summaryrefslogtreecommitdiff
path: root/Documentation/hwmon/ltc4260.rst
diff options
context:
space:
mode:
authorMauro Carvalho Chehab <mchehab+samsung@kernel.org>2019-04-17 12:46:29 +0300
committerGuenter Roeck <linux@roeck-us.net>2019-04-17 20:37:23 +0300
commit7ebd8b66dd9e5a0b65e5ee5e2b8e7ca382ec97b7 (patch)
tree9db30159bd32bec125c7d49e80a79bb7c4da0c8e /Documentation/hwmon/ltc4260.rst
parentb04f2f7d387b3160883c2a1f5e2285483a791e82 (diff)
downloadlinux-7ebd8b66dd9e5a0b65e5ee5e2b8e7ca382ec97b7.tar.xz
docs: hwmon: Add an index file and rename docs to *.rst
Now that all files were converted to ReST format, rename them and add an index. Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Diffstat (limited to 'Documentation/hwmon/ltc4260.rst')
-rw-r--r--Documentation/hwmon/ltc4260.rst64
1 files changed, 64 insertions, 0 deletions
diff --git a/Documentation/hwmon/ltc4260.rst b/Documentation/hwmon/ltc4260.rst
new file mode 100644
index 000000000000..4c335b6a51d1
--- /dev/null
+++ b/Documentation/hwmon/ltc4260.rst
@@ -0,0 +1,64 @@
+Kernel driver ltc4260
+=====================
+
+Supported chips:
+
+ * Linear Technology LTC4260
+
+ Prefix: 'ltc4260'
+
+ Addresses scanned: -
+
+ Datasheet:
+
+ http://cds.linear.com/docs/en/datasheet/4260fc.pdf
+
+Author: Guenter Roeck <linux@roeck-us.net>
+
+
+Description
+-----------
+
+The LTC4260 Hot Swap controller allows a board to be safely inserted
+and removed from a live backplane.
+
+
+Usage Notes
+-----------
+
+This driver does not probe for LTC4260 devices, since there is no register
+which can be safely used to identify the chip. You will have to instantiate
+the devices explicitly.
+
+Example: the following will load the driver for an LTC4260 at address 0x10
+on I2C bus #1::
+
+ $ modprobe ltc4260
+ $ echo ltc4260 0x10 > /sys/bus/i2c/devices/i2c-1/new_device
+
+
+Sysfs entries
+-------------
+
+Voltage readings provided by this driver are reported as obtained from the ADC
+registers. If a set of voltage divider resistors is installed, calculate the
+real voltage by multiplying the reported value with (R1+R2)/R2, where R1 is the
+value of the divider resistor against the measured voltage and R2 is the value
+of the divider resistor against Ground.
+
+Current reading provided by this driver is reported as obtained from the ADC
+Current Sense register. The reported value assumes that a 1 mOhm sense resistor
+is installed. If a different sense resistor is installed, calculate the real
+current by dividing the reported value by the sense resistor value in mOhm.
+
+======================= =======================
+in1_input SOURCE voltage (mV)
+in1_min_alarm Undervoltage alarm
+in1_max_alarm Overvoltage alarm
+
+in2_input ADIN voltage (mV)
+in2_alarm Power bad alarm
+
+curr1_input SENSE current (mA)
+curr1_alarm SENSE overcurrent alarm
+======================= =======================