summaryrefslogtreecommitdiff
path: root/drivers/spi/Kconfig
diff options
context:
space:
mode:
authorMark Brown <broonie@kernel.org>2021-09-27 20:32:13 +0300
committerMark Brown <broonie@kernel.org>2021-09-27 20:32:13 +0300
commit728cb436d4bee8d4f7ad64f014915a4fb6e58c5b (patch)
tree49026c03c45e2462ce4bf310278bad1f450ee471 /drivers/spi/Kconfig
parenteca17cbabd0cd52d32949b5ae27a4b3344e87781 (diff)
parenta16cc807762730a6291762d4bedd7b00624a6426 (diff)
downloadlinux-728cb436d4bee8d4f7ad64f014915a4fb6e58c5b.tar.xz
Merge series "add support for Cadence's XSPI controller" from Parshuram Thombare <pthombar@cadence.com>:
This patch series adds support for Cadence's XSPI controller. It supports 3 work modes. 1. ACMD (auto command) work mode ACMD name is because it uses auto command engine in the controller. It further has 2 modes PIO and CDMA (command DMA). The CDMA work mode is dedicated for high-performance application where very low software overhead is required. In this mode the Command Engine is programmed by the series of linked descriptors stored in system memory. These descriptors provide commands to execute and store status information for finished commands. The PIO mode work mode is dedicated for single operation where constructing a linked list of descriptors would require too much effort. 2. STIG (Software Triggered Instruction Generator) work mode In STIG mode, controller sends low-level instructions to memory. Each instruction is 128-bit width. There is special instruction DataSequence which carries information about data phase. Driver uses Slave DMA interface to transfer data as only this interface can be used in STIG work mode. 3. Direct work mode This work mode allows sending data without invoking any command through the slave interface. Currently only STIG work mode is enabled, remaining work modes will be added later. Changes since v5: 1. Added adjust_op_size to adjust op size according to sdma size. Changes since v4: 1. Changed reg region names and lengths as suggested by Rob. Changes since v3: 1. Removed ACMD PIO mode. 2. Return IRQ_HANDLED only for handled interrupts. 3. DT binding changes. Changes since v2: 1. Removed extra lock around exec_op. 2. Removed PHY parameters setting from the driver, those will be handled by bootstrap pins available in the controller. Changes since v1: 1. Use ACMD PIO work mode for NOR read, program and erase operations, for everything else use STIG(Software Triggered Instruction Generator) work mode. 2. Changes suggested by Lukas. Parshuram Thombare (2): spi: cadence: add dt-bindings documentation for Cadence XSPI controller spi: cadence: add support for Cadence XSPI controller .../devicetree/bindings/spi/cdns,xspi.yaml | 77 +++ drivers/spi/Kconfig | 12 + drivers/spi/Makefile | 1 + drivers/spi/spi-cadence-xspi.c | 640 +++++++++++++++++++++ 4 files changed, 730 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/cdns,xspi.yaml create mode 100644 drivers/spi/spi-cadence-xspi.c -- 2.7.4
Diffstat (limited to 'drivers/spi/Kconfig')
-rw-r--r--drivers/spi/Kconfig12
1 files changed, 12 insertions, 0 deletions
diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index c1c8e15c01a2..596705d24400 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -228,6 +228,18 @@ config SPI_CADENCE_QUADSPI
device with a Cadence QSPI controller and want to access the
Flash as an MTD device.
+config SPI_CADENCE_XSPI
+ tristate "Cadence XSPI controller"
+ depends on (OF || COMPILE_TEST) && HAS_IOMEM
+ depends on SPI_MEM
+ help
+ Enable support for the Cadence XSPI Flash controller.
+
+ Cadence XSPI is a specialized controller for connecting an SPI
+ Flash over upto 8bit wide bus. Enable this option if you have a
+ device with a Cadence XSPI controller and want to access the
+ Flash as an MTD device.
+
config SPI_CLPS711X
tristate "CLPS711X host SPI controller"
depends on ARCH_CLPS711X || COMPILE_TEST