diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
55 files changed, 1770 insertions, 71 deletions
diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.txt b/Documentation/devicetree/bindings/ata/ahci-platform.txt index f4006d3c9fdf..c760ecb81381 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.txt +++ b/Documentation/devicetree/bindings/ata/ahci-platform.txt @@ -30,7 +30,6 @@ compatible: Optional properties: - dma-coherent : Present if dma operations are coherent - clocks : a list of phandle + clock specifier pairs -- resets : a list of phandle + reset specifier pairs - target-supply : regulator for SATA target power - phys : reference to the SATA PHY node - phy-names : must be "sata-phy" diff --git a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt index 0047b1394c70..2c887536258c 100644 --- a/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt +++ b/Documentation/devicetree/bindings/display/bridge/adi,adv7511.txt @@ -14,7 +14,13 @@ Required properties: "adi,adv7513" "adi,adv7533" -- reg: I2C slave address +- reg: I2C slave addresses + The ADV7511 internal registers are split into four pages exposed through + different I2C addresses, creating four register maps. Each map has it own + I2C address and acts as a standard slave device on the I2C bus. The main + address is mandatory, others are optional and revert to defaults if not + specified. + The ADV7511 supports a large number of input data formats that differ by their color depth, color format, clock mode, bit justification and random @@ -70,6 +76,9 @@ Optional properties: rather than generate its own timings for HDMI output. - clocks: from common clock binding: reference to the CEC clock. - clock-names: from common clock binding: must be "cec". +- reg-names : Names of maps with programmable addresses. + It can contain any map needing a non-default address. + Possible maps names are : "main", "edid", "cec", "packet" Required nodes: @@ -88,7 +97,12 @@ Example adv7511w: hdmi@39 { compatible = "adi,adv7511w"; - reg = <39>; + /* + * The EDID page will be accessible on address 0x66 on the I2C + * bus. All other maps continue to use their default addresses. + */ + reg = <0x39>, <0x66>; + reg-names = "main", "edid"; interrupt-parent = <&gpio3>; interrupts = <29 IRQ_TYPE_EDGE_FALLING>; clocks = <&cec_clock>; diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt new file mode 100644 index 000000000000..f5725bb6c61c --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt @@ -0,0 +1,133 @@ +Cadence DSI bridge +================== + +The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes. + +Required properties: +- compatible: should be set to "cdns,dsi". +- reg: physical base address and length of the controller's registers. +- interrupts: interrupt line connected to the DSI bridge. +- clocks: DSI bridge clocks. +- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk". +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy". +- #address-cells: must be set to 1. +- #size-cells: must be set to 0. + +Optional properties: +- resets: DSI reset lines. +- reset-names: can contain "dsi_p_rst". + +Required subnodes: +- ports: Ports as described in Documentation/devicetree/bindings/graph.txt. + 2 ports are available: + * port 0: this port is only needed if some of your DSI devices are + controlled through an external bus like I2C or SPI. Can have at + most 4 endpoints. The endpoint number is directly encoding the + DSI virtual channel used by this device. + * port 1: represents the DPI input. + Other ports will be added later to support the new kind of inputs. + +- one subnode per DSI device connected on the DSI bus. Each DSI device should + contain a reg property encoding its virtual channel. + +Cadence DPHY +============ + +Cadence DPHY block. + +Required properties: +- compatible: should be set to "cdns,dphy". +- reg: physical base address and length of the DPHY registers. +- clocks: DPHY reference clocks. +- clock-names: must contain "psm" and "pll_ref". +- #phy-cells: must be set to 0. + + +Example: + dphy0: dphy@fd0e0000{ + compatible = "cdns,dphy"; + reg = <0x0 0xfd0e0000 0x0 0x1000>; + clocks = <&psm_clk>, <&pll_ref_clk>; + clock-names = "psm", "pll_ref"; + #phy-cells = <0>; + }; + + dsi0: dsi@fd0c0000 { + compatible = "cdns,dsi"; + reg = <0x0 0xfd0c0000 0x0 0x1000>; + clocks = <&pclk>, <&sysclk>; + clock-names = "dsi_p_clk", "dsi_sys_clk"; + interrupts = <1>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + dsi0_dpi_input: endpoint { + remote-endpoint = <&xxx_dpi_output>; + }; + }; + }; + + panel: dsi-dev@0 { + compatible = "<vendor,panel>"; + reg = <0>; + }; + }; + +or + + dsi0: dsi@fd0c0000 { + compatible = "cdns,dsi"; + reg = <0x0 0xfd0c0000 0x0 0x1000>; + clocks = <&pclk>, <&sysclk>; + clock-names = "dsi_p_clk", "dsi_sys_clk"; + interrupts = <1>; + phys = <&dphy1>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + dsi0_output: endpoint@0 { + reg = <0>; + remote-endpoint = <&dsi_panel_input>; + }; + }; + + port@1 { + reg = <1>; + dsi0_dpi_input: endpoint { + remote-endpoint = <&xxx_dpi_output>; + }; + }; + }; + }; + + i2c@xxx { + panel: panel@59 { + compatible = "<vendor,panel>"; + reg = <0x59>; + + port { + dsi_panel_input: endpoint { + remote-endpoint = <&dsi0_output>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt index 3a72a103a18a..a41d280c3f9f 100644 --- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt +++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt @@ -14,6 +14,7 @@ Required properties: - compatible : Shall contain one or more of - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX + - "renesas,r8a77965-hdmi" for R8A77965 (R-Car M3-N) compatible HDMI TX - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX When compatible with generic versions, nodes must list the SoC-specific diff --git a/Documentation/devicetree/bindings/display/bridge/tda998x.txt b/Documentation/devicetree/bindings/display/bridge/tda998x.txt index 24cc2466185a..1a4eaca40d94 100644 --- a/Documentation/devicetree/bindings/display/bridge/tda998x.txt +++ b/Documentation/devicetree/bindings/display/bridge/tda998x.txt @@ -27,6 +27,9 @@ Optional properties: in question is used. The implementation allows one or two DAIs. If two DAIs are defined, they must be of different type. + - nxp,calib-gpios: calibration GPIO, which must correspond with the + gpio used for the TDA998x interrupt pin. + [1] Documentation/sound/alsa/soc/DAI.txt [2] include/dt-bindings/display/tda998x.h diff --git a/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt new file mode 100644 index 000000000000..37f0c04d5a28 --- /dev/null +++ b/Documentation/devicetree/bindings/display/bridge/thine,thc63lvd1024.txt @@ -0,0 +1,60 @@ +Thine Electronics THC63LVD1024 LVDS decoder +------------------------------------------- + +The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS streams +to parallel data outputs. The chip supports single/dual input/output modes, +handling up to two LVDS input streams and up to two digital CMOS/TTL outputs. + +Single or dual operation mode, output data mapping and DDR output modes are +configured through input signals and the chip does not expose any control bus. + +Required properties: +- compatible: Shall be "thine,thc63lvd1024" +- vcc-supply: Power supply for TTL output, TTL CLOCKOUT signal, LVDS input, + PPL and digital circuitry + +Optional properties: +- powerdown-gpios: Power down GPIO signal, pin name "/PDWN". Active low +- oe-gpios: Output enable GPIO signal, pin name "OE". Active high + +The THC63LVD1024 video port connections are modeled according +to OF graph bindings specified by Documentation/devicetree/bindings/graph.txt + +Required video port nodes: +- port@0: First LVDS input port +- port@2: First digital CMOS/TTL parallel output + +Optional video port nodes: +- port@1: Second LVDS input port +- port@3: Second digital CMOS/TTL parallel output + +Example: +-------- + + thc63lvd1024: lvds-decoder { + compatible = "thine,thc63lvd1024"; + + vcc-supply = <®_lvds_vcc>; + powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lvds_dec_in_0: endpoint { + remote-endpoint = <&lvds_out>; + }; + }; + + port@2{ + reg = <2>; + + lvds_dec_out_2: endpoint { + remote-endpoint = <&adv7511_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt index fc2588292a68..775193e1c641 100644 --- a/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt +++ b/Documentation/devicetree/bindings/display/exynos/exynos5433-decon.txt @@ -19,7 +19,8 @@ Required properties: clock-names property. - clock-names: list of clock names sorted in the same order as the clocks property. Must contain "pclk", "aclk_decon", "aclk_smmu_decon0x", - "aclk_xiu_decon0x", "pclk_smmu_decon0x", clk_decon_vclk", + "aclk_xiu_decon0x", "pclk_smmu_decon0x", "aclk_smmu_decon1x", + "aclk_xiu_decon1x", "pclk_smmu_decon1x", clk_decon_vclk", "sclk_decon_eclk" - ports: contains a port which is connected to mic node. address-cells and size-cells must 1 and 0, respectively. @@ -34,10 +35,14 @@ decon: decon@13800000 { clocks = <&cmu_disp CLK_ACLK_DECON>, <&cmu_disp CLK_ACLK_SMMU_DECON0X>, <&cmu_disp CLK_ACLK_XIU_DECON0X>, <&cmu_disp CLK_PCLK_SMMU_DECON0X>, + <&cmu_disp CLK_ACLK_SMMU_DECON1X>, + <&cmu_disp CLK_ACLK_XIU_DECON1X>, + <&cmu_disp CLK_PCLK_SMMU_DECON1X>, <&cmu_disp CLK_SCLK_DECON_VCLK>, <&cmu_disp CLK_SCLK_DECON_ECLK>; clock-names = "aclk_decon", "aclk_smmu_decon0x", "aclk_xiu_decon0x", - "pclk_smmu_decon0x", "sclk_decon_vclk", "sclk_decon_eclk"; + "pclk_smmu_decon0x", "aclk_smmu_decon1x", "aclk_xiu_decon1x", + "pclk_smmu_decon1x", "sclk_decon_vclk", "sclk_decon_eclk"; interrupt-names = "vsync", "lcd_sys"; interrupts = <0 202 0>, <0 203 0>; diff --git a/Documentation/devicetree/bindings/display/panel/panel-common.txt b/Documentation/devicetree/bindings/display/panel/panel-common.txt index 557fa765adcb..5d2519af4bb5 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-common.txt +++ b/Documentation/devicetree/bindings/display/panel/panel-common.txt @@ -38,7 +38,7 @@ Display Timings require specific display timings. The panel-timing subnode expresses those timings as specified in the timing subnode section of the display timing bindings defined in - Documentation/devicetree/bindings/display/display-timing.txt. + Documentation/devicetree/bindings/display/panel/display-timing.txt. Connectivity diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt index c9cd17f99702..7c6854bd0a04 100644 --- a/Documentation/devicetree/bindings/display/renesas,du.txt +++ b/Documentation/devicetree/bindings/display/renesas,du.txt @@ -13,6 +13,7 @@ Required Properties: - "renesas,du-r8a7794" for R8A7794 (R-Car E2) compatible DU - "renesas,du-r8a7795" for R8A7795 (R-Car H3) compatible DU - "renesas,du-r8a7796" for R8A7796 (R-Car M3-W) compatible DU + - "renesas,du-r8a77965" for R8A77965 (R-Car M3-N) compatible DU - "renesas,du-r8a77970" for R8A77970 (R-Car V3M) compatible DU - "renesas,du-r8a77995" for R8A77995 (R-Car D3) compatible DU @@ -47,20 +48,21 @@ bindings specified in Documentation/devicetree/bindings/graph.txt. The following table lists for each supported model the port number corresponding to each DU output. - Port0 Port1 Port2 Port3 + Port0 Port1 Port2 Port3 ----------------------------------------------------------------------------- - R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - - R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - - R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - - R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - - R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - - R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - - R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - - R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - - R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 - R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - - R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - - R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - + R8A7743 (RZ/G1M) DPAD 0 LVDS 0 - - + R8A7745 (RZ/G1E) DPAD 0 DPAD 1 - - + R8A7779 (R-Car H1) DPAD 0 DPAD 1 - - + R8A7790 (R-Car H2) DPAD 0 LVDS 0 LVDS 1 - + R8A7791 (R-Car M2-W) DPAD 0 LVDS 0 - - + R8A7792 (R-Car V2H) DPAD 0 DPAD 1 - - + R8A7793 (R-Car M2-N) DPAD 0 LVDS 0 - - + R8A7794 (R-Car E2) DPAD 0 DPAD 1 - - + R8A7795 (R-Car H3) DPAD 0 HDMI 0 HDMI 1 LVDS 0 + R8A7796 (R-Car M3-W) DPAD 0 HDMI 0 LVDS 0 - + R8A77965 (R-Car M3-N) DPAD 0 HDMI 0 LVDS 0 - + R8A77970 (R-Car V3M) DPAD 0 LVDS 0 - - + R8A77995 (R-Car D3) DPAD 0 LVDS 0 LVDS 1 - Example: R8A7795 (R-Car H3) ES2.0 DU diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file mode 100644 index 000000000000..6a6cf5de08b0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt @@ -0,0 +1,93 @@ +Allwinner A31 DSI Encoder +========================= + +The DSI pipeline consists of two separate blocks: the DSI controller +itself, and its associated D-PHY. + +DSI Encoder +----------- + +The DSI Encoder generates the DSI signal from the TCON's. + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dsi + - reg: base address and size of memory-mapped region + - interrupts: interrupt associated to this IP + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - phys: phandle to the D-PHY + - phy-names: must be "dphy" + - resets: phandle to the reset controller driving the encoder + + - ports: A ports node with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. The + first port should be the input endpoint, usually coming from the + associated TCON. + +Any MIPI-DSI device attached to this should be described according to +the bindings defined in ../mipi-dsi-bus.txt + +D-PHY +----- + +Required properties: + - compatible: value must be one of: + * allwinner,sun6i-a31-mipi-dphy + - reg: base address and size of memory-mapped region + - clocks: phandles to the clocks feeding the DSI encoder + * bus: the DSI interface clock + * mod: the DSI module clock + - clock-names: the clock names mentioned above + - resets: phandle to the reset controller driving the encoder + +Example: + +dsi0: dsi@1ca0000 { + compatible = "allwinner,sun6i-a31-mipi-dsi"; + reg = <0x01ca0000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_SCLK>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + phys = <&dphy0>; + phy-names = "dphy"; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "bananapi,lhr050h41", "ilitek,ili9881c"; + reg = <0>; + power-gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; /* PB07 */ + reset-gpios = <&r_pio 0 5 GPIO_ACTIVE_LOW>; /* PL05 */ + backlight = <&pwm_bl>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + dsi0_in_tcon0: endpoint { + remote-endpoint = <&tcon0_out_dsi0>; + }; + }; + }; +}; + +dphy0: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + clocks = <&ccu CLK_BUS_MIPI_DSI>, + <&ccu CLK_DSI_DPHY>; + clock-names = "bus", "mod"; + resets = <&ccu RST_BUS_MIPI_DSI>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt index aadfb236d53a..61315eaa7660 100644 --- a/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt +++ b/Documentation/devicetree/bindings/dma/renesas,rcar-dmac.txt @@ -26,6 +26,7 @@ Required Properties: - "renesas,dmac-r8a7794" (R-Car E2) - "renesas,dmac-r8a7795" (R-Car H3) - "renesas,dmac-r8a7796" (R-Car M3-W) + - "renesas,dmac-r8a77965" (R-Car M3-N) - "renesas,dmac-r8a77970" (R-Car V3M) - "renesas,dmac-r8a77980" (R-Car V3H) diff --git a/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt new file mode 100644 index 000000000000..a8c362eb160c --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/lattice-machxo2-spi.txt @@ -0,0 +1,29 @@ +Lattice MachXO2 Slave SPI FPGA Manager + +Lattice MachXO2 FPGAs support a method of loading the bitstream over +'slave SPI' interface. + +See 'MachXO2ProgrammingandConfigurationUsageGuide.pdf' on www.latticesemi.com + +Required properties: +- compatible: should contain "lattice,machxo2-slave-spi" +- reg: spi chip select of the FPGA + +Example for full FPGA configuration: + + fpga-region0 { + compatible = "fpga-region"; + fpga-mgr = <&fpga_mgr_spi>; + #address-cells = <0x1>; + #size-cells = <0x1>; + }; + + spi1: spi@2000 { + ... + + fpga_mgr_spi: fpga-mgr@0 { + compatible = "lattice,machxo2-slave-spi"; + spi-max-frequency = <8000000>; + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt new file mode 100644 index 000000000000..c907aa8dd755 --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/brcm,bcm-v3d.txt @@ -0,0 +1,28 @@ +Broadcom V3D GPU + +Only the Broadcom V3D 3.x and newer GPUs are covered by this binding. +For V3D 2.x, see brcm,bcm-vc4.txt. + +Required properties: +- compatible: Should be "brcm,7268-v3d" or "brcm,7278-v3d" +- reg: Physical base addresses and lengths of the register areas +- reg-names: Names for the register areas. The "hub", "bridge", and "core0" + register areas are always required. The "gca" register area + is required if the GCA cache controller is present. +- interrupts: The interrupt numbers. The first interrupt is for the hub, + while the following interrupts are for the cores. + See bindings/interrupt-controller/interrupts.txt + +Optional properties: +- clocks: The core clock the unit runs on + +v3d { + compatible = "brcm,7268-v3d"; + reg = <0xf1204000 0x100>, + <0xf1200000 0x4000>, + <0xf1208000 0x4000>, + <0xf1204100 0x100>; + reg-names = "bridge", "hub", "core0", "gca"; + interrupts = <0 78 4>, + <0 77 4>; +}; diff --git a/Documentation/devicetree/bindings/gpu/samsung-scaler.txt b/Documentation/devicetree/bindings/gpu/samsung-scaler.txt new file mode 100644 index 000000000000..9c3d98105dfd --- /dev/null +++ b/Documentation/devicetree/bindings/gpu/samsung-scaler.txt @@ -0,0 +1,27 @@ +* Samsung Exynos Image Scaler + +Required properties: + - compatible : value should be one of the following: + (a) "samsung,exynos5420-scaler" for Scaler IP in Exynos5420 + (b) "samsung,exynos5433-scaler" for Scaler IP in Exynos5433 + + - reg : Physical base address of the IP registers and length of memory + mapped region. + + - interrupts : Interrupt specifier for scaler interrupt, according to format + specific to interrupt parent. + + - clocks : Clock specifier for scaler clock, according to generic clock + bindings. (See Documentation/devicetree/bindings/clock/exynos*.txt) + + - clock-names : Names of clocks. For exynos scaler, it should be "mscl" + on 5420 and "pclk", "aclk" and "aclk_xiu" on 5433. + +Example: + scaler@12800000 { + compatible = "samsung,exynos5420-scaler"; + reg = <0x12800000 0x1294>; + interrupts = <0 220 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clock CLK_MSCL0>; + clock-names = "mscl"; + }; diff --git a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt index 439a7430fc68..2becdcfdc840 100644 --- a/Documentation/devicetree/bindings/hwmon/gpio-fan.txt +++ b/Documentation/devicetree/bindings/hwmon/gpio-fan.txt @@ -11,7 +11,7 @@ Optional properties: must have the RPM values in ascending order. - alarm-gpios: This pin going active indicates something is wrong with the fan, and a udev event will be fired. -- cooling-cells: If used as a cooling device, must be <2> +- #cooling-cells: If used as a cooling device, must be <2> Also see: Documentation/devicetree/bindings/thermal/thermal.txt min and max states are derived from the speed-map of the fan. diff --git a/Documentation/devicetree/bindings/hwmon/ltc2990.txt b/Documentation/devicetree/bindings/hwmon/ltc2990.txt new file mode 100644 index 000000000000..f92f54029e84 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/ltc2990.txt @@ -0,0 +1,36 @@ +ltc2990: Linear Technology LTC2990 power monitor + +Required properties: +- compatible: Must be "lltc,ltc2990" +- reg: I2C slave address +- lltc,meas-mode: + An array of two integers for configuring the chip measurement mode. + + The first integer defines the bits 2..0 in the control register. In all + cases the internal temperature and supply voltage are measured. In + addition the following input measurements are enabled per mode: + + 0: V1, V2, TR2 + 1: V1-V2, TR2 + 2: V1-V2, V3, V4 + 3: TR1, V3, V4 + 4: TR1, V3-V4 + 5: TR1, TR2 + 6: V1-V2, V3-V4 + 7: V1, V2, V3, V4 + + The second integer defines the bits 4..3 in the control register. This + allows a subset of the measurements to be enabled: + + 0: Internal temperature and supply voltage only + 1: TR1, V1 or V1-V2 only per mode + 2: TR2, V3 or V3-V4 only per mode + 3: All measurements per mode + +Example: + +ltc2990@4c { + compatible = "lltc,ltc2990"; + reg = <0x4c>; + lltc,meas-mode = <7 3>; /* V1, V2, V3, V4 */ +}; diff --git a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt index 23e3abc3fdef..c88919480d37 100644 --- a/Documentation/devicetree/bindings/input/atmel,maxtouch.txt +++ b/Documentation/devicetree/bindings/input/atmel,maxtouch.txt @@ -4,6 +4,13 @@ Required properties: - compatible: atmel,maxtouch + The following compatibles have been used in various products but are + deprecated: + atmel,qt602240_ts + atmel,atmel_mxt_ts + atmel,atmel_mxt_tp + atmel,mXT224 + - reg: The I2C address of the device - interrupts: The sink for the touchpad's IRQ output diff --git a/Documentation/devicetree/bindings/input/elan_i2c.txt b/Documentation/devicetree/bindings/input/elan_i2c.txt index ee3242c4ba67..d80a83583238 100644 --- a/Documentation/devicetree/bindings/input/elan_i2c.txt +++ b/Documentation/devicetree/bindings/input/elan_i2c.txt @@ -14,6 +14,7 @@ Optional properties: - pinctrl-0: a phandle pointing to the pin settings for the device (see pinctrl binding [1]). - vcc-supply: a phandle for the regulator supplying 3.3V power. +- elan,trackpoint: touchpad can support a trackpoint (boolean) [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt [1]: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt index a83f9a5734ca..89674ad8a097 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -9,11 +9,12 @@ number of interrupt exposed depends on the SoC. Required properties: -- compatible : must have "amlogic,meson8-gpio-intc” and either - “amlogic,meson8-gpio-intc” for meson8 SoCs (S802) or - “amlogic,meson8b-gpio-intc” for meson8b SoCs (S805) or - “amlogic,meson-gxbb-gpio-intc” for GXBB SoCs (S905) or - “amlogic,meson-gxl-gpio-intc” for GXL SoCs (S905X, S912) +- compatible : must have "amlogic,meson8-gpio-intc" and either + "amlogic,meson8-gpio-intc" for meson8 SoCs (S802) or + "amlogic,meson8b-gpio-intc" for meson8b SoCs (S805) or + "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or + "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) + "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) - interrupt-parent : a phandle to the GIC the interrupts are routed to. Usually this is provided at the root level of the device tree as it is common to most of the SoC. diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt index 0a57f2f4167d..3ea78c4ef887 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic-v3.txt @@ -57,6 +57,20 @@ Optional occupied by the redistributors. Required if more than one such region is present. +- msi-controller: Boolean property. Identifies the node as an MSI + controller. Only present if the Message Based Interrupt + functionnality is being exposed by the HW, and the mbi-ranges + property present. + +- mbi-ranges: A list of pairs <intid span>, where "intid" is the first + SPI of a range that can be used an MBI, and "span" the size of that + range. Multiple ranges can be provided. Requires "msi-controller" to + be set. + +- mbi-alias: Address property. Base address of an alias of the GICD + region containing only the {SET,CLR}SPI registers to be used if + isolation is required, and if supported by the HW. + Sub-nodes: PPI affinity can be expressed as a single "ppi-partitions" node, @@ -99,6 +113,9 @@ Examples: <0x0 0x2c020000 0 0x2000>; // GICV interrupts = <1 9 4>; + msi-controller; + mbi-ranges = <256 128>; + gic-its@2c200000 { compatible = "arm,gic-v3-its"; msi-controller; diff --git a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt index edf03f09244b..136bd612bd83 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/st,stm32-exti.txt @@ -5,11 +5,14 @@ Required properties: - compatible: Should be: "st,stm32-exti" "st,stm32h7-exti" + "st,stm32mp1-exti" - reg: Specifies base physical address and size of the registers - interrupt-controller: Indentifies the node as an interrupt controller - #interrupt-cells: Specifies the number of cells to encode an interrupt specifier, shall be 2 - interrupts: interrupts references to primary interrupt controller + (only needed for exti controller with multiple exti under + same parent interrupt: st,stm32-exti and st,stm32h7-exti") Example: diff --git a/Documentation/devicetree/bindings/leds/leds-cr0014114.txt b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt new file mode 100644 index 000000000000..4255b19ad25c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-cr0014114.txt @@ -0,0 +1,54 @@ +Crane Merchandising System - cr0014114 LED driver +------------------------------------------------- + +This LED Board is widely used in vending machines produced +by Crane Merchandising Systems. + +Required properties: +- compatible: "crane,cr0014114" + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + +LED sub-node properties: +- label : + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + +Example +------- + +led-controller@0 { + compatible = "crane,cr0014114"; + reg = <0>; + spi-max-frequency = <50000>; + #address-cells = <1>; + #size-cells = <0>; + + led@0 { + reg = <0>; + label = "red:coin"; + }; + led@1 { + reg = <1>; + label = "green:coin"; + }; + led@2 { + reg = <2>; + label = "blue:coin"; + }; + led@3 { + reg = <3>; + label = "red:bill"; + }; + led@4 { + reg = <4>; + label = "green:bill"; + }; + led@5 { + reg = <5>; + label = "blue:bill"; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/leds/leds-lm3601x.txt b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt new file mode 100644 index 000000000000..a88b2c41e75b --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3601x.txt @@ -0,0 +1,45 @@ +* Texas Instruments - lm3601x Single-LED Flash Driver + +The LM3601X are ultra-small LED flash drivers that +provide a high level of adjustability. + +Required properties: + - compatible : Can be one of the following + "ti,lm36010" + "ti,lm36011" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Required child properties: + - reg : 0 - Indicates a IR mode + 1 - Indicates a Torch (white LED) mode + +Required properties for flash LED child nodes: + See Documentation/devicetree/bindings/leds/common.txt + - flash-max-microamp : Range from 11mA - 1.5A + - flash-max-timeout-us : Range from 40ms - 1600ms + - led-max-microamp : Range from 2.4mA - 376mA + +Optional child properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + +Example: +led-controller@64 { + compatible = "ti,lm36010"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x64>; + + led@0 { + reg = <1>; + label = "white:torch"; + led-max-microamp = <376000>; + flash-max-microamp = <1500000>; + flash-max-timeout-us = <1600000>; + }; +} + +For more product information please see the links below: +http://www.ti.com/product/LM36010 +http://www.ti.com/product/LM36011 diff --git a/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt new file mode 100644 index 000000000000..dddf84f9c7ea --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-sc27xx-bltc.txt @@ -0,0 +1,41 @@ +LEDs connected to Spreadtrum SC27XX PMIC breathing light controller + +The SC27xx breathing light controller supports to 3 outputs: +red LED, green LED and blue LED. Each LED can work at normal +PWM mode or breath light mode. + +Required properties: +- compatible: Should be "sprd,sc2731-bltc". +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- reg: Specify the controller address. + +Required child properties: +- reg: Port this LED is connected to. + +Optional child properties: +- label: See Documentation/devicetree/bindings/leds/common.txt. + +Examples: + +led-controller@200 { + compatible = "sprd,sc2731-bltc"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x200>; + + led@0 { + label = "red"; + reg = <0x0>; + }; + + led@1 { + label = "green"; + reg = <0x1>; + }; + + led@2 { + label = "blue"; + reg = <0x2>; + }; +}; diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt index 50bf611a4d2c..13e70409e8ac 100644 --- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt +++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx.txt @@ -12,6 +12,7 @@ Required properties: - "amlogic,meson-gxbb-mmc" - "amlogic,meson-gxl-mmc" - "amlogic,meson-gxm-mmc" + - "amlogic,meson-axg-mmc" - clocks : A list of phandle + clock-specifier pairs for the clocks listed in clock-names. - clock-names: Should contain the following: "core" - Main peripheral bus clock @@ -19,6 +20,7 @@ Required properties: "clkin1" - Other parent clock of internal mux The driver has an internal mux clock which switches between clkin0 and clkin1 depending on the clock rate requested by the MMC core. +- resets : phandle of the internal reset line Example: @@ -29,4 +31,5 @@ Example: clocks = <&clkc CLKID_SD_EMMC_A>, <&xtal>, <&clkc CLKID_FCLK_DIV2>; clock-names = "core", "clkin0", "clkin1"; pinctrl-0 = <&emmc_pins>; + resets = <&reset RESET_SD_EMMC_A>; }; diff --git a/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt new file mode 100644 index 000000000000..b0f0999ea1a9 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/bluefield-dw-mshc.txt @@ -0,0 +1,29 @@ +* Mellanox Bluefield SoC specific extensions to the Synopsys Designware + Mobile Storage Host Controller + +Read synopsys-dw-mshc.txt for more details + +The Synopsys designware mobile storage host controller is used to interface +a SoC with storage medium such as eMMC or SD/MMC cards. This file documents +differences between the core Synopsys dw mshc controller properties described +by synopsys-dw-mshc.txt and the properties used by the Mellanox Bluefield SoC +specific extensions to the Synopsys Designware Mobile Storage Host Controller. + +Required Properties: + +* compatible: should be one of the following. + - "mellanox,bluefield-dw-mshc": for controllers with Mellanox Bluefield SoC + specific extensions. + +Example: + + /* Mellanox Bluefield SoC MMC */ + mmc@6008000 { + compatible = "mellanox,bluefield-dw-mshc"; + reg = <0x6008000 0x400>; + interrupts = <32>; + fifo-depth = <0x100>; + clock-frequency = <24000000>; + bus-width = <8>; + cap-mmc-highspeed; + }; diff --git a/Documentation/devicetree/bindings/mmc/jz4740.txt b/Documentation/devicetree/bindings/mmc/jz4740.txt new file mode 100644 index 000000000000..7cd8c432d7c8 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/jz4740.txt @@ -0,0 +1,38 @@ +* Ingenic JZ47xx MMC controllers + +This file documents the device tree properties used for the MMC controller in +Ingenic JZ4740/JZ4780 SoCs. These are in addition to the core MMC properties +described in mmc.txt. + +Required properties: +- compatible: Should be one of the following: + - "ingenic,jz4740-mmc" for the JZ4740 + - "ingenic,jz4780-mmc" for the JZ4780 +- reg: Should contain the MMC controller registers location and length. +- interrupts: Should contain the interrupt specifier of the MMC controller. +- clocks: Clock for the MMC controller. + +Optional properties: +- dmas: List of DMA specifiers with the controller specific format + as described in the generic DMA client binding. A tx and rx + specifier is required. +- dma-names: RX and TX DMA request names. + Should be "rx" and "tx", in that order. + +For additional details on DMA client bindings see ../dma/dma.txt. + +Example: + +mmc0: mmc@13450000 { + compatible = "ingenic,jz4780-mmc"; + reg = <0x13450000 0x1000>; + + interrupt-parent = <&intc>; + interrupts = <37>; + + clocks = <&cgu JZ4780_CLK_MSC0>; + clock-names = "mmc"; + + dmas = <&dma JZ4780_DMA_MSC0_RX 0xffffffff>, <&dma JZ4780_DMA_MSC0_TX 0xffffffff>; + dma-names = "rx", "tx"; +}; diff --git a/Documentation/devicetree/bindings/mmc/mmc.txt b/Documentation/devicetree/bindings/mmc/mmc.txt index 467cd7b147ce..f5a0923b34ca 100644 --- a/Documentation/devicetree/bindings/mmc/mmc.txt +++ b/Documentation/devicetree/bindings/mmc/mmc.txt @@ -19,6 +19,8 @@ Optional properties: - wp-gpios: Specify GPIOs for write protection, see gpio binding - cd-inverted: when present, polarity on the CD line is inverted. See the note below for the case, when a GPIO is used for the CD line +- cd-debounce-delay-ms: Set delay time before detecting card after card insert interrupt. + It's only valid when cd-gpios is present. - wp-inverted: when present, polarity on the WP line is inverted. See the note below for the case, when a GPIO is used for the WP line - disable-wp: When set no physical WP line is present. This property should @@ -56,6 +58,10 @@ Optional properties: - fixed-emmc-driver-type: for non-removable eMMC, enforce this driver type. The value <n> is the driver type as specified in the eMMC specification (table 206 in spec version 5.1). +- post-power-on-delay-ms : It was invented for MMC pwrseq-simple which could + be referred to mmc-pwrseq-simple.txt. But now it's reused as a tunable delay + waiting for I/O signalling and card power supply to be stable, regardless of + whether pwrseq-simple is used. Default to 10ms if no available. *NOTE* on CD and WP polarity. To use common for all SD/MMC host controllers line polarity properties, we have to fix the meaning of the "normal" and "inverted" diff --git a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt index 51775a372c06..393848c2138e 100644 --- a/Documentation/devicetree/bindings/mmc/sdhci-omap.txt +++ b/Documentation/devicetree/bindings/mmc/sdhci-omap.txt @@ -4,7 +4,14 @@ Refer to mmc.txt for standard MMC bindings. Required properties: - compatible: Should be "ti,dra7-sdhci" for DRA7 and DRA72 controllers + Should be "ti,k2g-sdhci" for K2G - ti,hwmods: Must be "mmc<n>", <n> is controller instance starting 1 + (Not required for K2G). +- pinctrl-names: Should be subset of "default", "hs", "sdr12", "sdr25", "sdr50", + "ddr50-rev11", "sdr104-rev11", "ddr50", "sdr104", + "ddr_1_8v-rev11", "ddr_1_8v" or "ddr_3_3v", "hs200_1_8v-rev11", + "hs200_1_8v", +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt Example: mmc1: mmc@4809c000 { diff --git a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt index 2d5287eeed95..ee978c95189d 100644 --- a/Documentation/devicetree/bindings/mmc/tmio_mmc.txt +++ b/Documentation/devicetree/bindings/mmc/tmio_mmc.txt @@ -26,6 +26,8 @@ Required properties: "renesas,sdhi-r8a7794" - SDHI IP on R8A7794 SoC "renesas,sdhi-r8a7795" - SDHI IP on R8A7795 SoC "renesas,sdhi-r8a7796" - SDHI IP on R8A7796 SoC + "renesas,sdhi-r8a77965" - SDHI IP on R8A77965 SoC + "renesas,sdhi-r8a77980" - SDHI IP on R8A77980 SoC "renesas,sdhi-r8a77995" - SDHI IP on R8A77995 SoC "renesas,sdhi-shmobile" - a generic sh-mobile SDHI controller "renesas,rcar-gen1-sdhi" - a generic R-Car Gen1 SDHI controller diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt index 93c3a6ae32f9..ac71daa46195 100644 --- a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -5,7 +5,9 @@ Required properties: - compatible: Must contain one or more of the following: - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. - - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3) compatible controller. + - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller. + - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller. + - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller. When compatible with the generic version, nodes must list the SoC-specific version corresponding to the platform first, followed by the diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt index 8acf51a4dfa8..47a6a7fe0b86 100644 --- a/Documentation/devicetree/bindings/net/dsa/b53.txt +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -10,6 +10,7 @@ Required properties: "brcm,bcm53128" "brcm,bcm5365" "brcm,bcm5395" + "brcm,bcm5389" "brcm,bcm5397" "brcm,bcm5398" diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt index 1814fa13f6ab..fc019df0d863 100644 --- a/Documentation/devicetree/bindings/net/marvell-pp2.txt +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -21,9 +21,10 @@ Required properties: - main controller clock (for both armada-375-pp2 and armada-7k-pp2) - GOP clock (for both armada-375-pp2 and armada-7k-pp2) - MG clock (only for armada-7k-pp2) + - MG Core clock (only for armada-7k-pp2) - AXI clock (only for armada-7k-pp2) -- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk" - and "axi_clk" (the 2 latter only for armada-7k-pp2). +- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk", + "mg_core_clk" and "axi_clk" (the 3 latter only for armada-7k-pp2). The ethernet ports are represented by subnodes. At least one port is required. @@ -80,8 +81,8 @@ cpm_ethernet: ethernet@0 { compatible = "marvell,armada-7k-pp22"; reg = <0x0 0x100000>, <0x129000 0xb000>; clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, - <&cpm_syscon0 1 5>, <&cpm_syscon0 1 18>; - clock-names = "pp_clk", "gop_clk", "gp_clk", "axi_clk"; + <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>; + clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk"; eth0: eth0 { interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>, diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt index 42a248301615..e22d8cfea687 100644 --- a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -57,6 +57,13 @@ KSZ9031: - txd2-skew-ps : Skew control of TX data 2 pad - txd3-skew-ps : Skew control of TX data 3 pad + - micrel,force-master: + Boolean, force phy to master mode. Only set this option if the phy + reference clock provided at CLK125_NDO pin is used as MAC reference + clock because the clock jitter in slave mode is to high (errata#2). + Attention: The link partner must be configurable as slave otherwise + no link will be established. + Examples: mdio { diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt index c306f55d335b..890526dbfc26 100644 --- a/Documentation/devicetree/bindings/net/renesas,ravb.txt +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -18,6 +18,7 @@ Required properties: - "renesas,etheravb-r8a7795" for the R8A7795 SoC. - "renesas,etheravb-r8a7796" for the R8A7796 SoC. + - "renesas,etheravb-r8a77965" for the R8A77965 SoC. - "renesas,etheravb-r8a77970" for the R8A77970 SoC. - "renesas,etheravb-r8a77980" for the R8A77980 SoC. - "renesas,etheravb-r8a77995" for the R8A77995 SoC. diff --git a/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt b/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt new file mode 100644 index 000000000000..d5e22fc67d66 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/zii,rave-sp-eeprom.txt @@ -0,0 +1,40 @@ +Zodiac Inflight Innovations RAVE EEPROM Bindings + +RAVE SP EEPROM device is a "MFD cell" device exposing physical EEPROM +attached to RAVE Supervisory Processor. It is expected that its Device +Tree node is specified as a child of the node corresponding to the +parent RAVE SP device (as documented in +Documentation/devicetree/bindings/mfd/zii,rave-sp.txt) + +Required properties: + +- compatible: Should be "zii,rave-sp-eeprom" + +Optional properties: + +- zii,eeprom-name: Unique EEPROM identifier describing its function in the + system. Will be used as created NVMEM deivce's name. + +Data cells: + +Data cells are child nodes of eerpom node, bindings for which are +documented in Documentation/bindings/nvmem/nvmem.txt + +Example: + + rave-sp { + compatible = "zii,rave-sp-rdu1"; + current-speed = <38400>; + + eeprom@a4 { + compatible = "zii,rave-sp-eeprom"; + reg = <0xa4 0x4000>; + #address-cells = <1>; + #size-cells = <1>; + zii,eeprom-name = "main-eeprom"; + + wdt_timeout: wdt-timeout@81 { + reg = <0x81 2>; + }; + }; + } diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt new file mode 100644 index 000000000000..c2127b96805a --- /dev/null +++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt @@ -0,0 +1,680 @@ +Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings +=================================== + +In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996 +that have KRYO processors, the CPU ferequencies subset and voltage value +of each OPP varies based on the silicon variant in use. +Qualcomm Technologies, Inc. Process Voltage Scaling Tables +defines the voltage and frequency value based on the msm-id in SMEM +and speedbin blown in the efuse combination. +The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC +to provide the OPP framework with required information (existing HW bitmap). +This is used to determine the voltage and frequency value for each OPP of +operating-points-v2 table when it is parsed by the OPP framework. + +Required properties: +-------------------- +In 'cpus' nodes: +- operating-points-v2: Phandle to the operating-points-v2 table to use. + +In 'operating-points-v2' table: +- compatible: Should be + - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996. +- nvmem-cells: A phandle pointing to a nvmem-cells node representing the + efuse registers that has information about the + speedbin that is used to select the right frequency/voltage + value pair. + Please refer the for nvmem-cells + bindings Documentation/devicetree/bindings/nvmem/nvmem.txt + and also examples below. + +In every OPP node: +- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW. + Bitmap: + 0: MSM8996 V3, speedbin 0 + 1: MSM8996 V3, speedbin 1 + 2: MSM8996 V3, speedbin 2 + 3: unused + 4: MSM8996 SG, speedbin 0 + 5: MSM8996 SG, speedbin 1 + 6: MSM8996 SG, speedbin 2 + 7-31: unused + +Example 1: +--------- + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x0>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU1: cpu@1 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x1>; + enable-method = "psci"; + clocks = <&kryocc 0>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster0_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_0>; + }; + + CPU2: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x100>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + L2_1: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + + CPU3: cpu@101 { + device_type = "cpu"; + compatible = "qcom,kryo"; + reg = <0x0 0x101>; + enable-method = "psci"; + clocks = <&kryocc 1>; + cpu-supply = <&pm8994_s11_saw>; + operating-points-v2 = <&cluster1_opp>; + #cooling-cells = <2>; + next-level-cache = <&L2_1>; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + }; + + cluster1 { + core0 { + cpu = <&CPU2>; + }; + + core1 { + cpu = <&CPU3>; + }; + }; + }; + }; + + cluster0_opp: opp_table0 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-422400000 { + opp-hz = /bits/ 64 <422400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-768000000 { + opp-hz = /bits/ 64 <768000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-844800000 { + opp-hz = /bits/ 64 <844800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-960000000 { + opp-hz = /bits/ 64 <960000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1228800000 { + opp-hz = /bits/ 64 <1228800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x72>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x5>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1497600000 { + opp-hz = /bits/ 64 <1497600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x4>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x20>; + clock-latency-ns = <200000>; + }; + opp-2188800000 { + opp-hz = /bits/ 64 <2188800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + + cluster1_opp: opp_table1 { + compatible = "operating-points-v2-kryo-cpu"; + nvmem-cells = <&speedbin_efuse>; + opp-shared; + + opp-307200000 { + opp-hz = /bits/ 64 <307200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x77>; + clock-latency-ns = <200000>; + }; + opp-384000000 { + opp-hz = /bits/ 64 <384000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-403200000 { + opp-hz = /bits/ 64 <403200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-460800000 { + opp-hz = /bits/ 64 <460800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-480000000 { + opp-hz = /bits/ 64 <480000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-537600000 { + opp-hz = /bits/ 64 <537600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-556800000 { + opp-hz = /bits/ 64 <556800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-614400000 { + opp-hz = /bits/ 64 <614400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-652800000 { + opp-hz = /bits/ 64 <652800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-691200000 { + opp-hz = /bits/ 64 <691200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-729600000 { + opp-hz = /bits/ 64 <729600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-748800000 { + opp-hz = /bits/ 64 <748800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-806400000 { + opp-hz = /bits/ 64 <806400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-825600000 { + opp-hz = /bits/ 64 <825600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-883200000 { + opp-hz = /bits/ 64 <883200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-902400000 { + opp-hz = /bits/ 64 <902400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-940800000 { + opp-hz = /bits/ 64 <940800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-979200000 { + opp-hz = /bits/ 64 <979200000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1036800000 { + opp-hz = /bits/ 64 <1036800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1056000000 { + opp-hz = /bits/ 64 <1056000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1113600000 { + opp-hz = /bits/ 64 <1113600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1132800000 { + opp-hz = /bits/ 64 <1132800000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1190400000 { + opp-hz = /bits/ 64 <1190400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1209600000 { + opp-hz = /bits/ 64 <1209600000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1286400000 { + opp-hz = /bits/ 64 <1286400000>; + opp-microvolt = <905000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1324800000 { + opp-hz = /bits/ 64 <1324800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1363200000 { + opp-hz = /bits/ 64 <1363200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1440000000 { + opp-hz = /bits/ 64 <1440000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1478400000 { + opp-hz = /bits/ 64 <1478400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1516800000 { + opp-hz = /bits/ 64 <1516800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1555200000 { + opp-hz = /bits/ 64 <1555200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1593600000 { + opp-hz = /bits/ 64 <1593600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1632000000 { + opp-hz = /bits/ 64 <1632000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1670400000 { + opp-hz = /bits/ 64 <1670400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1708800000 { + opp-hz = /bits/ 64 <1708800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1747200000 { + opp-hz = /bits/ 64 <1747200000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x70>; + clock-latency-ns = <200000>; + }; + opp-1785600000 { + opp-hz = /bits/ 64 <1785600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x7>; + clock-latency-ns = <200000>; + }; + opp-1804800000 { + opp-hz = /bits/ 64 <1804800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x6>; + clock-latency-ns = <200000>; + }; + opp-1824000000 { + opp-hz = /bits/ 64 <1824000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x71>; + clock-latency-ns = <200000>; + }; + opp-1900800000 { + opp-hz = /bits/ 64 <1900800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x74>; + clock-latency-ns = <200000>; + }; + opp-1920000000 { + opp-hz = /bits/ 64 <1920000000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-1977600000 { + opp-hz = /bits/ 64 <1977600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-1996800000 { + opp-hz = /bits/ 64 <1996800000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2054400000 { + opp-hz = /bits/ 64 <2054400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x30>; + clock-latency-ns = <200000>; + }; + opp-2073600000 { + opp-hz = /bits/ 64 <2073600000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x1>; + clock-latency-ns = <200000>; + }; + opp-2150400000 { + opp-hz = /bits/ 64 <2150400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x31>; + clock-latency-ns = <200000>; + }; + opp-2246400000 { + opp-hz = /bits/ 64 <2246400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + opp-2342400000 { + opp-hz = /bits/ 64 <2342400000>; + opp-microvolt = <1140000 905000 1140000>; + opp-supported-hw = <0x10>; + clock-latency-ns = <200000>; + }; + }; + +.... + +reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; +.... + smem_mem: smem-mem@86000000 { + reg = <0x0 0x86000000 0x0 0x200000>; + no-map; + }; +.... +}; + +smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; +}; + +soc { +.... + qfprom: qfprom@74000 { + compatible = "qcom,qfprom"; + reg = <0x00074000 0x8ff>; + #address-cells = <1>; + #size-cells = <1>; + .... + speedbin_efuse: speedbin@133 { + reg = <0x133 0x1>; + bits = <5 3>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/opp/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 4e4f30288c8b..c396c4c0af92 100644 --- a/Documentation/devicetree/bindings/opp/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -82,7 +82,10 @@ This defines voltage-current-frequency combinations along with other related properties. Required properties: -- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. +- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. This is a + required property for all device nodes but devices like power domains. The + power domain nodes must have another (implementation dependent) property which + uniquely identifies the OPP nodes. Optional properties: - opp-microvolt: voltage in micro Volts. @@ -159,7 +162,7 @@ Optional properties: - status: Marks the node enabled/disabled. -- required-opp: This contains phandle to an OPP node in another device's OPP +- required-opps: This contains phandle to an OPP node in another device's OPP table. It may contain an array of phandles, where each phandle points to an OPP of a different device. It should not contain multiple phandles to the OPP nodes in the same OPP table. This specifies the minimum required OPP of the diff --git a/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt new file mode 100644 index 000000000000..e7caefa0b9c2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mtk-xsphy.txt @@ -0,0 +1,109 @@ +MediaTek XS-PHY binding +-------------------------- + +The XS-PHY controller supports physical layer functionality for USB3.1 +GEN2 controller on MediaTek SoCs. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,<soc-model>-xsphy", "mediatek,xsphy", + soc-model is the name of SoC, such as mt3611 etc; + when using "mediatek,xsphy" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt3611-xsphy" + + - #address-cells, #size-cells : should use the same values as the root node + - ranges: must be present + +Optional properties (controller (parent) node): + - reg : offset and length of register shared by multiple U3 ports, + exclude port's private register, if only U2 ports provided, + shouldn't use the property. + - mediatek,src-ref-clk-mhz : u32, frequency of reference clock for slew rate + calibrate + - mediatek,src-coef : u32, coefficient for slew rate calibrate, depends on + SoC process + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names +- clock-names : must contain + "ref": 48M reference clock for HighSpeed analog phy; and 26M + reference clock for SuperSpeedPlus analog phy, sometimes is + 24M, 25M or 27M, depended on platform. +- #phy-cells : should be 1 + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +The following optional properties are only for debug or HQA test +Optional properties (PHY_TYPE_USB2 port (child) node): +- mediatek,eye-src : u32, the value of slew rate calibrate +- mediatek,eye-vrt : u32, the selection of VRT reference voltage +- mediatek,eye-term : u32, the selection of HS_TX TERM reference voltage +- mediatek,efuse-intr : u32, the selection of Internal Resistor + +Optional properties (PHY_TYPE_USB3 port (child) node): +- mediatek,efuse-intr : u32, the selection of Internal Resistor +- mediatek,efuse-tx-imp : u32, the selection of TX Impedance +- mediatek,efuse-rx-imp : u32, the selection of RX Impedance + +Banks layout of xsphy +------------------------------------------------------------- +port offset bank +u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM +u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM +u2 port2 0x2000 MISC + ... +u31 common 0x3000 DIG_GLB + 0x3100 PHYA_GLB +u31 port0 0x3400 DIG_LN_TOP + 0x3500 DIG_LN_TX0 + 0x3600 DIG_LN_RX0 + 0x3700 DIG_LN_DAIF + 0x3800 PHYA_LN +u31 port1 0x3a00 DIG_LN_TOP + 0x3b00 DIG_LN_TX0 + 0x3c00 DIG_LN_RX0 + 0x3d00 DIG_LN_DAIF + 0x3e00 PHYA_LN + ... + +DIG_GLB & PHYA_GLB are shared by U31 ports. + +Example: + +u3phy: usb-phy@11c40000 { + compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy"; + reg = <0 0x11c43000 0 0x0200>; + mediatek,src-ref-clk-mhz = <26>; + mediatek,src-coef = <17>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + u2port0: usb-phy@11c40000 { + reg = <0 0x11c40000 0 0x0400>; + clocks = <&clk48m>; + clock-names = "ref"; + mediatek,eye-src = <4>; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11c43000 { + reg = <0 0x11c43400 0 0x0500>; + clocks = <&clk26m>; + clock-names = "ref"; + mediatek,efuse-intr = <28>; + #phy-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt index dcf1b8f691d5..266a1bb8bb6e 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt @@ -9,7 +9,8 @@ Required properties: "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074 "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996, "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996, - "qcom,qmp-v3-usb3-phy" for USB3 QMP V3 phy. + "qcom,sdm845-qmp-usb3-phy" for USB3 QMP V3 phy on sdm845, + "qcom,sdm845-qmp-usb3-uni-phy" for USB3 QMP V3 UNI phy on sdm845. - reg: offset and length of register set for PHY's common serdes block. diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt index 42c97426836e..03025d97998b 100644 --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt @@ -6,7 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. Required properties: - compatible: compatible list, contains "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996, - "qcom,qusb2-v2-phy" for QUSB2 V2 PHY. + "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845. - reg: offset and length of the PHY register set. - #phy-cells: must be 0. @@ -27,6 +27,27 @@ Optional properties: tuning parameter value for qusb2 phy. - qcom,tcsr-syscon: Phandle to TCSR syscon register region. + - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY + tuning parameter that may vary for different boards of same SOC. + This property is applicable to only QUSB2 v2 PHY (sdm845). + - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX + output current. + Possible range is - 15mA to 24mA (stepsize of 600 uA). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 22.2mA for sdm845. + - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level. + Possible range is 0 to 15% (stepsize of 5%). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is 10% for sdm845. +- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX + pre-emphasis (specified using qcom,preemphasis-level) must be in + effect. Duration could be half-bit of full-bit. + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + This property is applicable to only QUSB2 v2 PHY (sdm845). + Default value is full-bit width for sdm845. Example: hsusb_phy: phy@7411000 { diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index ed5eb547afc8..64bc5c2a76da 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -56,9 +56,9 @@ pins it needs, and how they should be configured, with regard to muxer configuration, drive strength and pullups. If one of these options is not set, its actual value will be unspecified. -This driver supports the generic pin multiplexing and configuration -bindings. For details on each properties, you can refer to -./pinctrl-bindings.txt. +Allwinner A1X Pin Controller supports the generic pin multiplexing and +configuration bindings. For details on each properties, you can refer to + ./pinctrl-bindings.txt. Required sub-node properties: - pins diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index f3355313c020..4733f76cbe48 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -127,7 +127,7 @@ inside a PM domain with index 0 of a power controller represented by a node with the label "power". Optional properties: -- required-opp: This contains phandle to an OPP node in another device's OPP +- required-opps: This contains phandle to an OPP node in another device's OPP table. It may contain an array of phandles, where each phandle points to an OPP of a different device. It should not contain multiple phandles to the OPP nodes in the same OPP table. This specifies the minimum required OPP of the @@ -175,14 +175,14 @@ Example: compatible = "foo,i-leak-current"; reg = <0x12350000 0x1000>; power-domains = <&power 0>; - required-opp = <&domain0_opp_0>; + required-opps = <&domain0_opp_0>; }; leaky-device1@12350000 { compatible = "foo,i-leak-current"; reg = <0x12350000 0x1000>; power-domains = <&power 1>; - required-opp = <&domain1_opp_1>; + required-opps = <&domain1_opp_1>; }; [1]. Documentation/devicetree/bindings/power/domain-idle-state.txt diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index 4a4766e9c254..e66fd4eab71c 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -31,6 +31,8 @@ SoC is on the same page. Required properties: - compatible: should be one of: + - "rockchip,px30-io-voltage-domain" for px30 + - "rockchip,px30-pmu-io-voltage-domain" for px30 pmu-domains - "rockchip,rk3188-io-voltage-domain" for rk3188 - "rockchip,rk3228-io-voltage-domain" for rk3228 - "rockchip,rk3288-io-voltage-domain" for rk3288 @@ -51,6 +53,19 @@ a phandle the relevant regulator. All specified supplies must be able to report their voltage. The IO Voltage Domain for any non-specified supplies will be not be touched. +Possible supplies for PX30: +- vccio6-supply: The supply connected to VCCIO6. +- vccio1-supply: The supply connected to VCCIO1. +- vccio2-supply: The supply connected to VCCIO2. +- vccio3-supply: The supply connected to VCCIO3. +- vccio4-supply: The supply connected to VCCIO4. +- vccio5-supply: The supply connected to VCCIO5. +- vccio-oscgpi-supply: The supply connected to VCCIO_OSCGPI. + +Possible supplies for PX30 pmu-domains: +- pmuio1-supply: The supply connected to PMUIO1. +- pmuio2-supply: The supply connected to PMUIO2. + Possible supplies for rk3188: - ap0-supply: The supply connected to AP0_VCC. - ap1-supply: The supply connected to AP1_VCC. diff --git a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt index 8ff65fa632fd..c06c045126fc 100644 --- a/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt +++ b/Documentation/devicetree/bindings/serial/amlogic,meson-uart.txt @@ -21,7 +21,7 @@ Required properties: - interrupts : identifier to the device interrupt - clocks : a list of phandle + clock-specifier pairs, one for each entry in clock names. -- clocks-names : +- clock-names : * "xtal" for external xtal clock identifier * "pclk" for the bus core clock, either the clk81 clock or the gate clock * "baud" for the source of the baudrate generator, can be either the xtal diff --git a/Documentation/devicetree/bindings/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/serial/mvebu-uart.txt index 2ae2fee7e023..b7e0e32b9ac6 100644 --- a/Documentation/devicetree/bindings/serial/mvebu-uart.txt +++ b/Documentation/devicetree/bindings/serial/mvebu-uart.txt @@ -24,7 +24,7 @@ Required properties: - Must contain two elements for the extended variant of the IP (marvell,armada-3700-uart-ext): "uart-tx" and "uart-rx", respectively the UART TX interrupt and the UART RX interrupt. A - corresponding interrupts-names property must be defined. + corresponding interrupt-names property must be defined. - For backward compatibility reasons, a single element interrupts property is also supported for the standard variant of the IP, containing only the UART sum interrupt. This form is deprecated diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index ad962f4ec3aa..106808b55b6d 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -17,6 +17,8 @@ Required properties: - "renesas,scifa-r8a7745" for R8A7745 (RZ/G1E) SCIFA compatible UART. - "renesas,scifb-r8a7745" for R8A7745 (RZ/G1E) SCIFB compatible UART. - "renesas,hscif-r8a7745" for R8A7745 (RZ/G1E) HSCIF compatible UART. + - "renesas,scif-r8a77470" for R8A77470 (RZ/G1C) SCIF compatible UART. + - "renesas,hscif-r8a77470" for R8A77470 (RZ/G1C) HSCIF compatible UART. - "renesas,scif-r8a7778" for R8A7778 (R-Car M1) SCIF compatible UART. - "renesas,scif-r8a7779" for R8A7779 (R-Car H1) SCIF compatible UART. - "renesas,scif-r8a7790" for R8A7790 (R-Car H2) SCIF compatible UART. @@ -41,6 +43,8 @@ Required properties: - "renesas,hscif-r8a7795" for R8A7795 (R-Car H3) HSCIF compatible UART. - "renesas,scif-r8a7796" for R8A7796 (R-Car M3-W) SCIF compatible UART. - "renesas,hscif-r8a7796" for R8A7796 (R-Car M3-W) HSCIF compatible UART. + - "renesas,scif-r8a77965" for R8A77965 (R-Car M3-N) SCIF compatible UART. + - "renesas,hscif-r8a77965" for R8A77965 (R-Car M3-N) HSCIF compatible UART. - "renesas,scif-r8a77970" for R8A77970 (R-Car V3M) SCIF compatible UART. - "renesas,hscif-r8a77970" for R8A77970 (R-Car V3M) HSCIF compatible UART. - "renesas,scif-r8a77980" for R8A77980 (R-Car V3H) SCIF compatible UART. diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 0e03344e2e8b..2e9318151df7 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -76,6 +76,10 @@ Optional properties: needs to make sure it does not send more than 90% maximum_periodic_data_per_frame. The use case is multiple transactions, but less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. It's expected that a mux state of 0 indicates device mode and a + mux state of 1 indicates host mode. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one @@ -102,4 +106,6 @@ Example: rx-burst-size-dword = <0x10>; extcon = <0>, <&usb_id>; phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0dbd3083e7dd..7f13ebef06cb 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -7,6 +7,26 @@ Required properties: - compatible: must be "snps,dwc3" - reg : Address and length of the register set for the device - interrupts: Interrupts used by the dwc3 controller. + - clock-names: should contain "ref", "bus_early", "suspend" + - clocks: list of phandle and clock specifier pairs corresponding to + entries in the clock-names property. + +Exception for clocks: + clocks are optional if the parent node (i.e. glue-layer) is compatible to + one of the following: + "amlogic,meson-axg-dwc3" + "amlogic,meson-gxl-dwc3" + "cavium,octeon-7130-usb-uctl" + "qcom,dwc3" + "samsung,exynos5250-dwusb3" + "samsung,exynos7-dwusb3" + "sprd,sc9860-dwc3" + "st,stih407-dwc3" + "ti,am437x-dwc3" + "ti,dwc3" + "ti,keystone-dwc3" + "rockchip,rk3399-dwc3" + "xlnx,zynqmp-dwc3" Optional properties: - usb-phy : array of phandle for the PHY device. The first element @@ -15,6 +35,7 @@ Optional properties: - phys: from the *Generic PHY* bindings - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" or "usb3-phy". + - resets: a single pair of phandle and reset specifier - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable - snps,disable_scramble_quirk: true when SW should disable data scrambling. Only really useful for FPGA builds. diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt index 472facfa5a71..6087dc7f209e 100644 --- a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -6,12 +6,6 @@ Required properties : - interrupts : Interrupt specifier Optional properties : -- fcs,max-sink-microvolt : Maximum voltage to negotiate when configured as sink -- fcs,max-sink-microamp : Maximum current to negotiate when configured as sink -- fcs,max-sink-microwatt : Maximum power to negotiate when configured as sink - If this is less then max-sink-microvolt * - max-sink-microamp then the configured current will - be clamped. - fcs,operating-sink-microwatt : Minimum amount of power accepted from a sink when negotiating diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt new file mode 100644 index 000000000000..f4633496b122 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt @@ -0,0 +1,45 @@ +HiSilicon STB xHCI + +The device node for HiSilicon STB xHCI host controller + +Required properties: + - compatible: should be "hisilicon,hi3798cv200-xhci" + - reg: specifies physical base address and size of the registers + - interrupts : interrupt used by the controller + - clocks: a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names: must contain + "bus": for bus clock + "utmi": for utmi clock + "pipe": for pipe clock + "suspend": for suspend clock + - resets: a list of phandle and reset specifier pairs as listed in + reset-names property. + - reset-names: must contain + "soft": for soft reset + - phys: a list of phandle + phy specifier pairs + - phy-names: must contain at least one of following: + "inno": for inno phy + "combo": for combo phy + +Optional properties: + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - usb3-lpm-capable: determines if platform is USB3 LPM capable + - imod-interval-ns: default interrupt moderation interval is 40000ns + +Example: + +xhci0: xchi@f98a0000 { + compatible = "hisilicon,hi3798cv200-xhci"; + reg = <0xf98a0000 0x10000>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_USB3_BUS_CLK>, + <&crg HISTB_USB3_UTMI_CLK>, + <&crg HISTB_USB3_PIPE_CLK>, + <&crg HISTB_USB3_SUSPEND_CLK>; + clock-names = "bus", "utmi", "pipe", "suspend"; + resets = <&crg 0xb0 12>; + reset-names = "soft"; + phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>; + phy-names = "inno", "combo"; +}; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt index bc8a2fa5d2bf..95afdcf3c337 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -1,54 +1,95 @@ Qualcomm SuperSpeed DWC3 USB SoC controller Required properties: -- compatible: should contain "qcom,dwc3" +- compatible: Compatible list, contains + "qcom,dwc3" + "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,sdm845-dwc3" for sdm845 SOC. +- reg: Offset and length of register set for QSCRATCH wrapper +- power-domains: specifies a phandle to PM domain provider node - clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock-names -- clock-names: Should contain the following: +- clock-names: Should contain the following: "core" Master/Core clock, have to be >= 125 MHz for SS operation and >= 60MHz for HS operation + "mock_utmi" Mock utmi clock needed for ITP/SOF generation in + host mode. Its frequency should be 19.2MHz. + "sleep" Sleep clock, used for wakeup when USB3 core goes + into low power mode (U3). Optional clocks: - "iface" System bus AXI clock. Not present on all platforms - "sleep" Sleep clock, used when USB3 core goes into low - power mode (U3). + "iface" System bus AXI clock. + Not present on "qcom,msm8996-dwc3" compatible. + "cfg_noc" System Config NOC clock. + Not present on "qcom,msm8996-dwc3" compatible. +- assigned-clocks: Should be: + MOCK_UTMI_CLK + MASTER_CLK +- assigned-clock-rates: Should be: + 19.2Mhz (192000000) for MOCK_UTMI_CLK + >=125Mhz (125000000) for MASTER_CLK in SS mode + >=60Mhz (60000000) for MASTER_CLK in HS mode + +Optional properties: +- resets: Phandle to reset control that resets core and wrapper. +- interrupts: specifies interrupts from controller wrapper used + to wakeup from low power/susepnd state. Must contain + one or more entry for interrupt-names property +- interrupt-names: Must include the following entries: + - "hs_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB2 bus + - "ss_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB3 bus + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate + interrupts for any wakeup event on DM and DP lines +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. + Used when dwc3 operates without SSPHY and only + HS/FS/LS modes are supported. Required child node: A child node must exist to represent the core DWC3 IP block. The name of the node is not important. The content of the node is defined in dwc3.txt. Phy documentation is provided in the following places: -Documentation/devicetree/bindings/phy/qcom-dwc3-usb-phy.txt +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY Example device nodes: hs_phy: phy@100f8800 { - compatible = "qcom,dwc3-hs-usb-phy"; - reg = <0x100f8800 0x30>; - clocks = <&gcc USB30_0_UTMI_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qusb2-v2-phy"; + ... }; ss_phy: phy@100f8830 { - compatible = "qcom,dwc3-ss-usb-phy"; - reg = <0x100f8830 0x30>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "ref"; - #phy-cells = <0>; - + compatible = "qcom,qmp-v3-usb3-phy"; + ... }; - usb3_0: usb30@0 { + usb3_0: usb30@a6f8800 { compatible = "qcom,dwc3"; + reg = <0xa6f8800 0x400>; #address-cells = <1>; #size-cells = <1>; - clocks = <&gcc USB30_0_MASTER_CLK>; - clock-names = "core"; - ranges; + interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "core", "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <133000000>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; dwc3@10000000 { compatible = "snps,dwc3"; diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt new file mode 100644 index 000000000000..09e847e92e5e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt @@ -0,0 +1,17 @@ +Richtek RT1711H TypeC PD Controller. + +Required properties: + - compatible : Must be "richtek,rt1711h". + - reg : Must be 0x4e, it's slave address of RT1711H. + - interrupt-parent : the phandle for the interrupt controller that + provides interrupts for this device. + - interrupts : <a b> where a is the interrupt number and b represents an + encoding of the sense and level information for the interrupt. + +Example : +rt1711h@4e { + compatible = "richtek,rt1711h"; + reg = <0x4e>; + interrupt-parent = <&gpio26>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index c4c00dff4b56..bd1dd316fb23 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -28,7 +28,10 @@ Required properties: - interrupts: one XHCI interrupt should be described here. Optional properties: - - clocks: reference to a clock + - clocks: reference to the clocks + - clock-names: mandatory if there is a second clock, in this case + the name must be "core" for the first clock and "reg" for the + second one - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM - usb3-lpm-capable: determines if platform is USB3 LPM capable - quirk-broken-port-ped: set if the controller has broken port disable mechanism diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index b5f978a4cac6..36003832c2a8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -75,6 +75,7 @@ cnxt Conexant Systems, Inc. compulab CompuLab Ltd. cortina Cortina Systems, Inc. cosmic Cosmic Circuits +crane Crane Connectivity Solutions creative Creative Technology Ltd crystalfontz Crystalfontz America, Inc. cubietech Cubietech, Ltd. @@ -182,6 +183,7 @@ karo Ka-Ro electronics GmbH keithkoep Keith & Koep GmbH keymile Keymile GmbH khadas Khadas +kiebackpeter Kieback & Peter GmbH kinetic Kinetic Technologies kingnovel Kingnovel Technology Co., Ltd. kosagi Sutajio Ko-Usagi PTE Ltd. |