| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The ACPI nodes for CS35L56 can contain an extra I2CSerialBusV2 that
is not a real device, it is an alias address.
This alias address will not be in the cirrus,dev-index array, so reject
any instantions with a device address not found in the array.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-10-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A tuning patch is always needed to enable the ASP audio port.
If the BIOS did not patch the firmware, then it is mandatory to
have a .bin file.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-9-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A RAM firmware can only be downloaded if the CS35L56 is currently
running from ROM firmware. The driver must not try to overwrite
the RAM if the CS35L56 is already running from that RAM.
Firmware can be downloaded in these two cases:
- The BIOS has already patched the firmware (secured mode).
In this case the firmware files will only contain tunings that
are safe to overwrite.
- The CS35L56 is running the built-in ROM firmware.
After a RAM firmware has been downloaded it can only be cleared by
hard resetting CS35L56. Some systems only hard-reset during
power-on and do not give the driver control of hard reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-8-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If cs35l56_hda_fw_load() successfully called cs_dsp_power_up() the error
path must balance that with a call to cs_dsp_power_down().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-7-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In cs35l56_hda_unbind() cs_dsp_power_down() must be called to cleanup
before calling cs_dsp_remove cs_dsp_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-6-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Always call cs_dsp_power_up() and cs_dsp_run() in
cs35l56_hda_fw_load() even if there aren't any firmware files
to download. Also, if there aren't any firmware files to
download there is no need to do cs35l56_firmware_shutdown() and
cs35l56_system_reset().
If there aren't any firmware files there's no need to write
anything to the CS35L56 registers to make it work - it will
already be running the ROM firmware. So it's not strictly
necessary to start cs_dsp.
But it's perfectly ok to call cs_dsp_power_up() and
cs_dsp_run() without downloading any firmware. This avoids
having to support a state where audio is playing but cs_dsp
is not running.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-5-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When firmware is reloaded after a system resume cs_dsp_power_down() should
be called before calling cs_dsp_power_up().
The fw_patched flag should also be cleared and only set again if the
firmware download succeeded.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-4-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Only call regcache_mark_dirty() in cs35l56_hda_fw_load() if
the CS35L56 was SYSTEM_RESET.
recache_mark_dirty() changes the behaviour of regcache_sync()
to write out cache values that are not the default value, and
skip cache values that are the default.
AUDIO_REINIT does not reset the registers. regcache_mark_dirty()
after AUDIO_REINIT could cause the regcache_sync() to sync
registers incorrectly because it will assume that all registers
have reset to default.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the call to cs_dsp_run() in cs35l56_hda_fw_load() so that it
is after the CS35L56 has been reset/reinit'd and the regmap
cache has been synced.
cs_dsp_run() syncs up ALSA control cache values with the DSP memory
so this must not be done until the firmware has reinitialized.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Smatch complains that this return should be a goto:
sound/pci/hda/cs35l56_hda.c:910 cs35l56_hda_common_probe()
warn: missing unwind goto?
The goto error disables cansleep so that seems reasonable.
Fixes: 73cfbfa9caea ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/465160f4-b7cf-41d5-931e-d6c9e68fa3c7@moroto.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.6
Here's an initial batch of updates for ASoC for this release cycle.
We've got a bunch of new drivers in here, a bit of core work from
Morimoto-san and quite a lot of janitorial work. There's several
updates that pull in changes from other subsystems in order to build
on them:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes.
- Create a library function for intlog10() and use it in the NAU8825
driver.
- Include the ASoC tests, including the topology tests, in the default
KUnit full test coverage. This also involves enabling UML builds of
ALSA since that's the default KUnit test environment which pulls in
the addition of some stubs to the driver.
- More factoring out from Morimoto-san.
- Convert a lot of drivers to use the more modern maple tree register
cache.
- Support for AMD machines with MAX98388 and NAU8821, Cirrus Logic
CS35L36, Intel AVS machines with ES8336 and RT5663 and NXP i.MX93.
|
|
Currently we only mute after playback has finished, and unmute
prior to setting global enable. To prevent any possible pops
and clicks, mute at probe, and then only unmute after global
enable is set.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-12-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To ensure consistency between the HDA core and the CS35L41 HDA
driver, add a device_link between them. This ensures that the
HDA core will suspend first, and resume second, meaning the
amp driver will not miss any events from the playback hook from
the HDA core during system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-11-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In order to correctly pause audio on suspend, amps using external boost
require parts of the pause sequence to be called for all amps before moving
on to the next steps.
For example, as part of pausing the audio, the VSPK GPIO must be disabled,
but since this GPIO is controlled by one amp, but controls the boost for
all amps, it is required to separate the calls.
During playback this is achieved by using the pre and post playback hooks,
however during system suspend, this is not possible, so to separate the
calls, we use both the .prepare and .suspend calls to pause the audio.
Currently, for this reason, we do not restart audio on system resume.
However, we can support this by relying on the playback hook to resume
playback after system suspend.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-10-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use new hooks to ensure separation between play/pause actions,
as required by external boost.
External Boost on CS35L41 requires the amp to go through a
particular sequence of steps. One of these steps involes
the setting of a GPIO. This GPIO is connected to one or
more of the amps, and it may control the boost for all of
the amps. To ensure that the GPIO is set when it is safe
to do so, and to ensure that boost is ready for the rest of
the sequence to be able to continue, we must ensure that
the each part of the sequence is executed for each amp
before moving on to the next part of the sequence.
Some of the Play and Pause actions have moved from Open to
Prepare. This is because Open is not guaranteed to be called
again on system resume, whereas Prepare should.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-9-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These hooks can be used to add callbacks that would be run before and after
the main playback hooks. These hooks would be called for all amps, before
moving on to the next hook, i.e. pre_playback_hook would be called for
all amps, before the playback_hook is called for all amps, then finally
the post_playback_hook is called for all amps.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This allows play and pause to be called from multiple places,
which is necessary for system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-7-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are several steps required to put the system into system suspend.
Some of these steps may fail, so the driver should pass up the errors
if they occur.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In order to properly system suspend, it is necessary to unload the firmware
and ensure the chip is ready for shutdown (if necessary). If the system
is currently in runtime suspend, it is necessary to wake up the device,
and then make it ready. Currently, the wake does not correctly resync
the device, which may mean it cannot suspend correctly. Fix this by
performaing a resync.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently, we do not check the return status of the pause command,
immediately after we load firmware. If the pause has failed,
the firmware is not running.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To enable the speaker output in external boost mode, 2 registers must
be set, one after another. The longer the time between the writes of
the two registers, the more likely, and more loudly a pop may occur.
To minimize this, an mbox command can be used to allow the firmware
to perform this action, minimizing any delay between write, thus
minimizing any pop or click as a result. The old method will remain
when running without firmware.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a driver for the Cirrus Logic CS35L56 amplifier. This uses the same
component binding API as the CS35L41 driver. This is not a standalone
HDA device; it provides control of the CS35L56 for systems that use a
combination of an HDA codec and CS35L56 amplifiers with audio routed
through the HDA codec.
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Control interfaces are I2C or SPI through the standard Linux I2C or SPI
bus framework.
Most chip functionality is controlled by on-board ROM firmware that is
always running. Firmware patches can be applied by the driver in the form
of a .wmfw file (firmware patch) and/or a .bin file (system tuning).
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add #includes of dependencies into hda_auto_parser.h and hda_generic.h
hda_auto_parser.h uses definitions in hda_local.h.
hda_generic.h uses definitions in hda_local.h and hda_auto_parser.h.
It also references struct hda_jack_callback, but only as a pointer.
This has been forward-declared so hda_jack.h only needs to be
included in source that actually uses it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add HDMI codec ID for Intel Lunar Lake platform.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230721135722.31288-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Switch order of Intel MTL and RPL codec entries to keep the codec device
id list nicely ordered. Also use the opportunity to fix the naming
to the convention used elsewhere in the drivers.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230721135722.31288-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Also, handle the errors from the helper more properly instead of
silently ignoring.
The code changes the call order of snd_ctl_add() of the vmaster object
and its followers for avoiding the possible memory leaks at error
path. But there should be no difference in the functionality.
Link: https://lore.kernel.org/r/20230721071643.3631-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Also, handle the errors from the helper more properly instead of
silently ignoring.
Link: https://lore.kernel.org/r/20230721071643.3631-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Except for a debug print, there should be no functional change.
Link: https://lore.kernel.org/r/20230721071643.3631-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Also, add the missing NULL checks in psc724_set_jack_state() to deal
with error cases.
Link: https://lore.kernel.org/r/20230720082108.31346-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Link: https://lore.kernel.org/r/20230720082108.31346-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Adding support for new Dell laptops using Cirrus Logic CS35L41
smart amplifiers with Realtek codec.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230720082022.13033-2-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Generic fixup for CS35L41 amplifies should not have vendor specific
chained fixup. For ThinkPad laptops with led issue, we can just add
specific fixup.
Fixes: a6ac60b36dade (ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec)
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230720082022.13033-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ALSA: Make control API taking controls_rwsem consistently
A few ALSA control API helpers like snd_ctl_rename(), snd_ctl_remove()
and snd_ctl_find_*() suppose the callers taking card->controls_rwsem.
But it's error-prone and fragile. This patch set tries to change
those API functions to take the card->controls>rwsem internally by
themselves, so that the drivers don't need to take care of lockings.
After applying this patch set, only a couple of places still touch
card->controls_rwsem (which are OK-ish as they need for traversing the
control linked list).
Link: https://lore.kernel.org/r/20230718141304.1032-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Now that snd_ctl_find_id() takes the locking itself, we can get rid of
the messy locking in the caller side in snd_emu10k1_verify_controls().
Link: https://lore.kernel.org/r/20230718141304.1032-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
For reducing the unnecessary use of controls_rwsem in the drivers,
this patch adds a new variant for snd_ctl_find_*() helpers:
snd_ctl_find_id_locked() and snd_ctl_find_numid_locked() look for a
kctl element inside the card->controls_rwsem -- that is, doing the
very same as what snd_ctl_find_id() and snd_ctl_find_numid() did until
now. snd_ctl_find_id() and snd_ctl_find_numid() remain same,
i.e. still unlocked version, but they will be switched to locked
version once after all callers are replaced.
The patch also replaces the calls of snd_ctl_find_id() and
snd_ctl_find_numid() in a few places; all of those are places where we
know that the functions are called properly with controls_rwsem held.
All others are without rwsem (although they should have been).
After this patch, we'll turn on the locking in snd_ctl_find_id() and
snd_ctl_find_numid() to be more race-free.
Link: https://lore.kernel.org/r/20230718141304.1032-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
So far, snd_ctl_remove() requires its caller to take
card->controls_rwsem manually before the call for avoiding possible
races. However, many callers don't care and miss the locking.
Basically it's cumbersome and error-prone to enforce it to each
caller. Moreover, card->controls_rwsem is a field that should be used
only by internal or proper helpers, and it's not to be touched at
random external places.
This patch is an attempt to make those calls more consistent: now
snd_ctl_remove() takes the card->controls_rwsem internally, just like
other API functions for kctls. Since a few callers already take the
controls_rwsem locks, the patch removes those locks at the same time,
too.
Link: https://lore.kernel.org/r/20230718141304.1032-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The HP Laptop 15s-eq2xxx uses ALC236 codec and controls the mute LED using
COEF 0x07 index 1. No existing quirk covers this configuration.
Adds a new quirk and enables it for the device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230718161241.393181-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixes headset detection on Clevo NS70AU.
Co-developed-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230718145722.10592-1-wse@tuxedocomputers.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Pull cleanup of HD-audio PCI IDs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use PCI device IDs from pci_ids.h header and while at it to simplify
declarations change to using PCI_DEVICE_DATA() macro for Intel IDs and
PCI_VDEVICE() for all other that have defined vendor.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-11-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of using local macro to match PCI device, use global one. As
Apollolake is Broxton-P successor that made it to the market, be precise
and use APL shortcut.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-7-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Current code references 0x1a98 which is BXT-M (not -T as it is
commented) and it's an RVP, BXT-M B0 to be specific. From what we know
no BXT is available on market.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
- Remove the "log-like" parts, following the same logic as the previous
commit
- Unify format
- Add missing major contributors, including myself
- Sort entries in order of first contribution (Creative comes last for
optical reasons; they don't appear to have directly contributed
anyway)
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
