summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Documentation/i2c/slave-testunit-backend.rst23
-rw-r--r--drivers/i2c/i2c-slave-testunit.c12
2 files changed, 31 insertions, 4 deletions
diff --git a/Documentation/i2c/slave-testunit-backend.rst b/Documentation/i2c/slave-testunit-backend.rst
index 2c38e64f0bac..ecfc2abec32d 100644
--- a/Documentation/i2c/slave-testunit-backend.rst
+++ b/Documentation/i2c/slave-testunit-backend.rst
@@ -22,8 +22,9 @@ Instantiating the device is regular. Example for bus 0, address 0x30:
After that, you will have a write-only device listening. Reads will just return
an 8-bit version number of the testunit. When writing, the device consists of 4
-8-bit registers and all must be written to start a testcase, i.e. you must
-always write 4 bytes to the device. The registers are:
+8-bit registers and, except for some "partial" commands, all registers must be
+written to start a testcase, i.e. you usually write 4 bytes to the device. The
+registers are:
0x00 CMD - which test to trigger
0x01 DATAL - configuration byte 1 for the test
@@ -67,3 +68,21 @@ status word is currently ignored in the Linux Kernel. Example to send a
notification after 10ms:
# i2cset -y 0 0x30 0x02 0x42 0x64 0x01 i
+
+0x03 SMBUS_BLOCK_PROC_CALL (partial command)
+ DATAL - must be '1', i.e. one further byte will be written
+ DATAH - number of bytes to be sent back
+ DELAY - not applicable, partial command!
+
+This test will respond to a block process call as defined by the SMBus
+specification. The one data byte written specifies how many bytes will be sent
+back in the following read transfer. Note that in this read transfer, the
+testunit will prefix the length of the bytes to follow. So, if your host bus
+driver emulates SMBus calls like the majority does, it needs to support the
+I2C_M_RECV_LEN flag of an i2c_msg. This is a good testcase for it. The returned
+data consists of the length first, and then of an array of bytes from length-1
+to 0. Here is an example which emulates i2c_smbus_block_process_call() using
+i2ctransfer (you need i2c-tools v4.2 or later):
+
+# i2ctransfer -y 0 w3@0x30 0x03 0x01 0x10 r?
+0x10 0x0f 0x0e 0x0d 0x0c 0x0b 0x0a 0x09 0x08 0x07 0x06 0x05 0x04 0x03 0x02 0x01 0x00
diff --git a/drivers/i2c/i2c-slave-testunit.c b/drivers/i2c/i2c-slave-testunit.c
index c288102de324..56dae08dfd48 100644
--- a/drivers/i2c/i2c-slave-testunit.c
+++ b/drivers/i2c/i2c-slave-testunit.c
@@ -19,6 +19,7 @@
enum testunit_cmds {
TU_CMD_READ_BYTES = 1, /* save 0 for ABORT, RESET or similar */
TU_CMD_HOST_NOTIFY,
+ TU_CMD_SMBUS_BLOCK_PROC_CALL,
TU_NUM_CMDS
};
@@ -88,6 +89,8 @@ static int i2c_slave_testunit_slave_cb(struct i2c_client *client,
enum i2c_slave_event event, u8 *val)
{
struct testunit_data *tu = i2c_get_clientdata(client);
+ bool is_proc_call = tu->reg_idx == 3 && tu->regs[TU_REG_DATAL] == 1 &&
+ tu->regs[TU_REG_CMD] == TU_CMD_SMBUS_BLOCK_PROC_CALL;
int ret = 0;
switch (event) {
@@ -118,12 +121,17 @@ static int i2c_slave_testunit_slave_cb(struct i2c_client *client,
fallthrough;
case I2C_SLAVE_WRITE_REQUESTED:
+ memset(tu->regs, 0, TU_NUM_REGS);
tu->reg_idx = 0;
break;
- case I2C_SLAVE_READ_REQUESTED:
case I2C_SLAVE_READ_PROCESSED:
- *val = TU_CUR_VERSION;
+ if (is_proc_call && tu->regs[TU_REG_DATAH])
+ tu->regs[TU_REG_DATAH]--;
+ fallthrough;
+
+ case I2C_SLAVE_READ_REQUESTED:
+ *val = is_proc_call ? tu->regs[TU_REG_DATAH] : TU_CUR_VERSION;
break;
}