| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add support to configure the GPIO pin to the specific configuration.
The GPIO pin can be configured as GPO, IRQ, SDOUT2, PDMCLK, MICBASE_EN,
GPI, MCLK, SDIN, PDMDIN1, PDMDIN2, PDMDIN3 or PDMDIN4 and the output
drive can be configured with various configuration.
Signed-off-by: Camel Guo <camelg@axis.com>
Link: https://lore.kernel.org/r/20200918114025.18205-2-camel.guo@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add code to allow the ASI Tx output to be placed into High-z mode
during unused ASI cycles. This allows for other devices that may be on
the bus to drive the ASI out. By default the 320adcx140 sends 0's for
unused cycles.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-4-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It was observed that if the device was active and register writes were
performed there were some unwanted behaviors particularly when writing
the word length and some filter options. So when writing to the device
the device should be placed in sleep mode and then exit sleep mode once
the register update is complete.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200915190606.1744-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add General Purpose Output (GPO) configuration and driver output
configuration. The GPOs can be configured as a GPO, IRQ, SDOUT or a
PDMCLK output. In addition the output drive can be configured with
various configurations.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200728160833.24130-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200719153822.59788-1-grandmaster@al2klimov.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support to configure the GPI pins to the specific configuration.
The pins can be disabled or be configured as data input for any of the
digital mic channels. In addition the GPI can be used a a general
purpose input, a Master clock input or an ASI input for daisy chaining
devices.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200526200917.10385-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-5.8
|
|
Configure the PDM sampling edges based on the values from the firmware.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200514123338.20392-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The device tree binding declares the ti,mic-bias-source and the
ti,vref-source properties as u32. The code reads them as u8 which is
incorrect. Since the device tree binding indicates them as u32 the
conde needs to be updated to read u32.
In addition the bias source needs to be shifted 4 bits to
correctly write the register.
driver family")
Fixes: 37bde5acf040 ("ASoC: tlv320adcx140: Add the tlv320adcx140 codec
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200513142807.11802-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The TLV320ADCx140 parts support Dynamic Range Enhancer (DRE) as defined
in Section 8.3.2 of the data sheets.
The DRE achieves a complete-channel dynamic range as high as 120 dB.
At a system level, the DRE scheme enables far-field, high-fidelity recording
of audio signals in very quiet environments and low-distortion recording in
loud environments.
There are 2 enables for DRE. The first is a global setting that enables
the DRE engine in the device and the other enable is per channel. If
the DRE is enabled globally then either DRE or AGC can be used per each
configured channel. If global DRE is disabled then even setting the DRE
enable bit in the channel config register will have no effect.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200221181358.22526-1-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the tlv320adcx140 codec driver family.
The TLV320ADCx140 is a Burr-Brown™ highperformance, audio analog-to-digital
converter (ADC) that supports simultaneous sampling of up to four analog
channels or eight digital channels for the pulse density modulation (PDM)
microphone input. The device supports line and microphone inputs, and
allows for both single-ended and differential input configurations.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200220210759.31466-3-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
