diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/bridge')
5 files changed, 288 insertions, 22 deletions
diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt index a6b2b2b8f3d9..d3c2a4914ea2 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7123.txt @@ -1,5 +1,5 @@ -Analog Device ADV7123 Video DAC -------------------------------- +Analog Devices ADV7123 Video DAC +-------------------------------- The ADV7123 is a digital-to-analog converter that outputs VGA signals from a parallel video input. diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 2c887536258c..659523f538bf 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -1,10 +1,10 @@ -Analog Device ADV7511(W)/13/33 HDMI Encoders ------------------------------------------ +Analog Devices ADV7511(W)/13/33/35 HDMI Encoders +------------------------------------------------ -The ADV7511, ADV7511W, ADV7513 and ADV7533 are HDMI audio and video transmitters -compatible with HDMI 1.4 and DVI 1.0. They support color space conversion, -S/PDIF, CEC and HDCP. ADV7533 supports the DSI interface for input pixels, while -the others support RGB interface. +The ADV7511, ADV7511W, ADV7513, ADV7533 and ADV7535 are HDMI audio and video +transmitters compatible with HDMI 1.4 and DVI 1.0. They support color space +conversion, S/PDIF, CEC and HDCP. ADV7533/5 supports the DSI interface for input +pixels, while the others support RGB interface. Required properties: @@ -13,6 +13,7 @@ Required properties: "adi,adv7511w" "adi,adv7513" "adi,adv7533" + "adi,adv7535" - reg: I2C slave addresses The ADV7511 internal registers are split into four pages exposed through @@ -52,14 +53,14 @@ The following input format properties are required except in "rgb 1x" and - bgvdd-supply: A 1.8V supply that powers up the BGVDD pin. This is needed only for ADV7511. -The following properties are required for ADV7533: +The following properties are required for ADV7533 and ADV7535: - adi,dsi-lanes: Number of DSI data lanes connected to the DSI host. It should be one of 1, 2, 3 or 4. - a2vdd-supply: 1.8V supply that powers up the A2VDD pin on the chip. - v3p3-supply: A 3.3V supply that powers up the V3P3 pin on the chip. - v1p2-supply: A supply that powers up the V1P2 pin on the chip. It can be - either 1.2V or 1.8V. + either 1.2V or 1.8V for ADV7533 but only 1.8V for ADV7535. Optional properties: @@ -71,9 +72,9 @@ Optional properties: - adi,embedded-sync: The input uses synchronization signals embedded in the data stream (similar to BT.656). Defaults to separate H/V synchronization signals. -- adi,disable-timing-generator: Only for ADV7533. Disables the internal timing - generator. The chip will rely on the sync signals in the DSI data lanes, - rather than generate its own timings for HDMI output. +- adi,disable-timing-generator: Only for ADV7533 and ADV7535. Disables the + internal timing generator. The chip will rely on the sync signals in the + DSI data lanes, rather than generate its own timings for HDMI output. - clocks: from common clock binding: reference to the CEC clock. - clock-names: from common clock binding: must be "cec". - reg-names : Names of maps with programmable addresses. @@ -85,7 +86,7 @@ Required nodes: The ADV7511 has two video ports. Their connections are modelled using the OF graph bindings specified in Documentation/devicetree/bindings/graph.txt. -- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533, the +- Video port 0 for the RGB, YUV or DSI input. In the case of ADV7533/5, the remote endpoint phandle should be a reference to a valid mipi_dsi_host device node. - Video port 1 for the HDMI output diff --git a/Documentation/devicetree/bindings/display/bridge/anx6345.yaml b/Documentation/devicetree/bindings/display/bridge/anx6345.yaml index 6d72b3d11fbc..c21103869923 100644 --- a/Documentation/devicetree/bindings/display/bridge/anx6345.yaml +++ b/Documentation/devicetree/bindings/display/bridge/anx6345.yaml @@ -79,21 +79,15 @@ examples: #size-cells = <0>; anx6345_in: port@0 { - #address-cells = <1>; - #size-cells = <0>; reg = <0>; - anx6345_in_tcon0: endpoint@0 { - reg = <0>; + anx6345_in_tcon0: endpoint { remote-endpoint = <&tcon0_out_anx6345>; }; }; anx6345_out: port@1 { - #address-cells = <1>; - #size-cells = <0>; reg = <1>; - anx6345_out_panel: endpoint@0 { - reg = <0>; + anx6345_out_panel: endpoint { remote-endpoint = <&panel_in_edp>; }; }; diff --git a/Documentation/devicetree/bindings/display/bridge/ps8640.yaml b/Documentation/devicetree/bindings/display/bridge/ps8640.yaml new file mode 100644 index 000000000000..5dff93641bea --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/ps8640.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/ps8640.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MIPI DSI to eDP Video Format Converter Device Tree Bindings + +maintainers: + - Nicolas Boichat <drinkcat@chromium.org> + - Enric Balletbo i Serra <enric.balletbo@collabora.com> + +description: | + The PS8640 is a low power MIPI-to-eDP video format converter supporting + mobile devices with embedded panel resolutions up to 2048 x 1536. The + device accepts a single channel of MIPI DSI v1.1, with up to four lanes + plus clock, at a transmission rate up to 1.5Gbit/sec per lane. The + device outputs eDP v1.4, one or two lanes, at a link rate of up to + 3.24Gbit/sec per lane. + +properties: + compatible: + const: parade,ps8640 + + reg: + maxItems: 1 + description: Base I2C address of the device. + + powerdown-gpios: + maxItems: 1 + description: GPIO connected to active low powerdown. + + reset-gpios: + maxItems: 1 + description: GPIO connected to active low reset. + + vdd12-supply: + maxItems: 1 + description: Regulator for 1.2V digital core power. + + vdd33-supply: + maxItems: 1 + description: Regulator for 3.3V digital core power. + + ports: + type: object + description: + A node containing DSI input & output port nodes with endpoint + definitions as documented in + Documentation/devicetree/bindings/media/video-interfaces.txt + Documentation/devicetree/bindings/graph.txt + properties: + port@0: + type: object + description: | + Video port for DSI input + + port@1: + type: object + description: | + Video port for eDP output (panel or connector). + + required: + - port@0 + +required: + - compatible + - reg + - powerdown-gpios + - reset-gpios + - vdd12-supply + - vdd33-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + ps8640: edp-bridge@18 { + compatible = "parade,ps8640"; + reg = <0x18>; + powerdown-gpios = <&pio 116 GPIO_ACTIVE_LOW>; + reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>; + vdd12-supply = <&ps8640_fixed_1v2>; + vdd33-supply = <&mt6397_vgp2_reg>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + ps8640_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + ps8640_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml new file mode 100644 index 000000000000..c036a75db8f7 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358768.yaml @@ -0,0 +1,159 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358768.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Toschiba TC358768/TC358778 Parallel RGB to MIPI DSI bridge + +maintainers: + - Peter Ujfalusi <peter.ujfalusi@ti.com> + +description: | + The TC358768/TC358778 is bridge device which converts RGB to DSI. + +properties: + compatible: + enum: + - toshiba,tc358768 + - toshiba,tc358778 + + reg: + maxItems: 1 + description: base I2C address of the device + + reset-gpios: + maxItems: 1 + description: GPIO connected to active low RESX pin + + vddc-supply: + description: Regulator for 1.2V internal core power. + + vddmipi-supply: + description: Regulator for 1.2V for the MIPI. + + vddio-supply: + description: Regulator for 1.8V - 3.3V IO power. + + clocks: + maxItems: 1 + + clock-names: + const: refclk + + ports: + type: object + + properties: + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + port@0: + type: object + additionalProperties: false + + description: | + Video port for RGB input + + properties: + reg: + const: 0 + + patternProperties: + endpoint: + type: object + additionalProperties: false + + properties: + data-lines: + enum: [ 16, 18, 24 ] + + remote-endpoint: true + + required: + - reg + + port@1: + type: object + additionalProperties: false + + description: | + Video port for DSI output (panel or connector). + + properties: + reg: + const: 1 + + patternProperties: + endpoint: + type: object + additionalProperties: false + + properties: + remote-endpoint: true + + required: + - reg + + required: + - "#address-cells" + - "#size-cells" + - port@0 + - port@1 + +required: + - compatible + - reg + - vddc-supply + - vddmipi-supply + - vddio-supply + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + i2c1 { + #address-cells = <1>; + #size-cells = <0>; + + dsi_bridge: dsi-bridge@e { + compatible = "toshiba,tc358768"; + reg = <0xe>; + + clocks = <&tc358768_refclk>; + clock-names = "refclk"; + + reset-gpios = <&pcf_display_board 0 GPIO_ACTIVE_LOW>; + + vddc-supply = <&v1_2d>; + vddmipi-supply = <&v1_2d>; + vddio-supply = <&v3_3d>; + + dsi_bridge_ports: ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + rgb_in: endpoint { + remote-endpoint = <&dpi_out>; + data-lines = <24>; + }; + }; + + port@1 { + reg = <1>; + dsi_out: endpoint { + remote-endpoint = <&lcd_in>; + }; + }; + }; + }; + }; + |