diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2023-06-30 01:07:06 +0300 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2023-06-30 01:07:06 +0300 |
| commit | 6c1561fb900524c5bceb924071b3e9b8a67ff3da (patch) | |
| tree | 3bedd8d3bfac4b15a176e53449b2889418040e44 /arch/arm/boot/dts/intel | |
| parent | b775d6c5859affe00527cbe74263de05cfe6b9f9 (diff) | |
| parent | 46448b36ff8c807194d5884a6efce00891e4bd02 (diff) | |
| download | linux-6c1561fb900524c5bceb924071b3e9b8a67ff3da.tar.xz | |
Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
Diffstat (limited to 'arch/arm/boot/dts/intel')
64 files changed, 8975 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/intel/Makefile b/arch/arm/boot/dts/intel/Makefile new file mode 100644 index 000000000000..c5fc845deb61 --- /dev/null +++ b/arch/arm/boot/dts/intel/Makefile @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0 +subdir-y += axm +subdir-y += ixp +subdir-y += pxa +subdir-y += socfpga diff --git a/arch/arm/boot/dts/intel/axm/Makefile b/arch/arm/boot/dts/intel/axm/Makefile new file mode 100644 index 000000000000..7c7dc679964d --- /dev/null +++ b/arch/arm/boot/dts/intel/axm/Makefile @@ -0,0 +1,5 @@ +# SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_AXXIA) += \ + axm5516-amarillo.dtb +dtb-$(CONFIG_ARCH_AXXIA) += \ + axm5516-amarillo.dtb diff --git a/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts b/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts new file mode 100644 index 000000000000..2e2ad3c7ee77 --- /dev/null +++ b/arch/arm/boot/dts/intel/axm/axm5516-amarillo.dts @@ -0,0 +1,47 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * arch/arm/boot/dts/axm5516-amarillo.dts + * + * Copyright (C) 2013 LSI + */ + +/dts-v1/; + +/memreserve/ 0x00000000 0x00400000; + +#include "axm55xx.dtsi" +#include "axm5516-cpus.dtsi" + +/ { + model = "Amarillo AXM5516"; + compatible = "lsi,axm5516-amarillo", "lsi,axm5516"; + + memory { + device_type = "memory"; + reg = <0 0x00000000 0x02 0x00000000>; + }; +}; + +&serial0 { + status = "okay"; +}; + +&serial1 { + status = "okay"; +}; + +&serial2 { + status = "okay"; +}; + +&serial3 { + status = "okay"; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi b/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi new file mode 100644 index 000000000000..f13ef80b6637 --- /dev/null +++ b/arch/arm/boot/dts/intel/axm/axm5516-cpus.dtsi @@ -0,0 +1,200 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * arch/arm/boot/dts/axm5516-cpus.dtsi + * + * Copyright (C) 2013 LSI + */ + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + core1 { + cpu = <&CPU1>; + }; + core2 { + cpu = <&CPU2>; + }; + core3 { + cpu = <&CPU3>; + }; + }; + cluster1 { + core0 { + cpu = <&CPU4>; + }; + core1 { + cpu = <&CPU5>; + }; + core2 { + cpu = <&CPU6>; + }; + core3 { + cpu = <&CPU7>; + }; + }; + cluster2 { + core0 { + cpu = <&CPU8>; + }; + core1 { + cpu = <&CPU9>; + }; + core2 { + cpu = <&CPU10>; + }; + core3 { + cpu = <&CPU11>; + }; + }; + cluster3 { + core0 { + cpu = <&CPU12>; + }; + core1 { + cpu = <&CPU13>; + }; + core2 { + cpu = <&CPU14>; + }; + core3 { + cpu = <&CPU15>; + }; + }; + }; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x00>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x01>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU2: cpu@2 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x02>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU3: cpu@3 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x03>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU4: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x100>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU5: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x101>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU6: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x102>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU7: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x103>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU8: cpu@200 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x200>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU9: cpu@201 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x201>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU10: cpu@202 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x202>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU11: cpu@203 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x203>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU12: cpu@300 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x300>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU13: cpu@301 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x301>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU14: cpu@302 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x302>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + + CPU15: cpu@303 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x303>; + clock-frequency = <1400000000>; + cpu-release-addr = <0>; // Fixed by the boot loader + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/axm/axm55xx.dtsi b/arch/arm/boot/dts/intel/axm/axm55xx.dtsi new file mode 100644 index 000000000000..5277890cfad2 --- /dev/null +++ b/arch/arm/boot/dts/intel/axm/axm55xx.dtsi @@ -0,0 +1,200 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * arch/arm/boot/dts/axm55xx.dtsi + * + * Copyright (C) 2013 LSI + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/lsi,axm5516-clks.h> + +/ { + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&gic>; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + serial2 = &serial2; + serial3 = &serial3; + timer = &timer0; + }; + + clocks { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clk_ref0: clk_ref0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clk_ref1: clk_ref1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clk_ref2: clk_ref2 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clks: clock-controller@2010020000 { + compatible = "lsi,axm5516-clks"; + #clock-cells = <1>; + reg = <0x20 0x10020000 0 0x20000>; + }; + }; + + gic: interrupt-controller@2001001000 { + compatible = "arm,cortex-a15-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x20 0x01001000 0 0x1000>, + <0x20 0x01002000 0 0x2000>, + <0x20 0x01004000 0 0x2000>, + <0x20 0x01006000 0 0x2000>; + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | + IRQ_TYPE_LEVEL_HIGH)>; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = + <GIC_PPI 13 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + + pmu { + compatible = "arm,cortex-a15-pmu"; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; + }; + + soc { + compatible = "simple-bus"; + device_type = "soc"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&gic>; + ranges; + + syscon: syscon@2010030000 { + compatible = "lsi,axxia-syscon", "syscon"; + reg = <0x20 0x10030000 0 0x2000>; + }; + + reset: reset@2010031000 { + compatible = "lsi,axm55xx-reset"; + syscon = <&syscon>; + }; + + amba { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + serial0: serial@2010080000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x20 0x10080000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + serial1: serial@2010081000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x20 0x10081000 0 0x1000>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + serial2: serial@2010082000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x20 0x10082000 0 0x1000>; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + serial3: serial@2010083000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x20 0x10083000 0 0x1000>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + timer0: timer@2010091000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x20 0x10091000 0 0x1000>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "okay"; + }; + + gpio0: gpio@2010092000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x20 0x10092000 0x00 0x1000>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + + gpio1: gpio@2010093000 { + #gpio-cells = <2>; + compatible = "arm,pl061", "arm,primecell"; + gpio-controller; + reg = <0x20 0x10093000 0x00 0x1000>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + }; + }; +}; + +/* + Local Variables: + mode: C + End: +*/ diff --git a/arch/arm/boot/dts/intel/ixp/Makefile b/arch/arm/boot/dts/intel/ixp/Makefile new file mode 100644 index 000000000000..1a25ce3cf84f --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/Makefile @@ -0,0 +1,19 @@ +# SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_IXP4XX) += \ + intel-ixp42x-linksys-nslu2.dtb \ + intel-ixp42x-linksys-wrv54g.dtb \ + intel-ixp42x-freecom-fsg-3.dtb \ + intel-ixp42x-welltech-epbx100.dtb \ + intel-ixp42x-ixdp425.dtb \ + intel-ixp43x-kixrp435.dtb \ + intel-ixp46x-ixdp465.dtb \ + intel-ixp42x-adi-coyote.dtb \ + intel-ixp42x-ixdpg425.dtb \ + intel-ixp42x-goramo-multilink.dtb \ + intel-ixp42x-iomega-nas100d.dtb \ + intel-ixp42x-dlink-dsm-g600.dtb \ + intel-ixp42x-gateworks-gw2348.dtb \ + intel-ixp43x-gateworks-gw2358.dtb \ + intel-ixp42x-netgear-wg302v1.dtb \ + intel-ixp42x-arcom-vulcan.dtb \ + intel-ixp42x-gateway-7001.dtb diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts new file mode 100644 index 000000000000..765ab36e6f0c --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-adi-coyote.dts @@ -0,0 +1,112 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for ADI Engineering Coyote platform. + * Derived from boardfiles written by MontaVista software. + * Ethernet set-up from OpenWrt. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "ADI Engineering Coyote reference design"; + compatible = "adieng,coyote", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* CHECKME: 16 MB SDRAM minimum, maybe the Coyote actually has more */ + device_type = "memory"; + reg = <0x00000000 0x01000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* These are switched around */ + serial0 = &uart1; + serial1 = &uart0; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 32 MB of Flash in 128 0x20000 sized blocks + * mapped in at CS0 and CS1 + */ + reg = <0 0x00000000 0x2000000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + /* CHECKME: guess this is Redboot FIS */ + fis-index-block = <0x1ff>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Coyote PCI boardfile. + * We have slots (IDSEL) 1 and 2 with one assigned IRQ + * each handling all IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 6 */ + <0x0800 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 6 */ + <0x0800 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 6 */ + <0x0800 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 6 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ + <0x1000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 11 */ + <0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 11 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts new file mode 100644 index 000000000000..6f5b4e4eb1cc --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-arcom-vulcan.dts @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Arcom/Eurotech Vulcan board. + * This board is a single board computer in the PC/104 form factor based on + * IXP425, and was released around 2005. It previously had the name "Mercury". + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Arcom/Eurotech Vulcan"; + compatible = "arcom,vulcan", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + /* CHECKME: using a harddrive at /dev/sda1 as rootfs by default */ + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + onewire { + compatible = "w1-gpio"; + gpios = <&gpio0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 32 MB of Flash in 0x20000 byte blocks + * mapped in at CS0 and CS1. + * + * The documentation mentions the existence + * of a 16MB version, which we conveniently + * ignore. Shout if you own one! + */ + reg = <0 0x00000000 0x2000000>; + + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <3>; + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + fis-index-block = <0x1ff>; + }; + }; + sram@2,0 { + /* 256 KB SDRAM memory at CS2 */ + compatible = "shared-dma-pool"; + device_type = "memory"; + reg = <2 0x00000000 0x40000>; + no-map; + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <1>; + intel,ixp4xx-eb-t4 = <2>; + intel,ixp4xx-eb-ahb-split-transfers = <1>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + serial@3,0 { + /* + * 8250-compatible Exar XR16L2551 2 x UART + * + * CHECKME: if special tweaks are needed, then fix the + * operating system to handle it. + */ + compatible = "exar,xr16l2551", "ns8250"; + reg = <3 0x00000000 0x10>; + interrupt-parent = <&gpio0>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + clock-frequency = <1843200>; + /* Expansion bus settings */ + intel,ixp4xx-eb-t3 = <3>; + intel,ixp4xx-eb-cycle-type = <1>; /* Motorola cycles */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + gpio1: gpio@4,0 { + /* + * MMIO GPIO in one byte + */ + compatible = "arcom,vulcan-gpio"; + reg = <4 0x00000000 0x1>; + /* Expansion bus settings */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + watchdog@5,0 { + compatible = "maxim,max6369"; + reg = <5 0x00000000 0x1>; + /* Expansion bus settings */ + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Vulcan PCI boardfile. + * + * We have 2 slots (IDSEL) 1 and 2 with one dedicated interrupt + * per slot. This interrupt is shared (OR:ed) by all four pins. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 2 */ + <0x0800 0 0 2 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 2 */ + <0x0800 0 0 3 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 2 */ + <0x0800 0 0 4 &gpio0 2 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 2 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 3 */ + <0x1000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 3 */ + <0x1000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 3 */ + <0x1000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 3 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts new file mode 100644 index 000000000000..b9d46eb06507 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-dlink-dsm-g600.dts @@ -0,0 +1,147 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for D-Link DSM-G600 revision A based on IXP420 + * NOTE: revision B of this device uses PowerPC and is NOT supported by + * this device tree. + * + * Inspired by the boardfile by Rod Whitby, Tower Technologies, Alessandro Zummo + * and Michael Westerhof. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "D-Link DSM-G600 rev A"; + compatible = "dlink,dsm-g600-a", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-power { + label = "dsmg600:green:power"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-wlan { + label = "dsmg600:green:wlan"; + /* CHECKME: flagged as active low in the old board file */ + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + /* We don't have WLAN trigger in the kernel (yet) */ + linux,default-trigger = "netdev"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + }; + }; + + gpio_keys_polled { + compatible = "gpio-keys-polled"; + + /* + * According to the board file this key cannot handle interrupts and + * need to be polled. Investigate if this is really the case or if + * this can be moved adjacent to the ordinary gpio-keys above. + */ + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 16 MB of Flash in 128 0x20000 sized blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* + * A boot log says the directory is at 0xfe0000 + * 0x7f * 0x20000 = 0xfe0000 + */ + fis-index-block = <0x7f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from DSM-G600 PCI boardfile (dsmg600-pci.c) + * We have slots (IDSEL) 1, 2, 3, 4 and pins 1, 2 and 3. + * Only slot 3 have three IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT E on slot 1 is irq 7 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 10 */ + <0x1800 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 9 */ + <0x1800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 8 */ + /* IDSEL 4 */ + <0x2000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT F on slot 4 is irq 6 */ + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts new file mode 100644 index 000000000000..5a5e16cc7335 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-freecom-fsg-3.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Freecom FSG-3 router. + * This machine is based on IXP425. + * This device tree is inspired by the board file by Rod Whitby. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Freecom FSG-3"; + compatible = "freecom,fsg-3", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB memory */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + /* Boot from the first partition on the hard drive */ + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootfstype=ext4 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-sync { + wakeup-source; + /* Closest approximation of what the key should do */ + linux,code = <KEY_CONNECT>; + label = "sync"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + }; + button-usb { + wakeup-source; + /* Unplug USB, closest approximation of what the key should do */ + linux,code = <KEY_EJECTCD>; + label = "usb"; + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 12 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 13 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + /* + * Temperature sensor and fan control chip. + * + * TODO: create a proper device tree binding for + * the sensor and temperature zone and create a + * zone with fan control. + */ + compatible = "winbond,w83781d"; + reg = <0x28>; + }; + rtc@6f { + compatible = "isil,isl1208"; + reg = <0x6f>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 4 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x400000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x3e0000 */ + fis-index-block = <0x1f>; + }; + }; + + /* Small syscon with some LEDs at CS2 */ + syscon@2,0 { + compatible = "freecom,fsg-cs2-system-controller", "syscon"; + reg = <2 0x0 0x200>; + reg-io-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <2 0x0 0x0 0x200>; + + led@0,0 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x01>; + label = "fsg:blue:wlan"; + linux,default-trigger = "wlan"; + default-state = "on"; + }; + led@0,1 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x02>; + label = "fsg:blue:wan"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,2 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x04>; + label = "fsg:blue:sata"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,3 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x04>; + label = "fsg:blue:usb"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,4 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x08>; + label = "fsg:blue:sync"; + linux,default-trigger = ""; + default-state = "on"; + }; + led@0,5 { + compatible = "register-bit-led"; + reg = <0x00 0x02>; + mask = <0x10>; + label = "fsg:blue:ring"; + linux,default-trigger = ""; + default-state = "on"; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Written based on the FSG-3 PCI boardfile. + * We have slots 12, 13 & 14 (IDSEL) with one IRQ each. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 12 */ + <0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */ + <0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */ + <0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */ + <0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */ + /* IDSEL 13 */ + <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */ + <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */ + <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */ + <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */ + /* IDSEL 14 */ + <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */ + <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */ + <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */ + <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts new file mode 100644 index 000000000000..4d70f6afd13a --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateway-7001.dts @@ -0,0 +1,110 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Gateway 7001 AP based on IXP422 + * Derived from boardfiles written by Imre Kaloz + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Gateway 7001 AP"; + compatible = "gateway,7001", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* second UART is the primary console */ + serial0 = &uart1; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of flash + */ + reg = <0 0x00000000 0x800000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Gateway 7001 PCI boardfile (gateway7001-pci.c) + * We have slots (IDSEL) 1 and 2 with one assigned IRQ + * each handling all IRQs. + */ + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 11 */ + <0x0800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 11 */ + <0x0800 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 11 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 10 */ + <0x1000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 10 */ + <0x1000 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 10 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts new file mode 100644 index 000000000000..97e3f25bb210 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-gateworks-gw2348.dts @@ -0,0 +1,174 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Gateworks Avila GW2348 board. + * This machine is based on IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Gateworks Avila GW2348"; + compatible = "gateworks,gw2348", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-user { + label = "gw2348:green:user"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + compatible = "adi,ad7418"; + reg = <0x28>; + }; + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; + eeprom@51 { + compatible = "atmel,24c08"; + reg = <0x51>; + pagesize = <16>; + size = <1024>; + read-only; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + ide@1,0 { + compatible = "intel,ixp4xx-compact-flash"; + /* + * Set up expansion bus config to a really slow timing. + * The CF driver will dynamically reconfigure these timings + * depending on selected PIO mode (0-4). + */ + intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase + intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase + intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase + intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase + intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase + intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-mux-address-and-data = <0>; + intel,ixp4xx-eb-ahb-split-transfers = <0>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + /* First register set is CMD second is CTL (notice it uses CS2) */ + reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>; + interrupt-parent = <&gpio0>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + }; + /* + * FIXME: Latch LEDs or extra UARTs at CS4 + */ + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from Avila PCI boardfile. + * + * We have up to 4 slots (IDSEL) with 4 swizzled IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ + <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ + /* IDSEL 4 */ + <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */ + <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */ + <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */ + <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */ + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts new file mode 100644 index 000000000000..9ec0169bacf8 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-goramo-multilink.dts @@ -0,0 +1,180 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Goramo MultiLink Router + * There are two variants: + * - MultiLink Basic (a box) + * - MultiLink Max (19" rack mount) + * This device tree supports MultiLink Basic. + * This machine is based on IXP425. + * This is one of the few devices supporting the IXP4xx High-Speed Serial + * (HSS) link for a V.35 WAN interface. + * The hardware originates in Poland. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Goramo MultiLink Router"; + compatible = "goramo,multilink-router", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* + * 64 MB of RAM according to the manual. The MultiLink + * Max has 128 MB. + */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + }; + + /* + * 74HC4094 which is used as a rudimentary GPIO expander + * FIXME: + * - Create device tree bindings for this as GPIO expander + * - Write a pure DT GPIO driver using these bindings + * - Support cascading in the style of gpio-74x164.c (cannot be reused, very different) + */ + gpio_74: gpio-74hc4094 { + compatible = "nxp,74hc4094"; + cp-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + d-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + str-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; + /* oe-gpios is optional */ + gpio-controller; + #gpio-cells = <2>; + /* We are not cascaded */ + registers-number = <1>; + gpio-line-names = "CONTROL_HSS0_CLK_INT", "CONTROL_HSS1_CLK_INT", "CONTROL_HSS0_DTR_N", + "CONTROL_HSS1_DTR_N", "CONTROL_EXT", "CONTROL_AUTO_RESET", + "CONTROL_PCI_RESET_N", "CONTROL_EEPROM_WC_N"; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * The device has 4 slots (IDSEL) with one dedicated IRQ per slot. + * The slots have Ethernet, Ethernet, NEC and MPCI. + * The IDSELs are 11, 12, 13, 14. + */ + interrupt-map = + /* IDSEL 11 - Ethernet A */ + <0x5800 0 0 1 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 11 is irq 4 */ + <0x5800 0 0 2 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 11 is irq 4 */ + <0x5800 0 0 3 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 11 is irq 4 */ + <0x5800 0 0 4 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 11 is irq 4 */ + /* IDSEL 12 - Ethernet B */ + <0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */ + <0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */ + <0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */ + <0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */ + /* IDSEL 13 - MPCI */ + <0x6800 0 0 1 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 12 */ + <0x6800 0 0 2 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 12 */ + <0x6800 0 0 3 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 12 */ + <0x6800 0 0 4 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 12 */ + /* IDSEL 14 - NEC */ + <0x7000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 3 */ + <0x7000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 3 */ + <0x7000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 3 */ + <0x7000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 3 */ + }; + + /* HSS links */ + npe@c8006000 { + hss@0 { + status = "okay"; + intel,queue-chl-rxtrig = <&qmgr 12>; + intel,queue-chl-txready = <&qmgr 34>; + intel,queue-pkt-rx = <&qmgr 13>; + intel,queue-pkt-tx = <&qmgr 14>, <&qmgr 15>, <&qmgr 16>, <&qmgr 17>; + intel,queue-pkt-rxfree = <&qmgr 18>, <&qmgr 19>, <&qmgr 20>, <&qmgr 21>; + intel,queue-pkt-txdone = <&qmgr 22>; + /* The Goramo GPIO-based clock etc control */ + cts-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio_74 2 GPIO_ACTIVE_LOW>; + clk-internal-gpios = <&gpio_74 0 GPIO_ACTIVE_HIGH>; + }; + hss@1 { + status = "okay"; + intel,queue-chl-rxtrig = <&qmgr 10>; + intel,queue-chl-txready = <&qmgr 35>; + intel,queue-pkt-rx = <&qmgr 0>; + intel,queue-pkt-tx = <&qmgr 5>, <&qmgr 6>, <&qmgr 7>, <&qmgr 8>; + intel,queue-pkt-rxfree = <&qmgr 1>, <&qmgr 2>, <&qmgr 3>, <&qmgr 4>; + intel,queue-pkt-txdone = <&qmgr 9>; + /* The Goramo GPIO-based clock etc control */ + cts-gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + dcd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; + dtr-gpios = <&gpio_74 3 GPIO_ACTIVE_LOW>; + clk-internal-gpios = <&gpio_74 1 GPIO_ACTIVE_HIGH>; + }; + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 32>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 33>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts new file mode 100644 index 000000000000..8da6823e1dbe --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-iomega-nas100d.dts @@ -0,0 +1,148 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Iomega NAS 100D + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Iomega NAS 100D"; + compatible = "iom,nas-100d", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-wlan { + label = "nas100d:red:wlan"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + /* We don't have WLAN trigger in the kernel (yet) */ + linux,default-trigger = "netdev"; + }; + led-disk { + label = "nas100d:red:disk"; + gpios = <&gpio0 3 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "disk-activity"; + }; + led-power { + label = "nas100d:red:power"; + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 0x20000 byte blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from NAS 100D PCI boardfile (nas100d-pci.c) + * We have slots (IDSEL) 1, 2 and 3 and pins 1, 2 and 3. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>; /* INT C on slot 3 is irq 7 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts new file mode 100644 index 000000000000..194945748dc3 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdp425.dts @@ -0,0 +1,72 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel IXDP425 also known as IXCDP1100 Control Plane + * processor reference design. + * + * This platform has the codename "Richfield". + * + * This machine is based on a 533 MHz IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include "intel-ixp4xx-reference-design.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel IXDP425/IXCDP1100 Richfield Reference Design"; + compatible = "intel,ixdp425", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + }; + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts new file mode 100644 index 000000000000..7011fea6205b --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-ixdpg425.dts @@ -0,0 +1,127 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel IXDPG425 reference design. + * Derived from boardfiles written by MontaVista software. + * Ethernet set-up from OpenWrt. + * + * The device has 4 x FXS RJ11 ports for analog phones for + * internet telephony. (Not supported yet.) + * + * The device has 9 status LEDs we do not support yet. + * + * This device is very similar to ADI engingeering Coyote. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel IXDPG425 reference design"; + compatible = "intel,ixdpg425", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x02000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * CHECKME: the product brief says 16MB in a flash + * socket. + */ + reg = <0 0x00000000 0x1000000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + /* CHECKME: guess this is Redboot FIS */ + fis-index-block = <0x7f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from IXDPG425 PCI boardfile. + * We have slots (IDSEL) 12, 13 and 14 with one assigned IRQ + * for 12 & 13 and one for 14. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 12 */ + <0x6000 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 7 */ + <0x6000 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 7 */ + <0x6000 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 7 */ + <0x6000 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 7 */ + /* IDSEL 13 */ + <0x6800 0 0 1 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 7 */ + <0x6800 0 0 2 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 7 */ + <0x6800 0 0 3 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 7 */ + <0x6800 0 0 4 &gpio0 7 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 7 */ + /* IDSEL 14 */ + <0x7000 0 0 1 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 6 */ + <0x7000 0 0 2 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 6 */ + <0x7000 0 0 3 &gpio0 6 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 6 */ + <0x7000 0 0 4 &gpio0 6 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 6 */ + }; + + /* + * CHECKME: this ethernet setup seems dubious. Photos of the board shows some kind + * of Realtek DSA switch on the board. + */ + + /* EthB */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy4: ethernet-phy@4 { + reg = <4>; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts new file mode 100644 index 000000000000..da1e93212b86 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-nslu2.dts @@ -0,0 +1,162 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Linksys NSLU2 + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys NSLU2 (Network Storage Link for USB 2.0 Disk Drives)"; + compatible = "linksys,nslu2", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-status { + label = "nslu2:red:status"; + gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-ready { + label = "nslu2:green:ready"; + gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + led-disk-1 { + label = "nslu2:green:disk-1"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + led-disk-2 { + label = "nslu2:green:disk-2"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-power { + wakeup-source; + linux,code = <KEY_POWER>; + label = "power"; + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + }; + button-reset { + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@6f { + compatible = "xicor,x1205"; + reg = <0x6f>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>; + timeout-ms = <5000>; + }; + + gpio-beeper { + compatible = "gpio-beeper"; + gpios = <&gpio0 4 GPIO_ACTIVE_HIGH>; + }; + + soc { + bus@c4000000 { + /* The first 16MB region at CS0 on the expansion bus */ + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 0x20000 byte blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x7e0000 */ + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from NSLU2 PCI boardfile, INT A, B, C swizzled D constant + * We have slots (IDSEL) 1, 2 and 3. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 11 */ + <0x1000 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 8 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x1800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x1800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 8 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts new file mode 100644 index 000000000000..4aba9e0214a0 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-linksys-wrv54g.dts @@ -0,0 +1,175 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Linksys WRV54G router + * Also known as Gemtek GTWX5715 + * Based on a board file by George T. Joseph and other patches. + * This machine is based on IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys WRV54G / Gemtek GTWX5715"; + compatible = "linksys,wrv54g", "gemtek,gtwx5715", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB memory */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* UART2 is the primary console */ + serial0 = &uart1; + serial1 = &uart0; + }; + + /* There is an unpopulated LED slot (3) connected to GPIO 8 */ + leds { + compatible = "gpio-leds"; + led-power { + label = "wrv54g:yellow:power"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-wireless { + label = "wrv54g:yellow:wireless"; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led-internet { + label = "wrv54g:yellow:internet"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led-dmz { + label = "wrv54g:green:dmz"; + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + /* This set-up comes from an OpenWrt patch */ + spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + num-chipselects = <1>; + + switch@0 { + compatible = "micrel,ks8995"; + reg = <0>; + spi-max-frequency = <50000000>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 8 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x00800000>; + + partitions { + compatible = "fixed-partitions"; + /* + * Partition info from a boot log + * CHECKME: not using redboot? FIS index 0x3f @7e00000? + */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "boot"; + reg = <0x0 0x140000>; + read-only; + }; + partition@140000 { + label = "linux"; + reg = <0x140000 0x100000>; + read-only; + }; + partition@240000 { + label = "root"; + reg = <0x240000 0x480000>; + read-write; + }; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * We have up to 2 slots (IDSEL) with 2 swizzled IRQs. + * Derived from the GTWX5715 PCI boardfile. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 0 */ + <0x0000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 0 is irq 10 */ + <0x0000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 0 is irq 11 */ + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 1 is irq 10 */ + }; + + /* + * EthB - connected to the KS8995 switch ports 1-4 + * FIXME: the boardfile defines .phy_mask = 0x1e for this port to enable output to + * all four switch ports, also using an out of tree multiphy patch. + * Do we need a new binding and property for this? + */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Should be ports 1-4 on the KS8995 switch */ + phy4: ethernet-phy@4 { + reg = <4>; + }; + + /* Should be port 5 on the KS8995 switch */ + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC - connected to KS8995 switch port 5 */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts new file mode 100644 index 000000000000..19d56e9aec9d --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-netgear-wg302v1.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Netgear WG302v2 based on IXP422BB + * Derived from boardfiles written by Imre Kaloz + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Netgear WG302 v1"; + compatible = "netgear,wg302v1", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB SDRAM according to boot arguments */ + device_type = "memory"; + reg = <0x00000000 0x02000000>; + }; + + chosen { + /* The RedBoot comes up in 9600 baud so let's keep this */ + bootargs = "console=ttyS0,9600n8"; + stdout-path = "uart1:9600n8"; + }; + + aliases { + /* These are switched around */ + serial0 = &uart1; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 8 MB of Flash in 64 0x20000 sized blocks + * mapped in at CS0. + */ + reg = <0 0x00000000 0x800000>; + + /* Configure expansion bus to allow writes */ + intel,ixp4xx-eb-write-enable = <1>; + + partitions { + compatible = "redboot-fis"; + fis-index-block = <0x3f>; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c) + * We have slots (IDSEL) 1 and 2 with one assigned IRQ + * each handling all IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */ + <0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */ + <0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */ + <0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */ + }; + + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy30>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy30: ethernet-phy@30 { + reg = <30>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts new file mode 100644 index 000000000000..c550c421b659 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x-welltech-epbx100.dts @@ -0,0 +1,98 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Corentin Labbe <clabbe@baylibre.com> + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" + +/ { + model = "Welltech EPBX100"; + compatible = "welltech,epbx100", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 64 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/ram0 initrd=0x00800000,9M"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* + * 16 MB of Flash + */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "RedBoot"; + reg = <0x00000000 0x00080000>; + read-only; + }; + partition@80000 { + label = "zImage"; + reg = <0x00080000 0x00100000>; + read-only; + }; + partition@180000 { + label = "ramdisk"; + reg = <0x00180000 0x00300000>; + read-only; + }; + partition@480000 { + label = "User"; + reg = <0x00480000 0x00b60000>; + read-only; + }; + partition@fe0000 { + label = "FIS directory"; + reg = <0x00fe0000 0x001f000>; + read-only; + }; + partition@fff000 { + label = "RedBoot config"; + reg = <0x00fff000 0x0001000>; + read-only; + }; + }; + }; + }; + + /* LAN port */ + ethernet@c8009000 { + status = "okay"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi new file mode 100644 index 000000000000..84cee8ec3ab8 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp42x.dtsi @@ -0,0 +1,34 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP 42x series. This series has 32 interrupts. + */ +#include "intel-ixp4xx.dtsi" + +/ { + soc { + bus@c4000000 { + compatible = "intel,ixp42x-expansion-bus-controller", "syscon"; + reg = <0xc4000000 0x30>; + }; + + pci@c0000000 { + compatible = "intel,ixp42x-pci"; + }; + + interrupt-controller@c8003000 { + compatible = "intel,ixp42x-interrupt"; + }; + + /* + * This is the USB Device Mode (UDC) controller, which is used + * to present the IXP4xx as a device on a USB bus. + */ + usb@c800b000 { + compatible = "intel,ixp4xx-udc"; + reg = <0xc800b000 0x1000>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts new file mode 100644 index 000000000000..1db849515f9e --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-gateworks-gw2358.dts @@ -0,0 +1,199 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Gateworks IXP43x-based Cambria GW2358 + */ + +/dts-v1/; + +#include "intel-ixp43x.dtsi" + +/ { + model = "Gateworks Cambria GW2358"; + compatible = "gateworks,gw2358", "intel,ixp43x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 128 MB SDRAM */ + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 root=/dev/mtdblock2 rw rootfstype=squashfs,jffs2 rootwait"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + leds { + compatible = "gpio-leds"; + led-user { + label = "gw2358:green:LED"; + gpios = <&pld1 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + }; + + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + hwmon@28 { + compatible = "adi,ad7418"; + reg = <0x28>; + }; + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; + eeprom@51 { + compatible = "atmel,24c08"; + reg = <0x51>; + pagesize = <16>; + size = <1024>; + read-only; + }; + pld0: pld@56 { + compatible = "gateworks,pld-gpio"; + reg = <0x56>; + gpio-controller; + #gpio-cells = <2>; + }; + /* This PLD just handles the LED and user button */ + pld1: pld@57 { + compatible = "gateworks,pld-gpio"; + reg = <0x57>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* + * 32 MB of Flash in 0x20000 byte blocks + * mapped in at CS0 and CS1 + */ + reg = <0 0x00000000 0x2000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x1fe0000 */ + fis-index-block = <0xff>; + }; + }; + ide@3,0 { + compatible = "intel,ixp4xx-compact-flash"; + /* + * Set up expansion bus config to a really slow timing. + * The CF driver will dynamically reconfigure these timings + * depending on selected PIO mode (0-4). + */ + intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase + intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase + intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase + intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase + intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase + intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type + intel,ixp4xx-eb-byte-access-on-halfword = <1>; + intel,ixp4xx-eb-mux-address-and-data = <0>; + intel,ixp4xx-eb-ahb-split-transfers = <0>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + /* First register set is CMD second is CTL */ + reg = <3 0xe00000 0x40000>, <3 0xe40000 0x40000>; + interrupt-parent = <&gpio0>; + interrupts = <12 IRQ_TYPE_EDGE_RISING>; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * In the boardfile for the Cambria from OpenWRT the interrupts + * are assigned one per IDSEL, so all 4 interrupts from IDSEL + * 1 are connected to IRQ 11, all 4 interrupts from IDSEL 2 + * connected to IRQ 10 etc. I find this highly unlikely so I + * have instead assumed that they are rotated (swizzled) like + * this with 11, 10, 9, 8 for the 4 pins on IDSEL 1 etc. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ + <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ + /* IDSEL 4 */ + <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */ + <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 9 */ + /* IDSEL 6 */ + <0x3000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 10 */ + <0x3000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 9 */ + <0x3000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 8 */ + <0x3000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 11 */ + /* IDSEL 15 */ + <0x7800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 8 */ + <0x7800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 11 */ + <0x7800 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 10 */ + <0x7800 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 3 is irq 9 */ + }; + + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; + }; + + ethernet@c800c000 { + status = "okay"; + queue-rx = <&qmgr 2>; + queue-txready = <&qmgr 19>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + intel,npe-handle = <&npe 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts new file mode 100644 index 000000000000..4703a8b24765 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x-kixrp435.dts @@ -0,0 +1,68 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel KIXRP435 Control Plane + * processor reference design. + */ + +/dts-v1/; + +#include "intel-ixp43x.dtsi" +#include "intel-ixp4xx-reference-design.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel KIXRP435 Reference Design"; + compatible = "intel,kixrp435", "intel,ixp43x"; + #address-cells = <1>; + #size-cells = <1>; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 16 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x1000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x0fe0000 */ + fis-index-block = <0x7f>; + }; + }; + }; + + /* CHECKME: ethernet set-up taken from Gateworks Cambria */ + ethernet@c800a000 { + status = "okay"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; + }; + + ethernet@c800c000 { + status = "okay"; + queue-rx = <&qmgr 2>; + queue-txready = <&qmgr 19>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + intel,npe-handle = <&npe 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi new file mode 100644 index 000000000000..60bf9903e0f8 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp43x.dtsi @@ -0,0 +1,25 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP 43x series. This series has 64 interrupts and adds a few more + * peripherals over the 42x series. + */ +#include "intel-ixp4xx.dtsi" + +/ { + soc { + bus@c4000000 { + compatible = "intel,ixp43x-expansion-bus-controller", "syscon"; + /* Uses at least up to 0x230 */ + reg = <0xc4000000 0x1000>; + }; + + pci@c0000000 { + compatible = "intel,ixp43x-pci"; + }; + + interrupt-controller@c8003000 { + compatible = "intel,ixp43x-interrupt"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi new file mode 100644 index 000000000000..1dd4a65cb7a6 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp45x-ixp46x.dtsi @@ -0,0 +1,86 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP45x and IXP46x series. This series has 64 interrupts and adds a + * few more peripherals over the 42x and 43x series so this extends the + * basic IXP4xx DTSI. + */ +#include "intel-ixp4xx.dtsi" + +/ { + soc { + bus@c4000000 { + compatible = "intel,ixp46x-expansion-bus-controller", "syscon"; + /* Uses at least up to 0x124 */ + reg = <0xc4000000 0x1000>; + }; + + rng@70002100 { + compatible = "intel,ixp46x-rng"; + reg = <0x70002100 4>; + }; + + interrupt-controller@c8003000 { + compatible = "intel,ixp43x-interrupt"; + }; + + /* + * This is the USB Device Mode (UDC) controller, which is used + * to present the IXP4xx as a device on a USB bus. + */ + usb@c800b000 { + compatible = "intel,ixp4xx-udc"; + reg = <0xc800b000 0x1000>; + interrupts = <12 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + i2c@c8011000 { + compatible = "intel,ixp4xx-i2c"; + reg = <0xc8011000 0x18>; + interrupts = <33 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + }; + + /* This is known as EthB1 */ + ethernet@c800d000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800d000 0x1000>; + status = "disabled"; + intel,npe = <1>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + + /* This is known as EthB2 */ + ethernet@c800e000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800e000 0x1000>; + status = "disabled"; + intel,npe = <2>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + + /* This is known as EthB3 */ + ethernet@c800f000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800f000 0x1000>; + status = "disabled"; + intel,npe = <3>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + + ptp-timer@c8010000 { + compatible = "intel,ixp46x-ptp-timer"; + reg = <0xc8010000 0x1000>; + interrupt-parent = <&gpio0>; + interrupts = <8 IRQ_TYPE_EDGE_FALLING>, <7 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "master", "slave"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts new file mode 100644 index 000000000000..a062cd1a6588 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp46x-ixdp465.dts @@ -0,0 +1,38 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Intel IXDP465 Control Plane processor reference + * design, codename "BMP". + */ + +/dts-v1/; + +#include "intel-ixp45x-ixp46x.dtsi" +#include "intel-ixp4xx-reference-design.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Intel IXDP465 BMP Reference Design"; + compatible = "intel,ixdp465", "intel,ixp46x"; + #address-cells = <1>; + #size-cells = <1>; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 32 MB of Flash mapped in at CS0 and CS1 */ + reg = <0 0x00000000 0x2000000>; + + partitions { + compatible = "redboot-fis"; + /* Eraseblock at 0x1fe0000 */ + fis-index-block = <0xff>; + }; + }; + }; + /* TODO: configure ethernet etc */ + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi new file mode 100644 index 000000000000..31c0a69771c4 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx-reference-design.dtsi @@ -0,0 +1,134 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree include file for Intel reference designs for the + * XScale Network Processors in the IXP 4xx series. Common device + * set-up for IXDP425, IXCDP1100, KIXRP435 and IXDP465. + */ + +/ { + memory@0 { + /* + * The board supports up to 256 MB of memory. Here we put in + * 64 MB and this may be modified by the boot loader. + */ + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart0:115200n8"; + }; + + aliases { + serial0 = &uart0; + }; + + i2c { + compatible = "i2c-gpio"; + sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@50 { + /* + * Philips PCF8582C-2T/03 512byte I2C EEPROM + * should behave like an Atmel 24c04. + */ + compatible = "atmel,24c04"; + reg = <0x50>; + pagesize = <16>; + size = <512>; + read-only; + }; + }; + + soc { + bus@c4000000 { + /* Flash memory defined per-variant */ + nand-controller@3,0 { + /* Some designs have a NAND on CS3 enable it here if present */ + status = "disabled"; + + /* + * gen_nand needs to be extended and documented to get + * command byte = 1 and address byte = 2 from the device + * tree. + */ + compatible = "gen_nand"; + + /* Expansion bus set-up */ + intel,ixp4xx-eb-t1 = <0>; + intel,ixp4xx-eb-t2 = <0>; + intel,ixp4xx-eb-t3 = <1>; // 1 cycle extra strobe phase + intel,ixp4xx-eb-t4 = <0>; + intel,ixp4xx-eb-t5 = <0>; + intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type + intel,ixp4xx-eb-byte-access-on-halfword = <0>; + intel,ixp4xx-eb-mux-address-and-data = <0>; + intel,ixp4xx-eb-ahb-split-transfers = <0>; + intel,ixp4xx-eb-write-enable = <1>; + intel,ixp4xx-eb-byte-access = <1>; + + /* 512 bytes memory window */ + reg = <3 0x00000000 0x200>; + nand-on-flash-bbt; + nand-ecc-mode = "soft_bch"; + nand-ecc-step-size = <512>; + nand-ecc-strength = <4>; + nce-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* NCE */ + + label = "ixp400 NAND"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + fs@0 { + label = "ixp400 NAND FS 0"; + reg = <0x0 0x800000>; + }; + fs@800000 { + label = "ixp400 NAND FS 1"; + reg = <0x800000 0x0>; + }; + }; + }; + }; + + pci@c0000000 { + status = "okay"; + + /* + * Taken from IXDP425 PCI boardfile. + * PCI slots on the BIXMB425BD base card. + * We have up to 4 slots (IDSEL) with 4 swizzled IRQs. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */ + <0x0800 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */ + <0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */ + /* IDSEL 2 */ + <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */ + <0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */ + <0x1000 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */ + <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */ + /* IDSEL 3 */ + <0x1800 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */ + <0x1800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */ + <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */ + <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */ + /* IDSEL 4 */ + <0x2000 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */ + <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */ + <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */ + <0x2000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */ + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi new file mode 100644 index 000000000000..51a716c59669 --- /dev/null +++ b/arch/arm/boot/dts/intel/ixp/intel-ixp4xx.dtsi @@ -0,0 +1,202 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for Intel XScale Network Processors + * in the IXP 4xx series. + */ +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + soc { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "simple-bus"; + interrupt-parent = <&intcon>; + + /* + * The IXP4xx expansion bus is a set of up to 7 each up to 16MB + * windows in the 256MB space from 0x50000000 to 0x5fffffff. + */ + bus@c4000000 { + /* compatible and reg filled in by per-soc device tree */ + native-endian; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0x0 0x50000000 0x01000000>, + <1 0x0 0x51000000 0x01000000>, + <2 0x0 0x52000000 0x01000000>, + <3 0x0 0x53000000 0x01000000>, + <4 0x0 0x54000000 0x01000000>, + <5 0x0 0x55000000 0x01000000>, + <6 0x0 0x56000000 0x01000000>, + <7 0x0 0x57000000 0x01000000>; + dma-ranges = <0 0x0 0x50000000 0x01000000>, + <1 0x0 0x51000000 0x01000000>, + <2 0x0 0x52000000 0x01000000>, + <3 0x0 0x53000000 0x01000000>, + <4 0x0 0x54000000 0x01000000>, + <5 0x0 0x55000000 0x01000000>, + <6 0x0 0x56000000 0x01000000>, + <7 0x0 0x57000000 0x01000000>; + }; + + qmgr: queue-manager@60000000 { + compatible = "intel,ixp4xx-ahb-queue-manager"; + reg = <0x60000000 0x4000>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>, <4 IRQ_TYPE_LEVEL_HIGH>; + }; + + pci@c0000000 { + /* compatible filled in by per-soc device tree */ + reg = <0xc0000000 0x1000>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, + <9 IRQ_TYPE_LEVEL_HIGH>, + <10 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0x00 0xff>; + status = "disabled"; + + ranges = + /* + * 64MB 32bit non-prefetchable memory 0x48000000-0x4bffffff + * done in 4 chunks of 16MB each. + */ + <0x02000000 0 0x48000000 0x48000000 0 0x04000000>, + /* 64KB I/O space at 0x4c000000 */ + <0x01000000 0 0x00000000 0x4c000000 0 0x00010000>; + + /* + * This needs to map to the start of physical memory so + * PCI devices can see all (hopefully) memory. This is done + * using 4 1:1 16MB windows, so the RAM should not be more than + * 64 MB for this to work. If your memory is anywhere else + * than at 0x0 you need to alter this. + */ + dma-ranges = + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>; + + /* Each unique DTS using PCI must specify the swizzling */ + }; + + uart0: serial@c8000000 { + compatible = "intel,xscale-uart"; + reg = <0xc8000000 0x1000>; + /* + * The reg-offset and reg-shift is a side effect + * of running the platform in big endian mode. + */ + reg-offset = <3>; + reg-shift = <2>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <14745600>; + no-loopback-test; + }; + + uart1: serial@c8001000 { + compatible = "intel,xscale-uart"; + reg = <0xc8001000 0x1000>; + /* + * The reg-offset and reg-shift is a side effect + * of running the platform in big endian mode. + */ + reg-offset = <3>; + reg-shift = <2>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <14745600>; + no-loopback-test; + }; + + gpio0: gpio@c8004000 { + compatible = "intel,ixp4xx-gpio"; + reg = <0xc8004000 0x1000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + intcon: interrupt-controller@c8003000 { + /* + * Note: no compatible string. The subvariant of the + * chip needs to define what version it is. The + * location of the interrupt controller is fixed in + * memory across all variants. + */ + reg = <0xc8003000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + timer@c8005000 { + compatible = "intel,ixp4xx-timer"; + reg = <0xc8005000 0x100>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + }; + + npe: npe@c8006000 { + compatible = "intel,ixp4xx-network-processing-engine"; + reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + /* NPE-A contains two high-speed serial links */ + hss@0 { + compatible = "intel,ixp4xx-hss"; + reg = <0>; + intel,npe-handle = <&npe 0>; + status = "disabled"; + }; + + hss@1 { + compatible = "intel,ixp4xx-hss"; + reg = <1>; + intel,npe-handle = <&npe 0>; + status = "disabled"; + }; + + /* NPE-C contains a crypto accelerator */ + crypto { + compatible = "intel,ixp4xx-crypto"; + intel,npe-handle = <&npe 2>; + queue-rx = <&qmgr 30>; + queue-txready = <&qmgr 29>; + }; + }; + + /* This is known as EthB */ + ethernet@c8009000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc8009000 0x1000>; + status = "disabled"; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + intel,npe-handle = <&npe 1>; + }; + + /* This is known as EthC */ + ethernet@c800a000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800a000 0x1000>; + status = "disabled"; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + intel,npe-handle = <&npe 2>; + }; + + /* This is known as EthA */ + ethernet@c800c000 { + compatible = "intel,ixp4xx-ethernet"; + reg = <0xc800c000 0x1000>; + status = "disabled"; + intel,npe = <0>; + /* Dummy values that depend on firmware */ + queue-rx = <&qmgr 0>; + queue-txready = <&qmgr 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/Makefile b/arch/arm/boot/dts/intel/pxa/Makefile new file mode 100644 index 000000000000..24d5240f08e7 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/Makefile @@ -0,0 +1,8 @@ +# SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_PXA) += \ + pxa300-raumfeld-connector.dtb \ + pxa300-raumfeld-controller.dtb \ + pxa300-raumfeld-speaker-l.dtb \ + pxa300-raumfeld-speaker-m.dtb \ + pxa300-raumfeld-speaker-one.dtb \ + pxa300-raumfeld-speaker-s.dtb diff --git a/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi b/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi new file mode 100644 index 000000000000..5f8300e356ad --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa25x.dtsi @@ -0,0 +1,118 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright (C) 2016 Robert Jarzmik <robert.jarzmik@free.fr> + */ +#include "pxa2xx.dtsi" +#include "dt-bindings/clock/pxa-clock.h" + +/ { + model = "Marvell PXA25x family SoC"; + compatible = "marvell,pxa250"; + + clocks { + /* + * The muxing of external clocks/internal dividers for osc* clock + * sources has been hidden under the carpet by now. + */ + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clks: pxa2xx_clks@41300004 { + compatible = "marvell,pxa250-core-clocks"; + #clock-cells = <1>; + status = "okay"; + }; + + /* timer oscillator */ + clktimer: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <3686400>; + clock-output-names = "ostimer"; + }; + }; + + pxabus { + pdma: dma-controller@40000000 { + compatible = "marvell,pdma-1.0"; + reg = <0x40000000 0x10000>; + interrupts = <25>; + #dma-cells = <2>; + /* For backwards compatibility: */ + #dma-channels = <16>; + dma-channels = <16>; + #dma-requests = <40>; + dma-requests = <40>; + status = "okay"; + }; + + pxairq: interrupt-controller@40d00000 { + marvell,intc-priority; + marvell,intc-nr-irqs = <32>; + }; + + pinctrl: pinctrl@40e00000 { + reg = <0x40e00054 0x20 0x40e0000c 0xc 0x40e0010c 4 + 0x40f00020 0x10>; + compatible = "marvell,pxa25x-pinctrl"; + }; + + gpio: gpio@40e00000 { + compatible = "intel,pxa25x-gpio"; + gpio-ranges = <&pinctrl 0 0 84>; + clocks = <&clks CLK_NONE>; + }; + + pwm0: pwm@40b00000 { + compatible = "marvell,pxa250-pwm"; + reg = <0x40b00000 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM0>; + }; + + pwm1: pwm@40b00010 { + compatible = "marvell,pxa250-pwm"; + reg = <0x40b00010 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM1>; + }; + + rtc@40900000 { + clocks = <&clks CLK_OSC32k768>; + }; + }; + + timer@40a00000 { + compatible = "marvell,pxa-timer"; + reg = <0x40a00000 0x20>; + interrupts = <26>; + clocks = <&clktimer>; + status = "okay"; + }; + + pxa250_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp-99532800 { + opp-hz = /bits/ 64 <99532800>; + opp-microvolt = <1000000 950000 1650000>; + clock-latency-ns = <20>; + }; + opp-199065600 { + opp-hz = /bits/ 64 <199065600>; + opp-microvolt = <1000000 950000 1650000>; + clock-latency-ns = <20>; + }; + opp-298598400 { + opp-hz = /bits/ 64 <298598400>; + opp-microvolt = <1100000 1045000 1650000>; + clock-latency-ns = <20>; + }; + opp-398131200 { + opp-hz = /bits/ 64 <398131200>; + opp-microvolt = <1300000 1235000 1650000>; + clock-latency-ns = <20>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi b/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi new file mode 100644 index 000000000000..a2cbfb3be609 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa27x.dtsi @@ -0,0 +1,188 @@ +// SPDX-License-Identifier: GPL-2.0 +/* The pxa3xx skeleton simply augments the 2xx version */ +#include "pxa2xx.dtsi" +#include "dt-bindings/clock/pxa-clock.h" + +/ { + model = "Marvell PXA27x familiy SoC"; + compatible = "marvell,pxa27x"; + + pxabus { + pdma: dma-controller@40000000 { + compatible = "marvell,pdma-1.0"; + reg = <0x40000000 0x10000>; + interrupts = <25>; + #dma-cells = <2>; + /* For backwards compatibility: */ + #dma-channels = <32>; + dma-channels = <32>; + #dma-requests = <75>; + dma-requests = <75>; + status = "okay"; + }; + + pxairq: interrupt-controller@40d00000 { + marvell,intc-priority; + marvell,intc-nr-irqs = <34>; + }; + + pinctrl: pinctrl@40e00000 { + reg = <0x40e00054 0x20 0x40e0000c 0xc 0x40e0010c 4 + 0x40f00020 0x10>; + compatible = "marvell,pxa27x-pinctrl"; + }; + + gpio: gpio@40e00000 { + compatible = "intel,pxa27x-gpio"; + gpio-ranges = <&pinctrl 0 0 128>; + clocks = <&clks CLK_NONE>; + }; + + usb0: usb@4c000000 { + compatible = "marvell,pxa-ohci"; + reg = <0x4c000000 0x10000>; + interrupts = <3>; + clocks = <&clks CLK_USBHOST>; + status = "disabled"; + }; + + pwm0: pwm@40b00000 { + compatible = "marvell,pxa270-pwm", "marvell,pxa250-pwm"; + reg = <0x40b00000 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM0>; + }; + + pwm1: pwm@40b00010 { + compatible = "marvell,pxa270-pwm", "marvell,pxa250-pwm"; + reg = <0x40b00010 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM1>; + }; + + pwm2: pwm@40c00000 { + compatible = "marvell,pxa270-pwm", "marvell,pxa250-pwm"; + reg = <0x40c00000 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM0>; + }; + + pwm3: pwm@40c00010 { + compatible = "marvell,pxa270-pwm", "marvell,pxa250-pwm"; + reg = <0x40c00010 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM1>; + }; + + pwri2c: i2c@40f00180 { + compatible = "mrvl,pxa-i2c"; + reg = <0x40f00180 0x24>; + interrupts = <6>; + clocks = <&clks CLK_PWRI2C>; + #address-cells = <0x1>; + #size-cells = <0>; + status = "disabled"; + }; + + pxa27x_udc: udc@40600000 { + compatible = "marvell,pxa270-udc"; + reg = <0x40600000 0x10000>; + interrupts = <11>; + clocks = <&clks CLK_USB>; + status = "disabled"; + }; + + keypad: keypad@41500000 { + compatible = "marvell,pxa27x-keypad"; + reg = <0x41500000 0x4c>; + interrupts = <4>; + clocks = <&clks CLK_KEYPAD>; + status = "disabled"; + }; + + pxa_camera: imaging@50000000 { + compatible = "marvell,pxa270-qci"; + reg = <0x50000000 0x1000>; + interrupts = <33>; + dmas = <&pdma 68 0 /* Y channel */ + &pdma 69 0 /* U channel */ + &pdma 70 0>; /* V channel */ + dma-names = "CI_Y", "CI_U", "CI_V"; + + clocks = <&clks CLK_CAMERA>; + clock-names = "ciclk"; + clock-frequency = <5000000>; + clock-output-names = "qci_mclk"; + + status = "disabled"; + }; + + rtc@40900000 { + clocks = <&clks CLK_OSC32k768>; + }; + }; + + clocks { + /* + * The muxing of external clocks/internal dividers for osc* clock + * sources has been hidden under the carpet by now. + */ + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clks: pxa2xx_clks@41300004 { + compatible = "marvell,pxa270-clocks"; + #clock-cells = <1>; + status = "okay"; + }; + }; + + timer@40a00000 { + compatible = "marvell,pxa-timer"; + reg = <0x40a00000 0x20>; + interrupts = <26>; + clocks = <&clks CLK_OSTIMER>; + status = "okay"; + }; + + pxa270_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp-104000000 { + opp-hz = /bits/ 64 <104000000>; + opp-microvolt = <900000 900000 1705000>; + clock-latency-ns = <20>; + }; + opp-156000000 { + opp-hz = /bits/ 64 <156000000>; + opp-microvolt = <1000000 1000000 1705000>; + clock-latency-ns = <20>; + }; + opp-208000000 { + opp-hz = /bits/ 64 <208000000>; + opp-microvolt = <1180000 1180000 1705000>; + clock-latency-ns = <20>; + }; + opp-312000000 { + opp-hz = /bits/ 64 <312000000>; + opp-microvolt = <1250000 1250000 1705000>; + clock-latency-ns = <20>; + }; + opp-416000000 { + opp-hz = /bits/ 64 <416000000>; + opp-microvolt = <1350000 1350000 1705000>; + clock-latency-ns = <20>; + }; + opp-520000000 { + opp-hz = /bits/ 64 <520000000>; + opp-microvolt = <1450000 1450000 1705000>; + clock-latency-ns = <20>; + }; + opp-624000000 { + opp-hz = /bits/ 64 <624000000>; + opp-microvolt = <1550000 1550000 1705000>; + clock-latency-ns = <20>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi b/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi new file mode 100644 index 000000000000..84154c43fe65 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa2xx.dtsi @@ -0,0 +1,162 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * pxa2xx.dtsi - Device Tree Include file for Marvell PXA2xx family SoC + * + * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com> + */ + +#include "dt-bindings/clock/pxa-clock.h" + +#define PMGROUP(pin) #pin +#define PMMUX(func, pin, af) \ + mux- ## func { \ + groups = PMGROUP(P ## pin); \ + function = #af; \ + } +#define PMMUX_LPM_LOW(func, pin, af) \ + mux- ## func { \ + groups = PMGROUP(P ## pin); \ + function = #af; \ + low-power-disable; \ + } +#define PMMUX_LPM_HIGH(func, pin, af) \ + mux- ## func { \ + groups = PMGROUP(P ## pin); \ + function = #af; \ + low-power-enable; \ + } + +/ { + #address-cells = <1>; + #size-cells = <1>; + model = "Marvell PXA2xx family SoC"; + compatible = "marvell,pxa2xx"; + interrupt-parent = <&pxairq>; + + aliases { + serial0 = &ffuart; + serial1 = &btuart; + serial2 = &stuart; + serial3 = &hwuart; + i2c0 = &pwri2c; + i2c1 = &pxai2c1; + }; + + cpus { + cpu { + compatible = "marvell,xscale"; + device_type = "cpu"; + }; + }; + + pxabus { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pxairq: interrupt-controller@40d00000 { + #interrupt-cells = <1>; + compatible = "marvell,pxa-intc"; + interrupt-controller; + interrupt-parent; + marvell,intc-nr-irqs = <32>; + reg = <0x40d00000 0xd0>; + }; + + gpio: gpio@40e00000 { + compatible = "mrvl,pxa-gpio"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0x40e00000 0x10000>; + gpio-controller; + #gpio-cells = <0x2>; + interrupts = <8>, <9>, <10>; + interrupt-names = "gpio0", "gpio1", "gpio_mux"; + interrupt-controller; + #interrupt-cells = <0x2>; + ranges; + + gcb0: gpio@40e00000 { + reg = <0x40e00000 0x4>; + }; + + gcb1: gpio@40e00004 { + reg = <0x40e00004 0x4>; + }; + + gcb2: gpio@40e00008 { + reg = <0x40e00008 0x4>; + }; + gcb3: gpio@40e0000c { + reg = <0x40e0000c 0x4>; + }; + }; + + ffuart: serial@40100000 { + compatible = "mrvl,pxa-uart"; + reg = <0x40100000 0x30>; + interrupts = <22>; + clocks = <&clks CLK_FFUART>; + status = "disabled"; + }; + + btuart: serial@40200000 { + compatible = "mrvl,pxa-uart"; + reg = <0x40200000 0x30>; + interrupts = <21>; + clocks = <&clks CLK_BTUART>; + status = "disabled"; + }; + + stuart: serial@40700000 { + compatible = "mrvl,pxa-uart"; + reg = <0x40700000 0x30>; + interrupts = <20>; + clocks = <&clks CLK_STUART>; + status = "disabled"; + }; + + hwuart: serial@41600000 { + compatible = "mrvl,pxa-uart"; + reg = <0x41600000 0x30>; + interrupts = <7>; + status = "disabled"; + }; + + pxai2c1: i2c@40301680 { + compatible = "mrvl,pxa-i2c"; + reg = <0x40301680 0x30>; + interrupts = <18>; + clocks = <&clks CLK_I2C>; + #address-cells = <0x1>; + #size-cells = <0>; + status = "disabled"; + }; + + mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + clocks = <&clks CLK_MMC>; + dmas = <&pdma 21 3 + &pdma 22 3>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + rtc@40900000 { + compatible = "marvell,pxa-rtc"; + reg = <0x40900000 0x3c>; + interrupts = <30 31>; + }; + + lcdc: lcd-controller@40500000 { + compatible = "marvell,pxa2xx-lcdc"; + reg = <0x44000000 0x10000>; + interrupts = <17>; + clocks = <&clks CLK_LCD>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi new file mode 100644 index 000000000000..147c99191dc2 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-common.dtsi @@ -0,0 +1,405 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include "pxa3xx.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + /* Will be overridden by bootloader */ + hw-revision = <0>; + + chosen { + bootargs = "root=ubi0:RootFS rootfstype=ubifs rw ubi.mtd=3"; + stdout-path = &ffuart; + }; + + memory { + device_type = "memory"; + reg = <0xa0000000 0x8000000>; /* 128 MB */ + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3-fixed-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8-fixed-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_va_5v0: regulator-va-5v0 { + compatible = "regulator-fixed"; + regulator-name = "va-5v0-fixed-supply"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 124 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + ssp_dai0: ssp-dai0 { + compatible = "mrvl,pxa-ssp-dai"; + pinctrl-names = "default"; + pinctrl-0 = <&ssp0_dai_pins>; + port = <&ssp1>; + #sound-dai-cells = <0>; + dmas = <&pdma 13 3 + &pdma 14 3>; + dma-names = "rx", "tx"; + clock-names = "extclk"; + }; + + ssp_dai1: ssp-dai1 { + compatible = "mrvl,pxa-ssp-dai"; + pinctrl-names = "default"; + pinctrl-0 = <&ssp1_dai_pins>; + port = <&ssp2>; + #sound-dai-cells = <0>; + dmas = <&pdma 15 3 + &pdma 16 3>; + dma-names = "rx", "tx"; + clock-names = "extclk"; + }; + + spi: spi { + compatible = "spi-gpio"; + #address-cells = <0x1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&spi_pins>; + gpio-sck = <&gpio 95 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio 98 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpio 97 GPIO_ACTIVE_HIGH>; + cs-gpios = < + &gpio 34 GPIO_ACTIVE_HIGH + &gpio 125 GPIO_ACTIVE_HIGH + &gpio 96 GPIO_ACTIVE_HIGH + >; + num-chipselects = <3>; + + dac: dac@2 { + compatible = "ti,dac7512"; + reg = <2>; + spi-max-frequency = <1000000>; + vcc-supply = <®_3v3>; + }; + }; + + keys: gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_pins>; + + on-off { + label = "on_off button"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,code = <KEY_F6>; + }; + + rescue-boot { + label = "rescue boot button"; + gpios = <&gpio 115 GPIO_ACTIVE_HIGH>; + linux,code = <KEY_F4>; + }; + + setup { + label = "setup"; + gpios = <&gpio 119 GPIO_ACTIVE_HIGH>; + linux,code = <KEY_F3>; + }; + }; + + rotary: rotary-encoder { + compatible = "rotary-encoder"; + gpios = < + &gpio 19 GPIO_ACTIVE_LOW + &gpio 20 GPIO_ACTIVE_HIGH + >; + linux,axis = <REL_X>; + rotary-encoder,relative-axis; + }; + + leds: leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_a &led_pins_b>; + + left { + label = "raumfeld:1"; + gpios = <&gpio 36 GPIO_ACTIVE_LOW>; + }; + + right { + label = "raumfeld:2"; + gpios = <&gpio 35 GPIO_ACTIVE_HIGH>; + }; + }; + + poweroff { + compatible = "gpio-poweroff"; + pinctrl-names = "default"; + pinctrl-0 = <&poweroff_pins>; + gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; + }; + + mmc0_pwrseq: mmc-pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pwrseq_pins>; + reset-gpios = < + &gpio 113 GPIO_ACTIVE_LOW /* W2W_RESET */ + &gpio 114 GPIO_ACTIVE_LOW /* W2W_PDN */ + >; + }; + + ethernet: ethernet@10000000 { + compatible = "smsc,lan9115"; + pinctrl-names = "default"; + pinctrl-0 = <&smsc_pins &smsc_bus_pins>; + reg = <0x10000000 0x100000>; + phy-mode = "mii"; + interrupt-parent = <&gpio>; + interrupts = <40 IRQ_TYPE_EDGE_FALLING>; + vdd33a-supply = <®_3v3>; + vddvario-supply = <®_1v8>; + reset-gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + reg-io-width = <4>; + smsc,save-mac-address; + smsc,irq-push-pull; + }; +}; + +&ffuart { + status = "okay"; +}; + +&pwri2c { + status = "okay"; + + max8660: regulator@34 { + compatible = "maxim,max8660"; + reg = <0x34>; + + regulators { + regulator-v3 { + regulator-compatible = "V3(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator-v4 { + regulator-compatible = "V4(DCDC)"; + regulator-min-microvolt = <725000>; + regulator-max-microvolt = <1800000>; + }; + + regulator-v5 { + regulator-compatible = "V5(LDO)"; + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <2000000>; + }; + + reg_vcc_sdio: regulator-v6 { + regulator-compatible = "V6(LDO)"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + regulator-v7 { + regulator-compatible = "V7(LDO)"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; +}; + +&pxai2c1 { + status = "okay"; + mrvl,i2c-fast-mode; + pinctrl-names = "default"; + pinctrl-0 = <&pxai2c1_pins>; +}; + +&ssp1 { + status = "okay"; +}; + +&ssp2 { + status = "okay"; +}; + +&nand_controller { + status = "okay"; + + nand@0 { + reg = <0>; + nand-rb = <0>; + nand-ecc-mode = "hw"; + marvell,nand-keep-config; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Bootloader"; + reg = <0x0000000 0xa0000>; + read-only; + }; + + partition@a0000 { + label = "BootloaderEnvironment"; + reg = <0x0a0000 0x20000>; + }; + + partition@c0000 { + label = "BootloaderSplashScreen"; + reg = <0x0c0000 0x60000>; + }; + + partition@120000 { + label = "UBI"; + reg = <0x120000 0x7ee0000>; + }; + }; + }; +}; + +&usb0 { + status = "okay"; + marvell,enable-port1; + marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */ + pinctrl-names = "default"; + pinctrl-0 = <&pxa3xx_ohci_pins>; +}; + +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + pxa-mmc,detect-delay-ms = <200>; + vmmc-supply = <®_vcc_sdio>; + mmc-pwrseq = <&mmc0_pwrseq>; + non-removable; + bus-width = <4>; +}; + +&pinctrl { + poweroff_pins: poweroff-pins { + pinctrl-single,pins = <MFP_PIN_PXA300(16) MFP_AF0>; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + led_pins_a: led-pins-a { + pinctrl-single,pins = <MFP_PIN_PXA300(35) MFP_AF0>; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + led_pins_b: led-pins-b { + pinctrl-single,pins = <MFP_PIN_PXA300(36) MFP_AF0>; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_DRIVE_HIGH); + }; + + pxai2c1_pins: pxai2c1-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(21) MFP_AF1 /* I2C_SCL */ + MFP_PIN_PXA300(22) MFP_AF1 /* I2C_SDA */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH); + }; + + gpio_keys_pins: gpio-keys-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(14) MFP_AF0 /* on-off */ + MFP_PIN_PXA300(115) MFP_AF0 /* rescue boot */ + MFP_PIN_PXA300(119) MFP_AF0 /* setup */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + spi_pins: spi-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(95) MFP_AF0 /* SCK */ + MFP_PIN_PXA300(97) MFP_AF0 /* MOSI */ + MFP_PIN_PXA300(98) MFP_AF0 /* MISO */ + MFP_PIN_PXA300(34) MFP_AF0 /* CS#0 */ + MFP_PIN_PXA300(125) MFP_AF0 /* CS#1 */ + MFP_PIN_PXA300(96) MFP_AF0 /* CS#2 */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + pxa3xx_ohci_pins: pxa3xx-ohci-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300_2(0) MFP_AF1 /* USBHPEN */ + MFP_PIN_PXA300_2(1) MFP_AF1 /* USBHPWR */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + smsc_pins: smsc-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(39) MFP_AF0 /* RESET */ + MFP_PIN_PXA300(40) MFP_AF0 /* IRQ */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + smsc_bus_pins: smsc-bus-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(1) MFP_AF1 /* nCS2 */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + mmc0_pins: mmc0-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(3) MFP_AF4 /* MMC1_DAT0 */ + MFP_PIN_PXA300(4) MFP_AF4 /* MMC1_DAT1 */ + MFP_PIN_PXA300(5) MFP_AF4 /* MMC1_DAT2 */ + MFP_PIN_PXA300(6) MFP_AF4 /* MMC1_DAT3 */ + MFP_PIN_PXA300(7) MFP_AF4 /* MMC1_CLK */ + MFP_PIN_PXA300(8) MFP_AF4 /* MMC1_CMD */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_DRIVE_HIGH); + }; + + mmc0_pwrseq_pins: mmc0-pwrseq-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(113) MFP_AF0 /* W2W_RESET */ + MFP_PIN_PXA300(114) MFP_AF0 /* W2W_PDN */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + ssp0_dai_pins: ssp0-dai-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(85) MFP_AF1 /* SSP1_SCLK */ + MFP_PIN_PXA300(86) MFP_AF1 /* SSP1_FRM */ + MFP_PIN_PXA300(87) MFP_AF1 /* SSP1_TXD */ + MFP_PIN_PXA300(88) MFP_AF1 /* SSP1_RXD */ + MFP_PIN_PXA300(89) MFP_AF1 /* SSP1_EXTCLK */ + MFP_PIN_PXA300(90) MFP_AF1 /* SSP1_SYSCLK */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + ssp1_dai_pins: ssp1-dai-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(25) MFP_AF2 /* SSP2_SCLK */ + MFP_PIN_PXA300(26) MFP_AF2 /* SSP2_FRM */ + MFP_PIN_PXA300(27) MFP_AF2 /* SSP2_TXD */ + MFP_PIN_PXA300(29) MFP_AF2 /* SSP2_EXTCLK */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts new file mode 100644 index 000000000000..3e9445419e39 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-connector.dts @@ -0,0 +1,73 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" +#include "pxa300-raumfeld-tuneable-clock.dtsi" + +/ { + model = "Raumfeld Connector (PXA3xx)"; + compatible = "raumfeld,raumfeld-connector-pxa303", "marvell,pxa300"; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "Raumfeld Connector"; + #address-cells = <1>; + #size-cells = <0>; + + simple-audio-card,dai-link@0 { + reg = <0>; + format = "i2s"; + bitclock-master = <&dailink_master_analog>; + frame-master = <&dailink_master_analog>; + mclk-fs = <256>; + + dailink_master_analog: cpu { + sound-dai = <&ssp_dai0>; + }; + + codec { + sound-dai = <&cs4270>; + }; + }; + + simple-audio-card,dai-link@1 { + reg = <1>; + format = "i2s"; + bitclock-master = <&dailink_master_digital>; + frame-master = <&dailink_master_digital>; + mclk-fs = <256>; + + dailink_master_digital: cpu { + sound-dai = <&ssp_dai1>; + }; + + codec { + sound-dai = <&ak4104>; + }; + }; + }; +}; + +&ssp1 { + status = "okay"; +}; + +&ssp2 { + status = "okay"; +}; + +&spi { + ak4104: optical-transmitter@0 { + compatible = "asahi-kasei,ak4104"; + reg = <0>; + vdd-supply = <®_3v3>; + spi-max-frequency = <5000000>; + reset-gpios = <&gpio 38 GPIO_ACTIVE_HIGH>; + #sound-dai-cells = <0>; + }; +}; + +&rotary { + status = "disabled"; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts new file mode 100644 index 000000000000..12b15945ac6d --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-controller.dts @@ -0,0 +1,285 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" + +/ { + model = "Raumfeld Controller (PXA3xx)"; + compatible = "raumfeld,raumfeld-controller-pxa303", "marvell,pxa300"; + + reg_vbatt: regulator-vbatt { + compatible = "regulator-fixed"; + regulator-name = "vbatt-fixed-supply"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-always-on; + }; + + lcd_supply: regulator-va-tft { + compatible = "regulator-fixed"; + regulator-name = "va-tft-fixed-supply"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + onewire { + compatible = "w1-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&w1_pins>; + gpios = < + &gpio 126 GPIO_OPEN_DRAIN /* W1 I/O */ + &gpio 105 GPIO_ACTIVE_HIGH /* pullup */ + >; + + w1_ds2760: slave-ds2760 { + compatible = "maxim,ds2760"; + power-supplies = <&charger>; + }; + }; + + charger: charger { + pinctrl-names = "default"; + pinctrl-0 = <&charger_pins>; + compatible = "gpio-charger"; + charger-type = "mains"; + gpios = <&gpio 101 GPIO_ACTIVE_LOW>; + }; + + /* + * One of the following two will be set to "okay" by the bootloader, + * depending on the hardware revision. + */ + backlight-controller-pwm { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins>; + pwms = <&pwm0 10000>; + power-supply = <®_vbatt>; + status = "disabled"; + + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <100>; + }; + + backlight-controller { + compatible = "lltc,lt3593"; + pinctrl-names = "default"; + pinctrl-0 = <<3593_pins>; + lltc,ctrl-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + status = "disabled"; + + led { + label = "backlight"; + default-state = "on"; + }; + }; +}; + +®_va_5v0 { + status = "disabled"; +}; + +ðernet { + status = "disabled"; +}; + +&leds { + status = "disabled"; +}; + +&dac { + status = "disabled"; +}; + +&pwm0 { + status = "okay"; +}; + +&keys { + pinctrl-0 = <&gpio_keys_pins &dock_detect_pins>; + dock-detect { + label = "dock detect"; + gpios = <&gpio 116 GPIO_ACTIVE_LOW>; + linux,code = <KEY_F5>; + }; +}; + +&spi { + accelerometer@1 { + compatible = "st,lis302dl-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&lis302_pins>; + reg = <1>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <104 IRQ_TYPE_EDGE_FALLING>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + }; +}; + +&lcdc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&lcdc_pins>; + lcd-supply = <&lcd_supply>; + + port { + lcdc_out: endpoint { + remote-endpoint = <&panel_in>; + bus-width = <16>; + }; + }; + + panel { + compatible = "sharp,lq043t3dx0-panel"; + display-timings { + native-mode = <&timing0>; + timing0: timing { + clock-frequency = <9009000>; + pixelclk-active = <0>; /* negative edge */ + hactive = <480>; + vactive = <272>; + hsync-len = <41>; + hback-porch = <2>; + hfront-porch = <1>; + vsync-len = <10>; + vback-porch = <3>; + vfront-porch = <1>; + }; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lcdc_out>; + }; + }; + }; +}; + +&gcu { + status = "okay"; +}; + +&pxai2c1 { + touchscreen@a { + compatible = "eeti,exc3000-i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&eeti_ts_pins>; + reg = <0xa>; + interrupt-parent = <&gpio>; + interrupts = <32 IRQ_TYPE_EDGE_RISING>; + attn-gpios = <&gpio 32 GPIO_ACTIVE_HIGH>; + touchscreen-inverted-y; + }; +}; + +&pinctrl { + lis302_pins: lis302-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(104) MFP_AF0 /* IRQ */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + eeti_ts_pins: eeti-ts-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(32) MFP_AF0 /* IRQ */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + lt3593_pins: lt3593-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(17) MFP_AF0 /* Backlight */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + pwm0_pins: pwm0-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(17) MFP_AF1 /* PWM */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + w1_pins: w1-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(126) MFP_AF0 /* PWM */ + MFP_PIN_PXA300(105) MFP_AF0 /* PWM */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + charger_pins: charger_pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(31) MFP_AF0 /* PEN2 */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH); + pinctrl-single,bias-pullup = MPF_PULL_UP; + }; + + dock_detect_pins: dock_detect_pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(116) MFP_AF0 /* DOCK_DETECT */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH); + pinctrl-single,bias-pullup = MPF_PULL_UP; + }; + + lcdc_pins: lcdc-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(54) MFP_AF1 /* LDD_0 */ + MFP_PIN_PXA300(55) MFP_AF1 /* LDD_1 */ + MFP_PIN_PXA300(56) MFP_AF1 /* LDD_2 */ + MFP_PIN_PXA300(57) MFP_AF1 /* LDD_3 */ + MFP_PIN_PXA300(58) MFP_AF1 /* LDD_4 */ + MFP_PIN_PXA300(59) MFP_AF1 /* LDD_5 */ + MFP_PIN_PXA300(60) MFP_AF1 /* LDD_6 */ + MFP_PIN_PXA300(61) MFP_AF1 /* LDD_7 */ + MFP_PIN_PXA300(62) MFP_AF1 /* LDD_8 */ + MFP_PIN_PXA300(63) MFP_AF1 /* LDD_9 */ + MFP_PIN_PXA300(64) MFP_AF1 /* LDD_10 */ + MFP_PIN_PXA300(65) MFP_AF1 /* LDD_11 */ + MFP_PIN_PXA300(66) MFP_AF1 /* LDD_12 */ + MFP_PIN_PXA300(67) MFP_AF1 /* LDD_13 */ + MFP_PIN_PXA300(68) MFP_AF1 /* LDD_14 */ + MFP_PIN_PXA300(69) MFP_AF1 /* LDD_15 */ + MFP_PIN_PXA300(70) MFP_AF1 /* LDD_16 */ + MFP_PIN_PXA300(71) MFP_AF1 /* LDD_17 */ + MFP_PIN_PXA300(72) MFP_AF1 /* LCD_FCLK */ + MFP_PIN_PXA300(73) MFP_AF1 /* LCD_LCLK */ + MFP_PIN_PXA300(74) MFP_AF1 /* LCD_PCLK */ + MFP_PIN_PXA300(75) MFP_AF1 /* LCD_BIAS */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts new file mode 100644 index 000000000000..5a0f7f17856f --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-l.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" +#include "pxa300-raumfeld-tuneable-clock.dtsi" + +/ { + model = "Raumfeld Speaker L (PXA3xx)"; + compatible = "raumfeld,raumfeld-speaker-l-pxa303", "marvell,pxa300"; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts new file mode 100644 index 000000000000..fa10d896282c --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-m.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" +#include "pxa300-raumfeld-tuneable-clock.dtsi" + +/ { + model = "Raumfeld Speaker M (PXA3xx)"; + compatible = "raumfeld,raumfeld-speaker-m-pxa303", "marvell,pxa300"; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts new file mode 100644 index 000000000000..a70560a8ea92 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-one.dts @@ -0,0 +1,140 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" + +/ { + model = "Raumfeld Speaker One (PXA3xx)"; + compatible = "raumfeld,raumfeld-speaker-one-pxa303", "marvell,pxa300"; + + wm8782: wm8782 { + compatible = "wm8782"; + #sound-dai-cells = <0>; + Vdd-supply = <®_3v3>; + Vdda-supply = <®_va_5v0>; + }; + + xo_11mhz: oscillator-11mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <11289600>; + clock-accuracy = <100>; + }; + + xo_audio: clock-gate { + compatible = "gpio-gate-clock"; + pinctrlnames = "default"; + pinctrl-0 = <&xo_audio_pins>; + clocks = <&xo_11mhz>; + #clock-cells = <0>; + enable-gpios = <&gpio 111 GPIO_ACTIVE_HIGH>; + }; + + reg_va_30v0: regulator-va-30v0 { + compatible = "regulator-fixed"; + regulator-name = "va-30v0-fixed-supply"; + regulator-min-microvolt = <30000000>; + regulator-max-microvolt = <30000000>; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "Raumfeld Speaker"; + #address-cells = <1>; + #size-cells = <0>; + + simple-audio-card,dai-link@0 { + reg = <0>; + format = "i2s"; + bitclock-master = <&dailink_master_analog_out>; + frame-master = <&dailink_master_analog_out>; + mclk-fs = <256>; + + dailink_master_analog_out: cpu { + sound-dai = <&ssp_dai0>; + }; + + codec { + sound-dai = <&sta320>; + }; + }; + + simple-audio-card,dai-link@1 { + reg = <1>; + format = "i2s"; + bitclock-master = <&dailink_master_analog_in>; + frame-master = <&dailink_master_analog_in>; + mclk-fs = <256>; + + dailink_master_analog_in: cpu { + sound-dai = <&ssp_dai0>; + }; + + codec { + sound-dai = <&wm8782>; + }; + }; + }; +}; + +&ssp_dai0 { + clocks = <&xo_audio>; +}; + +&spi { + dac@2 { + compatible = "ti,dac7512"; + reg = <2>; + spi-max-frequency = <1000000>; + vcc-supply = <®_3v3>; + }; +}; + +&rotary { + status = "okay"; +}; + +&pxai2c1 { + sta320: codec@1a { + compatible = "st,sta32x"; + reg = <0x1a>; + pinctrl-names = "default"; + pinctrl-0 = <&sta320_pins>; + clocks = <&xo_audio>; + clock-names = "xti"; + reset-gpios = <&gpio 120 GPIO_ACTIVE_HIGH>; + Vdda-supply = <®_3v3>; + Vdd3-supply = <®_3v3>; + Vcc-supply = <®_va_30v0>; + #sound-dai-cells = <0>; + st,thermal-warning-adjustment; + st,thermal-warning-recovery; + st,fault-detect-recovery; + st,drop-compensation-ns = <80>; + st,max-power-use-mpcc; + st,invalid-input-detect-mute; + /* 2 (half-bridge) and 1 (full-bridge) on-board power */ + st,output-conf = /bits/ 8 <0x1>; + st,ch1-output-mapping = /bits/ 8 <0>; + st,ch2-output-mapping = /bits/ 8 <1>; + st,ch3-output-mapping = /bits/ 8 <2>; + st,needs_esd_watchdog; + }; +}; + +&pinctrl { + xo_audio_pins: xo-audio-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(111) MFP_AF0 /* ENABLE */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + sta320_pins: sta320-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(120) MFP_AF0 /* CODEC_RESET */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts new file mode 100644 index 000000000000..36e20cbf8704 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-speaker-s.dts @@ -0,0 +1,11 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" +#include "pxa300-raumfeld-tuneable-clock.dtsi" + +/ { + model = "Raumfeld Speaker S (PXA3xx)"; + compatible = "raumfeld,raumfeld-speaker-s-pxa303", "marvell,pxa300"; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi new file mode 100644 index 000000000000..561483b93989 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa300-raumfeld-tuneable-clock.dtsi @@ -0,0 +1,85 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include <dt-bindings/clock/maxim,max9485.h> + +/ { + xo_27mhz: oscillator-27mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + clock-accuracy = <100>; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "Raumfeld Speaker"; + #address-cells = <1>; + #size-cells = <0>; + + simple-audio-card,dai-link@0 { + reg = <0>; + format = "i2s"; + bitclock-master = <&dailink_master_analog>; + frame-master = <&dailink_master_analog>; + mclk-fs = <256>; + + dailink_master_analog: cpu { + sound-dai = <&ssp_dai0>; + }; + + codec { + sound-dai = <&cs4270>; + }; + }; + }; +}; + +&ssp_dai0 { + clocks = <&max9485 MAX9485_CLKOUT1>; +}; + +&ssp_dai1 { + clocks = <&max9485 MAX9485_CLKOUT1>; +}; + +&pxai2c1 { + cs4270: codec@48 { + compatible = "cirrus,cs4270"; + pinctrl-names = "default"; + pinctrl-0 = <&cs4270_pins>; + reg = <0x48>; + va-supply = <®_va_5v0>; + vd-supply = <®_3v3>; + vlc-supply = <®_3v3>; + reset-gpios = <&gpio 120 GPIO_ACTIVE_HIGH>; + #sound-dai-cells = <0>; + }; + + max9485: clock-generator@63 { + compatible = "maxim,max9485"; + pinctrl-names = "default"; + pinctrl-0 = <&max9485_pins>; + reg = <0x63>; + vdd-supply = <®_3v3>; + clock-names = "xclk"; + clocks = <&xo_27mhz>; + reset-gpios = <&gpio 111 GPIO_ACTIVE_HIGH>; + #clock-cells = <1>; + }; +}; + +&pinctrl { + cs4270_pins: cs4270-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(120) MFP_AF0 /* RESET */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + max9485_pins: max9485-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(111) MFP_AF0 /* RESET */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; +}; diff --git a/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi b/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi new file mode 100644 index 000000000000..f9c216f91865 --- /dev/null +++ b/arch/arm/boot/dts/intel/pxa/pxa3xx.dtsi @@ -0,0 +1,320 @@ +// SPDX-License-Identifier: GPL-2.0 +/* The pxa3xx skeleton simply augments the 2xx version */ +#include "pxa2xx.dtsi" + +#define MFP_PIN_PXA300(gpio) \ + ((gpio <= 2) ? (0x00b4 + 4 * gpio) : \ + (gpio <= 26) ? (0x027c + 4 * (gpio - 3)) : \ + (gpio <= 98) ? (0x0400 + 4 * (gpio - 27)) : \ + (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \ + 0) +#define MFP_PIN_PXA300_2(gpio) \ + ((gpio <= 1) ? (0x674 + 4 * gpio) : \ + (gpio <= 6) ? (0x2dc + 4 * gpio) : \ + 0) + +#define MFP_PIN_PXA310(gpio) \ + ((gpio <= 2) ? (0x00b4 + 4 * gpio) : \ + (gpio <= 26) ? (0x027c + 4 * (gpio - 3)) : \ + (gpio <= 29) ? (0x0400 + 4 * (gpio - 27)) : \ + (gpio <= 98) ? (0x0418 + 4 * (gpio - 30)) : \ + (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \ + (gpio <= 262) ? 0 : \ + (gpio <= 268) ? (0x052c + 4 * (gpio - 263)) : \ + 0) +#define MFP_PIN_PXA310_2(gpio) \ + ((gpio <= 1) ? (0x674 + 4 * gpio) : \ + (gpio <= 6) ? (0x2dc + 4 * gpio) : \ + (gpio <= 10) ? (0x52c + 4 * gpio) : \ + 0) + +#define MFP_PIN_PXA320(gpio) \ + ((gpio <= 4) ? (0x0124 + 4 * gpio) : \ + (gpio <= 9) ? (0x028c + 4 * (gpio - 5)) : \ + (gpio <= 10) ? (0x0458 + 4 * (gpio - 10)) : \ + (gpio <= 26) ? (0x02a0 + 4 * (gpio - 11)) : \ + (gpio <= 48) ? (0x0400 + 4 * (gpio - 27)) : \ + (gpio <= 62) ? (0x045c + 4 * (gpio - 49)) : \ + (gpio <= 73) ? (0x04b4 + 4 * (gpio - 63)) : \ + (gpio <= 98) ? (0x04f0 + 4 * (gpio - 74)) : \ + (gpio <= 127) ? (0x0600 + 4 * (gpio - 99)) : \ + 0) +#define MFP_PIN_PXA320_2(gpio) \ + ((gpio <= 3) ? (0x674 + 4 * gpio) : \ + (gpio <= 5) ? (0x284 + 4 * gpio) : \ + 0) + +/* + * MFP Alternate functions for pins having a gpio. + * Example of use: pinctrl-single,pins = < MFP_PIN_PXA310(21) MFP_AF1 > + */ +#define MFP_AF0 (0 << 0) +#define MFP_AF1 (1 << 0) +#define MFP_AF2 (2 << 0) +#define MFP_AF3 (3 << 0) +#define MFP_AF4 (4 << 0) +#define MFP_AF5 (5 << 0) +#define MFP_AF6 (6 << 0) + +/* + * MFP drive strength functions for pins. + * Example of use: pinctrl-single,drive-strength = MFP_DS03X; + */ +#define MFP_DSMSK (0x7 << 10) +#define MFP_DS01X < (0x0 << 10) MFP_DSMSK > +#define MFP_DS02X < (0x1 << 10) MFP_DSMSK > +#define MFP_DS03X < (0x2 << 10) MFP_DSMSK > +#define MFP_DS04X < (0x3 << 10) MFP_DSMSK > +#define MFP_DS06X < (0x4 << 10) MFP_DSMSK > +#define MFP_DS08X < (0x5 << 10) MFP_DSMSK > +#define MFP_DS10X < (0x6 << 10) MFP_DSMSK > +#define MFP_DS13X < (0x7 << 10) MFP_DSMSK > + +/* + * MFP bias pull mode for pins. + * Example of use: pinctrl-single,bias-pullup = MPF_PULL_UP; + */ +#define MPF_PULL_MSK (0x7 << 13) +#define MPF_PULL_DOWN < (0x5 << 13) (0x5 << 13) 0 MPF_PULL_MSK > +#define MPF_PULL_UP < (0x6 << 13) (0x6 << 13) 0 MPF_PULL_MSK > + +/* + * MFP low power mode for pins. + * Example of use: + * pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW|MFP_LPM_EDGE_FALL); + * + * Table that determines the low power modes outputs, with actual settings + * used in parentheses for don't-care values. Except for the float output, + * the configured driven and pulled levels match, so if there is a need for + * non-LPM pulled output, the same configuration could probably be used. + * + * Output value sleep_oe_n sleep_data pullup_en pulldown_en pull_sel + * (bit 7) (bit 8) (bit 14) (bit 13) (bit 15) + * + * Input 0 X(0) X(0) X(0) 0 + * Drive 0 0 0 0 X(1) 0 + * Drive 1 0 1 X(1) 0 0 + * Pull hi (1) 1 X(1) 1 0 0 + * Pull lo (0) 1 X(0) 0 1 0 + * Z (float) 1 X(0) 0 0 0 + */ +#define MFP_LPM(x) < (x) MFP_LPM_MSK > + +#define MFP_LPM_MSK 0xe1f0 +#define MFP_LPM_INPUT 0x0000 +#define MFP_LPM_DRIVE_LOW 0x2000 +#define MFP_LPM_DRIVE_HIGH 0x4100 +#define MFP_LPM_PULL_LOW 0x2080 +#define MFP_LPM_PULL_HIGH 0x4180 +#define MFP_LPM_FLOAT 0x0080 + +#define MFP_LPM_EDGE_NONE 0x0000 +#define MFP_LPM_EDGE_RISE 0x0010 +#define MFP_LPM_EDGE_FALL 0x0020 +#define MFP_LPM_EDGE_BOTH 0x0030 + +/ { + model = "Marvell PXA3xx familiy SoC"; + compatible = "marvell,pxa3xx"; + + pxabus { + pdma: dma-controller@40000000 { + compatible = "marvell,pdma-1.0"; + reg = <0x40000000 0x10000>; + interrupts = <25>; + #dma-cells = <2>; + /* For backwards compatibility: */ + #dma-channels = <32>; + dma-channels = <32>; + #dma-requests = <100>; + dma-requests = <100>; + status = "okay"; + }; + + pwri2c: i2c@40f500c0 { + compatible = "mrvl,pwri2c"; + reg = <0x40f500c0 0x30>; + interrupts = <6>; + clocks = <&clks CLK_PWRI2C>; + #address-cells = <0x1>; + #size-cells = <0>; + status = "disabled"; + }; + + nand_controller: nand-controller@43100000 { + compatible = "marvell,pxa3xx-nand-controller"; + reg = <0x43100000 90>; + interrupts = <45>; + clocks = <&clks CLK_NAND>; + clock-names = "core"; + dmas = <&pdma 97 3>; + dma-names = "data"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + pxairq: interrupt-controller@40d00000 { + marvell,intc-priority; + marvell,intc-nr-irqs = <56>; + }; + + pinctrl: pinctrl@40e10000 { + compatible = "pinconf-single"; + reg = <0x40e10000 0xffff>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <32>; + pinctrl-single,function-mask = <0x7>; + }; + + gpio: gpio@40e00000 { + compatible = "intel,pxa3xx-gpio"; + reg = <0x40e00000 0x10000>; + clocks = <&clks CLK_GPIO>; + gpio-ranges = <&pinctrl 0 0 128>; + interrupt-names = "gpio0", "gpio1", "gpio_mux"; + interrupts = <8>, <9>, <10>; + gpio-controller; + #gpio-cells = <0x2>; + interrupt-controller; + #interrupt-cells = <0x2>; + }; + + mmc0: mmc@41100000 { + compatible = "marvell,pxa-mmc"; + reg = <0x41100000 0x1000>; + interrupts = <23>; + clocks = <&clks CLK_MMC1>; + dmas = <&pdma 21 3 + &pdma 22 3>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + mmc1: mmc@42000000 { + compatible = "marvell,pxa-mmc"; + reg = <0x42000000 0x1000>; + interrupts = <41>; + clocks = <&clks CLK_MMC2>; + dmas = <&pdma 93 3 + &pdma 94 3>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + mmc2: mmc@42500000 { + compatible = "marvell,pxa-mmc"; + reg = <0x42500000 0x1000>; + interrupts = <55>; + clocks = <&clks CLK_MMC3>; + dmas = <&pdma 46 3 + &pdma 47 3>; + dma-names = "rx", "tx"; + status = "disabled"; + }; + + usb0: usb@4c000000 { + compatible = "marvell,pxa-ohci"; + reg = <0x4c000000 0x10000>; + interrupts = <3>; + clocks = <&clks CLK_USBH>; + status = "disabled"; + }; + + pwm0: pwm@40b00000 { + compatible = "marvell,pxa270-pwm"; + reg = <0x40b00000 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM0>; + status = "disabled"; + }; + + pwm1: pwm@40b00010 { + compatible = "marvell,pxa270-pwm"; + reg = <0x40b00010 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM1>; + status = "disabled"; + }; + + pwm2: pwm@40c00000 { + compatible = "marvell,pxa270-pwm"; + reg = <0x40c00000 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM0>; + status = "disabled"; + }; + + pwm3: pwm@40c00010 { + compatible = "marvell,pxa270-pwm"; + reg = <0x40c00010 0x10>; + #pwm-cells = <1>; + clocks = <&clks CLK_PWM1>; + status = "disabled"; + }; + + ssp1: ssp@41000000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41000000 0x40>; + interrupts = <24>; + clocks = <&clks CLK_SSP1>; + status = "disabled"; + }; + + ssp2: ssp@41700000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41700000 0x40>; + interrupts = <16>; + clocks = <&clks CLK_SSP2>; + status = "disabled"; + }; + + ssp3: ssp@41900000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41900000 0x40>; + interrupts = <0>; + clocks = <&clks CLK_SSP3>; + status = "disabled"; + }; + + ssp4: ssp@41a00000 { + compatible = "mrvl,pxa3xx-ssp"; + reg = <0x41a00000 0x40>; + interrupts = <13>; + clocks = <&clks CLK_SSP4>; + status = "disabled"; + }; + + timer@40a00000 { + compatible = "marvell,pxa-timer"; + reg = <0x40a00000 0x20>; + interrupts = <26>; + clocks = <&clks CLK_OSTIMER>; + status = "okay"; + }; + + gcu: display-controller@54000000 { + compatible = "marvell,pxa300-gcu"; + reg = <0x54000000 0x1000>; + interrupts = <39>; + clocks = <&clks CLK_PXA300_GCU>; + status = "disabled"; + }; + }; + + clocks { + /* + * The muxing of external clocks/internal dividers for osc* clock + * sources has been hidden under the carpet by now. + */ + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clks: clocks { + compatible = "marvell,pxa300-clocks"; + #clock-cells = <1>; + status = "okay"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/Makefile b/arch/arm/boot/dts/intel/socfpga/Makefile new file mode 100644 index 000000000000..c467828aeb4b --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/Makefile @@ -0,0 +1,17 @@ +# SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \ + socfpga_arria5_socdk.dtb \ + socfpga_arria10_chameleonv3.dtb \ + socfpga_arria10_mercury_pe1.dtb \ + socfpga_arria10_socdk_nand.dtb \ + socfpga_arria10_socdk_qspi.dtb \ + socfpga_arria10_socdk_sdmmc.dtb \ + socfpga_cyclone5_chameleon96.dtb \ + socfpga_cyclone5_mcvevk.dtb \ + socfpga_cyclone5_socdk.dtb \ + socfpga_cyclone5_de0_nano_soc.dtb \ + socfpga_cyclone5_sockit.dtb \ + socfpga_cyclone5_socrates.dtb \ + socfpga_cyclone5_sodia.dtb \ + socfpga_cyclone5_vining_fpga.dtb \ + socfpga_vt.dtb diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi new file mode 100644 index 000000000000..4c1d140f40f8 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga.dtsi @@ -0,0 +1,984 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2012 Altera <www.altera.com> + */ + +#include <dt-bindings/reset/altr,rst-mgr.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + aliases { + serial0 = &uart0; + serial1 = &uart1; + timer0 = &timer0; + timer1 = &timer1; + timer2 = &timer2; + timer3 = &timer3; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "altr,socfpga-smp"; + + cpu0: cpu@0 { + compatible = "arm,cortex-a9"; + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2>; + }; + cpu1: cpu@1 { + compatible = "arm,cortex-a9"; + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2>; + }; + }; + + pmu: pmu@ff111000 { + compatible = "arm,cortex-a9-pmu"; + interrupt-parent = <&intc>; + interrupts = <0 176 4>, <0 177 4>; + interrupt-affinity = <&cpu0>, <&cpu1>; + reg = <0xff111000 0x1000>, + <0xff113000 0x1000>; + }; + + intc: interrupt-controller@fffed000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0xfffed000 0x1000>, + <0xfffec100 0x100>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + device_type = "soc"; + interrupt-parent = <&intc>; + ranges; + + amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pdma: pdma@ffe01000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0xffe01000 0x1000>; + interrupts = <0 104 4>, + <0 105 4>, + <0 106 4>, + <0 107 4>, + <0 108 4>, + <0 109 4>, + <0 110 4>, + <0 111 4>; + #dma-cells = <1>; + clocks = <&l4_main_clk>; + clock-names = "apb_pclk"; + resets = <&rst DMA_RESET>; + reset-names = "dma"; + }; + }; + + base_fpga_region { + compatible = "fpga-region"; + fpga-mgr = <&fpgamgr0>; + + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + can0: can@ffc00000 { + compatible = "bosch,d_can"; + reg = <0xffc00000 0x1000>; + interrupts = <0 131 4>, <0 132 4>, <0 133 4>, <0 134 4>; + clocks = <&can0_clk>; + resets = <&rst CAN0_RESET>; + status = "disabled"; + }; + + can1: can@ffc01000 { + compatible = "bosch,d_can"; + reg = <0xffc01000 0x1000>; + interrupts = <0 135 4>, <0 136 4>, <0 137 4>, <0 138 4>; + clocks = <&can1_clk>; + resets = <&rst CAN1_RESET>; + status = "disabled"; + }; + + clkmgr@ffd04000 { + compatible = "altr,clk-mgr"; + reg = <0xffd04000 0x1000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + osc1: osc1 { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + osc2: osc2 { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + f2s_periph_ref_clk: f2s_periph_ref_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + f2s_sdram_ref_clk: f2s_sdram_ref_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + main_pll: main_pll@40 { + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + compatible = "altr,socfpga-pll-clock"; + clocks = <&osc1>; + reg = <0x40>; + + mpuclk: mpuclk@48 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&main_pll>; + div-reg = <0xe0 0 9>; + reg = <0x48>; + }; + + mainclk: mainclk@4c { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&main_pll>; + div-reg = <0xe4 0 9>; + reg = <0x4C>; + }; + + dbg_base_clk: dbg_base_clk@50 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&main_pll>, <&osc1>; + div-reg = <0xe8 0 9>; + reg = <0x50>; + }; + + main_qspi_clk: main_qspi_clk@54 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&main_pll>; + reg = <0x54>; + }; + + main_nand_sdmmc_clk: main_nand_sdmmc_clk@58 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&main_pll>; + reg = <0x58>; + }; + + cfg_h2f_usr0_clk: cfg_h2f_usr0_clk@5c { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&main_pll>; + reg = <0x5C>; + }; + }; + + periph_pll: periph_pll@80 { + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + compatible = "altr,socfpga-pll-clock"; + clocks = <&osc1>, <&osc2>, <&f2s_periph_ref_clk>; + reg = <0x80>; + + emac0_clk: emac0_clk@88 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&periph_pll>; + reg = <0x88>; + }; + + emac1_clk: emac1_clk@8c { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&periph_pll>; + reg = <0x8C>; + }; + + per_qspi_clk: per_qsi_clk@90 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&periph_pll>; + reg = <0x90>; + }; + + per_nand_mmc_clk: per_nand_mmc_clk@94 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&periph_pll>; + reg = <0x94>; + }; + + per_base_clk: per_base_clk@98 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&periph_pll>; + reg = <0x98>; + }; + + h2f_usr1_clk: h2f_usr1_clk@9c { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&periph_pll>; + reg = <0x9C>; + }; + }; + + sdram_pll: sdram_pll@c0 { + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + compatible = "altr,socfpga-pll-clock"; + clocks = <&osc1>, <&osc2>, <&f2s_sdram_ref_clk>; + reg = <0xC0>; + + ddr_dqs_clk: ddr_dqs_clk@c8 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&sdram_pll>; + reg = <0xC8>; + }; + + ddr_2x_dqs_clk: ddr_2x_dqs_clk@cc { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&sdram_pll>; + reg = <0xCC>; + }; + + ddr_dq_clk: ddr_dq_clk@d0 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&sdram_pll>; + reg = <0xD0>; + }; + + h2f_usr2_clk: h2f_usr2_clk@d4 { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&sdram_pll>; + reg = <0xD4>; + }; + }; + + mpu_periph_clk: mpu_periph_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&mpuclk>; + fixed-divider = <4>; + }; + + mpu_l2_ram_clk: mpu_l2_ram_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&mpuclk>; + fixed-divider = <2>; + }; + + l4_main_clk: l4_main_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>; + clk-gate = <0x60 0>; + }; + + l3_main_clk: l3_main_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-perip-clk"; + clocks = <&mainclk>; + fixed-divider = <1>; + }; + + l3_mp_clk: l3_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>; + div-reg = <0x64 0 2>; + clk-gate = <0x60 1>; + }; + + l3_sp_clk: l3_sp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&l3_mp_clk>; + div-reg = <0x64 2 2>; + }; + + l4_mp_clk: l4_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>, <&per_base_clk>; + div-reg = <0x64 4 3>; + clk-gate = <0x60 2>; + }; + + l4_sp_clk: l4_sp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&mainclk>, <&per_base_clk>; + div-reg = <0x64 7 3>; + clk-gate = <0x60 3>; + }; + + dbg_at_clk: dbg_at_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + div-reg = <0x68 0 2>; + clk-gate = <0x60 4>; + }; + + dbg_clk: dbg_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_at_clk>; + div-reg = <0x68 2 2>; + clk-gate = <0x60 5>; + }; + + dbg_trace_clk: dbg_trace_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + div-reg = <0x6C 0 3>; + clk-gate = <0x60 6>; + }; + + dbg_timer_clk: dbg_timer_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&dbg_base_clk>; + clk-gate = <0x60 7>; + }; + + cfg_clk: cfg_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&cfg_h2f_usr0_clk>; + clk-gate = <0x60 8>; + }; + + h2f_user0_clk: h2f_user0_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&cfg_h2f_usr0_clk>; + clk-gate = <0x60 9>; + }; + + emac_0_clk: emac_0_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&emac0_clk>; + clk-gate = <0xa0 0>; + }; + + emac_1_clk: emac_1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&emac1_clk>; + clk-gate = <0xa0 1>; + }; + + usb_mp_clk: usb_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 2>; + div-reg = <0xa4 0 3>; + }; + + spi_m_clk: spi_m_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 3>; + div-reg = <0xa4 3 3>; + }; + + can0_clk: can0_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 4>; + div-reg = <0xa4 6 3>; + }; + + can1_clk: can1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 5>; + div-reg = <0xa4 9 3>; + }; + + gpio_db_clk: gpio_db_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&per_base_clk>; + clk-gate = <0xa0 6>; + div-reg = <0xa8 0 24>; + }; + + h2f_user1_clk: h2f_user1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&h2f_usr1_clk>; + clk-gate = <0xa0 7>; + }; + + sdmmc_clk: sdmmc_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; + clk-gate = <0xa0 8>; + }; + + sdmmc_clk_divided: sdmmc_clk_divided { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&sdmmc_clk>; + clk-gate = <0xa0 8>; + fixed-divider = <4>; + }; + + nand_x_clk: nand_x_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_nand_sdmmc_clk>, <&per_nand_mmc_clk>; + clk-gate = <0xa0 9>; + }; + + nand_ecc_clk: nand_ecc_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&nand_x_clk>; + clk-gate = <0xa0 9>; + }; + + nand_clk: nand_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&nand_x_clk>; + clk-gate = <0xa0 10>; + fixed-divider = <4>; + }; + + qspi_clk: qspi_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&f2s_periph_ref_clk>, <&main_qspi_clk>, <&per_qspi_clk>; + clk-gate = <0xa0 11>; + }; + + ddr_dqs_clk_gate: ddr_dqs_clk_gate { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&ddr_dqs_clk>; + clk-gate = <0xd8 0>; + }; + + ddr_2x_dqs_clk_gate: ddr_2x_dqs_clk_gate { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&ddr_2x_dqs_clk>; + clk-gate = <0xd8 1>; + }; + + ddr_dq_clk_gate: ddr_dq_clk_gate { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&ddr_dq_clk>; + clk-gate = <0xd8 2>; + }; + + h2f_user2_clk: h2f_user2_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-gate-clk"; + clocks = <&h2f_usr2_clk>; + clk-gate = <0xd8 3>; + }; + + }; + }; + + fpga_bridge0: fpga_bridge@ff400000 { + compatible = "altr,socfpga-lwhps2fpga-bridge"; + reg = <0xff400000 0x100000>; + resets = <&rst LWHPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + status = "disabled"; + }; + + fpga_bridge1: fpga_bridge@ff500000 { + compatible = "altr,socfpga-hps2fpga-bridge"; + reg = <0xff500000 0x10000>; + resets = <&rst HPS2FPGA_RESET>; + clocks = <&l4_main_clk>; + status = "disabled"; + }; + + fpga_bridge2: fpga-bridge@ff600000 { + compatible = "altr,socfpga-fpga2hps-bridge"; + reg = <0xff600000 0x100000>; + resets = <&rst FPGA2HPS_RESET>; + clocks = <&l4_main_clk>; + status = "disabled"; + }; + + fpga_bridge3: fpga-bridge@ffc25080 { + compatible = "altr,socfpga-fpga2sdram-bridge"; + reg = <0xffc25080 0x4>; + status = "disabled"; + }; + + fpgamgr0: fpgamgr@ff706000 { + compatible = "altr,socfpga-fpga-mgr"; + reg = <0xff706000 0x1000 + 0xffb90000 0x4>; + interrupts = <0 175 4>; + }; + + socfpga_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <0 0 0 0 16 0 0>; + }; + + gmac0: ethernet@ff700000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 0>; + reg = <0xff700000 0x2000>; + interrupts = <0 115 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac_0_clk>; + clock-names = "stmmaceth"; + resets = <&rst EMAC0_RESET>; + reset-names = "stmmaceth"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + tx-fifo-depth = <4096>; + rx-fifo-depth = <4096>; + snps,axi-config = <&socfpga_axi_setup>; + status = "disabled"; + }; + + gmac1: ethernet@ff702000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 2>; + reg = <0xff702000 0x2000>; + interrupts = <0 120 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac_1_clk>; + clock-names = "stmmaceth"; + resets = <&rst EMAC1_RESET>; + reset-names = "stmmaceth"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + tx-fifo-depth = <4096>; + rx-fifo-depth = <4096>; + snps,axi-config = <&socfpga_axi_setup>; + status = "disabled"; + }; + + gpio0: gpio@ff708000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xff708000 0x1000>; + clocks = <&l4_mp_clk>; + resets = <&rst GPIO0_RESET>; + status = "disabled"; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <29>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 164 4>; + }; + }; + + gpio1: gpio@ff709000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xff709000 0x1000>; + clocks = <&l4_mp_clk>; + resets = <&rst GPIO1_RESET>; + status = "disabled"; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <29>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 165 4>; + }; + }; + + gpio2: gpio@ff70a000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xff70a000 0x1000>; + clocks = <&l4_mp_clk>; + resets = <&rst GPIO2_RESET>; + status = "disabled"; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <27>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 166 4>; + }; + }; + + i2c0: i2c@ffc04000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc04000 0x1000>; + resets = <&rst I2C0_RESET>; + clocks = <&l4_sp_clk>; + interrupts = <0 158 0x4>; + status = "disabled"; + }; + + i2c1: i2c@ffc05000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc05000 0x1000>; + resets = <&rst I2C1_RESET>; + clocks = <&l4_sp_clk>; + interrupts = <0 159 0x4>; + status = "disabled"; + }; + + i2c2: i2c@ffc06000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc06000 0x1000>; + resets = <&rst I2C2_RESET>; + clocks = <&l4_sp_clk>; + interrupts = <0 160 0x4>; + status = "disabled"; + }; + + i2c3: i2c@ffc07000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc07000 0x1000>; + resets = <&rst I2C3_RESET>; + clocks = <&l4_sp_clk>; + interrupts = <0 161 0x4>; + status = "disabled"; + }; + + eccmgr: eccmgr { + compatible = "altr,socfpga-ecc-manager"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + l2-ecc@ffd08140 { + compatible = "altr,socfpga-l2-ecc"; + reg = <0xffd08140 0x4>; + interrupts = <0 36 1>, <0 37 1>; + }; + + ocram-ecc@ffd08144 { + compatible = "altr,socfpga-ocram-ecc"; + reg = <0xffd08144 0x4>; + iram = <&ocram>; + interrupts = <0 178 1>, <0 179 1>; + }; + }; + + L2: cache-controller@fffef000 { + compatible = "arm,pl310-cache"; + reg = <0xfffef000 0x1000>; + interrupts = <0 38 0x04>; + cache-unified; + cache-level = <2>; + arm,tag-latency = <1 1 1>; + arm,data-latency = <2 1 1>; + prefetch-data = <1>; + prefetch-instr = <1>; + arm,shared-override; + arm,double-linefill = <1>; + arm,double-linefill-incr = <0>; + arm,double-linefill-wrap = <1>; + arm,prefetch-drop = <0>; + arm,prefetch-offset = <7>; + }; + + l3regs@ff800000 { + compatible = "altr,l3regs", "syscon"; + reg = <0xff800000 0x1000>; + }; + + mmc: mmc@ff704000 { + compatible = "altr,socfpga-dw-mshc"; + reg = <0xff704000 0x1000>; + interrupts = <0 139 4>; + fifo-depth = <0x400>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&l4_mp_clk>, <&sdmmc_clk_divided>; + clock-names = "biu", "ciu"; + resets = <&rst SDMMC_RESET>; + altr,sysmgr-syscon = <&sysmgr 0x108 3>; + status = "disabled"; + }; + + nand0: nand@ff900000 { + #address-cells = <0x1>; + #size-cells = <0x0>; + compatible = "altr,socfpga-denali-nand"; + reg = <0xff900000 0x100000>, + <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0x0 0x90 0x4>; + clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>; + clock-names = "nand", "nand_x", "ecc"; + resets = <&rst NAND_RESET>; + status = "disabled"; + }; + + ocram: sram@ffff0000 { + compatible = "mmio-sram"; + reg = <0xffff0000 0x10000>; + }; + + qspi: spi@ff705000 { + compatible = "intel,socfpga-qspi", "cdns,qspi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff705000 0x1000>, + <0xffa00000 0x1000>; + interrupts = <0 151 4>; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + clocks = <&qspi_clk>; + resets = <&rst QSPI_RESET>; + status = "disabled"; + }; + + rst: rstmgr@ffd05000 { + #reset-cells = <1>; + compatible = "altr,rst-mgr"; + reg = <0xffd05000 0x1000>; + altr,modrst-offset = <0x10>; + }; + + scu: snoop-control-unit@fffec000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xfffec000 0x100>; + }; + + sdr: sdr@ffc25000 { + compatible = "altr,sdr-ctl", "syscon"; + reg = <0xffc25000 0x1000>; + resets = <&rst SDR_RESET>; + }; + + sdramedac { + compatible = "altr,sdram-edac"; + altr,sdr-syscon = <&sdr>; + interrupts = <0 39 4>; + }; + + spi0: spi@fff00000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfff00000 0x1000>; + interrupts = <0 154 4>; + num-cs = <4>; + clocks = <&spi_m_clk>; + resets = <&rst SPIM0_RESET>; + reset-names = "spi"; + status = "disabled"; + }; + + spi1: spi@fff01000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xfff01000 0x1000>; + interrupts = <0 155 4>; + num-cs = <4>; + clocks = <&spi_m_clk>; + resets = <&rst SPIM1_RESET>; + reset-names = "spi"; + status = "disabled"; + }; + + sysmgr: sysmgr@ffd08000 { + compatible = "altr,sys-mgr", "syscon"; + reg = <0xffd08000 0x4000>; + }; + + /* Local timer */ + timer@fffec600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xfffec600 0x100>; + interrupts = <1 13 0xf01>; + clocks = <&mpu_periph_clk>; + }; + + timer0: timer0@ffc08000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 167 4>; + reg = <0xffc08000 0x1000>; + clocks = <&l4_sp_clk>; + clock-names = "timer"; + resets = <&rst SPTIMER0_RESET>; + reset-names = "timer"; + }; + + timer1: timer1@ffc09000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 168 4>; + reg = <0xffc09000 0x1000>; + clocks = <&l4_sp_clk>; + clock-names = "timer"; + resets = <&rst SPTIMER1_RESET>; + reset-names = "timer"; + }; + + timer2: timer2@ffd00000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 169 4>; + reg = <0xffd00000 0x1000>; + clocks = <&osc1>; + clock-names = "timer"; + resets = <&rst OSC1TIMER0_RESET>; + reset-names = "timer"; + }; + + timer3: timer3@ffd01000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 170 4>; + reg = <0xffd01000 0x1000>; + clocks = <&osc1>; + clock-names = "timer"; + resets = <&rst OSC1TIMER1_RESET>; + reset-names = "timer"; + }; + + uart0: serial@ffc02000 { + compatible = "snps,dw-apb-uart"; + reg = <0xffc02000 0x1000>; + interrupts = <0 162 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&l4_sp_clk>; + dmas = <&pdma 28>, + <&pdma 29>; + dma-names = "tx", "rx"; + resets = <&rst UART0_RESET>; + }; + + uart1: serial@ffc03000 { + compatible = "snps,dw-apb-uart"; + reg = <0xffc03000 0x1000>; + interrupts = <0 163 4>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&l4_sp_clk>; + dmas = <&pdma 30>, + <&pdma 31>; + dma-names = "tx", "rx"; + resets = <&rst UART1_RESET>; + }; + + usbphy0: usbphy { + #phy-cells = <0>; + compatible = "usb-nop-xceiv"; + status = "okay"; + }; + + usb0: usb@ffb00000 { + compatible = "snps,dwc2"; + reg = <0xffb00000 0xffff>; + interrupts = <0 125 4>; + clocks = <&usb_mp_clk>; + clock-names = "otg"; + resets = <&rst USB0_RESET>; + reset-names = "dwc2"; + phys = <&usbphy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + usb1: usb@ffb40000 { + compatible = "snps,dwc2"; + reg = <0xffb40000 0xffff>; + interrupts = <0 128 4>; + clocks = <&usb_mp_clk>; + clock-names = "otg"; + resets = <&rst USB1_RESET>; + reset-names = "dwc2"; + phys = <&usbphy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + watchdog0: watchdog@ffd02000 { + compatible = "snps,dw-wdt"; + reg = <0xffd02000 0x1000>; + interrupts = <0 171 4>; + clocks = <&osc1>; + resets = <&rst L4WD0_RESET>; + status = "disabled"; + }; + + watchdog1: watchdog@ffd03000 { + compatible = "snps,dw-wdt"; + reg = <0xffd03000 0x1000>; + interrupts = <0 172 4>; + clocks = <&osc1>; + resets = <&rst L4WD1_RESET>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi new file mode 100644 index 000000000000..72c55e5187ca --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10.dtsi @@ -0,0 +1,920 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright Altera Corporation (C) 2014. All rights reserved. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset/altr,rst-mgr-a10.h> + +/ { + #address-cells = <1>; + #size-cells = <1>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + enable-method = "altr,socfpga-a10-smp"; + + cpu0: cpu@0 { + compatible = "arm,cortex-a9"; + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2>; + }; + cpu1: cpu@1 { + compatible = "arm,cortex-a9"; + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2>; + }; + }; + + pmu: pmu@ff111000 { + compatible = "arm,cortex-a9-pmu"; + interrupt-parent = <&intc>; + interrupts = <0 124 4>, <0 125 4>; + interrupt-affinity = <&cpu0>, <&cpu1>; + reg = <0xff111000 0x1000>, + <0xff113000 0x1000>; + }; + + intc: interrupt-controller@ffffd000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0xffffd000 0x1000>, + <0xffffc100 0x100>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + device_type = "soc"; + interrupt-parent = <&intc>; + ranges; + + amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pdma: pdma@ffda1000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0xffda1000 0x1000>; + interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>, + <0 84 IRQ_TYPE_LEVEL_HIGH>, + <0 85 IRQ_TYPE_LEVEL_HIGH>, + <0 86 IRQ_TYPE_LEVEL_HIGH>, + <0 87 IRQ_TYPE_LEVEL_HIGH>, + <0 88 IRQ_TYPE_LEVEL_HIGH>, + <0 89 IRQ_TYPE_LEVEL_HIGH>, + <0 90 IRQ_TYPE_LEVEL_HIGH>, + <0 91 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + clocks = <&l4_main_clk>; + clock-names = "apb_pclk"; + resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>; + reset-names = "dma", "dma-ocp"; + }; + }; + + base_fpga_region { + #address-cells = <0x1>; + #size-cells = <0x1>; + + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr>; + }; + + clkmgr@ffd04000 { + compatible = "altr,clk-mgr"; + reg = <0xffd04000 0x1000>; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + cb_intosc_hs_div2_clk: cb_intosc_hs_div2_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + cb_intosc_ls_clk: cb_intosc_ls_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + f2s_free_clk: f2s_free_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + osc1: osc1 { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; + + main_pll: main_pll@40 { + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + compatible = "altr,socfpga-a10-pll-clock"; + clocks = <&osc1>, <&cb_intosc_ls_clk>, + <&f2s_free_clk>; + reg = <0x40>; + + main_mpu_base_clk: main_mpu_base_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + div-reg = <0x140 0 11>; + }; + + main_noc_base_clk: main_noc_base_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + div-reg = <0x144 0 11>; + }; + + main_emaca_clk: main_emaca_clk@68 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x68>; + }; + + main_emacb_clk: main_emacb_clk@6c { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x6C>; + }; + + main_emac_ptp_clk: main_emac_ptp_clk@70 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x70>; + }; + + main_gpio_db_clk: main_gpio_db_clk@74 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x74>; + }; + + main_sdmmc_clk: main_sdmmc_clk@78 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk" +; + clocks = <&main_pll>; + reg = <0x78>; + }; + + main_s2f_usr0_clk: main_s2f_usr0_clk@7c { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x7C>; + }; + + main_s2f_usr1_clk: main_s2f_usr1_clk@80 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x80>; + }; + + main_hmc_pll_ref_clk: main_hmc_pll_ref_clk@84 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x84>; + }; + + main_periph_ref_clk: main_periph_ref_clk@9c { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_pll>; + reg = <0x9C>; + }; + }; + + periph_pll: periph_pll@c0 { + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + compatible = "altr,socfpga-a10-pll-clock"; + clocks = <&osc1>, <&cb_intosc_ls_clk>, + <&f2s_free_clk>, <&main_periph_ref_clk>; + reg = <0xC0>; + + peri_mpu_base_clk: peri_mpu_base_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + div-reg = <0x140 16 11>; + }; + + peri_noc_base_clk: peri_noc_base_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + div-reg = <0x144 16 11>; + }; + + peri_emaca_clk: peri_emaca_clk@e8 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0xE8>; + }; + + peri_emacb_clk: peri_emacb_clk@ec { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0xEC>; + }; + + peri_emac_ptp_clk: peri_emac_ptp_clk@f0 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0xF0>; + }; + + peri_gpio_db_clk: peri_gpio_db_clk@f4 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0xF4>; + }; + + peri_sdmmc_clk: peri_sdmmc_clk@f8 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0xF8>; + }; + + peri_s2f_usr0_clk: peri_s2f_usr0_clk@fc { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0xFC>; + }; + + peri_s2f_usr1_clk: peri_s2f_usr1_clk@100 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0x100>; + }; + + peri_hmc_pll_ref_clk: peri_hmc_pll_ref_clk@104 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&periph_pll>; + reg = <0x104>; + }; + }; + + mpu_free_clk: mpu_free_clk@60 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_mpu_base_clk>, <&peri_mpu_base_clk>, + <&osc1>, <&cb_intosc_hs_div2_clk>, + <&f2s_free_clk>; + reg = <0x60>; + }; + + noc_free_clk: noc_free_clk@64 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_noc_base_clk>, <&peri_noc_base_clk>, + <&osc1>, <&cb_intosc_hs_div2_clk>, + <&f2s_free_clk>; + reg = <0x64>; + }; + + s2f_user1_free_clk: s2f_user1_free_clk@104 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_s2f_usr1_clk>, <&peri_s2f_usr1_clk>, + <&osc1>, <&cb_intosc_hs_div2_clk>, + <&f2s_free_clk>; + reg = <0x104>; + }; + + sdmmc_free_clk: sdmmc_free_clk@f8 { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&main_sdmmc_clk>, <&peri_sdmmc_clk>, + <&osc1>, <&cb_intosc_hs_div2_clk>, + <&f2s_free_clk>; + fixed-divider = <4>; + reg = <0xF8>; + }; + + l4_sys_free_clk: l4_sys_free_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-perip-clk"; + clocks = <&noc_free_clk>; + fixed-divider = <4>; + }; + + l4_main_clk: l4_main_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&noc_free_clk>; + div-reg = <0xA8 0 2>; + clk-gate = <0x48 1>; + }; + + l4_mp_clk: l4_mp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&noc_free_clk>; + div-reg = <0xA8 8 2>; + clk-gate = <0x48 2>; + }; + + l4_sp_clk: l4_sp_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&noc_free_clk>; + div-reg = <0xA8 16 2>; + clk-gate = <0x48 3>; + }; + + mpu_periph_clk: mpu_periph_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&mpu_free_clk>; + fixed-divider = <4>; + clk-gate = <0x48 0>; + }; + + sdmmc_clk: sdmmc_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&sdmmc_free_clk>; + clk-gate = <0xC8 5>; + }; + + qspi_clk: qspi_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&l4_main_clk>; + clk-gate = <0xC8 11>; + }; + + nand_x_clk: nand_x_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&l4_mp_clk>; + clk-gate = <0xC8 10>; + }; + + nand_ecc_clk: nand_ecc_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&nand_x_clk>; + clk-gate = <0xC8 10>; + }; + + nand_clk: nand_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&nand_x_clk>; + fixed-divider = <4>; + clk-gate = <0xC8 10>; + }; + + spi_m_clk: spi_m_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&l4_main_clk>; + clk-gate = <0xC8 9>; + }; + + usb_clk: usb_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&l4_mp_clk>; + clk-gate = <0xC8 8>; + }; + + s2f_usr1_clk: s2f_usr1_clk { + #clock-cells = <0>; + compatible = "altr,socfpga-a10-gate-clk"; + clocks = <&peri_s2f_usr1_clk>; + clk-gate = <0xC8 6>; + }; + }; + }; + + socfpga_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <0 0 0 0 16 0 0>; + }; + + gmac0: ethernet@ff800000 { + compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.72a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x44 0>; + reg = <0xff800000 0x2000>; + interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + /* Filled in by bootloader */ + mac-address = [00 00 00 00 00 00]; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + tx-fifo-depth = <4096>; + rx-fifo-depth = <16384>; + clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>; + clock-names = "stmmaceth", "ptp_ref"; + resets = <&rst EMAC0_RESET>, <&rst EMAC0_OCP_RESET>; + reset-names = "stmmaceth", "stmmaceth-ocp"; + snps,axi-config = <&socfpga_axi_setup>; + status = "disabled"; + }; + + gmac1: ethernet@ff802000 { + compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.72a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x48 8>; + reg = <0xff802000 0x2000>; + interrupts = <0 93 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + /* Filled in by bootloader */ + mac-address = [00 00 00 00 00 00]; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + tx-fifo-depth = <4096>; + rx-fifo-depth = <16384>; + clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>; + clock-names = "stmmaceth", "ptp_ref"; + resets = <&rst EMAC1_RESET>, <&rst EMAC1_OCP_RESET>; + reset-names = "stmmaceth", "stmmaceth-ocp"; + snps,axi-config = <&socfpga_axi_setup>; + status = "disabled"; + }; + + gmac2: ethernet@ff804000 { + compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.72a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x4C 16>; + reg = <0xff804000 0x2000>; + interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + /* Filled in by bootloader */ + mac-address = [00 00 00 00 00 00]; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + tx-fifo-depth = <4096>; + rx-fifo-depth = <16384>; + clocks = <&l4_mp_clk>, <&peri_emac_ptp_clk>; + clock-names = "stmmaceth", "ptp_ref"; + resets = <&rst EMAC2_RESET>, <&rst EMAC2_OCP_RESET>; + reset-names = "stmmaceth", "stmmaceth-ocp"; + snps,axi-config = <&socfpga_axi_setup>; + status = "disabled"; + }; + + gpio0: gpio@ffc02900 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xffc02900 0x100>; + resets = <&rst GPIO0_RESET>; + status = "disabled"; + + porta: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <29>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 112 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio1: gpio@ffc02a00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xffc02a00 0x100>; + resets = <&rst GPIO1_RESET>; + status = "disabled"; + + portb: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <29>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 113 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpio2: gpio@ffc02b00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dw-apb-gpio"; + reg = <0xffc02b00 0x100>; + resets = <&rst GPIO2_RESET>; + status = "disabled"; + + portc: gpio-controller@0 { + compatible = "snps,dw-apb-gpio-port"; + gpio-controller; + #gpio-cells = <2>; + snps,nr-gpios = <27>; + reg = <0>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 114 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + fpga_mgr: fpga-mgr@ffd03000 { + compatible = "altr,socfpga-a10-fpga-mgr"; + reg = <0xffd03000 0x100 + 0xffcfe400 0x20>; + clocks = <&l4_mp_clk>; + resets = <&rst FPGAMGR_RESET>; + reset-names = "fpgamgr"; + }; + + i2c0: i2c@ffc02200 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02200 0x100>; + interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; + resets = <&rst I2C0_RESET>; + status = "disabled"; + }; + + i2c1: i2c@ffc02300 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02300 0x100>; + interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; + resets = <&rst I2C1_RESET>; + status = "disabled"; + }; + + i2c2: i2c@ffc02400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02400 0x100>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; + resets = <&rst I2C2_RESET>; + status = "disabled"; + }; + + i2c3: i2c@ffc02500 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02500 0x100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; + resets = <&rst I2C3_RESET>; + status = "disabled"; + }; + + i2c4: i2c@ffc02600 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,designware-i2c"; + reg = <0xffc02600 0x100>; + interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sp_clk>; + resets = <&rst I2C4_RESET>; + status = "disabled"; + }; + + spi0: spi@ffda4000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xffda4000 0x100>; + interrupts = <0 101 4>; + num-cs = <4>; + /*32bit_access;*/ + clocks = <&spi_m_clk>; + resets = <&rst SPIM0_RESET>; + reset-names = "spi"; + status = "disabled"; + }; + + spi1: spi@ffda5000 { + compatible = "snps,dw-apb-ssi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xffda5000 0x100>; + interrupts = <0 102 4>; + num-cs = <4>; + /*32bit_access;*/ + tx-dma-channel = <&pdma 16>; + rx-dma-channel = <&pdma 17>; + clocks = <&spi_m_clk>; + resets = <&rst SPIM1_RESET>; + reset-names = "spi"; + status = "disabled"; + }; + + sdr: sdr@ffcfb100 { + compatible = "altr,sdr-ctl", "syscon"; + reg = <0xffcfb100 0x80>; + }; + + L2: cache-controller@fffff000 { + compatible = "arm,pl310-cache"; + reg = <0xfffff000 0x1000>; + interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; + cache-unified; + cache-level = <2>; + prefetch-data = <1>; + prefetch-instr = <1>; + arm,shared-override; + }; + + mmc: mmc@ff808000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "altr,socfpga-dw-mshc"; + reg = <0xff808000 0x1000>; + interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>; + fifo-depth = <0x400>; + clocks = <&l4_mp_clk>, <&sdmmc_clk>; + clock-names = "biu", "ciu"; + resets = <&rst SDMMC_RESET>; + altr,sysmgr-syscon = <&sysmgr 0x28 4>; + status = "disabled"; + }; + + nand: nand@ffb90000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "altr,socfpga-denali-nand"; + reg = <0xffb90000 0x72000>, + <0xffb80000 0x10000>; + reg-names = "nand_data", "denali_reg"; + interrupts = <0 99 4>; + clocks = <&nand_clk>, <&nand_x_clk>, <&nand_ecc_clk>; + clock-names = "nand", "nand_x", "ecc"; + resets = <&rst NAND_RESET>; + status = "disabled"; + }; + + ocram: sram@ffe00000 { + compatible = "mmio-sram"; + reg = <0xffe00000 0x40000>; + }; + + eccmgr: eccmgr { + compatible = "altr,socfpga-a10-ecc-manager"; + altr,sysmgr-syscon = <&sysmgr>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>, + <0 0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <2>; + ranges; + + sdramedac { + compatible = "altr,sdram-edac-a10"; + altr,sdr-syscon = <&sdr>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>, + <49 IRQ_TYPE_LEVEL_HIGH>; + }; + + l2-ecc@ffd06010 { + compatible = "altr,socfpga-a10-l2-ecc"; + reg = <0xffd06010 0x4>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>, + <32 IRQ_TYPE_LEVEL_HIGH>; + }; + + ocram-ecc@ff8c3000 { + compatible = "altr,socfpga-a10-ocram-ecc"; + reg = <0xff8c3000 0x400>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>, + <33 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-rx-ecc@ff8c0800 { + compatible = "altr,socfpga-eth-mac-ecc"; + reg = <0xff8c0800 0x400>; + altr,ecc-parent = <&gmac0>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>, + <36 IRQ_TYPE_LEVEL_HIGH>; + }; + + emac0-tx-ecc@ff8c0c00 { + compatible = "altr,socfpga-eth-mac-ecc"; + reg = <0xff8c0c00 0x400>; + altr,ecc-parent = <&gmac0>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>, + <37 IRQ_TYPE_LEVEL_HIGH>; + }; + + sdmmca-ecc@ff8c2c00 { + compatible = "altr,socfpga-sdmmc-ecc"; + reg = <0xff8c2c00 0x400>; + altr,ecc-parent = <&mmc>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH>, + <47 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>, + <48 IRQ_TYPE_LEVEL_HIGH>; + }; + + dma-ecc@ff8c8000 { + compatible = "altr,socfpga-dma-ecc"; + reg = <0xff8c8000 0x400>; + altr,ecc-parent = <&pdma>; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <42 IRQ_TYPE_LEVEL_HIGH>; + }; + + usb0-ecc@ff8c8800 { + compatible = "altr,socfpga-usb-ecc"; + reg = <0xff8c8800 0x400>; + altr,ecc-parent = <&usb0>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>, + <34 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + qspi: spi@ff809000 { + compatible = "intel,socfpga-qspi", "cdns,qspi-nor"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0xff809000 0x100>, + <0xffa00000 0x100000>; + interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <128>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x00000000>; + clocks = <&qspi_clk>; + resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>; + reset-names = "qspi", "qspi-ocp"; + status = "disabled"; + }; + + rst: rstmgr@ffd05000 { + #reset-cells = <1>; + compatible = "altr,rst-mgr"; + reg = <0xffd05000 0x100>; + altr,modrst-offset = <0x20>; + }; + + scu: snoop-control-unit@ffffc000 { + compatible = "arm,cortex-a9-scu"; + reg = <0xffffc000 0x100>; + }; + + sysmgr: sysmgr@ffd06000 { + compatible = "altr,sys-mgr", "syscon"; + reg = <0xffd06000 0x300>; + cpu1-start-addr = <0xffd06230>; + }; + + /* Local timer */ + timer@ffffc600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xffffc600 0x100>; + interrupts = <1 13 0xf01>; + clocks = <&mpu_periph_clk>; + }; + + timer0: timer0@ffc02700 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 115 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xffc02700 0x100>; + clocks = <&l4_sp_clk>; + clock-names = "timer"; + resets = <&rst SPTIMER0_RESET>; + reset-names = "timer"; + }; + + timer1: timer1@ffc02800 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 116 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xffc02800 0x100>; + clocks = <&l4_sp_clk>; + clock-names = "timer"; + resets = <&rst SPTIMER1_RESET>; + reset-names = "timer"; + }; + + timer2: timer2@ffd00000 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 117 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xffd00000 0x100>; + clocks = <&l4_sys_free_clk>; + clock-names = "timer"; + resets = <&rst L4SYSTIMER0_RESET>; + reset-names = "timer"; + }; + + timer3: timer3@ffd00100 { + compatible = "snps,dw-apb-timer"; + interrupts = <0 118 IRQ_TYPE_LEVEL_HIGH>; + reg = <0xffd00100 0x100>; + clocks = <&l4_sys_free_clk>; + clock-names = "timer"; + resets = <&rst L4SYSTIMER1_RESET>; + reset-names = "timer"; + }; + + uart0: serial@ffc02000 { + compatible = "snps,dw-apb-uart"; + reg = <0xffc02000 0x100>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&l4_sp_clk>; + resets = <&rst UART0_RESET>; + status = "disabled"; + }; + + uart1: serial@ffc02100 { + compatible = "snps,dw-apb-uart"; + reg = <0xffc02100 0x100>; + interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&l4_sp_clk>; + resets = <&rst UART1_RESET>; + status = "disabled"; + }; + + usbphy0: usbphy { + #phy-cells = <0>; + compatible = "usb-nop-xceiv"; + status = "okay"; + }; + + usb0: usb@ffb00000 { + compatible = "snps,dwc2"; + reg = <0xffb00000 0xffff>; + interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&usb_clk>; + clock-names = "otg"; + resets = <&rst USB0_RESET>; + reset-names = "dwc2"; + phys = <&usbphy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + usb1: usb@ffb40000 { + compatible = "snps,dwc2"; + reg = <0xffb40000 0xffff>; + interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&usb_clk>; + clock-names = "otg"; + resets = <&rst USB1_RESET>; + reset-names = "dwc2"; + phys = <&usbphy0>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + watchdog0: watchdog@ffd00200 { + compatible = "snps,dw-wdt"; + reg = <0xffd00200 0x100>; + interrupts = <0 119 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sys_free_clk>; + resets = <&rst L4WD0_RESET>; + status = "disabled"; + }; + + watchdog1: watchdog@ffd00300 { + compatible = "snps,dw-wdt"; + reg = <0xffd00300 0x100>; + interrupts = <0 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&l4_sys_free_clk>; + resets = <&rst L4WD1_RESET>; + status = "disabled"; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts new file mode 100644 index 000000000000..422d00cd4c74 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_chameleonv3.dts @@ -0,0 +1,90 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2022 Google LLC + */ +/dts-v1/; +#include "socfpga_arria10_mercury_aa1.dtsi" + +/ { + model = "Google Chameleon V3"; + compatible = "google,chameleon-v3", "enclustra,mercury-aa1", + "altr,socfpga-arria10", "altr,socfpga"; + + aliases { + serial0 = &uart0; + i2c0 = &i2c0; + i2c1 = &i2c1; + }; +}; + +&gmac0 { + status = "okay"; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + ssm2603: audio-codec@1a { + compatible = "adi,ssm2603"; + reg = <0x1a>; + }; +}; + +&i2c1 { + status = "okay"; + + u80: gpio@21 { + compatible = "nxp,pca9535"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + + gpio-line-names = + "SOM_AUD_MUTE", + "DP1_OUT_CEC_EN", + "DP2_OUT_CEC_EN", + "DP1_SOM_PS8469_CAD", + "DPD_SOM_PS8469_CAD", + "DP_OUT_PWR_EN", + "STM32_RST_L", + "STM32_BOOT0", + + "FPGA_PROT", + "STM32_FPGA_COMM0", + "TP119", + "TP120", + "TP121", + "TP122", + "TP123", + "TP124"; + }; +}; + +&mmc { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "host"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi new file mode 100644 index 000000000000..41f865c8c098 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_aa1.dtsi @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2022 Google LLC + */ + +#include "socfpga_arria10.dtsi" + +/ { + + model = "Enclustra Mercury AA1"; + compatible = "enclustra,mercury-aa1", "altr,socfpga-arria10", "altr,socfpga"; + + aliases { + ethernet0 = &gmac0; + serial1 = &uart1; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x80000000>; /* 2GB */ + }; + + chosen { + stdout-path = "serial1:115200n8"; + }; +}; + +&gmac0 { + phy-mode = "rgmii"; + phy-addr = <0xffffffff>; /* probe for phy addr */ + + max-frame-size = <3800>; + + phy-handle = <&phy3>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy3: ethernet-phy@3 { + txd0-skew-ps = <0>; /* -420ps */ + txd1-skew-ps = <0>; /* -420ps */ + txd2-skew-ps = <0>; /* -420ps */ + txd3-skew-ps = <0>; /* -420ps */ + rxd0-skew-ps = <420>; /* 0ps */ + rxd1-skew-ps = <420>; /* 0ps */ + rxd2-skew-ps = <420>; /* 0ps */ + rxd3-skew-ps = <420>; /* 0ps */ + txen-skew-ps = <0>; /* -420ps */ + txc-skew-ps = <1860>; /* 960ps */ + rxdv-skew-ps = <420>; /* 0ps */ + rxc-skew-ps = <1680>; /* 780ps */ + reg = <3>; + }; + }; +}; + +&i2c1 { + atsha204a: crypto@64 { + compatible = "atmel,atsha204a"; + reg = <0x64>; + }; + + isl12022: isl12022@6f { + compatible = "isil,isl12022"; + reg = <0x6f>; + }; +}; + +/* Following mappings are taken from arria10 socdk dts */ +&mmc { + cap-sd-highspeed; + broken-cd; + bus-width = <4>; + clk-phase-sd-hs = <0>, <135>; +}; + +&osc1 { + clock-frequency = <33330000>; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts new file mode 100644 index 000000000000..cf533f76a9fd --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_mercury_pe1.dts @@ -0,0 +1,55 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2023 Steffen Trumtrar <kernel@pengutronix.de> + */ +/dts-v1/; +#include "socfpga_arria10_mercury_aa1.dtsi" + +/ { + model = "Enclustra Mercury+ PE1"; + compatible = "enclustra,mercury-pe1", "enclustra,mercury-aa1", + "altr,socfpga-arria10", "altr,socfpga"; + + aliases { + ethernet0 = &gmac0; + serial0 = &uart0; + serial1 = &uart1; + }; +}; + +&gmac0 { + status = "okay"; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&mmc { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + dr_mode = "host"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi new file mode 100644 index 000000000000..ec7365444a3b --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk.dtsi @@ -0,0 +1,183 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2015 Altera Corporation <www.altera.com> + */ +#include "socfpga_arria10.dtsi" + +/ { + model = "Altera SOCFPGA Arria 10"; + compatible = "altr,socfpga-arria10-socdk", "altr,socfpga-arria10", "altr,socfpga"; + + aliases { + ethernet0 = &gmac0; + serial0 = &uart1; + }; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + a10leds { + compatible = "gpio-leds"; + + a10sr_led0 { + label = "a10sr-led0"; + gpios = <&a10sr_gpio 0 1>; + }; + + a10sr_led1 { + label = "a10sr-led1"; + gpios = <&a10sr_gpio 1 1>; + }; + + a10sr_led2 { + label = "a10sr-led2"; + gpios = <&a10sr_gpio 2 1>; + }; + + a10sr_led3 { + label = "a10sr-led3"; + gpios = <&a10sr_gpio 3 1>; + }; + }; + + ref_033v: 033-v-ref { + compatible = "regulator-fixed"; + regulator-name = "0.33V"; + regulator-min-microvolt = <330000>; + regulator-max-microvolt = <330000>; + }; + + soc { + clkmgr@ffd04000 { + clocks { + osc1 { + clock-frequency = <25000000>; + }; + }; + }; + }; +}; + +&gmac0 { + phy-mode = "rgmii"; + phy-addr = <0xffffffff>; /* probe for phy addr */ + + /* + * These skews assume the user's FPGA design is adding 600ps of delay + * for TX_CLK on Arria 10. + * + * All skews are offset since hardware skew values for the ksz9031 + * range from a negative skew to a positive skew. + * See the micrel-ksz90x1.txt Documentation file for details. + */ + txd0-skew-ps = <0>; /* -420ps */ + txd1-skew-ps = <0>; /* -420ps */ + txd2-skew-ps = <0>; /* -420ps */ + txd3-skew-ps = <0>; /* -420ps */ + rxd0-skew-ps = <420>; /* 0ps */ + rxd1-skew-ps = <420>; /* 0ps */ + rxd2-skew-ps = <420>; /* 0ps */ + rxd3-skew-ps = <420>; /* 0ps */ + txen-skew-ps = <0>; /* -420ps */ + txc-skew-ps = <1860>; /* 960ps */ + rxdv-skew-ps = <420>; /* 0ps */ + rxc-skew-ps = <1680>; /* 780ps */ + max-frame-size = <3800>; + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&spi1 { + status = "okay"; + + resource-manager@0 { + compatible = "altr,a10sr"; + reg = <0>; + spi-max-frequency = <100000>; + /* low-level active IRQ at GPIO1_5 */ + interrupt-parent = <&portb>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + a10sr_gpio: gpio-controller { + compatible = "altr,a10sr-gpio"; + gpio-controller; + #gpio-cells = <2>; + }; + + a10sr_rst: reset-controller { + compatible = "altr,a10sr-reset"; + #reset-cells = <1>; + }; + }; +}; + +&i2c1 { + status = "okay"; + + /* + * adjust the falling times to decrease the i2c frequency to 50Khz + * because the LCD module does not work at the standard 100Khz + */ + clock-frequency = <100000>; + i2c-sda-falling-time-ns = <6000>; + i2c-scl-falling-time-ns = <6000>; + + adc@14 { + compatible = "lltc,ltc2497"; + reg = <0x14>; + vref-supply = <&ref_033v>; + }; + + adc@16 { + compatible = "lltc,ltc2497"; + reg = <0x16>; + vref-supply = <&ref_033v>; + }; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; + + ltc@5c { + compatible = "ltc2977"; + reg = <0x5c>; + }; + + temp@4c { + compatible = "maxim,max1619"; + reg = <0x4c>; + }; +}; + +&uart1 { + status = "okay"; +}; + +&usb0 { + status = "okay"; + disable-over-current; +}; + +&watchdog1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts new file mode 100644 index 000000000000..a662df319a84 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_nand.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2015 Altera Corporation. All rights reserved. + */ + +/dts-v1/; +#include "socfpga_arria10_socdk.dtsi" + +&nand { + status = "okay"; + + nand@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Boot and fpga data"; + reg = <0x0 0x02500000>; + }; + partition@1c00000 { + label = "Root Filesystem - JFFS2"; + reg = <0x02500000 0x05500000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts new file mode 100644 index 000000000000..11ccdc6c2dc6 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_qspi.dts @@ -0,0 +1,38 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2016 Intel. All rights reserved. + */ + +/dts-v1/; +#include "socfpga_arria10_socdk.dtsi" + +&qspi { + status = "okay"; + + flash0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,mt25qu02g", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <100000000>; + + m25p,fast-read; + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <3>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + + partition@qspi-boot { + label = "Boot and fpga data"; + reg = <0x0 0x2720000>; + }; + + partition@qspi-rootfs { + label = "Root Filesystem - JFFS2"; + reg = <0x2720000 0x58E0000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts new file mode 100644 index 000000000000..d3969367f4b5 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria10_socdk_sdmmc.dts @@ -0,0 +1,28 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2014-2015 Altera Corporation <www.altera.com> + */ + +/dts-v1/; +#include "socfpga_arria10_socdk.dtsi" + +&mmc { + status = "okay"; + cap-sd-highspeed; + cap-mmc-highspeed; + broken-cd; + bus-width = <4>; + clk-phase-sd-hs = <0>, <135>; +}; + +&eccmgr { + sdmmca-ecc@ff8c2c00 { + compatible = "altr,socfpga-sdmmc-ecc"; + reg = <0xff8c2c00 0x400>; + altr,ecc-parent = <&mmc>; + interrupts = <15 IRQ_TYPE_LEVEL_HIGH>, + <47 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>, + <48 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi new file mode 100644 index 000000000000..40fecde65c54 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5.dtsi @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + */ + +/dts-v1/; +/* First 4KB has trampoline code for secondary cores. */ +/memreserve/ 0x00000000 0x0001000; +#include "socfpga.dtsi" + +/ { + soc { + clkmgr@ffd04000 { + clocks { + osc1 { + clock-frequency = <25000000>; + }; + }; + }; + + mmc0: mmc@ff704000 { + broken-cd; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + clk-phase-sd-hs = <0>, <135>; + }; + + sysmgr@ffd08000 { + cpu1-start-addr = <0xffd080c4>; + }; + }; +}; + +&watchdog0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts new file mode 100644 index 000000000000..c48385702a85 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_arria5_socdk.dts @@ -0,0 +1,151 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + */ + +#include "socfpga_arria5.dtsi" + +/ { + model = "Altera SOCFPGA Arria V SoC Development Kit"; + compatible = "altr,socfpga-arria5-socdk", "altr,socfpga-arria5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; + + leds { + compatible = "gpio-leds"; + led-hps0 { + label = "hps_led0"; + gpios = <&porta 0 1>; + }; + + led-hps1 { + label = "hps_led1"; + gpios = <&portb 11 1>; + }; + + led-hps2 { + label = "hps_led2"; + gpios = <&porta 17 1>; + }; + + led-hps3 { + label = "hps_led3"; + gpios = <&porta 18 1>; + }; + }; + + regulator_3_3v: regulator { + compatible = "regulator-fixed"; + regulator-name = "3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <2600>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <2000>; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + + /* + * adjust the falling times to decrease the i2c frequency to 50Khz + * because the LCD module does not work at the standard 100Khz + */ + i2c-sda-falling-time-ns = <5000>; + i2c-scl-falling-time-ns = <5000>; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; + +&mmc0 { + vmmc-supply = <®ulator_3_3v>; + vqmmc-supply = <®ulator_3_3v>; + status = "okay"; +}; + +&qspi { + status = "okay"; + + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <100000000>; + + m25p,fast-read; + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + + partition@qspi-boot { + /* 8MB for raw data. */ + label = "Flash 0 Raw Data"; + reg = <0x0 0x800000>; + }; + + partition@qspi-rootfs { + /* 120MB for jffs2 data. */ + label = "Flash 0 jffs2 Filesystem"; + reg = <0x800000 0x7800000>; + }; + }; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi new file mode 100644 index 000000000000..305fe207b237 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5.dtsi @@ -0,0 +1,37 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2012 Altera Corporation <www.altera.com> + */ + +/dts-v1/; +/* First 4KB has trampoline code for secondary cores. */ +/memreserve/ 0x00000000 0x0001000; +#include "socfpga.dtsi" + +/ { + soc { + clkmgr@ffd04000 { + clocks { + osc1 { + clock-frequency = <25000000>; + }; + }; + }; + + mmc0: mmc@ff704000 { + broken-cd; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + clk-phase-sd-hs = <0>, <135>; + }; + + sysmgr@ffd08000 { + cpu1-start-addr = <0xffd080c4>; + }; + }; +}; + +&watchdog0 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts new file mode 100644 index 000000000000..76262f1e5e03 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_chameleon96.dts @@ -0,0 +1,130 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Device Tree file for the Chameleon96 + * + * Copyright (c) 2018 Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> + */ + +#include <dt-bindings/gpio/gpio.h> + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "Novetech Chameleon96"; + compatible = "novtech,chameleon96", "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x20000000>; /* 512MB */ + }; + + regulator_3_3v: regulator { + compatible = "regulator-fixed"; + regulator-name = "3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + leds { + compatible = "gpio-leds"; + + user_led1 { + label = "green:user1"; + gpios = <&porta 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + + user_led2 { + label = "green:user2"; + gpios = <&porta 22 GPIO_ACTIVE_LOW>; + linux,default-trigger = "mmc0"; + }; + + user_led3 { + label = "green:user3"; + gpios = <&porta 25 GPIO_ACTIVE_LOW>; + linux,default-trigger = "none"; + }; + + user_led4 { + label = "green:user4"; + gpios = <&portb 3 GPIO_ACTIVE_LOW>; + panic-indicator; + linux,default-trigger = "none"; + }; + }; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&i2c0 { + /* On Low speed expansion */ + label = "LS-I2C0"; + status = "okay"; +}; + +&i2c1 { + /* On Low speed expansion */ + label = "LS-I2C1"; + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + /* On High speed expansion */ + label = "HS-I2C2"; + status = "okay"; +}; + +&mmc0 { + vmmc-supply = <®ulator_3_3v>; + vqmmc-supply = <®ulator_3_3v>; + status = "okay"; +}; + +&spi0 { + /* On High speed expansion */ + label = "HS-SPI1"; + status = "okay"; +}; + +&spi1 { + /* On Low speed expansion */ + label = "LS-SPI0"; + status = "okay"; +}; + +&uart0 { + /* On Low speed expansion */ + label = "LS-UART1"; + status = "okay"; +}; + +&uart1 { + /* On Low speed expansion */ + label = "LS-UART0"; + status = "okay"; +}; + +&usbphy0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts new file mode 100644 index 000000000000..bedf577cb056 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_de0_nano_soc.dts @@ -0,0 +1,101 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright Altera Corporation (C) 2015. All rights reserved. + */ + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "Terasic DE-0(Atlas)"; + compatible = "terasic,de0-atlas", "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + ethernet0 = &gmac1; + }; + + regulator_3_3v: regulator { + compatible = "regulator-fixed"; + regulator-name = "3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + leds { + compatible = "gpio-leds"; + led-hps0 { + label = "hps_led0"; + gpios = <&portb 24 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + + txd0-skew-ps = <0>; /* -420ps */ + txd1-skew-ps = <0>; /* -420ps */ + txd2-skew-ps = <0>; /* -420ps */ + txd3-skew-ps = <0>; /* -420ps */ + rxd0-skew-ps = <420>; /* 0ps */ + rxd1-skew-ps = <420>; /* 0ps */ + rxd2-skew-ps = <420>; /* 0ps */ + rxd3-skew-ps = <420>; /* 0ps */ + txen-skew-ps = <0>; /* -420ps */ + txc-skew-ps = <1860>; /* 960ps */ + rxdv-skew-ps = <420>; /* 0ps */ + rxc-skew-ps = <1680>; /* 780ps */ + + max-frame-size = <3800>; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + + adxl345: adxl345@53 { + compatible = "adi,adxl345"; + reg = <0x53>; + + interrupt-parent = <&portc>; + interrupts = <3 2>; + }; +}; + +&mmc0 { + vmmc-supply = <®ulator_3_3v>; + vqmmc-supply = <®ulator_3_3v>; + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi new file mode 100644 index 000000000000..3b9daddf91cd --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcv.dtsi @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2015 Marek Vasut <marex@denx.de> + */ + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "Aries/DENX MCV"; + compatible = "altr,socfpga-cyclone5", "altr,socfpga"; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1 GiB */ + }; +}; + +&mmc0 { /* On-SoM eMMC */ + bus-width = <8>; + clk-phase-sd-hs = <0>, <135>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts new file mode 100644 index 000000000000..ceaec29770c6 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_mcvevk.dts @@ -0,0 +1,81 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2015 Marek Vasut <marex@denx.de> + */ + +#include "socfpga_cyclone5_mcv.dtsi" + +/ { + model = "Aries/DENX MCV EVK"; + compatible = "denx,mcvevk", "altr,socfpga-cyclone5", "altr,socfpga"; + + aliases { + ethernet0 = &gmac0; + stmpe-i2c0 = &stmpe1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&can0 { + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + +&gmac0 { + phy-mode = "rgmii"; + status = "okay"; +}; + +&gpio0 { /* GPIO 0 ... 28 */ + status = "okay"; +}; + +&gpio1 { /* GPIO 29 ... 57 */ + status = "okay"; +}; + +&gpio2 { /* GPIO 58..66 (HLGPI 0..13 at offset 13) */ + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + + stmpe1: stmpe811@41 { + compatible = "st,stmpe811"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x41>; + id = <0>; + blocks = <0x5>; + irq-gpio = <&portb 28 0x4>; /* GPIO 57, trig. level HI */ + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + ts,sample-time = <4>; + ts,mod-12b = <1>; + ts,ref-sel = <0>; + ts,adc-freq = <1>; + ts,ave-ctrl = <1>; + ts,touch-det-delay = <3>; + ts,settling = <4>; + ts,fraction-z = <7>; + ts,i-drive = <1>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts new file mode 100644 index 000000000000..c7f5fa0ba0f2 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socdk.dts @@ -0,0 +1,166 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2012 Altera Corporation <www.altera.com> + */ + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "Altera SOCFPGA Cyclone V SoC Development Kit"; + compatible = "altr,socfpga-cyclone5-socdk", "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; + + leds { + compatible = "gpio-leds"; + led-hps0 { + label = "hps_led0"; + gpios = <&portb 15 1>; + }; + + led-hps1 { + label = "hps_led1"; + gpios = <&portb 14 1>; + }; + + led-hps2 { + label = "hps_led2"; + gpios = <&portb 13 1>; + }; + + led-hps3 { + label = "hps_led3"; + gpios = <&portb 12 1>; + }; + }; + + regulator_3_3v: regulator { + compatible = "regulator-fixed"; + regulator-name = "3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&can0 { + status = "okay"; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <2600>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <2000>; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + clock-frequency = <100000>; + + /* + * adjust the falling times to decrease the i2c frequency to 50Khz + * because the LCD module does not work at the standard 100Khz + */ + i2c-sda-falling-time-ns = <5000>; + i2c-scl-falling-time-ns = <5000>; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; + +&mmc0 { + cd-gpios = <&portb 18 0>; + vmmc-supply = <®ulator_3_3v>; + vqmmc-supply = <®ulator_3_3v>; + status = "okay"; +}; + +&qspi { + status = "okay"; + + flash0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,mt25qu02g", "jedec,spi-nor"; + reg = <0>; /* chip select */ + spi-max-frequency = <100000000>; + + m25p,fast-read; + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + + partition@qspi-boot { + /* 8MB for raw data. */ + label = "Flash 0 Raw Data"; + reg = <0x0 0x800000>; + }; + + partition@qspi-rootfs { + /* 120MB for jffs2 data. */ + label = "Flash 0 jffs2 Filesystem"; + reg = <0x800000 0x7800000>; + }; + }; +}; + +&spi0 { + status = "okay"; + + spidev@0 { + compatible = "rohm,dh2228fv"; + reg = <0>; + spi-max-frequency = <1000000>; + }; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts new file mode 100644 index 000000000000..3dd99c7c95e0 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sockit.dts @@ -0,0 +1,189 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de> + */ + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "Terasic SoCkit"; + compatible = "terasic,socfpga-cyclone5-sockit", "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; + + leds { + compatible = "gpio-leds"; + + hps_led0 { + label = "hps:blue:led0"; + gpios = <&portb 24 0>; /* HPS_GPIO53 */ + linux,default-trigger = "heartbeat"; + }; + + hps_led1 { + label = "hps:blue:led1"; + gpios = <&portb 25 0>; /* HPS_GPIO54 */ + linux,default-trigger = "heartbeat"; + }; + + hps_led2 { + label = "hps:blue:led2"; + gpios = <&portb 26 0>; /* HPS_GPIO55 */ + linux,default-trigger = "heartbeat"; + }; + + hps_led3 { + label = "hps:blue:led3"; + gpios = <&portb 27 0>; /* HPS_GPIO56 */ + linux,default-trigger = "heartbeat"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + hps_sw0 { + label = "hps_sw0"; + gpios = <&portc 20 0>; /* HPS_GPI7 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x0>; /* SW_LID */ + }; + + hps_sw1 { + label = "hps_sw1"; + gpios = <&portc 19 0>; /* HPS_GPI6 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0x5>; /* SW_DOCK */ + }; + + hps_sw2 { + label = "hps_sw2"; + gpios = <&portc 18 0>; /* HPS_GPI5 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0xa>; /* SW_KEYPAD_SLIDE */ + }; + + hps_sw3 { + label = "hps_sw3"; + gpios = <&portc 17 0>; /* HPS_GPI4 */ + linux,input-type = <5>; /* EV_SW */ + linux,code = <0xc>; /* SW_ROTATE_LOCK */ + }; + + hps_hkey0 { + label = "hps_hkey0"; + gpios = <&portc 21 1>; /* HPS_GPI8 */ + linux,code = <187>; /* KEY_F17 */ + }; + + hps_hkey1 { + label = "hps_hkey1"; + gpios = <&portc 22 1>; /* HPS_GPI9 */ + linux,code = <188>; /* KEY_F18 */ + }; + + hps_hkey2 { + label = "hps_hkey2"; + gpios = <&portc 23 1>; /* HPS_GPI10 */ + linux,code = <189>; /* KEY_F19 */ + }; + + hps_hkey3 { + label = "hps_hkey3"; + gpios = <&portc 24 1>; /* HPS_GPI11 */ + linux,code = <190>; /* KEY_F20 */ + }; + }; + + regulator_3_3v: regulator { + compatible = "regulator-fixed"; + regulator-name = "VCC3P3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <2600>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <2000>; +}; + +&gpio0 { /* GPIO 0..29 */ + status = "okay"; +}; + +&gpio1 { /* GPIO 30..57 */ + status = "okay"; +}; + +&gpio2 { /* GPIO 58..66 (HLGPI 0..13 at offset 13) */ + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + accel1: accelerometer@53 { + compatible = "adi,adxl345"; + reg = <0x53>; + + interrupt-parent = <&portc>; + interrupts = <3 2>; + }; +}; + +&mmc0 { + vmmc-supply = <®ulator_3_3v>; + vqmmc-supply = <®ulator_3_3v>; + status = "okay"; +}; + +&qspi { + status = "okay"; + + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,mt25qu02g", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <100000000>; + + m25p,fast-read; + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts new file mode 100644 index 000000000000..ca18b959e655 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_socrates.dts @@ -0,0 +1,94 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2014 Steffen Trumtrar <s.trumtrar@pengutronix.de> + */ + +#include "socfpga_cyclone5.dtsi" + +/ { + model = "EBV SOCrates"; + compatible = "ebv,socrates", "altr,socfpga-cyclone5", "altr,socfpga"; + + aliases { + ethernet0 = &gmac1; + }; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + leds: gpio-leds { + }; +}; + +&gmac1 { + phy-mode = "rgmii"; + status = "okay"; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio1 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + rtc: rtc@68 { + compatible = "st,m41t82"; + reg = <0x68>; + }; +}; + +&leds { + compatible = "gpio-leds"; + + led0 { + label = "led:green:heartbeat"; + gpios = <&porta 28 1>; + linux,default-trigger = "heartbeat"; + }; + + led1 { + label = "led:green:D7"; + gpios = <&portb 19 1>; + }; + + led2 { + label = "led:green:D8"; + gpios = <&portb 25 1>; + }; +}; + +&mmc { + status = "okay"; +}; + +&qspi { + status = "okay"; + + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q256a", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <100000000>; + m25p,fast-read; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts new file mode 100644 index 000000000000..2564671fc1c6 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_sodia.dts @@ -0,0 +1,132 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2016 Nobuhiro Iwamatsu <iwamatsu@nigauri.org> + */ + +#include "socfpga_cyclone5.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "Altera SOCFPGA Cyclone V SoC Macnica Sodia board"; + compatible = "macnica,sodia", "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; + }; + + aliases { + ethernet0 = &gmac1; + }; + + regulator_3_3v: regulator { + compatible = "regulator-fixed"; + regulator-name = "3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + leds: gpio-leds { + compatible = "gpio-leds"; + + hps_led0 { + label = "hps:green:led0"; + gpios = <&portb 12 GPIO_ACTIVE_LOW>; + }; + + hps_led1 { + label = "hps:green:led1"; + gpios = <&portb 13 GPIO_ACTIVE_LOW>; + }; + + hps_led2 { + label = "hps:green:led2"; + gpios = <&portb 14 GPIO_ACTIVE_LOW>; + }; + + hps_led3 { + label = "hps:green:led3"; + gpios = <&portb 15 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + phy = <&phy0>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + }; + }; +}; + +&gpio1 { + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; +}; + +&mmc0 { + cd-gpios = <&portb 18 0>; + vmmc-supply = <®ulator_3_3v>; + vqmmc-supply = <®ulator_3_3v>; + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&qspi { + status = "okay"; + + flash0: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q512a", "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <100000000>; + + m25p,fast-read; + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts new file mode 100644 index 000000000000..e0630b0eed03 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_cyclone5_vining_fpga.dts @@ -0,0 +1,267 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR X11) +/* + * Copyright (C) 2015 Marek Vasut <marex@denx.de> + */ + +#include "socfpga_cyclone5.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + model = "samtec VIN|ING FPGA"; + compatible = "samtec,vining", "altr,socfpga-cyclone5", "altr,socfpga"; + + chosen { + bootargs = "earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1GB */ + }; + + aliases { + /* + * This allow the ethaddr uboot environment variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + ethernet1 = &gmac0; + }; + + gpio-keys { + compatible = "gpio-keys"; + + hps_temp0 { + label = "BTN_0"; /* TEMP_OS */ + gpios = <&portc 18 GPIO_ACTIVE_LOW>; /* HPS_GPI5 */ + linux,code = <BTN_0>; + }; + + hps_hkey0 { + label = "GP_SWITCH"; /* GP_SWITCH */ + gpios = <&portc 19 GPIO_ACTIVE_LOW>; /* HPS_GPI6 */ + linux,code = <BTN_1>; + }; + + hps_hkey1 { + label = "RESET_SWITCH"; /* RESET_SWITCH */ + gpios = <&portc 20 GPIO_ACTIVE_LOW>; /* HPS_GPI7 */ + linux,code = <BTN_2>; + }; + + hps_hkey2 { + label = "POWER_DOWN"; /* POWER_DOWN */ + gpios = <&portc 4 GPIO_ACTIVE_LOW>; /* HPS_GPIO62 */ + linux,code = <KEY_POWER>; + }; + + hps_hkey3 { + label = "SENSE"; /* SENSE */ + gpios = <&porta 9 GPIO_ACTIVE_LOW>; /* HPS_GPIO9 */ + linux,code = <BTN_3>; + }; + }; + + regulator-usb-nrst { + compatible = "regulator-fixed"; + regulator-name = "usb_nrst"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&portb 5 GPIO_ACTIVE_HIGH>; + startup-delay-us = <70000>; + enable-active-high; + regulator-always-on; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + + snps,reset-gpio = <&porta 0 GPIO_ACTIVE_LOW>; + snps,reset-active-low; + snps,reset-delays-us = <10000 10000 10000>; + + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy1: ethernet-phy@1 { + reg = <1>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <1860>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <1860>; + }; + }; +}; + +&gpio0 { /* GPIO 0..29 */ + status = "okay"; +}; + +&gpio1 { /* GPIO 30..57 */ + status = "okay"; +}; + +&gpio2 { /* GPIO 58..66 (HLGPI 0..13 at offset 13) */ + status = "okay"; +}; + +&i2c0 { + status = "okay"; + + gpio: pca9557@1f { + compatible = "nxp,pca9557"; + reg = <0x1f>; + gpio-controller; + #gpio-cells = <2>; + }; + + temp: lm75@48 { + compatible = "lm75"; + reg = <0x48>; + }; + + at24@50 { + compatible = "atmel,24c01"; + pagesize = <8>; + reg = <0x50>; + }; + + i2c-mux@70 { + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + }; + + i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <4>; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + + i2c@6 { /* Backplane EEPROM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + eeprom@51 { + compatible = "atmel,24c01"; + pagesize = <8>; + reg = <0x51>; + }; + }; + + i2c@7 { /* Power board EEPROM */ + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + eeprom@51 { + compatible = "atmel,24c01"; + pagesize = <8>; + reg = <0x51>; + }; + }; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <100000>; + + at24@50 { + compatible = "atmel,24c02"; + pagesize = <8>; + reg = <0x50>; + }; +}; + +&qspi { + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,n25q128", "jedec,spi-nor"; + reg = <0>; /* chip select */ + spi-max-frequency = <100000000>; + m25p,fast-read; + + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; + + flash@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "micron,mt25qu02g", "jedec,spi-nor"; + reg = <1>; /* chip select */ + spi-max-frequency = <100000000>; + m25p,fast-read; + + cdns,page-size = <256>; + cdns,block-size = <16>; + cdns,read-delay = <4>; + cdns,tshsl-ns = <50>; + cdns,tsd2d-ns = <50>; + cdns,tchsh-ns = <4>; + cdns,tslch-ns = <4>; + }; +}; + +&usb0 { + dr_mode = "host"; + status = "okay"; +}; + +&usb1 { + dr_mode = "peripheral"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts b/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts new file mode 100644 index 000000000000..845ab2cc5ce6 --- /dev/null +++ b/arch/arm/boot/dts/intel/socfpga/socfpga_vt.dts @@ -0,0 +1,77 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2013 Altera Corporation <www.altera.com> + */ + +/dts-v1/; +#include "socfpga.dtsi" + +/ { + model = "Altera SOCFPGA VT"; + compatible = "altr,socfpga-vt", "altr,socfpga"; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + memory@0 { + name = "memory"; + device_type = "memory"; + reg = <0x0 0x40000000>; /* 1 GB */ + }; + + soc { + clkmgr@ffd04000 { + clocks { + osc1 { + clock-frequency = <10000000>; + }; + }; + }; + + mmc@ff704000 { + broken-cd; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + }; + + ethernet@ff700000 { + phy-mode = "gmii"; + status = "okay"; + }; + + timer0@ffc08000 { + clock-frequency = <7000000>; + }; + + timer1@ffc09000 { + clock-frequency = <7000000>; + }; + + timer2@ffd00000 { + clock-frequency = <7000000>; + }; + + timer3@ffd01000 { + clock-frequency = <7000000>; + }; + + serial@ffc02000 { + clock-frequency = <7372800>; + }; + + serial@ffc03000 { + clock-frequency = <7372800>; + }; + + sysmgr@ffd08000 { + cpu1-start-addr = <0xffd08010>; + }; + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "gmii"; +}; |