#!/bin/bash # SPDX-License-Identifier: GPL-2.0 # # Copyright (c) 2019 David Ahern . All rights reserved. # # IPv4 and IPv6 functional tests focusing on VRF and routing lookups # for various permutations: # 1. icmp, tcp, udp and netfilter # 2. client, server, no-server # 3. global address on interface # 4. global address on 'lo' # 5. remote and local traffic # 6. VRF and non-VRF permutations # # Setup: # ns-A | ns-B # No VRF case: # [ lo ] [ eth1 ]---|---[ eth1 ] [ lo ] # remote address # VRF case: # [ red ]---[ eth1 ]---|---[ eth1 ] [ lo ] # # ns-A: # eth1: 172.16.1.1/24, 2001:db8:1::1/64 # lo: 127.0.0.1/8, ::1/128 # 172.16.2.1/32, 2001:db8:2::1/128 # red: 127.0.0.1/8, ::1/128 # 172.16.3.1/32, 2001:db8:3::1/128 # # ns-B: # eth1: 172.16.1.2/24, 2001:db8:1::2/64 # lo2: 127.0.0.1/8, ::1/128 # 172.16.2.2/32, 2001:db8:2::2/128 # # ns-A to ns-C connection - only for VRF and same config # as ns-A to ns-B # # server / client nomenclature relative to ns-A # Kselftest framework requirement - SKIP code is 4. ksft_skip=4 VERBOSE=0 NSA_DEV=eth1 NSA_DEV2=eth2 NSB_DEV=eth1 NSC_DEV=eth2 VRF=red VRF_TABLE=1101 # IPv4 config NSA_IP=172.16.1.1 NSB_IP=172.16.1.2 VRF_IP=172.16.3.1 NS_NET=172.16.1.0/24 # IPv6 config NSA_IP6=2001:db8:1::1 NSB_IP6=2001:db8:1::2 VRF_IP6=2001:db8:3::1 NS_NET6=2001:db8:1::/120 NSA_LO_IP=172.16.2.1 NSB_LO_IP=172.16.2.2 NSA_LO_IP6=2001:db8:2::1 NSB_LO_IP6=2001:db8:2::2 # non-local addresses for freebind tests NL_IP=172.17.1.1 NL_IP6=2001:db8:4::1 MD5_PW=abc123 MD5_WRONG_PW=abc1234 MCAST=ff02::1 # set after namespace create NSA_LINKIP6= NSB_LINKIP6= NSA=ns-A NSB=ns-B NSC=ns-C NSA_CMD="ip netns exec ${NSA}" NSB_CMD="ip netns exec ${NSB}" NSC_CMD="ip netns exec ${NSC}" which ping6 > /dev/null 2>&1 && ping6=$(which ping6) || ping6=$(which ping) ################################################################################ # utilities log_test() { local rc=$1 local expected=$2 local msg="$3" [ "${VERBOSE}" = "1" ] && echo if [ ${rc} -eq ${expected} ]; then nsuccess=$((nsuccess+1)) printf "TEST: %-70s [ OK ]\n" "${msg}" else nfail=$((nfail+1)) printf "TEST: %-70s [FAIL]\n" "${msg}" if [ "${PAUSE_ON_FAIL}" = "yes" ]; then echo echo "hit enter to continue, 'q' to quit" read a [ "$a" = "q" ] && exit 1 fi fi if [ "${PAUSE}" = "yes" ]; then echo echo "hit enter to continue, 'q' to quit" read a [ "$a" = "q" ] && exit 1 fi kill_procs } log_test_addr() { local addr=$1 local rc=$2 local expected=$3 local msg="$4" local astr astr=$(addr2str ${addr}) log_test $rc $expected "$msg - ${astr}" } log_section() { echo echo "###########################################################################" echo "$*" echo "###########################################################################" echo } log_subsection() { echo echo "#################################################################" echo "$*" echo } log_start() { # make sure we have no test instances running kill_procs if [ "${VERBOSE}" = "1" ]; then echo echo "#######################################################" fi } log_debug() { if [ "${VERBOSE}" = "1" ]; then echo echo "$*" echo fi } show_hint() { if [ "${VERBOSE}" = "1" ]; then echo "HINT: $*" echo fi } kill_procs() { killall nettest ping ping6 >/dev/null 2>&1 sleep 1 } do_run_cmd() { local cmd="$*" local out if [ "$VERBOSE" = "1" ]; then echo "COMMAND: ${cmd}" fi out=$($cmd 2>&1) rc=$? if [ "$VERBOSE" = "1" -a -n "$out" ]; then echo "$out" fi return $rc } run_cmd() { do_run_cmd ${NSA_CMD} $* } run_cmd_nsb() { do_run_cmd ${NSB_CMD} $* } run_cmd_nsc() { do_run_cmd ${NSC_CMD} $* } setup_cmd() { local cmd="$*" local rc run_cmd ${cmd} rc=$? if [ $rc -ne 0 ]; then # show user the command if not done so already if [ "$VERBOSE" = "0" ]; then echo "setup command: $cmd" fi echo "failed. stopping tests" if [ "${PAUSE_ON_FAIL}" = "yes" ]; then echo echo "hit enter to continue" read a fi exit $rc fi } setup_cmd_nsb() { local cmd="$*" local rc run_cmd_nsb ${cmd} rc=$? if [ $rc -ne 0 ]; then # show user the command if not done so already if [ "$VERBOSE" = "0" ]; then echo "setup command: $cmd" fi echo "failed. stopping tests" if [ "${PAUSE_ON_FAIL}" = "yes" ]; then echo echo "hit enter to continue" read a fi exit $rc fi } setup_cmd_nsc() { local cmd="$*" local rc run_cmd_nsc ${cmd} rc=$? if [ $rc -ne 0 ]; then # show user the command if not done so already if [ "$VERBOSE" = "0" ]; then echo "setup command: $cmd" fi echo "failed. stopping tests" if [ "${PAUSE_ON_FAIL}" = "yes" ]; then echo echo "hit enter to continue" read a fi exit $rc fi } # set sysctl values in NS-A set_sysctl() { echo "SYSCTL: $*" echo run_cmd sysctl -q -w $* } # get sysctl values in NS-A get_sysctl() { ${NSA_CMD} sysctl -n $* } ################################################################################ # Setup for tests addr2str() { case "$1" in 127.0.0.1) echo "loopback";; ::1) echo "IPv6 loopback";; ${NSA_IP}) echo "ns-A IP";; ${NSA_IP6}) echo "ns-A IPv6";; ${NSA_LO_IP}) echo "ns-A loopback IP";; ${NSA_LO_IP6}) echo "ns-A loopback IPv6";; ${NSA_LINKIP6}|${NSA_LINKIP6}%*) echo "ns-A IPv6 LLA";; ${NSB_IP}) echo "ns-B IP";; ${NSB_IP6}) echo "ns-B IPv6";; ${NSB_LO_IP}) echo "ns-B loopback IP";; ${NSB_LO_IP6}) echo "ns-B loopback IPv6";; ${NSB_LINKIP6}|${NSB_LINKIP6}%*) echo "ns-B IPv6 LLA";; ${NL_IP}) echo "nonlocal IP";; ${NL_IP6}) echo "nonlocal IPv6";; ${VRF_IP}) echo "VRF IP";; ${VRF_IP6}) echo "VRF IPv6";; ${MCAST}%*) echo "multicast IP";; *) echo "unknown";; esac } get_linklocal() { local ns=$1 local dev=$2 local addr addr=$(ip -netns ${ns} -6 -br addr show dev ${dev} | \ awk '{ for (i = 3; i <= NF; ++i) { if ($i ~ /^fe80/) print $i } }' ) addr=${addr/\/*} [ -z "$addr" ] && return 1 echo $addr return 0 } ################################################################################ # create namespaces and vrf create_vrf() { local ns=$1 local vrf=$2 local table=$3 local addr=$4 local addr6=$5 ip -netns ${ns} link add ${vrf} type vrf table ${table} ip -netns ${ns} link set ${vrf} up ip -netns ${ns} route add vrf ${vrf} unreachable default metric 8192 ip -netns ${ns} -6 route add vrf ${vrf} unreachable default metric 8192 ip -netns ${ns} addr add 127.0.0.1/8 dev ${vrf} ip -netns ${ns} -6 addr add ::1 dev ${vrf} nodad if [ "${addr}" != "-" ]; then ip -netns ${ns} addr add dev ${vrf} ${addr} fi if [ "${addr6}" != "-" ]; then ip -netns ${ns} -6 addr add dev ${vrf} ${addr6} fi ip -netns ${ns} ru del pref 0 ip -netns ${ns} ru add pref 32765 from all lookup local ip -netns ${ns} -6 ru del pref 0 ip -netns ${ns} -6 ru add pref 32765 from all lookup local } create_ns() { local ns=$1 local addr=$2 local addr6=$3 ip netns add ${ns} ip -netns ${ns} link set lo up if [ "${addr}" != "-" ]; then ip -netns ${ns} addr add dev lo ${addr} fi if [ "${addr6}" != "-" ]; then ip -netns ${ns} -6 addr add dev lo ${addr6} fi ip -netns ${ns} ro add unreachable default metric 8192 ip -netns ${ns} -6 ro add unreachable default metric 8192 ip netns exec ${ns} sysctl -qw net.ipv4.ip_forward=1 ip netns exec ${ns} sysctl -qw net.ipv6.conf.all.keep_addr_on_down=1 ip netns exec ${ns} sysctl -qw net.ipv6.conf.all.forwarding=1 ip netns exec ${ns} sysctl -qw net.ipv6.conf.default.forwarding=1 } # create veth pair to connect namespaces and apply addresses. connect_ns() { local ns1=$1 local ns1_dev=$2 local ns1_addr=$3 local ns1_addr6=$4 local ns2=$5 local ns2_dev=$6 local ns2_addr=$7 local ns2_addr6=$8 ip -netns ${ns1} li add ${ns1_dev} type veth peer name tmp ip -netns ${ns1} li set ${ns1_dev} up ip -netns ${ns1} li set tmp netns ${ns2} name ${ns2_dev} ip -netns ${ns2} li set ${ns2_dev} up if [ "${ns1_addr}" != "-" ]; then ip -netns ${ns1} addr add dev ${ns1_dev} ${ns1_addr} ip -netns ${ns2} addr add dev ${ns2_dev} ${ns2_addr} fi if [ "${ns1_addr6}" != "-" ]; then ip -netns ${ns1} addr add dev ${ns1_dev} ${ns1_addr6} ip -netns ${ns2} addr add dev ${ns2_dev} ${ns2_addr6} fi } cleanup() { # explicit cleanups to check those code paths ip netns | grep -q ${NSA} if [ $? -eq 0 ]; then ip -netns ${NSA} link delete ${VRF} ip -netns ${NSA} ro flush table ${VRF_TABLE} ip -netns ${NSA} addr flush dev ${NSA_DEV} ip -netns ${NSA} -6 addr flush dev ${NSA_DEV} ip -netns ${NSA} link set dev ${NSA_DEV} down ip -netns ${NSA} link del dev ${NSA_DEV} ip netns pids ${NSA} | xargs kill 2>/dev/null ip netns del ${NSA} fi ip netns pids ${NSB} | xargs kill 2>/dev/null ip netns del ${NSB} ip netns pids ${NSC} | xargs kill 2>/dev/null ip netns del ${NSC} >/dev/null 2>&1 } cleanup_vrf_dup() { ip link del ${NSA_DEV2} >/dev/null 2>&1 ip netns pids ${NSC} | xargs kill 2>/dev/null ip netns del ${NSC} >/dev/null 2>&1 } setup_vrf_dup() { # some VRF tests use ns-C which has the same config as # ns-B but for a device NOT in the VRF create_ns ${NSC} "-" "-" connect_ns ${NSA} ${NSA_DEV2} ${NSA_IP}/24 ${NSA_IP6}/64 \ ${NSC} ${NSC_DEV} ${NSB_IP}/24 ${NSB_IP6}/64 } setup() { local with_vrf=${1} # make sure we are starting with a clean slate kill_procs cleanup 2>/dev/null log_debug "Configuring network namespaces" set -e create_ns ${NSA} ${NSA_LO_IP}/32 ${NSA_LO_IP6}/128 create_ns ${NSB} ${NSB_LO_IP}/32 ${NSB_LO_IP6}/128 connect_ns ${NSA} ${NSA_DEV} ${NSA_IP}/24 ${NSA_IP6}/64 \ ${NSB} ${NSB_DEV} ${NSB_IP}/24 ${NSB_IP6}/64 NSA_LINKIP6=$(get_linklocal ${NSA} ${NSA_DEV}) NSB_LINKIP6=$(get_linklocal ${NSB} ${NSB_DEV}) # tell ns-A how to get to remote addresses of ns-B if [ "${with_vrf}" = "yes" ]; then create_vrf ${NSA} ${VRF} ${VRF_TABLE} ${VRF_IP} ${VRF_IP6} ip -netns ${NSA} link set dev ${NSA_DEV} vrf ${VRF} ip -netns ${NSA} ro add vrf ${VRF} ${NSB_LO_IP}/32 via ${NSB_IP} dev ${NSA_DEV} ip -netns ${NSA} -6 ro add vrf ${VRF} ${NSB_LO_IP6}/128 via ${NSB_IP6} dev ${NSA_DEV} ip -netns ${NSB} ro add ${VRF_IP}/32 via ${NSA_IP} dev ${NSB_DEV} ip -netns ${NSB} -6 ro add ${VRF_IP6}/128 via ${NSA_IP6} dev ${NSB_DEV} else ip -netns ${NSA} ro add ${NSB_LO_IP}/32 via ${NSB_IP} dev ${NSA_DEV} ip -netns ${NSA} ro add ${NSB_LO_IP6}/128 via ${NSB_IP6} dev ${NSA_DEV} fi # tell ns-B how to get to remote addresses of ns-A ip -netns ${NSB} ro add ${NSA_LO_IP}/32 via ${NSA_IP} dev ${NSB_DEV} ip -netns ${NSB} ro add ${NSA_LO_IP6}/128 via ${NSA_IP6} dev ${NSB_DEV} set +e sleep 1 } setup_lla_only() { # make sure we are starting with a clean slate kill_procs cleanup 2>/dev/null log_debug "Configuring network namespaces" set -e create_ns ${NSA} "-" "-" create_ns ${NSB} "-" "-" create_ns ${NSC} "-" "-" connect_ns ${NSA} ${NSA_DEV} "-" "-" \ ${NSB} ${NSB_DEV} "-" "-" connect_ns ${NSA} ${NSA_DEV2} "-" "-" \ ${NSC} ${NSC_DEV} "-" "-" NSA_LINKIP6=$(get_linklocal ${NSA} ${NSA_DEV}) NSB_LINKIP6=$(get_linklocal ${NSB} ${NSB_DEV}) NSC_LINKIP6=$(get_linklocal ${NSC} ${NSC_DEV}) create_vrf ${NSA} ${VRF} ${VRF_TABLE} "-" "-" ip -netns ${NSA} link set dev ${NSA_DEV} vrf ${VRF} ip -netns ${NSA} link set dev ${NSA_DEV2} vrf ${VRF} set +e sleep 1 } ################################################################################ # IPv4 ipv4_ping_novrf() { local a # # out # for a in ${NSB_IP} ${NSB_LO_IP} do log_start run_cmd ping -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping out" log_start run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping out, device bind" log_start run_cmd ping -c1 -w1 -I ${NSA_LO_IP} ${a} log_test_addr ${a} $? 0 "ping out, address bind" done # # in # for a in ${NSA_IP} ${NSA_LO_IP} do log_start run_cmd_nsb ping -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping in" done # # local traffic # for a in ${NSA_IP} ${NSA_LO_IP} 127.0.0.1 do log_start run_cmd ping -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping local" done # # local traffic, socket bound to device # # address on device a=${NSA_IP} log_start run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping local, device bind" # loopback addresses not reachable from device bind # fails in a really weird way though because ipv4 special cases # route lookups with oif set. for a in ${NSA_LO_IP} 127.0.0.1 do log_start show_hint "Fails since address on loopback device is out of device scope" run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 1 "ping local, device bind" done # # ip rule blocks reachability to remote address # log_start setup_cmd ip rule add pref 32765 from all lookup local setup_cmd ip rule del pref 0 from all lookup local setup_cmd ip rule add pref 50 to ${NSB_LO_IP} prohibit setup_cmd ip rule add pref 51 from ${NSB_IP} prohibit a=${NSB_LO_IP} run_cmd ping -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, blocked by rule" # NOTE: ipv4 actually allows the lookup to fail and yet still create # a viable rtable if the oif (e.g., bind to device) is set, so this # case succeeds despite the rule # run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} a=${NSA_LO_IP} log_start show_hint "Response generates ICMP (or arp request is ignored) due to ip rule" run_cmd_nsb ping -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, blocked by rule" [ "$VERBOSE" = "1" ] && echo setup_cmd ip rule del pref 32765 from all lookup local setup_cmd ip rule add pref 0 from all lookup local setup_cmd ip rule del pref 50 to ${NSB_LO_IP} prohibit setup_cmd ip rule del pref 51 from ${NSB_IP} prohibit # # route blocks reachability to remote address # log_start setup_cmd ip route replace unreachable ${NSB_LO_IP} setup_cmd ip route replace unreachable ${NSB_IP} a=${NSB_LO_IP} run_cmd ping -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, blocked by route" # NOTE: ipv4 actually allows the lookup to fail and yet still create # a viable rtable if the oif (e.g., bind to device) is set, so this # case succeeds despite not having a route for the address # run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} a=${NSA_LO_IP} log_start show_hint "Response is dropped (or arp request is ignored) due to ip route" run_cmd_nsb ping -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, blocked by route" # # remove 'remote' routes; fallback to default # log_start setup_cmd ip ro del ${NSB_LO_IP} a=${NSB_LO_IP} run_cmd ping -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, unreachable default route" # NOTE: ipv4 actually allows the lookup to fail and yet still create # a viable rtable if the oif (e.g., bind to device) is set, so this # case succeeds despite not having a route for the address # run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} } ipv4_ping_vrf() { local a # should default on; does not exist on older kernels set_sysctl net.ipv4.raw_l3mdev_accept=1 2>/dev/null # # out # for a in ${NSB_IP} ${NSB_LO_IP} do log_start run_cmd ping -c1 -w1 -I ${VRF} ${a} log_test_addr ${a} $? 0 "ping out, VRF bind" log_start run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping out, device bind" log_start run_cmd ip vrf exec ${VRF} ping -c1 -w1 -I ${NSA_IP} ${a} log_test_addr ${a} $? 0 "ping out, vrf device + dev address bind" log_start run_cmd ip vrf exec ${VRF} ping -c1 -w1 -I ${VRF_IP} ${a} log_test_addr ${a} $? 0 "ping out, vrf device + vrf address bind" done # # in # for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd_nsb ping -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping in" done # # local traffic, local address # for a in ${NSA_IP} ${VRF_IP} 127.0.0.1 do log_start show_hint "Source address should be ${a}" run_cmd ping -c1 -w1 -I ${VRF} ${a} log_test_addr ${a} $? 0 "ping local, VRF bind" done # # local traffic, socket bound to device # # address on device a=${NSA_IP} log_start run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping local, device bind" # vrf device is out of scope for a in ${VRF_IP} 127.0.0.1 do log_start show_hint "Fails since address on vrf device is out of device scope" run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 1 "ping local, device bind" done # # ip rule blocks address # log_start setup_cmd ip rule add pref 50 to ${NSB_LO_IP} prohibit setup_cmd ip rule add pref 51 from ${NSB_IP} prohibit a=${NSB_LO_IP} run_cmd ping -c1 -w1 -I ${VRF} ${a} log_test_addr ${a} $? 2 "ping out, vrf bind, blocked by rule" log_start run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, blocked by rule" a=${NSA_LO_IP} log_start show_hint "Response lost due to ip rule" run_cmd_nsb ping -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, blocked by rule" [ "$VERBOSE" = "1" ] && echo setup_cmd ip rule del pref 50 to ${NSB_LO_IP} prohibit setup_cmd ip rule del pref 51 from ${NSB_IP} prohibit # # remove 'remote' routes; fallback to default # log_start setup_cmd ip ro del vrf ${VRF} ${NSB_LO_IP} a=${NSB_LO_IP} run_cmd ping -c1 -w1 -I ${VRF} ${a} log_test_addr ${a} $? 2 "ping out, vrf bind, unreachable route" log_start run_cmd ping -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, unreachable route" a=${NSA_LO_IP} log_start show_hint "Response lost by unreachable route" run_cmd_nsb ping -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, unreachable route" } ipv4_ping() { log_section "IPv4 ping" log_subsection "No VRF" setup set_sysctl net.ipv4.raw_l3mdev_accept=0 2>/dev/null ipv4_ping_novrf setup set_sysctl net.ipv4.raw_l3mdev_accept=1 2>/dev/null ipv4_ping_novrf log_subsection "With VRF" setup "yes" ipv4_ping_vrf } ################################################################################ # IPv4 TCP # # MD5 tests without VRF # ipv4_tcp_md5_novrf() { # # single address # # basic use case log_start run_cmd nettest -s -M ${MD5_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: Single address config" # client sends MD5, server not configured log_start show_hint "Should timeout due to MD5 mismatch" run_cmd nettest -s & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: Server no config, client uses password" # wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -s -M ${MD5_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: Client uses wrong password" # client from different address log_start show_hint "Should timeout due to MD5 mismatch" run_cmd nettest -s -M ${MD5_PW} -m ${NSB_LO_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: Client address does not match address configured with password" # # MD5 extension - prefix length # # client in prefix log_start run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: Prefix config" # client in prefix, wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: Prefix config, client uses wrong password" # client outside of prefix log_start show_hint "Should timeout due to MD5 mismatch" run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -c ${NSB_LO_IP} -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: Prefix config, client address not in configured prefix" } # # MD5 tests with VRF # ipv4_tcp_md5() { # # single address # # basic use case log_start run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Single address config" # client sends MD5, server not configured log_start show_hint "Should timeout since server does not have MD5 auth" run_cmd nettest -s -I ${VRF} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Server no config, client uses password" # wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Client uses wrong password" # client from different address log_start show_hint "Should timeout since server config differs from client" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_LO_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Client address does not match address configured with password" # # MD5 extension - prefix length # # client in prefix log_start run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Prefix config" # client in prefix, wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Prefix config, client uses wrong password" # client outside of prefix log_start show_hint "Should timeout since client address is outside of prefix" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -c ${NSB_LO_IP} -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Prefix config, client address not in configured prefix" # # duplicate config between default VRF and a VRF # log_start run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Single address config in default VRF and VRF, conn in VRF" log_start run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsc nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 0 "MD5: VRF: Single address config in default VRF and VRF, conn in default VRF" log_start show_hint "Should timeout since client in default VRF uses VRF password" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsc nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Single address config in default VRF and VRF, conn in default VRF with VRF pw" log_start show_hint "Should timeout since client in VRF uses default VRF password" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NSB_IP} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Single address config in default VRF and VRF, conn in VRF with default VRF pw" log_start run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Prefix config in default VRF and VRF, conn in VRF" log_start run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NS_NET} & sleep 1 run_cmd_nsc nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 0 "MD5: VRF: Prefix config in default VRF and VRF, conn in default VRF" log_start show_hint "Should timeout since client in default VRF uses VRF password" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NS_NET} & sleep 1 run_cmd_nsc nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Prefix config in default VRF and VRF, conn in default VRF with VRF pw" log_start show_hint "Should timeout since client in VRF uses default VRF password" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} & run_cmd nettest -s -M ${MD5_WRONG_PW} -m ${NS_NET} & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Prefix config in default VRF and VRF, conn in VRF with default VRF pw" # # negative tests # log_start run_cmd nettest -s -I ${NSA_DEV} -M ${MD5_PW} -m ${NSB_IP} log_test $? 1 "MD5: VRF: Device must be a VRF - single address" log_start run_cmd nettest -s -I ${NSA_DEV} -M ${MD5_PW} -m ${NS_NET} log_test $? 1 "MD5: VRF: Device must be a VRF - prefix" test_ipv4_md5_vrf__vrf_server__no_bind_ifindex test_ipv4_md5_vrf__global_server__bind_ifindex0 } test_ipv4_md5_vrf__vrf_server__no_bind_ifindex() { log_start show_hint "Simulates applications using VRF without TCP_MD5SIG_FLAG_IFINDEX" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} --no-bind-key-ifindex & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: VRF-bound server, unbound key accepts connection" log_start show_hint "Binding both the socket and the key is not required but it works" run_cmd nettest -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET} --force-bind-key-ifindex & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: VRF-bound server, bound key accepts connection" } test_ipv4_md5_vrf__global_server__bind_ifindex0() { # This particular test needs tcp_l3mdev_accept=1 for Global server to accept VRF connections local old_tcp_l3mdev_accept old_tcp_l3mdev_accept=$(get_sysctl net.ipv4.tcp_l3mdev_accept) set_sysctl net.ipv4.tcp_l3mdev_accept=1 log_start run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} --force-bind-key-ifindex & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Global server, Key bound to ifindex=0 rejects VRF connection" log_start run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} --force-bind-key-ifindex & sleep 1 run_cmd_nsc nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Global server, key bound to ifindex=0 accepts non-VRF connection" log_start run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} --no-bind-key-ifindex & sleep 1 run_cmd_nsb nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Global server, key not bound to ifindex accepts VRF connection" log_start run_cmd nettest -s -M ${MD5_PW} -m ${NS_NET} --no-bind-key-ifindex & sleep 1 run_cmd_nsc nettest -r ${NSA_IP} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Global server, key not bound to ifindex accepts non-VRF connection" # restore value set_sysctl net.ipv4.tcp_l3mdev_accept="$old_tcp_l3mdev_accept" } ipv4_tcp_novrf() { local a # # server tests # for a in ${NSA_IP} ${NSA_LO_IP} do log_start run_cmd nettest -s & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "Global server" done a=${NSA_IP} log_start run_cmd nettest -s -I ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "Device server" # verify TCP reset sent and received for a in ${NSA_IP} ${NSA_LO_IP} do log_start show_hint "Should fail 'Connection refused' since there is no server" run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 1 "No server" done # # client # for a in ${NSB_IP} ${NSB_LO_IP} do log_start run_cmd_nsb nettest -s & sleep 1 run_cmd nettest -r ${a} -0 ${NSA_IP} log_test_addr ${a} $? 0 "Client" log_start run_cmd_nsb nettest -s & sleep 1 run_cmd nettest -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 0 "Client, device bind" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -r ${a} log_test_addr ${a} $? 1 "No server, unbound client" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "No server, device client" done # # local address tests # for a in ${NSA_IP} ${NSA_LO_IP} 127.0.0.1 do log_start run_cmd nettest -s & sleep 1 run_cmd nettest -r ${a} -0 ${a} -1 ${a} log_test_addr ${a} $? 0 "Global server, local connection" done a=${NSA_IP} log_start run_cmd nettest -s -I ${NSA_DEV} & sleep 1 run_cmd nettest -r ${a} -0 ${a} log_test_addr ${a} $? 0 "Device server, unbound client, local connection" for a in ${NSA_LO_IP} 127.0.0.1 do log_start show_hint "Should fail 'Connection refused' since addresses on loopback are out of device scope" run_cmd nettest -s -I ${NSA_DEV} & sleep 1 run_cmd nettest -r ${a} log_test_addr ${a} $? 1 "Device server, unbound client, local connection" done a=${NSA_IP} log_start run_cmd nettest -s & sleep 1 run_cmd nettest -r ${a} -0 ${a} -d ${NSA_DEV} log_test_addr ${a} $? 0 "Global server, device client, local connection" for a in ${NSA_LO_IP} 127.0.0.1 do log_start show_hint "Should fail 'No route to host' since addresses on loopback are out of device scope" run_cmd nettest -s & sleep 1 run_cmd nettest -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "Global server, device client, local connection" done a=${NSA_IP} log_start run_cmd nettest -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -d ${NSA_DEV} -r ${a} -0 ${a} log_test_addr ${a} $? 0 "Device server, device client, local connection" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 1 "No server, device client, local conn" ipv4_tcp_md5_novrf } ipv4_tcp_vrf() { local a # disable global server log_subsection "Global server disabled" set_sysctl net.ipv4.tcp_l3mdev_accept=0 # # server tests # for a in ${NSA_IP} ${VRF_IP} do log_start show_hint "Should fail 'Connection refused' since global server with VRF is disabled" run_cmd nettest -s & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 1 "Global server" log_start run_cmd nettest -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "VRF server" log_start run_cmd nettest -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "Device server" # verify TCP reset received log_start show_hint "Should fail 'Connection refused' since there is no server" run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 1 "No server" done # local address tests # (${VRF_IP} and 127.0.0.1 both timeout) a=${NSA_IP} log_start show_hint "Should fail 'Connection refused' since global server with VRF is disabled" run_cmd nettest -s & sleep 1 run_cmd nettest -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "Global server, local connection" # run MD5 tests setup_vrf_dup ipv4_tcp_md5 cleanup_vrf_dup # # enable VRF global server # log_subsection "VRF Global server enabled" set_sysctl net.ipv4.tcp_l3mdev_accept=1 for a in ${NSA_IP} ${VRF_IP} do log_start show_hint "client socket should be bound to VRF" run_cmd nettest -s -3 ${VRF} & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "Global server" log_start show_hint "client socket should be bound to VRF" run_cmd nettest -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "VRF server" # verify TCP reset received log_start show_hint "Should fail 'Connection refused'" run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 1 "No server" done a=${NSA_IP} log_start show_hint "client socket should be bound to device" run_cmd nettest -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 0 "Device server" # local address tests for a in ${NSA_IP} ${VRF_IP} do log_start show_hint "Should fail 'Connection refused' since client is not bound to VRF" run_cmd nettest -s -I ${VRF} & sleep 1 run_cmd nettest -r ${a} log_test_addr ${a} $? 1 "Global server, local connection" done # # client # for a in ${NSB_IP} ${NSB_LO_IP} do log_start run_cmd_nsb nettest -s & sleep 1 run_cmd nettest -r ${a} -d ${VRF} log_test_addr ${a} $? 0 "Client, VRF bind" log_start run_cmd_nsb nettest -s & sleep 1 run_cmd nettest -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 0 "Client, device bind" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -r ${a} -d ${VRF} log_test_addr ${a} $? 1 "No server, VRF client" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "No server, device client" done for a in ${NSA_IP} ${VRF_IP} 127.0.0.1 do log_start run_cmd nettest -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd nettest -r ${a} -d ${VRF} -0 ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local connection" done a=${NSA_IP} log_start run_cmd nettest -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd nettest -r ${a} -d ${NSA_DEV} -0 ${a} log_test_addr ${a} $? 0 "VRF server, device client, local connection" log_start show_hint "Should fail 'No route to host' since client is out of VRF scope" run_cmd nettest -s -I ${VRF} & sleep 1 run_cmd nettest -r ${a} log_test_addr ${a} $? 1 "VRF server, unbound client, local connection" log_start run_cmd nettest -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -r ${a} -d ${VRF} -0 ${a} log_test_addr ${a} $? 0 "Device server, VRF client, local connection" log_start run_cmd nettest -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -r ${a} -d ${NSA_DEV} -0 ${a} log_test_addr ${a} $? 0 "Device server, device client, local connection" } ipv4_tcp() { log_section "IPv4/TCP" log_subsection "No VRF" setup # tcp_l3mdev_accept should have no affect without VRF; # run tests with it enabled and disabled to verify log_subsection "tcp_l3mdev_accept disabled" set_sysctl net.ipv4.tcp_l3mdev_accept=0 ipv4_tcp_novrf log_subsection "tcp_l3mdev_accept enabled" set_sysctl net.ipv4.tcp_l3mdev_accept=1 ipv4_tcp_novrf log_subsection "With VRF" setup "yes" ipv4_tcp_vrf } ################################################################################ # IPv4 UDP ipv4_udp_novrf() { local a # # server tests # for a in ${NSA_IP} ${NSA_LO_IP} do log_start run_cmd nettest -D -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "Global server" log_start show_hint "Should fail 'Connection refused' since there is no server" run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 1 "No server" done a=${NSA_IP} log_start run_cmd nettest -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "Device server" # # client # for a in ${NSB_IP} ${NSB_LO_IP} do log_start run_cmd_nsb nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -0 ${NSA_IP} log_test_addr ${a} $? 0 "Client" log_start run_cmd_nsb nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -d ${NSA_DEV} -0 ${NSA_IP} log_test_addr ${a} $? 0 "Client, device bind" log_start run_cmd_nsb nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -d ${NSA_DEV} -C -0 ${NSA_IP} log_test_addr ${a} $? 0 "Client, device send via cmsg" log_start run_cmd_nsb nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -d ${NSA_DEV} -S -0 ${NSA_IP} log_test_addr ${a} $? 0 "Client, device bind via IP_UNICAST_IF" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -D -r ${a} log_test_addr ${a} $? 1 "No server, unbound client" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -D -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "No server, device client" done # # local address tests # for a in ${NSA_IP} ${NSA_LO_IP} 127.0.0.1 do log_start run_cmd nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -0 ${a} -1 ${a} log_test_addr ${a} $? 0 "Global server, local connection" done a=${NSA_IP} log_start run_cmd nettest -s -D -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -r ${a} log_test_addr ${a} $? 0 "Device server, unbound client, local connection" for a in ${NSA_LO_IP} 127.0.0.1 do log_start show_hint "Should fail 'Connection refused' since address is out of device scope" run_cmd nettest -s -D -I ${NSA_DEV} & sleep 1 run_cmd nettest -D -r ${a} log_test_addr ${a} $? 1 "Device server, unbound client, local connection" done a=${NSA_IP} log_start run_cmd nettest -s -D & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Global server, device client, local connection" log_start run_cmd nettest -s -D & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -C -r ${a} log_test_addr ${a} $? 0 "Global server, device send via cmsg, local connection" log_start run_cmd nettest -s -D & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -S -r ${a} log_test_addr ${a} $? 0 "Global server, device client via IP_UNICAST_IF, local connection" # IPv4 with device bind has really weird behavior - it overrides the # fib lookup, generates an rtable and tries to send the packet. This # causes failures for local traffic at different places for a in ${NSA_LO_IP} 127.0.0.1 do log_start show_hint "Should fail since addresses on loopback are out of device scope" run_cmd nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 2 "Global server, device client, local connection" log_start show_hint "Should fail since addresses on loopback are out of device scope" run_cmd nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -d ${NSA_DEV} -C log_test_addr ${a} $? 1 "Global server, device send via cmsg, local connection" log_start show_hint "Should fail since addresses on loopback are out of device scope" run_cmd nettest -D -s & sleep 1 run_cmd nettest -D -r ${a} -d ${NSA_DEV} -S log_test_addr ${a} $? 1 "Global server, device client via IP_UNICAST_IF, local connection" done a=${NSA_IP} log_start run_cmd nettest -D -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -r ${a} -0 ${a} log_test_addr ${a} $? 0 "Device server, device client, local conn" log_start run_cmd nettest -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 2 "No server, device client, local conn" } ipv4_udp_vrf() { local a # disable global server log_subsection "Global server disabled" set_sysctl net.ipv4.udp_l3mdev_accept=0 # # server tests # for a in ${NSA_IP} ${VRF_IP} do log_start show_hint "Fails because ingress is in a VRF and global server is disabled" run_cmd nettest -D -s & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 1 "Global server" log_start run_cmd nettest -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "VRF server" log_start run_cmd nettest -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "Enslaved device server" log_start show_hint "Should fail 'Connection refused' since there is no server" run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 1 "No server" log_start show_hint "Should fail 'Connection refused' since global server is out of scope" run_cmd nettest -D -s & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 1 "Global server, VRF client, local connection" done a=${NSA_IP} log_start run_cmd nettest -s -D -I ${VRF} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local conn" log_start run_cmd nettest -s -D -I ${VRF} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "VRF server, enslaved device client, local connection" a=${NSA_IP} log_start run_cmd nettest -s -D -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Enslaved device server, VRF client, local conn" log_start run_cmd nettest -s -D -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Enslaved device server, device client, local conn" # enable global server log_subsection "Global server enabled" set_sysctl net.ipv4.udp_l3mdev_accept=1 # # server tests # for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest -D -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "Global server" log_start run_cmd nettest -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "VRF server" log_start run_cmd nettest -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 0 "Enslaved device server" log_start show_hint "Should fail 'Connection refused'" run_cmd_nsb nettest -D -r ${a} log_test_addr ${a} $? 1 "No server" done # # client tests # log_start run_cmd_nsb nettest -D -s & sleep 1 run_cmd nettest -d ${VRF} -D -r ${NSB_IP} -1 ${NSA_IP} log_test $? 0 "VRF client" log_start run_cmd_nsb nettest -D -s & sleep 1 run_cmd nettest -d ${NSA_DEV} -D -r ${NSB_IP} -1 ${NSA_IP} log_test $? 0 "Enslaved device client" # negative test - should fail log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -D -d ${VRF} -r ${NSB_IP} log_test $? 1 "No server, VRF client" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -D -d ${NSA_DEV} -r ${NSB_IP} log_test $? 1 "No server, enslaved device client" # # local address tests # a=${NSA_IP} log_start run_cmd nettest -D -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Global server, VRF client, local conn" log_start run_cmd nettest -s -D -I ${VRF} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local conn" log_start run_cmd nettest -s -D -I ${VRF} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "VRF server, device client, local conn" log_start run_cmd nettest -s -D -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Enslaved device server, VRF client, local conn" log_start run_cmd nettest -s -D -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Enslaved device server, device client, local conn" for a in ${VRF_IP} 127.0.0.1 do log_start run_cmd nettest -D -s -3 ${VRF} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Global server, VRF client, local conn" done for a in ${VRF_IP} 127.0.0.1 do log_start run_cmd nettest -s -D -I ${VRF} -3 ${VRF} & sleep 1 run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local conn" done # negative test - should fail # verifies ECONNREFUSED for a in ${NSA_IP} ${VRF_IP} 127.0.0.1 do log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -D -d ${VRF} -r ${a} log_test_addr ${a} $? 1 "No server, VRF client, local conn" done } ipv4_udp() { log_section "IPv4/UDP" log_subsection "No VRF" setup # udp_l3mdev_accept should have no affect without VRF; # run tests with it enabled and disabled to verify log_subsection "udp_l3mdev_accept disabled" set_sysctl net.ipv4.udp_l3mdev_accept=0 ipv4_udp_novrf log_subsection "udp_l3mdev_accept enabled" set_sysctl net.ipv4.udp_l3mdev_accept=1 ipv4_udp_novrf log_subsection "With VRF" setup "yes" ipv4_udp_vrf } ################################################################################ # IPv4 address bind # # verifies ability or inability to bind to an address / device ipv4_addr_bind_novrf() { # # raw socket # for a in ${NSA_IP} ${NSA_LO_IP} do log_start run_cmd nettest -s -R -P icmp -l ${a} -b log_test_addr ${a} $? 0 "Raw socket bind to local address" log_start run_cmd nettest -s -R -P icmp -l ${a} -I ${NSA_DEV} -b log_test_addr ${a} $? 0 "Raw socket bind to local address after device bind" done # # raw socket with nonlocal bind # a=${NL_IP} log_start run_cmd nettest -s -R -P icmp -f -l ${a} -I ${NSA_DEV} -b log_test_addr ${a} $? 0 "Raw socket bind to nonlocal address after device bind" # # tcp sockets # a=${NSA_IP} log_start run_cmd nettest -c ${a} -r ${NSB_IP} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address" log_start run_cmd nettest -c ${a} -r ${NSB_IP} -d ${NSA_DEV} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address after device bind" # Sadly, the kernel allows binding a socket to a device and then # binding to an address not on the device. The only restriction # is that the address is valid in the L3 domain. So this test # passes when it really should not #a=${NSA_LO_IP} #log_start #show_hint "Should fail with 'Cannot assign requested address'" #run_cmd nettest -s -l ${a} -I ${NSA_DEV} -t1 -b #log_test_addr ${a} $? 1 "TCP socket bind to out of scope local address" } ipv4_addr_bind_vrf() { # # raw socket # for a in ${NSA_IP} ${VRF_IP} do log_start show_hint "Socket not bound to VRF, but address is in VRF" run_cmd nettest -s -R -P icmp -l ${a} -b log_test_addr ${a} $? 1 "Raw socket bind to local address" log_start run_cmd nettest -s -R -P icmp -l ${a} -I ${NSA_DEV} -b log_test_addr ${a} $? 0 "Raw socket bind to local address after device bind" log_start run_cmd nettest -s -R -P icmp -l ${a} -I ${VRF} -b log_test_addr ${a} $? 0 "Raw socket bind to local address after VRF bind" done a=${NSA_LO_IP} log_start show_hint "Address on loopback is out of VRF scope" run_cmd nettest -s -R -P icmp -l ${a} -I ${VRF} -b log_test_addr ${a} $? 1 "Raw socket bind to out of scope address after VRF bind" # # raw socket with nonlocal bind # a=${NL_IP} log_start run_cmd nettest -s -R -P icmp -f -l ${a} -I ${VRF} -b log_test_addr ${a} $? 0 "Raw socket bind to nonlocal address after VRF bind" # # tcp sockets # for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest -s -l ${a} -I ${VRF} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address" log_start run_cmd nettest -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address after device bind" done a=${NSA_LO_IP} log_start show_hint "Address on loopback out of scope for VRF" run_cmd nettest -s -l ${a} -I ${VRF} -t1 -b log_test_addr ${a} $? 1 "TCP socket bind to invalid local address for VRF" log_start show_hint "Address on loopback out of scope for device in VRF" run_cmd nettest -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 1 "TCP socket bind to invalid local address for device bind" } ipv4_addr_bind() { log_section "IPv4 address binds" log_subsection "No VRF" setup ipv4_addr_bind_novrf log_subsection "With VRF" setup "yes" ipv4_addr_bind_vrf } ################################################################################ # IPv4 runtime tests ipv4_rt() { local desc="$1" local varg="$2" local with_vrf="yes" local a # # server tests # for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest ${varg} -s & sleep 1 run_cmd_nsb nettest ${varg} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, global server" setup ${with_vrf} done for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest ${varg} -s -I ${VRF} & sleep 1 run_cmd_nsb nettest ${varg} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF server" setup ${with_vrf} done a=${NSA_IP} log_start run_cmd nettest ${varg} -s -I ${NSA_DEV} & sleep 1 run_cmd_nsb nettest ${varg} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, enslaved device server" setup ${with_vrf} # # client test # log_start run_cmd_nsb nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${VRF} -r ${NSB_IP} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF client" setup ${with_vrf} log_start run_cmd_nsb nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${NSB_IP} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, enslaved device client" setup ${with_vrf} # # local address tests # for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${VRF} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, global server, VRF client, local" setup ${with_vrf} done for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest ${varg} -I ${VRF} -s & sleep 1 run_cmd nettest ${varg} -d ${VRF} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF server and client, local" setup ${with_vrf} done a=${NSA_IP} log_start run_cmd nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, global server, enslaved device client, local" setup ${with_vrf} log_start run_cmd nettest ${varg} -I ${VRF} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF server, enslaved device client, local" setup ${with_vrf} log_start run_cmd nettest ${varg} -I ${NSA_DEV} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, enslaved device server and client, local" } ipv4_ping_rt() { local with_vrf="yes" local a for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd_nsb ping -f ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "Device delete with active traffic - ping in" setup ${with_vrf} done a=${NSB_IP} log_start run_cmd ping -f -I ${VRF} ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "Device delete with active traffic - ping out" } ipv4_runtime() { log_section "Run time tests - ipv4" setup "yes" ipv4_ping_rt setup "yes" ipv4_rt "TCP active socket" "-n -1" setup "yes" ipv4_rt "TCP passive socket" "-i" } ################################################################################ # IPv6 ipv6_ping_novrf() { local a # should not have an impact, but make a known state set_sysctl net.ipv4.raw_l3mdev_accept=0 2>/dev/null # # out # for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} ${MCAST}%${NSA_DEV} do log_start run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping out" done for a in ${NSB_IP6} ${NSB_LO_IP6} do log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping out, device bind" log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_LO_IP6} ${a} log_test_addr ${a} $? 0 "ping out, loopback address bind" done # # in # for a in ${NSA_IP6} ${NSA_LO_IP6} ${NSA_LINKIP6}%${NSB_DEV} ${MCAST}%${NSB_DEV} do log_start run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping in" done # # local traffic, local address # for a in ${NSA_IP6} ${NSA_LO_IP6} ::1 ${NSA_LINKIP6}%${NSA_DEV} ${MCAST}%${NSA_DEV} do log_start run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping local, no bind" done for a in ${NSA_IP6} ${NSA_LINKIP6}%${NSA_DEV} ${MCAST}%${NSA_DEV} do log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping local, device bind" done for a in ${NSA_LO_IP6} ::1 do log_start show_hint "Fails since address on loopback is out of device scope" run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping local, device bind" done # # ip rule blocks address # log_start setup_cmd ip -6 rule add pref 32765 from all lookup local setup_cmd ip -6 rule del pref 0 from all lookup local setup_cmd ip -6 rule add pref 50 to ${NSB_LO_IP6} prohibit setup_cmd ip -6 rule add pref 51 from ${NSB_IP6} prohibit a=${NSB_LO_IP6} run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, blocked by rule" log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, blocked by rule" a=${NSA_LO_IP6} log_start show_hint "Response lost due to ip rule" run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, blocked by rule" setup_cmd ip -6 rule add pref 0 from all lookup local setup_cmd ip -6 rule del pref 32765 from all lookup local setup_cmd ip -6 rule del pref 50 to ${NSB_LO_IP6} prohibit setup_cmd ip -6 rule del pref 51 from ${NSB_IP6} prohibit # # route blocks reachability to remote address # log_start setup_cmd ip -6 route del ${NSB_LO_IP6} setup_cmd ip -6 route add unreachable ${NSB_LO_IP6} metric 10 setup_cmd ip -6 route add unreachable ${NSB_IP6} metric 10 a=${NSB_LO_IP6} run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, blocked by route" log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, blocked by route" a=${NSA_LO_IP6} log_start show_hint "Response lost due to ip route" run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, blocked by route" # # remove 'remote' routes; fallback to default # log_start setup_cmd ip -6 ro del unreachable ${NSB_LO_IP6} setup_cmd ip -6 ro del unreachable ${NSB_IP6} a=${NSB_LO_IP6} run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, unreachable route" log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, unreachable route" } ipv6_ping_vrf() { local a # should default on; does not exist on older kernels set_sysctl net.ipv4.raw_l3mdev_accept=1 2>/dev/null # # out # for a in ${NSB_IP6} ${NSB_LO_IP6} do log_start run_cmd ${ping6} -c1 -w1 -I ${VRF} ${a} log_test_addr ${a} $? 0 "ping out, VRF bind" done for a in ${NSB_LINKIP6}%${VRF} ${MCAST}%${VRF} do log_start show_hint "Fails since VRF device does not support linklocal or multicast" run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping out, VRF bind" done for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} ${MCAST}%${NSA_DEV} do log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping out, device bind" done for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} do log_start run_cmd ip vrf exec ${VRF} ${ping6} -c1 -w1 -I ${VRF_IP6} ${a} log_test_addr ${a} $? 0 "ping out, vrf device+address bind" done # # in # for a in ${NSA_IP6} ${VRF_IP6} ${NSA_LINKIP6}%${NSB_DEV} ${MCAST}%${NSB_DEV} do log_start run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 0 "ping in" done a=${NSA_LO_IP6} log_start show_hint "Fails since loopback address is out of VRF scope" run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in" # # local traffic, local address # for a in ${NSA_IP6} ${VRF_IP6} ::1 do log_start show_hint "Source address should be ${a}" run_cmd ${ping6} -c1 -w1 -I ${VRF} ${a} log_test_addr ${a} $? 0 "ping local, VRF bind" done for a in ${NSA_IP6} ${NSA_LINKIP6}%${NSA_DEV} ${MCAST}%${NSA_DEV} do log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 0 "ping local, device bind" done # LLA to GUA - remove ipv6 global addresses from ns-B setup_cmd_nsb ip -6 addr del ${NSB_IP6}/64 dev ${NSB_DEV} setup_cmd_nsb ip -6 addr del ${NSB_LO_IP6}/128 dev lo setup_cmd_nsb ip -6 ro add ${NSA_IP6}/128 via ${NSA_LINKIP6} dev ${NSB_DEV} for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd_nsb ${ping6} -c1 -w1 ${NSA_IP6} log_test_addr ${a} $? 0 "ping in, LLA to GUA" done setup_cmd_nsb ip -6 ro del ${NSA_IP6}/128 via ${NSA_LINKIP6} dev ${NSB_DEV} setup_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV} setup_cmd_nsb ip -6 addr add ${NSB_LO_IP6}/128 dev lo # # ip rule blocks address # log_start setup_cmd ip -6 rule add pref 50 to ${NSB_LO_IP6} prohibit setup_cmd ip -6 rule add pref 51 from ${NSB_IP6} prohibit a=${NSB_LO_IP6} run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, blocked by rule" log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, blocked by rule" a=${NSA_LO_IP6} log_start show_hint "Response lost due to ip rule" run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 1 "ping in, blocked by rule" log_start setup_cmd ip -6 rule del pref 50 to ${NSB_LO_IP6} prohibit setup_cmd ip -6 rule del pref 51 from ${NSB_IP6} prohibit # # remove 'remote' routes; fallback to default # log_start setup_cmd ip -6 ro del ${NSB_LO_IP6} vrf ${VRF} a=${NSB_LO_IP6} run_cmd ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping out, unreachable route" log_start run_cmd ${ping6} -c1 -w1 -I ${NSA_DEV} ${a} log_test_addr ${a} $? 2 "ping out, device bind, unreachable route" ip -netns ${NSB} -6 ro del ${NSA_LO_IP6} a=${NSA_LO_IP6} log_start run_cmd_nsb ${ping6} -c1 -w1 ${a} log_test_addr ${a} $? 2 "ping in, unreachable route" } ipv6_ping() { log_section "IPv6 ping" log_subsection "No VRF" setup ipv6_ping_novrf log_subsection "With VRF" setup "yes" ipv6_ping_vrf } ################################################################################ # IPv6 TCP # # MD5 tests without VRF # ipv6_tcp_md5_novrf() { # # single address # # basic use case log_start run_cmd nettest -6 -s -M ${MD5_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 0 "MD5: Single address config" # client sends MD5, server not configured log_start show_hint "Should timeout due to MD5 mismatch" run_cmd nettest -6 -s & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: Server no config, client uses password" # wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -6 -s -M ${MD5_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: Client uses wrong password" # client from different address log_start show_hint "Should timeout due to MD5 mismatch" run_cmd nettest -6 -s -M ${MD5_PW} -m ${NSB_LO_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: Client address does not match address configured with password" # # MD5 extension - prefix length # # client in prefix log_start run_cmd nettest -6 -s -M ${MD5_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 0 "MD5: Prefix config" # client in prefix, wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -6 -s -M ${MD5_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: Prefix config, client uses wrong password" # client outside of prefix log_start show_hint "Should timeout due to MD5 mismatch" run_cmd nettest -6 -s -M ${MD5_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -c ${NSB_LO_IP6} -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: Prefix config, client address not in configured prefix" } # # MD5 tests with VRF # ipv6_tcp_md5() { # # single address # # basic use case log_start run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Single address config" # client sends MD5, server not configured log_start show_hint "Should timeout since server does not have MD5 auth" run_cmd nettest -6 -s -I ${VRF} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Server no config, client uses password" # wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Client uses wrong password" # client from different address log_start show_hint "Should timeout since server config differs from client" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_LO_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Client address does not match address configured with password" # # MD5 extension - prefix length # # client in prefix log_start run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Prefix config" # client in prefix, wrong password log_start show_hint "Should timeout since client uses wrong password" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Prefix config, client uses wrong password" # client outside of prefix log_start show_hint "Should timeout since client address is outside of prefix" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -c ${NSB_LO_IP6} -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Prefix config, client address not in configured prefix" # # duplicate config between default VRF and a VRF # log_start run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Single address config in default VRF and VRF, conn in VRF" log_start run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsc nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 0 "MD5: VRF: Single address config in default VRF and VRF, conn in default VRF" log_start show_hint "Should timeout since client in default VRF uses VRF password" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsc nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Single address config in default VRF and VRF, conn in default VRF with VRF pw" log_start show_hint "Should timeout since client in VRF uses default VRF password" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NSB_IP6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NSB_IP6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Single address config in default VRF and VRF, conn in VRF with default VRF pw" log_start run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 0 "MD5: VRF: Prefix config in default VRF and VRF, conn in VRF" log_start run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsc nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 0 "MD5: VRF: Prefix config in default VRF and VRF, conn in default VRF" log_start show_hint "Should timeout since client in default VRF uses VRF password" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsc nettest -6 -r ${NSA_IP6} -X ${MD5_PW} log_test $? 2 "MD5: VRF: Prefix config in default VRF and VRF, conn in default VRF with VRF pw" log_start show_hint "Should timeout since client in VRF uses default VRF password" run_cmd nettest -6 -s -I ${VRF} -M ${MD5_PW} -m ${NS_NET6} & run_cmd nettest -6 -s -M ${MD5_WRONG_PW} -m ${NS_NET6} & sleep 1 run_cmd_nsb nettest -6 -r ${NSA_IP6} -X ${MD5_WRONG_PW} log_test $? 2 "MD5: VRF: Prefix config in default VRF and VRF, conn in VRF with default VRF pw" # # negative tests # log_start run_cmd nettest -6 -s -I ${NSA_DEV} -M ${MD5_PW} -m ${NSB_IP6} log_test $? 1 "MD5: VRF: Device must be a VRF - single address" log_start run_cmd nettest -6 -s -I ${NSA_DEV} -M ${MD5_PW} -m ${NS_NET6} log_test $? 1 "MD5: VRF: Device must be a VRF - prefix" } ipv6_tcp_novrf() { local a # # server tests # for a in ${NSA_IP6} ${NSA_LO_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start run_cmd nettest -6 -s & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "Global server" done # verify TCP reset received for a in ${NSA_IP6} ${NSA_LO_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start show_hint "Should fail 'Connection refused'" run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 1 "No server" done # # client # for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} do log_start run_cmd_nsb nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} log_test_addr ${a} $? 0 "Client" done for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} do log_start run_cmd_nsb nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 0 "Client, device bind" done for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} do log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "No server, device client" done # # local address tests # for a in ${NSA_IP6} ${NSA_LO_IP6} ::1 do log_start run_cmd nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} log_test_addr ${a} $? 0 "Global server, local connection" done a=${NSA_IP6} log_start run_cmd nettest -6 -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -r ${a} -0 ${a} log_test_addr ${a} $? 0 "Device server, unbound client, local connection" for a in ${NSA_LO_IP6} ::1 do log_start show_hint "Should fail 'Connection refused' since addresses on loopback are out of device scope" run_cmd nettest -6 -s -I ${NSA_DEV} & sleep 1 run_cmd nettest -6 -r ${a} log_test_addr ${a} $? 1 "Device server, unbound client, local connection" done a=${NSA_IP6} log_start run_cmd nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} -0 ${a} log_test_addr ${a} $? 0 "Global server, device client, local connection" for a in ${NSA_LO_IP6} ::1 do log_start show_hint "Should fail 'Connection refused' since addresses on loopback are out of device scope" run_cmd nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "Global server, device client, local connection" done for a in ${NSA_IP6} ${NSA_LINKIP6} do log_start run_cmd nettest -6 -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Device server, device client, local conn" done for a in ${NSA_IP6} ${NSA_LINKIP6} do log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 1 "No server, device client, local conn" done ipv6_tcp_md5_novrf } ipv6_tcp_vrf() { local a # disable global server log_subsection "Global server disabled" set_sysctl net.ipv4.tcp_l3mdev_accept=0 # # server tests # for a in ${NSA_IP6} ${VRF_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start show_hint "Should fail 'Connection refused' since global server with VRF is disabled" run_cmd nettest -6 -s & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 1 "Global server" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "VRF server" done # link local is always bound to ingress device a=${NSA_LINKIP6}%${NSB_DEV} log_start run_cmd nettest -6 -s -I ${VRF} -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "VRF server" for a in ${NSA_IP6} ${VRF_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start run_cmd nettest -6 -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "Device server" done # verify TCP reset received for a in ${NSA_IP6} ${VRF_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start show_hint "Should fail 'Connection refused'" run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 1 "No server" done # local address tests a=${NSA_IP6} log_start show_hint "Should fail 'Connection refused' since global server with VRF is disabled" run_cmd nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "Global server, local connection" # run MD5 tests setup_vrf_dup ipv6_tcp_md5 cleanup_vrf_dup # # enable VRF global server # log_subsection "VRF Global server enabled" set_sysctl net.ipv4.tcp_l3mdev_accept=1 for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s -3 ${VRF} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "Global server" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "VRF server" done # For LLA, child socket is bound to device a=${NSA_LINKIP6}%${NSB_DEV} log_start run_cmd nettest -6 -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "Global server" log_start run_cmd nettest -6 -s -I ${VRF} -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "VRF server" for a in ${NSA_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start run_cmd nettest -6 -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 0 "Device server" done # verify TCP reset received for a in ${NSA_IP6} ${VRF_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start show_hint "Should fail 'Connection refused'" run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 1 "No server" done # local address tests for a in ${NSA_IP6} ${VRF_IP6} do log_start show_hint "Fails 'Connection refused' since client is not in VRF" run_cmd nettest -6 -s -I ${VRF} & sleep 1 run_cmd nettest -6 -r ${a} log_test_addr ${a} $? 1 "Global server, local connection" done # # client # for a in ${NSB_IP6} ${NSB_LO_IP6} do log_start run_cmd_nsb nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${VRF} log_test_addr ${a} $? 0 "Client, VRF bind" done a=${NSB_LINKIP6} log_start show_hint "Fails since VRF device does not allow linklocal addresses" run_cmd_nsb nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${VRF} log_test_addr ${a} $? 1 "Client, VRF bind" for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6} do log_start run_cmd_nsb nettest -6 -s & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 0 "Client, device bind" done for a in ${NSB_IP6} ${NSB_LO_IP6} do log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -r ${a} -d ${VRF} log_test_addr ${a} $? 1 "No server, VRF client" done for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6} do log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "No server, device client" done for a in ${NSA_IP6} ${VRF_IP6} ::1 do log_start run_cmd nettest -6 -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd nettest -6 -r ${a} -d ${VRF} -0 ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local connection" done a=${NSA_IP6} log_start run_cmd nettest -6 -s -I ${VRF} -3 ${VRF} & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} -0 ${a} log_test_addr ${a} $? 0 "VRF server, device client, local connection" a=${NSA_IP6} log_start show_hint "Should fail since unbound client is out of VRF scope" run_cmd nettest -6 -s -I ${VRF} & sleep 1 run_cmd nettest -6 -r ${a} log_test_addr ${a} $? 1 "VRF server, unbound client, local connection" log_start run_cmd nettest -6 -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -r ${a} -d ${VRF} -0 ${a} log_test_addr ${a} $? 0 "Device server, VRF client, local connection" for a in ${NSA_IP6} ${NSA_LINKIP6} do log_start run_cmd nettest -6 -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -r ${a} -d ${NSA_DEV} -0 ${a} log_test_addr ${a} $? 0 "Device server, device client, local connection" done } ipv6_tcp() { log_section "IPv6/TCP" log_subsection "No VRF" setup # tcp_l3mdev_accept should have no affect without VRF; # run tests with it enabled and disabled to verify log_subsection "tcp_l3mdev_accept disabled" set_sysctl net.ipv4.tcp_l3mdev_accept=0 ipv6_tcp_novrf log_subsection "tcp_l3mdev_accept enabled" set_sysctl net.ipv4.tcp_l3mdev_accept=1 ipv6_tcp_novrf log_subsection "With VRF" setup "yes" ipv6_tcp_vrf } ################################################################################ # IPv6 UDP ipv6_udp_novrf() { local a # # server tests # for a in ${NSA_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start run_cmd nettest -6 -D -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Global server" log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Device server" done a=${NSA_LO_IP6} log_start run_cmd nettest -6 -D -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Global server" # should fail since loopback address is out of scope for a device # bound server, but it does not - hence this is more documenting # behavior. #log_start #show_hint "Should fail since loopback address is out of scope" #run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & #sleep 1 #run_cmd_nsb nettest -6 -D -r ${a} #log_test_addr ${a} $? 1 "Device server" # negative test - should fail for a in ${NSA_IP6} ${NSA_LO_IP6} ${NSA_LINKIP6}%${NSB_DEV} do log_start show_hint "Should fail 'Connection refused' since there is no server" run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 1 "No server" done # # client # for a in ${NSB_IP6} ${NSB_LO_IP6} ${NSB_LINKIP6}%${NSA_DEV} do log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -0 ${NSA_IP6} log_test_addr ${a} $? 0 "Client" log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} -0 ${NSA_IP6} log_test_addr ${a} $? 0 "Client, device bind" log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} -C -0 ${NSA_IP6} log_test_addr ${a} $? 0 "Client, device send via cmsg" log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} -S -0 ${NSA_IP6} log_test_addr ${a} $? 0 "Client, device bind via IPV6_UNICAST_IF" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -D -r ${a} log_test_addr ${a} $? 1 "No server, unbound client" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "No server, device client" done # # local address tests # for a in ${NSA_IP6} ${NSA_LO_IP6} ::1 do log_start run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -0 ${a} -1 ${a} log_test_addr ${a} $? 0 "Global server, local connection" done a=${NSA_IP6} log_start run_cmd nettest -6 -s -D -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Device server, unbound client, local connection" for a in ${NSA_LO_IP6} ::1 do log_start show_hint "Should fail 'Connection refused' since address is out of device scope" run_cmd nettest -6 -s -D -I ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -r ${a} log_test_addr ${a} $? 1 "Device server, local connection" done a=${NSA_IP6} log_start run_cmd nettest -6 -s -D & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Global server, device client, local connection" log_start run_cmd nettest -6 -s -D & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -C -r ${a} log_test_addr ${a} $? 0 "Global server, device send via cmsg, local connection" log_start run_cmd nettest -6 -s -D & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -S -r ${a} log_test_addr ${a} $? 0 "Global server, device client via IPV6_UNICAST_IF, local connection" for a in ${NSA_LO_IP6} ::1 do log_start show_hint "Should fail 'No route to host' since addresses on loopback are out of device scope" run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} log_test_addr ${a} $? 1 "Global server, device client, local connection" log_start show_hint "Should fail 'No route to host' since addresses on loopback are out of device scope" run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} -C log_test_addr ${a} $? 1 "Global server, device send via cmsg, local connection" log_start show_hint "Should fail 'No route to host' since addresses on loopback are out of device scope" run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -r ${a} -d ${NSA_DEV} -S log_test_addr ${a} $? 1 "Global server, device client via IP_UNICAST_IF, local connection" done a=${NSA_IP6} log_start run_cmd nettest -6 -D -s -I ${NSA_DEV} -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} -0 ${a} log_test_addr ${a} $? 0 "Device server, device client, local conn" log_start show_hint "Should fail 'Connection refused'" run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 1 "No server, device client, local conn" # LLA to GUA run_cmd_nsb ip -6 addr del ${NSB_IP6}/64 dev ${NSB_DEV} run_cmd_nsb ip -6 ro add ${NSA_IP6}/128 dev ${NSB_DEV} log_start run_cmd nettest -6 -s -D & sleep 1 run_cmd_nsb nettest -6 -D -r ${NSA_IP6} log_test $? 0 "UDP in - LLA to GUA" run_cmd_nsb ip -6 ro del ${NSA_IP6}/128 dev ${NSB_DEV} run_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV} nodad } ipv6_udp_vrf() { local a # disable global server log_subsection "Global server disabled" set_sysctl net.ipv4.udp_l3mdev_accept=0 # # server tests # for a in ${NSA_IP6} ${VRF_IP6} do log_start show_hint "Should fail 'Connection refused' since global server is disabled" run_cmd nettest -6 -D -s & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 1 "Global server" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "VRF server" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Enslaved device server" done # negative test - should fail for a in ${NSA_IP6} ${VRF_IP6} do log_start show_hint "Should fail 'Connection refused' since there is no server" run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 1 "No server" done # # local address tests # for a in ${NSA_IP6} ${VRF_IP6} do log_start show_hint "Should fail 'Connection refused' since global server is disabled" run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 1 "Global server, VRF client, local conn" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -I ${VRF} -s & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local conn" done a=${NSA_IP6} log_start show_hint "Should fail 'Connection refused' since global server is disabled" run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 1 "Global server, device client, local conn" log_start run_cmd nettest -6 -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "VRF server, device client, local conn" log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Enslaved device server, VRF client, local conn" log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Enslaved device server, device client, local conn" # disable global server log_subsection "Global server enabled" set_sysctl net.ipv4.udp_l3mdev_accept=1 # # server tests # for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Global server" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "VRF server" done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 0 "Enslaved device server" done # negative test - should fail for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd_nsb nettest -6 -D -r ${a} log_test_addr ${a} $? 1 "No server" done # # client tests # log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${NSB_IP6} log_test $? 0 "VRF client" # negative test - should fail log_start run_cmd nettest -6 -D -d ${VRF} -r ${NSB_IP6} log_test $? 1 "No server, VRF client" log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${NSB_IP6} log_test $? 0 "Enslaved device client" # negative test - should fail log_start run_cmd nettest -6 -D -d ${NSA_DEV} -r ${NSB_IP6} log_test $? 1 "No server, enslaved device client" # # local address tests # a=${NSA_IP6} log_start run_cmd nettest -6 -D -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Global server, VRF client, local conn" #log_start run_cmd nettest -6 -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local conn" a=${VRF_IP6} log_start run_cmd nettest -6 -D -s -3 ${VRF} & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Global server, VRF client, local conn" log_start run_cmd nettest -6 -D -I ${VRF} -s -3 ${VRF} & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "VRF server, VRF client, local conn" # negative test - should fail for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 1 "No server, VRF client, local conn" done # device to global IP a=${NSA_IP6} log_start run_cmd nettest -6 -D -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Global server, device client, local conn" log_start run_cmd nettest -6 -D -I ${VRF} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "VRF server, device client, local conn" log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${VRF} -r ${a} log_test_addr ${a} $? 0 "Device server, VRF client, local conn" log_start run_cmd nettest -6 -D -I ${NSA_DEV} -s -3 ${NSA_DEV} & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 0 "Device server, device client, local conn" log_start run_cmd nettest -6 -D -d ${NSA_DEV} -r ${a} log_test_addr ${a} $? 1 "No server, device client, local conn" # link local addresses log_start run_cmd nettest -6 -D -s & sleep 1 run_cmd_nsb nettest -6 -D -d ${NSB_DEV} -r ${NSA_LINKIP6} log_test $? 0 "Global server, linklocal IP" log_start run_cmd_nsb nettest -6 -D -d ${NSB_DEV} -r ${NSA_LINKIP6} log_test $? 1 "No server, linklocal IP" log_start run_cmd_nsb nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${NSB_LINKIP6} log_test $? 0 "Enslaved device client, linklocal IP" log_start run_cmd nettest -6 -D -d ${NSA_DEV} -r ${NSB_LINKIP6} log_test $? 1 "No server, device client, peer linklocal IP" log_start run_cmd nettest -6 -D -s & sleep 1 run_cmd nettest -6 -D -d ${NSA_DEV} -r ${NSA_LINKIP6} log_test $? 0 "Enslaved device client, local conn - linklocal IP" log_start run_cmd nettest -6 -D -d ${NSA_DEV} -r ${NSA_LINKIP6} log_test $? 1 "No server, device client, local conn - linklocal IP" # LLA to GUA run_cmd_nsb ip -6 addr del ${NSB_IP6}/64 dev ${NSB_DEV} run_cmd_nsb ip -6 ro add ${NSA_IP6}/128 dev ${NSB_DEV} log_start run_cmd nettest -6 -s -D & sleep 1 run_cmd_nsb nettest -6 -D -r ${NSA_IP6} log_test $? 0 "UDP in - LLA to GUA" run_cmd_nsb ip -6 ro del ${NSA_IP6}/128 dev ${NSB_DEV} run_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV} nodad } ipv6_udp() { # should not matter, but set to known state set_sysctl net.ipv4.udp_early_demux=1 log_section "IPv6/UDP" log_subsection "No VRF" setup # udp_l3mdev_accept should have no affect without VRF; # run tests with it enabled and disabled to verify log_subsection "udp_l3mdev_accept disabled" set_sysctl net.ipv4.udp_l3mdev_accept=0 ipv6_udp_novrf log_subsection "udp_l3mdev_accept enabled" set_sysctl net.ipv4.udp_l3mdev_accept=1 ipv6_udp_novrf log_subsection "With VRF" setup "yes" ipv6_udp_vrf } ################################################################################ # IPv6 address bind ipv6_addr_bind_novrf() { # # raw socket # for a in ${NSA_IP6} ${NSA_LO_IP6} do log_start run_cmd nettest -6 -s -R -P ipv6-icmp -l ${a} -b log_test_addr ${a} $? 0 "Raw socket bind to local address" log_start run_cmd nettest -6 -s -R -P ipv6-icmp -l ${a} -I ${NSA_DEV} -b log_test_addr ${a} $? 0 "Raw socket bind to local address after device bind" done # # raw socket with nonlocal bind # a=${NL_IP6} log_start run_cmd nettest -6 -s -R -P icmp -f -l ${a} -I ${NSA_DEV} -b log_test_addr ${a} $? 0 "Raw socket bind to nonlocal address" # # tcp sockets # a=${NSA_IP6} log_start run_cmd nettest -6 -s -l ${a} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address" log_start run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address after device bind" # Sadly, the kernel allows binding a socket to a device and then # binding to an address not on the device. So this test passes # when it really should not a=${NSA_LO_IP6} log_start show_hint "Tecnically should fail since address is not on device but kernel allows" run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to out of scope local address" } ipv6_addr_bind_vrf() { # # raw socket # for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s -R -P ipv6-icmp -l ${a} -I ${VRF} -b log_test_addr ${a} $? 0 "Raw socket bind to local address after vrf bind" log_start run_cmd nettest -6 -s -R -P ipv6-icmp -l ${a} -I ${NSA_DEV} -b log_test_addr ${a} $? 0 "Raw socket bind to local address after device bind" done a=${NSA_LO_IP6} log_start show_hint "Address on loopback is out of VRF scope" run_cmd nettest -6 -s -R -P ipv6-icmp -l ${a} -I ${VRF} -b log_test_addr ${a} $? 1 "Raw socket bind to invalid local address after vrf bind" # # raw socket with nonlocal bind # a=${NL_IP6} log_start run_cmd nettest -6 -s -R -P icmp -f -l ${a} -I ${VRF} -b log_test_addr ${a} $? 0 "Raw socket bind to nonlocal address after VRF bind" # # tcp sockets # # address on enslaved device is valid for the VRF or device in a VRF for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s -l ${a} -I ${VRF} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address with VRF bind" done a=${NSA_IP6} log_start run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to local address with device bind" # Sadly, the kernel allows binding a socket to a device and then # binding to an address not on the device. The only restriction # is that the address is valid in the L3 domain. So this test # passes when it really should not a=${VRF_IP6} log_start show_hint "Tecnically should fail since address is not on device but kernel allows" run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 0 "TCP socket bind to VRF address with device bind" a=${NSA_LO_IP6} log_start show_hint "Address on loopback out of scope for VRF" run_cmd nettest -6 -s -l ${a} -I ${VRF} -t1 -b log_test_addr ${a} $? 1 "TCP socket bind to invalid local address for VRF" log_start show_hint "Address on loopback out of scope for device in VRF" run_cmd nettest -6 -s -l ${a} -I ${NSA_DEV} -t1 -b log_test_addr ${a} $? 1 "TCP socket bind to invalid local address for device bind" } ipv6_addr_bind() { log_section "IPv6 address binds" log_subsection "No VRF" setup ipv6_addr_bind_novrf log_subsection "With VRF" setup "yes" ipv6_addr_bind_vrf } ################################################################################ # IPv6 runtime tests ipv6_rt() { local desc="$1" local varg="-6 $2" local with_vrf="yes" local a # # server tests # for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest ${varg} -s & sleep 1 run_cmd_nsb nettest ${varg} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, global server" setup ${with_vrf} done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest ${varg} -I ${VRF} -s & sleep 1 run_cmd_nsb nettest ${varg} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF server" setup ${with_vrf} done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest ${varg} -I ${NSA_DEV} -s & sleep 1 run_cmd_nsb nettest ${varg} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, enslaved device server" setup ${with_vrf} done # # client test # log_start run_cmd_nsb nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${VRF} -r ${NSB_IP6} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test 0 0 "${desc}, VRF client" setup ${with_vrf} log_start run_cmd_nsb nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${NSB_IP6} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test 0 0 "${desc}, enslaved device client" setup ${with_vrf} # # local address tests # for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${VRF} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, global server, VRF client" setup ${with_vrf} done for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest ${varg} -I ${VRF} -s & sleep 1 run_cmd nettest ${varg} -d ${VRF} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF server and client" setup ${with_vrf} done a=${NSA_IP6} log_start run_cmd nettest ${varg} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, global server, device client" setup ${with_vrf} log_start run_cmd nettest ${varg} -I ${VRF} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, VRF server, device client" setup ${with_vrf} log_start run_cmd nettest ${varg} -I ${NSA_DEV} -s & sleep 1 run_cmd nettest ${varg} -d ${NSA_DEV} -r ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "${desc}, device server, device client" } ipv6_ping_rt() { local with_vrf="yes" local a a=${NSA_IP6} log_start run_cmd_nsb ${ping6} -f ${a} & sleep 3 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "Device delete with active traffic - ping in" setup ${with_vrf} log_start run_cmd ${ping6} -f ${NSB_IP6} -I ${VRF} & sleep 1 run_cmd ip link del ${VRF} sleep 1 log_test_addr ${a} 0 0 "Device delete with active traffic - ping out" } ipv6_runtime() { log_section "Run time tests - ipv6" setup "yes" ipv6_ping_rt setup "yes" ipv6_rt "TCP active socket" "-n -1" setup "yes" ipv6_rt "TCP passive socket" "-i" setup "yes" ipv6_rt "UDP active socket" "-D -n -1" } ################################################################################ # netfilter blocking connections netfilter_tcp_reset() { local a for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest -s & sleep 1 run_cmd_nsb nettest -r ${a} log_test_addr ${a} $? 1 "Global server, reject with TCP-reset on Rx" done } netfilter_icmp() { local stype="$1" local arg local a [ "${stype}" = "UDP" ] && arg="-D" for a in ${NSA_IP} ${VRF_IP} do log_start run_cmd nettest ${arg} -s & sleep 1 run_cmd_nsb nettest ${arg} -r ${a} log_test_addr ${a} $? 1 "Global ${stype} server, Rx reject icmp-port-unreach" done } ipv4_netfilter() { log_section "IPv4 Netfilter" log_subsection "TCP reset" setup "yes" run_cmd iptables -A INPUT -p tcp --dport 12345 -j REJECT --reject-with tcp-reset netfilter_tcp_reset log_start log_subsection "ICMP unreachable" log_start run_cmd iptables -F run_cmd iptables -A INPUT -p tcp --dport 12345 -j REJECT --reject-with icmp-port-unreachable run_cmd iptables -A INPUT -p udp --dport 12345 -j REJECT --reject-with icmp-port-unreachable netfilter_icmp "TCP" netfilter_icmp "UDP" log_start iptables -F } netfilter_tcp6_reset() { local a for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s & sleep 1 run_cmd_nsb nettest -6 -r ${a} log_test_addr ${a} $? 1 "Global server, reject with TCP-reset on Rx" done } netfilter_icmp6() { local stype="$1" local arg local a [ "${stype}" = "UDP" ] && arg="$arg -D" for a in ${NSA_IP6} ${VRF_IP6} do log_start run_cmd nettest -6 -s ${arg} & sleep 1 run_cmd_nsb nettest -6 ${arg} -r ${a} log_test_addr ${a} $? 1 "Global ${stype} server, Rx reject icmp-port-unreach" done } ipv6_netfilter() { log_section "IPv6 Netfilter" log_subsection "TCP reset" setup "yes" run_cmd ip6tables -A INPUT -p tcp --dport 12345 -j REJECT --reject-with tcp-reset netfilter_tcp6_reset log_subsection "ICMP unreachable" log_start run_cmd ip6tables -F run_cmd ip6tables -A INPUT -p tcp --dport 12345 -j REJECT --reject-with icmp6-port-unreachable run_cmd ip6tables -A INPUT -p udp --dport 12345 -j REJECT --reject-with icmp6-port-unreachable netfilter_icmp6 "TCP" netfilter_icmp6 "UDP" log_start ip6tables -F } ################################################################################ # specific use cases # VRF only. # ns-A device enslaved to bridge. Verify traffic with and without # br_netfilter module loaded. Repeat with SVI on bridge. use_case_br() { setup "yes" setup_cmd ip link set ${NSA_DEV} down setup_cmd ip addr del dev ${NSA_DEV} ${NSA_IP}/24 setup_cmd ip -6 addr del dev ${NSA_DEV} ${NSA_IP6}/64 setup_cmd ip link add br0 type bridge setup_cmd ip addr add dev br0 ${NSA_IP}/24 setup_cmd ip -6 addr add dev br0 ${NSA_IP6}/64 nodad setup_cmd ip li set ${NSA_DEV} master br0 setup_cmd ip li set ${NSA_DEV} up setup_cmd ip li set br0 up setup_cmd ip li set br0 vrf ${VRF} rmmod br_netfilter 2>/dev/null sleep 5 # DAD run_cmd ip neigh flush all run_cmd ping -c1 -w1 -I br0 ${NSB_IP} log_test $? 0 "Bridge into VRF - IPv4 ping out" run_cmd ip neigh flush all run_cmd ${ping6} -c1 -w1 -I br0 ${NSB_IP6} log_test $? 0 "Bridge into VRF - IPv6 ping out" run_cmd ip neigh flush all run_cmd_nsb ping -c1 -w1 ${NSA_IP} log_test $? 0 "Bridge into VRF - IPv4 ping in" run_cmd ip neigh flush all run_cmd_nsb ${ping6} -c1 -w1 ${NSA_IP6} log_test $? 0 "Bridge into VRF - IPv6 ping in" modprobe br_netfilter if [ $? -eq 0 ]; then run_cmd ip neigh flush all run_cmd ping -c1 -w1 -I br0 ${NSB_IP} log_test $? 0 "Bridge into VRF with br_netfilter - IPv4 ping out" run_cmd ip neigh flush all run_cmd ${ping6} -c1 -w1 -I br0 ${NSB_IP6} log_test $? 0 "Bridge into VRF with br_netfilter - IPv6 ping out" run_cmd ip neigh flush all run_cmd_nsb ping -c1 -w1 ${NSA_IP} log_test $? 0 "Bridge into VRF with br_netfilter - IPv4 ping in" run_cmd ip neigh flush all run_cmd_nsb ${ping6} -c1 -w1 ${NSA_IP6} log_test $? 0 "Bridge into VRF with br_netfilter - IPv6 ping in" fi setup_cmd ip li set br0 nomaster setup_cmd ip li add br0.100 link br0 type vlan id 100 setup_cmd ip li set br0.100 vrf ${VRF} up setup_cmd ip addr add dev br0.100 172.16.101.1/24 setup_cmd ip -6 addr add dev br0.100 2001:db8:101::1/64 nodad setup_cmd_nsb ip li add vlan100 link ${NSB_DEV} type vlan id 100 setup_cmd_nsb ip addr add dev vlan100 172.16.101.2/24 setup_cmd_nsb ip -6 addr add dev vlan100 2001:db8:101::2/64 nodad setup_cmd_nsb ip li set vlan100 up sleep 1 rmmod br_netfilter 2>/dev/null run_cmd ip neigh flush all run_cmd ping -c1 -w1 -I br0.100 172.16.101.2 log_test $? 0 "Bridge vlan into VRF - IPv4 ping out" run_cmd ip neigh flush all run_cmd ${ping6} -c1 -w1 -I br0.100 2001:db8:101::2 log_test $? 0 "Bridge vlan into VRF - IPv6 ping out" run_cmd ip neigh flush all run_cmd_nsb ping -c1 -w1 172.16.101.1 log_test $? 0 "Bridge vlan into VRF - IPv4 ping in" run_cmd ip neigh flush all run_cmd_nsb ${ping6} -c1 -w1 2001:db8:101::1 log_test $? 0 "Bridge vlan into VRF - IPv6 ping in" modprobe br_netfilter if [ $? -eq 0 ]; then run_cmd ip neigh flush all run_cmd ping -c1 -w1 -I br0.100 172.16.101.2 log_test $? 0 "Bridge vlan into VRF with br_netfilter - IPv4 ping out" run_cmd ip neigh flush all run_cmd ${ping6} -c1 -w1 -I br0.100 2001:db8:101::2 log_test $? 0 "Bridge vlan into VRF with br_netfilter - IPv6 ping out" run_cmd ip neigh flush all run_cmd_nsb ping -c1 -w1 172.16.101.1 log_test $? 0 "Bridge vlan into VRF - IPv4 ping in" run_cmd ip neigh flush all run_cmd_nsb ${ping6} -c1 -w1 2001:db8:101::1 log_test $? 0 "Bridge vlan into VRF - IPv6 ping in" fi setup_cmd ip li del br0 2>/dev/null setup_cmd_nsb ip li del vlan100 2>/dev/null } # VRF only. # ns-A device is connected to both ns-B and ns-C on a single VRF but only has # LLA on the interfaces use_case_ping_lla_multi() { setup_lla_only # only want reply from ns-A setup_cmd_nsb sysctl -qw net.ipv6.icmp.echo_ignore_multicast=1 setup_cmd_nsc sysctl -qw net.ipv6.icmp.echo_ignore_multicast=1 log_start run_cmd_nsb ping -c1 -w1 ${MCAST}%${NSB_DEV} log_test_addr ${MCAST}%${NSB_DEV} $? 0 "Pre cycle, ping out ns-B" run_cmd_nsc ping -c1 -w1 ${MCAST}%${NSC_DEV} log_test_addr ${MCAST}%${NSC_DEV} $? 0 "Pre cycle, ping out ns-C" # cycle/flap the first ns-A interface setup_cmd ip link set ${NSA_DEV} down setup_cmd ip link set ${NSA_DEV} up sleep 1 log_start run_cmd_nsb ping -c1 -w1 ${MCAST}%${NSB_DEV} log_test_addr ${MCAST}%${NSB_DEV} $? 0 "Post cycle ${NSA} ${NSA_DEV}, ping out ns-B" run_cmd_nsc ping -c1 -w1 ${MCAST}%${NSC_DEV} log_test_addr ${MCAST}%${NSC_DEV} $? 0 "Post cycle ${NSA} ${NSA_DEV}, ping out ns-C" # cycle/flap the second ns-A interface setup_cmd ip link set ${NSA_DEV2} down setup_cmd ip link set ${NSA_DEV2} up sleep 1 log_start run_cmd_nsb ping -c1 -w1 ${MCAST}%${NSB_DEV} log_test_addr ${MCAST}%${NSB_DEV} $? 0 "Post cycle ${NSA} ${NSA_DEV2}, ping out ns-B" run_cmd_nsc ping -c1 -w1 ${MCAST}%${NSC_DEV} log_test_addr ${MCAST}%${NSC_DEV} $? 0 "Post cycle ${NSA} ${NSA_DEV2}, ping out ns-C" } # Perform IPv{4,6} SNAT on ns-A, and verify TCP connection is successfully # established with ns-B. use_case_snat_on_vrf() { setup "yes" local port="12345" run_cmd iptables -t nat -A POSTROUTING -p tcp -m tcp --dport ${port} -j SNAT --to-source ${NSA_LO_IP} -o ${VRF} run_cmd ip6tables -t nat -A POSTROUTING -p tcp -m tcp --dport ${port} -j SNAT --to-source ${NSA_LO_IP6} -o ${VRF} run_cmd_nsb nettest -s -l ${NSB_IP} -p ${port} & sleep 1 run_cmd nettest -d ${VRF} -r ${NSB_IP} -p ${port} log_test $? 0 "IPv4 TCP connection over VRF with SNAT" run_cmd_nsb nettest -6 -s -l ${NSB_IP6} -p ${port} & sleep 1 run_cmd nettest -6 -d ${VRF} -r ${NSB_IP6} -p ${port} log_test $? 0 "IPv6 TCP connection over VRF with SNAT" # Cleanup run_cmd iptables -t nat -D POSTROUTING -p tcp -m tcp --dport ${port} -j SNAT --to-source ${NSA_LO_IP} -o ${VRF} run_cmd ip6tables -t nat -D POSTROUTING -p tcp -m tcp --dport ${port} -j SNAT --to-source ${NSA_LO_IP6} -o ${VRF} } use_cases() { log_section "Use cases" log_subsection "Device enslaved to bridge" use_case_br log_subsection "Ping LLA with multiple interfaces" use_case_ping_lla_multi log_subsection "SNAT on VRF" use_case_snat_on_vrf } ################################################################################ # usage usage() { cat < Test name/set to run -p Pause on fail -P Pause after each test -v Be verbose Tests: $TESTS_IPV4 $TESTS_IPV6 $TESTS_OTHER EOF } ################################################################################ # main TESTS_IPV4="ipv4_ping ipv4_tcp ipv4_udp ipv4_bind ipv4_runtime ipv4_netfilter" TESTS_IPV6="ipv6_ping ipv6_tcp ipv6_udp ipv6_bind ipv6_runtime ipv6_netfilter" TESTS_OTHER="use_cases" PAUSE_ON_FAIL=no PAUSE=no while getopts :46t:pPvh o do case $o in 4) TESTS=ipv4;; 6) TESTS=ipv6;; t) TESTS=$OPTARG;; p) PAUSE_ON_FAIL=yes;; P) PAUSE=yes;; v) VERBOSE=1;; h) usage; exit 0;; *) usage; exit 1;; esac done # make sure we don't pause twice [ "${PAUSE}" = "yes" ] && PAUSE_ON_FAIL=no # # show user test config # if [ -z "$TESTS" ]; then TESTS="$TESTS_IPV4 $TESTS_IPV6 $TESTS_OTHER" elif [ "$TESTS" = "ipv4" ]; then TESTS="$TESTS_IPV4" elif [ "$TESTS" = "ipv6" ]; then TESTS="$TESTS_IPV6" fi which nettest >/dev/null if [ $? -ne 0 ]; then echo "'nettest' command not found; skipping tests" exit $ksft_skip fi declare -i nfail=0 declare -i nsuccess=0 for t in $TESTS do case $t in ipv4_ping|ping) ipv4_ping;; ipv4_tcp|tcp) ipv4_tcp;; ipv4_udp|udp) ipv4_udp;; ipv4_bind|bind) ipv4_addr_bind;; ipv4_runtime) ipv4_runtime;; ipv4_netfilter) ipv4_netfilter;; ipv6_ping|ping6) ipv6_ping;; ipv6_tcp|tcp6) ipv6_tcp;; ipv6_udp|udp6) ipv6_udp;; ipv6_bind|bind6) ipv6_addr_bind;; ipv6_runtime) ipv6_runtime;; ipv6_netfilter) ipv6_netfilter;; use_cases) use_cases;; # setup namespaces and config, but do not run any tests setup) setup; exit 0;; vrf_setup) setup "yes"; exit 0;; esac done cleanup 2>/dev/null printf "\nTests passed: %3d\n" ${nsuccess} printf "Tests failed: %3d\n" ${nfail} if [ $nfail -ne 0 ]; then exit 1 # KSFT_FAIL elif [ $nsuccess -eq 0 ]; then exit $ksft_skip fi exit 0 # KSFT_PASS