summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--arch/arm/Kconfig.debug16
-rw-r--r--arch/arm/mach-bcm/Kconfig3
-rw-r--r--arch/arm/mach-bcm/Makefile2
-rw-r--r--arch/arm/mach-bcm/brcmstb.h19
-rw-r--r--arch/arm/mach-bcm/headsmp-brcmstb.S33
-rw-r--r--arch/arm/mach-bcm/platsmp-brcmstb.c329
-rw-r--r--drivers/bus/brcmstb_gisb.c47
7 files changed, 439 insertions, 10 deletions
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 03dc4c1a8736..6a4ee008b092 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -139,6 +139,17 @@ choice
Say Y here if you want kernel low-level debugging support
on Marvell Berlin SoC based platforms.
+ config DEBUG_BRCMSTB_UART
+ bool "Use BRCMSTB UART for low-level debug"
+ depends on ARCH_BRCMSTB
+ select DEBUG_UART_8250
+ help
+ Say Y here if you want the debug print routines to direct
+ their output to the first serial port on these devices.
+
+ If you have a Broadcom STB chip and would like early print
+ messages to appear over the UART, select this option.
+
config DEBUG_CLPS711X_UART1
bool "Kernel low-level debugging messages via UART1"
depends on ARCH_CLPS711X
@@ -1153,6 +1164,7 @@ config DEBUG_UART_PHYS
default 0xe0000000 if ARCH_SPEAR13XX
default 0xe4007000 if DEBUG_HIP04_UART
default 0xf0000be0 if ARCH_EBSA110
+ default 0xf040ab00 if DEBUG_BRCMSTB_UART
default 0xf1012000 if DEBUG_MVEBU_UART_ALTERNATE
default 0xf1012000 if ARCH_DOVE || ARCH_MV78XX0 || \
ARCH_ORION5X
@@ -1204,6 +1216,7 @@ config DEBUG_UART_VIRT
default 0xfb002000 if DEBUG_CNS3XXX
default 0xfb009000 if DEBUG_REALVIEW_STD_PORT
default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
+ default 0xfc40ab00 if DEBUG_BRCMSTB_UART
default 0xfcfe8600 if DEBUG_UART_BCM63XX
default 0xfd000000 if ARCH_SPEAR3XX || ARCH_SPEAR6XX
default 0xfd000000 if ARCH_SPEAR13XX
@@ -1260,7 +1273,8 @@ config DEBUG_UART_8250_WORD
ARCH_KEYSTONE || \
DEBUG_DAVINCI_DMx_UART0 || DEBUG_DAVINCI_DA8XX_UART1 || \
DEBUG_DAVINCI_DA8XX_UART2 || \
- DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2
+ DEBUG_BCM_KONA_UART || DEBUG_RK32_UART2 || \
+ DEBUG_BRCMSTB_UART
config DEBUG_UART_8250_FLOW_CONTROL
bool "Enable flow control for 8250 UART"
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index 2abad742516d..9625dddb5cd3 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -118,10 +118,7 @@ config ARCH_BCM_63XX
config ARCH_BRCMSTB
bool "Broadcom BCM7XXX based boards" if ARCH_MULTI_V7
- depends on MMU
select ARM_GIC
- select MIGHT_HAVE_PCI
- select HAVE_SMP
select HAVE_ARM_ARCH_TIMER
select BRCMSTB_GISB_ARB
select BRCMSTB_L2_IRQ
diff --git a/arch/arm/mach-bcm/Makefile b/arch/arm/mach-bcm/Makefile
index 300ae4b79ae6..6710ea321220 100644
--- a/arch/arm/mach-bcm/Makefile
+++ b/arch/arm/mach-bcm/Makefile
@@ -38,5 +38,7 @@ obj-$(CONFIG_ARCH_BCM_5301X) += bcm_5301x.o
obj-$(CONFIG_ARCH_BCM_63XX) := bcm63xx.o
ifeq ($(CONFIG_ARCH_BRCMSTB),y)
+CFLAGS_platsmp-brcmstb.o += -march=armv7-a
obj-y += brcmstb.o
+obj-$(CONFIG_SMP) += headsmp-brcmstb.o platsmp-brcmstb.o
endif
diff --git a/arch/arm/mach-bcm/brcmstb.h b/arch/arm/mach-bcm/brcmstb.h
new file mode 100644
index 000000000000..ec0c3d112b36
--- /dev/null
+++ b/arch/arm/mach-bcm/brcmstb.h
@@ -0,0 +1,19 @@
+/*
+ * Copyright (C) 2013-2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __BRCMSTB_H__
+#define __BRCMSTB_H__
+
+void brcmstb_secondary_startup(void);
+
+#endif /* __BRCMSTB_H__ */
diff --git a/arch/arm/mach-bcm/headsmp-brcmstb.S b/arch/arm/mach-bcm/headsmp-brcmstb.S
new file mode 100644
index 000000000000..199c1ea58248
--- /dev/null
+++ b/arch/arm/mach-bcm/headsmp-brcmstb.S
@@ -0,0 +1,33 @@
+/*
+ * SMP boot code for secondary CPUs
+ * Based on arch/arm/mach-tegra/headsmp.S
+ *
+ * Copyright (C) 2010 NVIDIA, Inc.
+ * Copyright (C) 2013-2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <asm/assembler.h>
+#include <linux/linkage.h>
+#include <linux/init.h>
+
+ .section ".text.head", "ax"
+
+ENTRY(brcmstb_secondary_startup)
+ /*
+ * Ensure CPU is in a sane state by disabling all IRQs and switching
+ * into SVC mode.
+ */
+ setmode PSR_I_BIT | PSR_F_BIT | SVC_MODE, r0
+
+ bl v7_invalidate_l1
+ b secondary_startup
+ENDPROC(brcmstb_secondary_startup)
diff --git a/arch/arm/mach-bcm/platsmp-brcmstb.c b/arch/arm/mach-bcm/platsmp-brcmstb.c
new file mode 100644
index 000000000000..31c87a284a34
--- /dev/null
+++ b/arch/arm/mach-bcm/platsmp-brcmstb.c
@@ -0,0 +1,329 @@
+/*
+ * Broadcom STB CPU SMP and hotplug support for ARM
+ *
+ * Copyright (C) 2013-2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/printk.h>
+#include <linux/regmap.h>
+#include <linux/smp.h>
+#include <linux/mfd/syscon.h>
+
+#include <asm/cacheflush.h>
+#include <asm/cp15.h>
+#include <asm/mach-types.h>
+#include <asm/smp_plat.h>
+
+#include "brcmstb.h"
+
+enum {
+ ZONE_MAN_CLKEN_MASK = BIT(0),
+ ZONE_MAN_RESET_CNTL_MASK = BIT(1),
+ ZONE_MAN_MEM_PWR_MASK = BIT(4),
+ ZONE_RESERVED_1_MASK = BIT(5),
+ ZONE_MAN_ISO_CNTL_MASK = BIT(6),
+ ZONE_MANUAL_CONTROL_MASK = BIT(7),
+ ZONE_PWR_DN_REQ_MASK = BIT(9),
+ ZONE_PWR_UP_REQ_MASK = BIT(10),
+ ZONE_BLK_RST_ASSERT_MASK = BIT(12),
+ ZONE_PWR_OFF_STATE_MASK = BIT(25),
+ ZONE_PWR_ON_STATE_MASK = BIT(26),
+ ZONE_DPG_PWR_STATE_MASK = BIT(28),
+ ZONE_MEM_PWR_STATE_MASK = BIT(29),
+ ZONE_RESET_STATE_MASK = BIT(31),
+ CPU0_PWR_ZONE_CTRL_REG = 1,
+ CPU_RESET_CONFIG_REG = 2,
+};
+
+static void __iomem *cpubiuctrl_block;
+static void __iomem *hif_cont_block;
+static u32 cpu0_pwr_zone_ctrl_reg;
+static u32 cpu_rst_cfg_reg;
+static u32 hif_cont_reg;
+
+#ifdef CONFIG_HOTPLUG_CPU
+/*
+ * We must quiesce a dying CPU before it can be killed by the boot CPU. Because
+ * one or more cache may be disabled, we must flush to ensure coherency. We
+ * cannot use traditionl completion structures or spinlocks as they rely on
+ * coherency.
+ */
+static DEFINE_PER_CPU_ALIGNED(int, per_cpu_sw_state);
+
+static int per_cpu_sw_state_rd(u32 cpu)
+{
+ sync_cache_r(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
+ return per_cpu(per_cpu_sw_state, cpu);
+}
+
+static void per_cpu_sw_state_wr(u32 cpu, int val)
+{
+ dmb();
+ per_cpu(per_cpu_sw_state, cpu) = val;
+ sync_cache_w(SHIFT_PERCPU_PTR(&per_cpu_sw_state, per_cpu_offset(cpu)));
+}
+#else
+static inline void per_cpu_sw_state_wr(u32 cpu, int val) { }
+#endif
+
+static void __iomem *pwr_ctrl_get_base(u32 cpu)
+{
+ void __iomem *base = cpubiuctrl_block + cpu0_pwr_zone_ctrl_reg;
+ base += (cpu_logical_map(cpu) * 4);
+ return base;
+}
+
+static u32 pwr_ctrl_rd(u32 cpu)
+{
+ void __iomem *base = pwr_ctrl_get_base(cpu);
+ return readl_relaxed(base);
+}
+
+static void pwr_ctrl_wr(u32 cpu, u32 val)
+{
+ void __iomem *base = pwr_ctrl_get_base(cpu);
+ writel(val, base);
+}
+
+static void cpu_rst_cfg_set(u32 cpu, int set)
+{
+ u32 val;
+ val = readl_relaxed(cpubiuctrl_block + cpu_rst_cfg_reg);
+ if (set)
+ val |= BIT(cpu_logical_map(cpu));
+ else
+ val &= ~BIT(cpu_logical_map(cpu));
+ writel_relaxed(val, cpubiuctrl_block + cpu_rst_cfg_reg);
+}
+
+static void cpu_set_boot_addr(u32 cpu, unsigned long boot_addr)
+{
+ const int reg_ofs = cpu_logical_map(cpu) * 8;
+ writel_relaxed(0, hif_cont_block + hif_cont_reg + reg_ofs);
+ writel_relaxed(boot_addr, hif_cont_block + hif_cont_reg + 4 + reg_ofs);
+}
+
+static void brcmstb_cpu_boot(u32 cpu)
+{
+ /* Mark this CPU as "up" */
+ per_cpu_sw_state_wr(cpu, 1);
+
+ /*
+ * Set the reset vector to point to the secondary_startup
+ * routine
+ */
+ cpu_set_boot_addr(cpu, virt_to_phys(brcmstb_secondary_startup));
+
+ /* Unhalt the cpu */
+ cpu_rst_cfg_set(cpu, 0);
+}
+
+static void brcmstb_cpu_power_on(u32 cpu)
+{
+ /*
+ * The secondary cores power was cut, so we must go through
+ * power-on initialization.
+ */
+ u32 tmp;
+
+ /* Request zone power up */
+ pwr_ctrl_wr(cpu, ZONE_PWR_UP_REQ_MASK);
+
+ /* Wait for the power up FSM to complete */
+ do {
+ tmp = pwr_ctrl_rd(cpu);
+ } while (!(tmp & ZONE_PWR_ON_STATE_MASK));
+}
+
+static int brcmstb_cpu_get_power_state(u32 cpu)
+{
+ int tmp = pwr_ctrl_rd(cpu);
+ return (tmp & ZONE_RESET_STATE_MASK) ? 0 : 1;
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+static void brcmstb_cpu_die(u32 cpu)
+{
+ v7_exit_coherency_flush(all);
+
+ per_cpu_sw_state_wr(cpu, 0);
+
+ /* Sit and wait to die */
+ wfi();
+
+ /* We should never get here... */
+ while (1)
+ ;
+}
+
+static int brcmstb_cpu_kill(u32 cpu)
+{
+ u32 tmp;
+
+ while (per_cpu_sw_state_rd(cpu))
+ ;
+
+ /* Program zone reset */
+ pwr_ctrl_wr(cpu, ZONE_RESET_STATE_MASK | ZONE_BLK_RST_ASSERT_MASK |
+ ZONE_PWR_DN_REQ_MASK);
+
+ /* Verify zone reset */
+ tmp = pwr_ctrl_rd(cpu);
+ if (!(tmp & ZONE_RESET_STATE_MASK))
+ pr_err("%s: Zone reset bit for CPU %d not asserted!\n",
+ __func__, cpu);
+
+ /* Wait for power down */
+ do {
+ tmp = pwr_ctrl_rd(cpu);
+ } while (!(tmp & ZONE_PWR_OFF_STATE_MASK));
+
+ /* Flush pipeline before resetting CPU */
+ mb();
+
+ /* Assert reset on the CPU */
+ cpu_rst_cfg_set(cpu, 1);
+
+ return 1;
+}
+
+#endif /* CONFIG_HOTPLUG_CPU */
+
+static int __init setup_hifcpubiuctrl_regs(struct device_node *np)
+{
+ int rc = 0;
+ char *name;
+ struct device_node *syscon_np = NULL;
+
+ name = "syscon-cpu";
+
+ syscon_np = of_parse_phandle(np, name, 0);
+ if (!syscon_np) {
+ pr_err("can't find phandle %s\n", name);
+ rc = -EINVAL;
+ goto cleanup;
+ }
+
+ cpubiuctrl_block = of_iomap(syscon_np, 0);
+ if (!cpubiuctrl_block) {
+ pr_err("iomap failed for cpubiuctrl_block\n");
+ rc = -EINVAL;
+ goto cleanup;
+ }
+
+ rc = of_property_read_u32_index(np, name, CPU0_PWR_ZONE_CTRL_REG,
+ &cpu0_pwr_zone_ctrl_reg);
+ if (rc) {
+ pr_err("failed to read 1st entry from %s property (%d)\n", name,
+ rc);
+ rc = -EINVAL;
+ goto cleanup;
+ }
+
+ rc = of_property_read_u32_index(np, name, CPU_RESET_CONFIG_REG,
+ &cpu_rst_cfg_reg);
+ if (rc) {
+ pr_err("failed to read 2nd entry from %s property (%d)\n", name,
+ rc);
+ rc = -EINVAL;
+ goto cleanup;
+ }
+
+cleanup:
+ of_node_put(syscon_np);
+ return rc;
+}
+
+static int __init setup_hifcont_regs(struct device_node *np)
+{
+ int rc = 0;
+ char *name;
+ struct device_node *syscon_np = NULL;
+
+ name = "syscon-cont";
+
+ syscon_np = of_parse_phandle(np, name, 0);
+ if (!syscon_np) {
+ pr_err("can't find phandle %s\n", name);
+ rc = -EINVAL;
+ goto cleanup;
+ }
+
+ hif_cont_block = of_iomap(syscon_np, 0);
+ if (!hif_cont_block) {
+ pr_err("iomap failed for hif_cont_block\n");
+ rc = -EINVAL;
+ goto cleanup;
+ }
+
+ /* Offset is at top of hif_cont_block */
+ hif_cont_reg = 0;
+
+cleanup:
+ of_node_put(syscon_np);
+ return rc;
+}
+
+static void __init brcmstb_cpu_ctrl_setup(unsigned int max_cpus)
+{
+ int rc;
+ struct device_node *np;
+ char *name;
+
+ name = "brcm,brcmstb-smpboot";
+ np = of_find_compatible_node(NULL, NULL, name);
+ if (!np) {
+ pr_err("can't find compatible node %s\n", name);
+ return;
+ }
+
+ rc = setup_hifcpubiuctrl_regs(np);
+ if (rc)
+ return;
+
+ rc = setup_hifcont_regs(np);
+ if (rc)
+ return;
+}
+
+static int brcmstb_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ /* Missing the brcm,brcmstb-smpboot DT node? */
+ if (!cpubiuctrl_block || !hif_cont_block)
+ return -ENODEV;
+
+ /* Bring up power to the core if necessary */
+ if (brcmstb_cpu_get_power_state(cpu) == 0)
+ brcmstb_cpu_power_on(cpu);
+
+ brcmstb_cpu_boot(cpu);
+
+ return 0;
+}
+
+static struct smp_operations brcmstb_smp_ops __initdata = {
+ .smp_prepare_cpus = brcmstb_cpu_ctrl_setup,
+ .smp_boot_secondary = brcmstb_boot_secondary,
+#ifdef CONFIG_HOTPLUG_CPU
+ .cpu_kill = brcmstb_cpu_kill,
+ .cpu_die = brcmstb_cpu_die,
+#endif
+};
+
+CPU_METHOD_OF_DECLARE(brcmstb_smp, "brcm,brahma-b15", &brcmstb_smp_ops);
diff --git a/drivers/bus/brcmstb_gisb.c b/drivers/bus/brcmstb_gisb.c
index bfd40f11e921..46de8dc39eb4 100644
--- a/drivers/bus/brcmstb_gisb.c
+++ b/drivers/bus/brcmstb_gisb.c
@@ -23,6 +23,7 @@
#include <linux/list.h>
#include <linux/of.h>
#include <linux/bitops.h>
+#include <linux/pm.h>
#ifdef CONFIG_ARM
#include <asm/bug.h>
@@ -94,6 +95,7 @@ struct brcmstb_gisb_arb_device {
struct list_head next;
u32 valid_mask;
const char *master_names[sizeof(u32) * BITS_PER_BYTE];
+ u32 saved_timeout;
};
static LIST_HEAD(brcmstb_gisb_arb_device_list);
@@ -226,12 +228,6 @@ static int brcmstb_bus_error_handler(unsigned long addr, unsigned int fsr,
return ret;
}
-
-void __init brcmstb_hook_fault_code(void)
-{
- hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
- "imprecise external abort");
-}
#endif
static irqreturn_t brcmstb_gisb_timeout_handler(int irq, void *dev_id)
@@ -346,17 +342,56 @@ static int __init brcmstb_gisb_arb_probe(struct platform_device *pdev)
list_add_tail(&gdev->next, &brcmstb_gisb_arb_device_list);
+#ifdef CONFIG_ARM
+ hook_fault_code(22, brcmstb_bus_error_handler, SIGBUS, 0,
+ "imprecise external abort");
+#endif
+
dev_info(&pdev->dev, "registered mem: %p, irqs: %d, %d\n",
gdev->base, timeout_irq, tea_irq);
return 0;
}
+#ifdef CONFIG_PM_SLEEP
+static int brcmstb_gisb_arb_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct brcmstb_gisb_arb_device *gdev = platform_get_drvdata(pdev);
+
+ gdev->saved_timeout = gisb_read(gdev, ARB_TIMER);
+
+ return 0;
+}
+
+/* Make sure we provide the same timeout value that was configured before, and
+ * do this before the GISB timeout interrupt handler has any chance to run.
+ */
+static int brcmstb_gisb_arb_resume_noirq(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct brcmstb_gisb_arb_device *gdev = platform_get_drvdata(pdev);
+
+ gisb_write(gdev, gdev->saved_timeout, ARB_TIMER);
+
+ return 0;
+}
+#else
+#define brcmstb_gisb_arb_suspend NULL
+#define brcmstb_gisb_arb_resume_noirq NULL
+#endif
+
+static const struct dev_pm_ops brcmstb_gisb_arb_pm_ops = {
+ .suspend = brcmstb_gisb_arb_suspend,
+ .resume_noirq = brcmstb_gisb_arb_resume_noirq,
+};
+
static struct platform_driver brcmstb_gisb_arb_driver = {
.driver = {
.name = "brcm-gisb-arb",
.owner = THIS_MODULE,
.of_match_table = brcmstb_gisb_arb_of_match,
+ .pm = &brcmstb_gisb_arb_pm_ops,
},
};