diff options
Diffstat (limited to 'Documentation/devicetree/bindings/gpu')
4 files changed, 155 insertions, 3 deletions
diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt new file mode 100644 index 000000000000..b8be9dbc68b4 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/arm,mali-bifrost.txt @@ -0,0 +1,92 @@ +ARM Mali Bifrost GPU +==================== + +Required properties: + +- compatible : + * Since Mali Bifrost GPU model/revision is fully discoverable by reading + some determined registers, must contain the following: + + "arm,mali-bifrost" + * which must be preceded by one of the following vendor specifics: + + "amlogic,meson-g12a-mali" + +- reg : Physical base address of the device and length of the register area. + +- interrupts : Contains the three IRQ lines required by Mali Bifrost devices, + in the following defined order. + +- interrupt-names : Contains the names of IRQ resources in this exact defined + order: "job", "mmu", "gpu". + +Optional properties: + +- clocks : Phandle to clock for the Mali Bifrost device. + +- mali-supply : Phandle to regulator for the Mali device. Refer to + Documentation/devicetree/bindings/regulator/regulator.txt for details. + +- operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt + for details. + +- resets : Phandle of the GPU reset line. + +Vendor-specific bindings +------------------------ + +The Mali GPU is integrated very differently from one SoC to +another. In order to accommodate those differences, you have the option +to specify one more vendor-specific compatible, among: + +- "amlogic,meson-g12a-mali" + Required properties: + - resets : Should contain phandles of : + + GPU reset line + + GPU APB glue reset line + +Example for a Mali-G31: + +gpu@ffa30000 { + compatible = "amlogic,meson-g12a-mali", "arm,mali-bifrost"; + reg = <0xffe40000 0x10000>; + interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "job", "mmu", "gpu"; + clocks = <&clk CLKID_MALI>; + mali-supply = <&vdd_gpu>; + operating-points-v2 = <&gpu_opp_table>; + resets = <&reset RESET_DVALIN_CAPB3>, <&reset RESET_DVALIN>; +}; + +gpu_opp_table: opp_table0 { + compatible = "operating-points-v2"; + + opp@533000000 { + opp-hz = /bits/ 64 <533000000>; + opp-microvolt = <1250000>; + }; + opp@450000000 { + opp-hz = /bits/ 64 <450000000>; + opp-microvolt = <1150000>; + }; + opp@400000000 { + opp-hz = /bits/ 64 <400000000>; + opp-microvolt = <1125000>; + }; + opp@350000000 { + opp-hz = /bits/ 64 <350000000>; + opp-microvolt = <1075000>; + }; + opp@266000000 { + opp-hz = /bits/ 64 <266000000>; + opp-microvolt = <1025000>; + }; + opp@160000000 { + opp-hz = /bits/ 64 <160000000>; + opp-microvolt = <925000>; + }; + opp@100000000 { + opp-hz = /bits/ 64 <100000000>; + opp-microvolt = <912500>; + }; +}; diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt index 18a2cde2e5f3..1b1a74129141 100644 --- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt +++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt @@ -37,6 +37,20 @@ Optional properties: - operating-points-v2 : Refer to Documentation/devicetree/bindings/opp/opp.txt for details. +- resets : Phandle of the GPU reset line. + +Vendor-specific bindings +------------------------ + +The Mali GPU is integrated very differently from one SoC to +another. In order to accomodate those differences, you have the option +to specify one more vendor-specific compatible, among: + +- "amlogic,meson-gxm-mali" + Required properties: + - resets : Should contain phandles of : + + GPU reset line + + GPU APB glue reset line Example for a Mali-T760: diff --git a/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt b/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt new file mode 100644 index 000000000000..958bdf962339 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/aspeed-gfx.txt @@ -0,0 +1,41 @@ +Device tree configuration for the GFX display device on the ASPEED SoCs + +Required properties: + - compatible + * Must be one of the following: + + aspeed,ast2500-gfx + + aspeed,ast2400-gfx + * In addition, the ASPEED pinctrl bindings require the 'syscon' property to + be present + + - reg: Physical base address and length of the GFX registers + + - interrupts: interrupt number for the GFX device + + - clocks: clock number used to generate the pixel clock + + - resets: reset line that must be released to use the GFX device + + - memory-region: + Phandle to a memory region to allocate from, as defined in + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt + + +Example: + +gfx: display@1e6e6000 { + compatible = "aspeed,ast2500-gfx", "syscon"; + reg = <0x1e6e6000 0x1000>; + reg-io-width = <4>; + clocks = <&syscon ASPEED_CLK_GATE_D1CLK>; + resets = <&syscon ASPEED_RESET_CRT1>; + interrupts = <0x19>; + memory-region = <&gfx_memory>; +}; + +gfx_memory: framebuffer { + size = <0x01000000>; + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; +}; diff --git a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt index c907aa8dd755..b2df82b44625 100644 --- a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt +++ b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt @@ -6,15 +6,20 @@ For V3D 2.x, see brcm,bcm-vc4.txt. Required properties: - compatible: Should be "brcm,7268-v3d" or "brcm,7278-v3d" - reg: Physical base addresses and lengths of the register areas -- reg-names: Names for the register areas. The "hub", "bridge", and "core0" +- reg-names: Names for the register areas. The "hub" and "core0" register areas are always required. The "gca" register area - is required if the GCA cache controller is present. + is required if the GCA cache controller is present. The + "bridge" register area is required if an external reset + controller is not present. - interrupts: The interrupt numbers. The first interrupt is for the hub, - while the following interrupts are for the cores. + while the following interrupts are separate interrupt lines + for the cores (if they don't share the hub's interrupt). See bindings/interrupt-controller/interrupts.txt Optional properties: - clocks: The core clock the unit runs on +- resets: The reset line for v3d, if not using a mapping of the bridge + See bindings/reset/reset.txt v3d { compatible = "brcm,7268-v3d"; |