diff options
author | Linus Torvalds <torvalds@linux-foundation.org> | 2023-08-31 02:53:46 +0300 |
---|---|---|
committer | Linus Torvalds <torvalds@linux-foundation.org> | 2023-08-31 02:53:46 +0300 |
commit | 0e72db77672ff4758a31fb5259c754a7bb229751 (patch) | |
tree | 71afc69a3b476180115e6b9479e582b340828711 /Documentation/devicetree/bindings/serial | |
parent | a1c19328a160c80251868dbd80066dce23d07995 (diff) | |
parent | 05c618f39089d977b0c3dc1105cb6cd5fc53cd01 (diff) | |
download | linux-0e72db77672ff4758a31fb5259c754a7bb229751.tar.xz |
Merge tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"These are the devicetree updates for Arm and RISC-V based SoCs, mainly
from Qualcomm, NXP/Freescale, Aspeed, TI, Rockchips, Samsung, ST and
Starfive.
Only a few new SoC got added:
- TI AM62P5, a variant of the existing Sitara AM62x family
- Intel Agilex5, an FPGFA platform that includes an Cortex-A76/A55
SoC.
- Qualcomm ipq5018 is used in wireless access points
- Qualcomm SM4450 (Snapdragon 4 Gen 2) is a new low-end mobile phone
platform.
In total, 29 machines get added, which is low because of the summer
break. These cover SoCs from Aspeed, Broadcom, NXP, Samsung, ST,
Allwinner, Amlogic, Intel, Qualcomm, Rockchip, TI and T-Head. Most of
these are development and reference boards.
Despite not adding a lot of new machines, there are over 700 patches
in total, most of which are cleanups and minor fixes"
* tag 'soc-dt-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (735 commits)
arm64: dts: use capital "OR" for multiple licenses in SPDX
ARM: dts: use capital "OR" for multiple licenses in SPDX
arm64: dts: qcom: sdm845-db845c: Mark cont splash memory region as reserved
ARM: dts: qcom: apq8064: add support to gsbi4 uart
riscv: dts: change TH1520 files to dual license
riscv: dts: thead: add BeagleV Ahead board device tree
dt-bindings: riscv: Add BeagleV Ahead board compatibles
ARM: dts: stm32: add SCMI PMIC regulators on stm32mp135f-dk board
ARM: dts: stm32: STM32MP13x SoC exposes SCMI regulators
dt-bindings: rcc: stm32: add STM32MP13 SCMI regulators IDs
ARM: dts: stm32: support display on stm32f746-disco board
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f746-disco
ARM: dts: stm32: add pin map for LTDC on stm32f7
ARM: dts: stm32: add ltdc support on stm32f746 MCU
arm64: dts: qcom: sm6350: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sa8775p: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sc8280xp: Hook up PDC as wakeup-parent of TLMM
arm64: dts: qcom: sdm670: Add PDC
riscv: dts: starfive: fix jh7110 qspi sort order
...
Diffstat (limited to 'Documentation/devicetree/bindings/serial')
-rw-r--r-- | Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt | 73 | ||||
-rw-r--r-- | Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml | 125 |
2 files changed, 125 insertions, 73 deletions
diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt deleted file mode 100644 index f709304036c2..000000000000 --- a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.txt +++ /dev/null @@ -1,73 +0,0 @@ -NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver. - -Required properties: -- compatible : should be, - "nvidia,tegra20-hsuart" for Tegra20, - "nvidia,tegra30-hsuart" for Tegra30, - "nvidia,tegra186-hsuart" for Tegra186, - "nvidia,tegra194-hsuart" for Tegra194. - -- reg: Should contain UART controller registers location and length. -- interrupts: Should contain UART controller interrupts. -- clocks: Must contain one entry, for the module clock. - See ../clocks/clock-bindings.txt for details. -- resets : Must contain an entry for each entry in reset-names. - See ../reset/reset.txt for details. -- reset-names : Must include the following entries: - - serial -- dmas : Must contain an entry for each entry in dma-names. - See ../dma/dma.txt for details. -- dma-names : Must include the following entries: - - rx - - tx - -Optional properties: -- nvidia,enable-modem-interrupt: Enable modem interrupts. Should be enable - only if all 8 lines of UART controller are pinmuxed. -- nvidia,adjust-baud-rates: List of entries providing percentage of baud rate - adjustment within a range. - Each entry contains sets of 3 values. Range low/high and adjusted rate. - <range_low range_high adjusted_rate> - When baud rate set on controller falls within the range mentioned in this - field, baud rate will be adjusted by percentage mentioned here. - Ex: <9600 115200 200> - Increase baud rate by 2% when set baud rate falls within range 9600 to 115200 - -Baud Rate tolerance: - Standard UART devices are expected to have tolerance for baud rate error by - -4 to +4 %. All Tegra devices till Tegra210 had this support. However, - Tegra186 chip has a known hardware issue. UART Rx baud rate tolerance level - is 0% to +4% in 1-stop config. Otherwise, the received data will have - corruption/invalid framing errors. Parker errata suggests adjusting baud - rate to be higher than the deviations observed in Tx. - - Tx deviation of connected device can be captured over scope (or noted from - its spec) for valid range and Tegra baud rate has to be set above actual - Tx baud rate observed. To do this we use nvidia,adjust-baud-rates - - As an example, consider there is deviation observed in Tx for baud rates as - listed below. - 0 to 9600 has 1% deviation - 9600 to 115200 2% deviation - This slight deviation is expcted and Tegra UART is expected to handle it. Due - to the issue stated above, baud rate on Tegra UART should be set equal to or - above deviation observed for avoiding frame errors. - Property should be set like this - nvidia,adjust-baud-rates = <0 9600 100>, - <9600 115200 200>; - -Example: - -serial@70006000 { - compatible = "nvidia,tegra30-hsuart", "nvidia,tegra20-hsuart"; - reg = <0x70006000 0x40>; - reg-shift = <2>; - interrupts = <0 36 0x04>; - nvidia,enable-modem-interrupt; - clocks = <&tegra_car 6>; - resets = <&tegra_car 6>; - reset-names = "serial"; - dmas = <&apbdma 8>, <&apbdma 8>; - dma-names = "rx", "tx"; - nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */ -}; diff --git a/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml new file mode 100644 index 000000000000..04d55fecf47c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nvidia,tegra20-hsuart.yaml @@ -0,0 +1,125 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/serial/nvidia,tegra20-hsuart.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra20/Tegra30 high speed (DMA based) UART controller driver + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +properties: + compatible: + oneOf: + - enum: + - nvidia,tegra20-hsuart + - nvidia,tegra30-hsuart + - nvidia,tegra186-hsuart + - nvidia,tegra194-hsuart + - items: + - const: nvidia,tegra124-hsuart + - const: nvidia,tegra30-hsuart + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: module clock + + resets: + items: + - description: module reset + + reset-names: + items: + - const: serial + + dmas: + items: + - description: DMA channel used for reception + - description: DMA channel used for transmission + + dma-names: + items: + - const: rx + - const: tx + + nvidia,enable-modem-interrupt: + $ref: /schemas/types.yaml#/definitions/flag + description: Enable modem interrupts. Should be enable only if all 8 lines of UART controller + are pinmuxed. + + nvidia,adjust-baud-rates: + $ref: /schemas/types.yaml#/definitions/uint32-matrix + description: | + List of entries providing percentage of baud rate adjustment within a range. Each entry + contains a set of 3 values: range low/high and adjusted rate. When the baud rate set on the + controller falls within the range mentioned in this field, the baud rate will be adjusted by + percentage mentioned here. + + Example: <9600 115200 200> + + Increase baud rate by 2% when set baud rate falls within range 9600 to 115200. + + Standard UART devices are expected to have tolerance for baud rate error by -4 to +4 %. All + Tegra devices till Tegra210 had this support. However, Tegra186 chip has a known hardware + issue. UART RX baud rate tolerance level is 0% to +4% in 1-stop config. Otherwise, the + received data will have corruption/invalid framing errors. Parker errata suggests adjusting + baud rate to be higher than the deviations observed in TX. + + TX deviation of connected device can be captured over scope (or noted from its spec) for + valid range and Tegra baud rate has to be set above actual TX baud rate observed. To do this + we use nvidia,adjust-baud-rates. + + As an example, consider there is deviation observed in TX for baud rates as listed below. 0 + to 9600 has 1% deviation 9600 to 115200 2% deviation. This slight deviation is expcted and + Tegra UART is expected to handle it. Due to the issue stated above, baud rate on Tegra UART + should be set equal to or above deviation observed for avoiding frame errors. Property + should be set like this: + + nvidia,adjust-baud-rates = <0 9600 100>, + <9600 115200 200>; + items: + items: + - description: range lower bound + - description: range upper bound + - description: adjustment (in permyriad, i.e. 0.01%) + +allOf: + - $ref: serial.yaml + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + - clocks + - resets + - reset-names + - dmas + - dma-names + +examples: + - | + #include <dt-bindings/clock/tegra30-car.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + serial@70006000 { + compatible = "nvidia,tegra30-hsuart"; + reg = <0x70006000 0x40>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + nvidia,enable-modem-interrupt; + clocks = <&tegra_car TEGRA30_CLK_UARTA>; + resets = <&tegra_car 6>; + reset-names = "serial"; + dmas = <&apbdma 8>, <&apbdma 8>; + dma-names = "rx", "tx"; + nvidia,adjust-baud-rates = <1000000 4000000 136>; /* 1.36% shift */ + }; |