summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
authorStefan Agner <stefan@agner.ch>2018-07-04 18:07:45 +0300
committerUlf Hansson <ulf.hansson@linaro.org>2018-07-09 12:17:47 +0300
commit92748beac07c471d995fbec642b63572dc01b3dc (patch)
treed8aae251186eda610d2d01ce70894f105672393e /drivers
parentb8ba3578752b7aae5b6f8bd235873ea112969ff9 (diff)
downloadlinux-92748beac07c471d995fbec642b63572dc01b3dc.tar.xz
mmc: sdhci-esdhc-imx: allow 1.8V modes without 100/200MHz pinctrl states
If pinctrl nodes for 100/200MHz are missing, the controller should not select any mode which need signal frequencies 100MHz or higher. To prevent such speed modes the driver currently uses the quirk flag SDHCI_QUIRK2_NO_1_8_V. This works nicely for SD cards since 1.8V signaling is required for all faster modes and slower modes use 3.3V signaling only. However, there are eMMC modes which use 1.8V signaling and run below 100MHz, e.g. DDR52 at 1.8V. With using SDHCI_QUIRK2_NO_1_8_V this mode is prevented. When using a fixed 1.8V regulator as vqmmc-supply the stack has no valid mode to use. In this tenuous situation the kernel continuously prints voltage switching errors: mmc1: Switching to 3.3V signalling voltage failed Avoid using SDHCI_QUIRK2_NO_1_8_V and prevent faster modes by altering the SDHCI capability register. With that the stack is able to select 1.8V modes even if no faster pinctrl states are available: # cat /sys/kernel/debug/mmc1/ios ... timing spec: 8 (mmc DDR52) signal voltage: 1 (1.80 V) ... Link: http://lkml.kernel.org/r/20180628081331.13051-1-stefan@agner.ch Signed-off-by: Stefan Agner <stefan@agner.ch> Fixes: ad93220de7da ("mmc: sdhci-esdhc-imx: change pinctrl state according to uhs mode") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Diffstat (limited to 'drivers')
-rw-r--r--drivers/mmc/host/sdhci-esdhc-imx.c21
1 files changed, 9 insertions, 12 deletions
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index d6aef70d34fa..4eb3d29ecde1 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -312,6 +312,15 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
val |= SDHCI_SUPPORT_HS400;
+
+ /*
+ * Do not advertise faster UHS modes if there are no
+ * pinctrl states for 100MHz/200MHz.
+ */
+ if (IS_ERR_OR_NULL(imx_data->pins_100mhz) ||
+ IS_ERR_OR_NULL(imx_data->pins_200mhz))
+ val &= ~(SDHCI_SUPPORT_SDR50 | SDHCI_SUPPORT_DDR50
+ | SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_HS400);
}
}
@@ -1158,18 +1167,6 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
ESDHC_PINCTRL_STATE_100MHZ);
imx_data->pins_200mhz = pinctrl_lookup_state(imx_data->pinctrl,
ESDHC_PINCTRL_STATE_200MHZ);
- if (IS_ERR(imx_data->pins_100mhz) ||
- IS_ERR(imx_data->pins_200mhz)) {
- dev_warn(mmc_dev(host->mmc),
- "could not get ultra high speed state, work on normal mode\n");
- /*
- * fall back to not supporting uhs by specifying no
- * 1.8v quirk
- */
- host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
- }
- } else {
- host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
}
/* call to generic mmc_of_parse to support additional capabilities */