member nodes in the cluster. New nodes, having
no knowledge of current session keys in the cluster will still be
able to join the cluster as long as they know the master key. This is
because all neighbor discovery (LINK_CONFIG) messages must be
encrypted with this key.
- Encryption of session encryption keys during automatic exchange and
update of those.This is a feature we will introduce in a later commit
in this series.
We insert the new key into the currently unused slot 0 in the key array
and start using it immediately once the user has set it.
After joining, a node only knowing the master key should be fully
communicable to existing nodes in the cluster, although those nodes may
have their own session keys activated (i.e. not the master one). To
support this, we define a 'grace period', starting from the time a node
itself reports having no RX keys, so the existing nodes will use the
master key for encryption instead. The grace period can be extended but
will automatically stop after e.g. 5 seconds without a new report. This
is also the basis for later key exchanging feature as the new node will
be impossible to decrypt anything without the support from master key.
For user to set a master key, we define a new netlink flag -
'TIPC_NLA_NODE_KEY_MASTER', so it can be added to the current 'set key'
netlink command to specify the setting key to be a master key.
Above all, the traditional cluster/per-node key mechanism is guaranteed
to work when user comes not to use this master key option. This is also
compatible to legacy nodes without the feature supported.
Even this master key can be updated without any interruption of cluster
connectivity but is so is needed, this has to be coordinated and set by
the user.
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We reduce the lasting time for a pending TX key to be active as well as
for a passive RX key to be freed which generally helps speed up the key
switching. It is not expected to be too fast but should not be too slow
either. Also the key handling logic is simplified that a pending RX key
will be removed automatically if it is found not working after a number
of times; the probing for a pending TX key is now carried on a specific
message user ('LINK_PROTOCOL' or 'LINK_CONFIG') which is more efficient
than using a timer on broadcast messages, the timer is reserved for use
later as needed.
The kernel logs or 'pr***()' are now made as clear as possible to user.
Some prints are added, removed or changed to the debug-level. The
'TIPC_CRYPTO_DEBUG' definition is removed, and the 'pr_debug()' is used
instead which will be much helpful in runtime.
Besides we also optimize the code in some other places as a preparation
for later commits.
v2: silent more kernel logs, also use 'info->extack' for a message
emitted due to netlink operations instead (- David's comments).
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dev flash status notify function parameter lists are getting
rather long, so add a struct to be filled and passed rather than
continuously changing the function signatures.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a timeout element to the DEVLINK_CMD_FLASH_UPDATE_STATUS
netlink message for use by a userland utility to show that
a particular firmware flash activity may take a long but
bounded time to finish. Also add a handy helper for drivers
to make use of the new timeout value.
UI usage hints:
- if non-zero, add timeout display to the end of the status line
[component] status_msg ( Xm Ys : Am Bs )
using the timeout value for Am Bs and updating the Xm Ys
every second
- if the timeout expires while awaiting the next update,
display something like
[component] status_msg ( timeout reached : Am Bs )
- if new status notify messages are received, remove
the timeout and start over
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|