summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/net/can
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/net/can')
-rw-r--r--Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt53
-rw-r--r--Documentation/devicetree/bindings/net/can/sja1000.txt53
2 files changed, 106 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt
new file mode 100644
index 000000000000..2fa4fcd38fd6
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt
@@ -0,0 +1,53 @@
+CAN Device Tree Bindings
+------------------------
+
+(c) 2006-2009 Secret Lab Technologies Ltd
+Grant Likely <grant.likely@secretlab.ca>
+
+fsl,mpc5200-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source shall be used for the controller:
+
+- fsl,mscan-clock-source : a string describing the clock source. Valid values
+ are: "ip" for ip bus clock
+ "ref" for reference clock (XTAL)
+ "ref" is default in case this property is not
+ present.
+
+fsl,mpc5121-mscan nodes
+-----------------------
+In addition to the required compatible-, reg- and interrupt-properties, you can
+also specify which clock source and divider shall be used for the controller:
+
+- fsl,mscan-clock-source : a string describing the clock source. Valid values
+ are: "ip" for ip bus clock
+ "ref" for reference clock
+ "sys" for system clock
+ If this property is not present, an optimal CAN
+ clock source and frequency based on the system
+ clock will be selected. If this is not possible,
+ the reference clock will be used.
+
+- fsl,mscan-clock-divider: for the reference and system clock, an additional
+ clock divider can be specified. By default, a
+ value of 1 is used.
+
+Note that the MPC5121 Rev. 1 processor is not supported.
+
+Examples:
+ can@1300 {
+ compatible = "fsl,mpc5121-mscan";
+ interrupts = <12 0x8>;
+ interrupt-parent = <&ipic>;
+ reg = <0x1300 0x80>;
+ };
+
+ can@1380 {
+ compatible = "fsl,mpc5121-mscan";
+ interrupts = <13 0x8>;
+ interrupt-parent = <&ipic>;
+ reg = <0x1380 0x80>;
+ fsl,mscan-clock-source = "ref";
+ fsl,mscan-clock-divider = <3>;
+ };
diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt
new file mode 100644
index 000000000000..d6d209ded937
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/can/sja1000.txt
@@ -0,0 +1,53 @@
+Memory mapped SJA1000 CAN controller from NXP (formerly Philips)
+
+Required properties:
+
+- compatible : should be "nxp,sja1000".
+
+- reg : should specify the chip select, address offset and size required
+ to map the registers of the SJA1000. The size is usually 0x80.
+
+- interrupts: property with a value describing the interrupt source
+ (number and sensitivity) required for the SJA1000.
+
+Optional properties:
+
+- nxp,external-clock-frequency : Frequency of the external oscillator
+ clock in Hz. Note that the internal clock frequency used by the
+ SJA1000 is half of that value. If not specified, a default value
+ of 16000000 (16 MHz) is used.
+
+- nxp,tx-output-mode : operation mode of the TX output control logic:
+ <0x0> : bi-phase output mode
+ <0x1> : normal output mode (default)
+ <0x2> : test output mode
+ <0x3> : clock output mode
+
+- nxp,tx-output-config : TX output pin configuration:
+ <0x01> : TX0 invert
+ <0x02> : TX0 pull-down (default)
+ <0x04> : TX0 pull-up
+ <0x06> : TX0 push-pull
+ <0x08> : TX1 invert
+ <0x10> : TX1 pull-down
+ <0x20> : TX1 pull-up
+ <0x30> : TX1 push-pull
+
+- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin.
+ If not specified or if the specified value is 0, the CLKOUT pin
+ will be disabled.
+
+- nxp,no-comparator-bypass : Allows to disable the CAN input comperator.
+
+For futher information, please have a look to the SJA1000 data sheet.
+
+Examples:
+
+can@3,100 {
+ compatible = "nxp,sja1000";
+ reg = <3 0x100 0x80>;
+ interrupts = <2 0>;
+ interrupt-parent = <&mpic>;
+ nxp,external-clock-frequency = <16000000>;
+};
+