summaryrefslogtreecommitdiff
path: root/Documentation/devicetree/bindings/sound/cs42l56.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/sound/cs42l56.txt')
-rw-r--r--Documentation/devicetree/bindings/sound/cs42l56.txt63
1 files changed, 63 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs42l56.txt b/Documentation/devicetree/bindings/sound/cs42l56.txt
new file mode 100644
index 000000000000..4feb0eb27ea4
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs42l56.txt
@@ -0,0 +1,63 @@
+CS42L52 audio CODEC
+
+Required properties:
+
+ - compatible : "cirrus,cs42l56"
+
+ - reg : the I2C address of the device for I2C
+
+ - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
+ as covered in Documentation/devicetree/bindings/regulator/regulator.txt.
+
+Optional properties:
+
+ - cirrus,gpio-nreset : GPIO controller's phandle and the number
+ of the GPIO used to reset the codec.
+
+ - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
+ Allowable values of 0x00 through 0x0F. These are raw values written to the
+ register, not the actual frequency. The frequency is determined by the following.
+ Frequency = MCLK / 4 * (N+2)
+ N = chgfreq_val
+ MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit.
+
+ - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
+ as a pseudo-differential input referenced to AIN1REF/AIN3A.
+
+ - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
+ as a pseudo-differential input referenced to AIN2REF/AIN3B.
+
+ - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
+ 0 = 0.5 x VA
+ 1 = 0.6 x VA
+ 2 = 0.7 x VA
+ 3 = 0.8 x VA
+ 4 = 0.83 x VA
+ 5 = 0.91 x VA
+
+ - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout
+ Amplifiers adapt to the output signal levels.
+ 0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings.
+ 1 = Fixed - Headphone and Line Amp supply = + or - VCP/2.
+ 2 = Fixed - Headphone and Line Amp supply = + or - VCP.
+ 3 = Adapted to Signal; Voltage level is dynamically determined by the output signal.
+
+ - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass
+ Filter.
+ 0 = 1.8Hz
+ 1 = 119Hz
+ 2 = 236Hz
+ 3 = 464Hz
+
+
+Example:
+
+codec: codec@4b {
+ compatible = "cirrus,cs42l56";
+ reg = <0x4b>;
+ gpio-reset = <&gpio 10 0>;
+ cirrus,chgfreq-divisor = <0x05>;
+ cirrus.ain1_ref_cfg;
+ cirrus,micbias-lvl = <5>;
+ VA-supply = <&reg_audio>;
+};