diff options
Diffstat (limited to 'Documentation/devicetree')
100 files changed, 2505 insertions, 116 deletions
diff --git a/Documentation/devicetree/bindings/arc/archs-pct.txt b/Documentation/devicetree/bindings/arc/archs-pct.txt new file mode 100644 index 000000000000..1ae98b87c640 --- /dev/null +++ b/Documentation/devicetree/bindings/arc/archs-pct.txt @@ -0,0 +1,17 @@ +* ARC HS Performance Counters + +The ARC HS can be configured with a pipeline performance monitor for counting +CPU and cache events like cache misses and hits. Like conventional PCT there +are 100+ hardware conditions dynamically mapped to upto 32 counters. +It also supports overflow interrupts. + +Required properties: + +- compatible : should contain + "snps,archs-pct" + +Example: + +pmu { + compatible = "snps,archs-pct"; +}; diff --git a/Documentation/devicetree/bindings/arm/atmel-at91.txt b/Documentation/devicetree/bindings/arm/atmel-at91.txt index 424ac8cbfa08..7fd64ec9ee1d 100644 --- a/Documentation/devicetree/bindings/arm/atmel-at91.txt +++ b/Documentation/devicetree/bindings/arm/atmel-at91.txt @@ -27,6 +27,8 @@ compatible: must be one of: o "atmel,at91sam9xe" * "atmel,sama5" for SoCs using a Cortex-A5, shall be extended with the specific SoC family: + o "atmel,sama5d2" shall be extended with the specific SoC compatible: + - "atmel,sama5d27" o "atmel,sama5d3" shall be extended with the specific SoC compatible: - "atmel,sama5d31" - "atmel,sama5d33" @@ -50,6 +52,7 @@ System Timer (ST) required properties: - reg: Should contain registers location and length - interrupts: Should contain interrupt for the ST which is the IRQ line shared across all System Controller members. +- clocks: phandle to input clock. Its subnodes can be: - watchdog: compatible should be "atmel,at91rm9200-wdt" @@ -61,7 +64,7 @@ TC/TCLIB Timer required properties: Note that you can specify several interrupt cells if the TC block has one interrupt per channel. - clock-names: tuple listing input clock names. - Required elements: "t0_clk" + Required elements: "t0_clk", "slow_clk" Optional elements: "t1_clk", "t2_clk" - clocks: phandles to input clocks. @@ -87,14 +90,16 @@ One interrupt per TC channel in a TC block: RSTC Reset Controller required properties: - compatible: Should be "atmel,<chip>-rstc". - <chip> can be "at91sam9260" or "at91sam9g45" + <chip> can be "at91sam9260" or "at91sam9g45" or "sama5d3" - reg: Should contain registers location and length +- clocks: phandle to input clock. Example: rstc@fffffd00 { compatible = "atmel,at91sam9260-rstc"; reg = <0xfffffd00 0x10>; + clocks = <&clk32k>; }; RAMC SDRAM/DDR Controller required properties: @@ -117,6 +122,7 @@ required properties: - compatible: Should be "atmel,<chip>-shdwc". <chip> can be "at91sam9260", "at91sam9rl" or "at91sam9x5". - reg: Should contain registers location and length +- clocks: phandle to input clock. optional properties: - atmel,wakeup-mode: String, operation mode of the wakeup mode. @@ -135,9 +141,10 @@ optional at91sam9x5 properties: Example: - rstc@fffffd00 { - compatible = "atmel,at91sam9260-rstc"; - reg = <0xfffffd00 0x10>; + shdwc@fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + clocks = <&clk32k>; }; Special Function Registers (SFR) diff --git a/Documentation/devicetree/bindings/arm/bcm/ns2.txt b/Documentation/devicetree/bindings/arm/bcm/ns2.txt new file mode 100644 index 000000000000..35f056f4a1c3 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/ns2.txt @@ -0,0 +1,9 @@ +Broadcom North Star 2 (NS2) device tree bindings +------------------------------------------------ + +Boards with NS2 shall have the following properties: + +Required root node property: + +NS2 SVK board +compatible = "brcm,ns2-svk", "brcm,ns2"; diff --git a/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.txt b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.txt new file mode 100644 index 000000000000..6824b3180ffb --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/raspberrypi,bcm2835-firmware.txt @@ -0,0 +1,14 @@ +Raspberry Pi VideoCore firmware driver + +Required properties: + +- compatible: Should be "raspberrypi,bcm2835-firmware" +- mboxes: Phandle to the firmware device's Mailbox. + (See: ../mailbox/mailbox.txt for more information) + +Example: + +firmware { + compatible = "raspberrypi,bcm2835-firmware"; + mboxes = <&mailbox>; +}; diff --git a/Documentation/devicetree/bindings/arm/coresight.txt b/Documentation/devicetree/bindings/arm/coresight.txt index 65a6db2271a2..62938eb9697f 100644 --- a/Documentation/devicetree/bindings/arm/coresight.txt +++ b/Documentation/devicetree/bindings/arm/coresight.txt @@ -17,6 +17,7 @@ its hardware characteristcs. - "arm,coresight-tmc", "arm,primecell"; - "arm,coresight-funnel", "arm,primecell"; - "arm,coresight-etm3x", "arm,primecell"; + - "arm,coresight-etm4x", "arm,primecell"; - "qcom,coresight-replicator1x", "arm,primecell"; * reg: physical base address and length of the register diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index d6b794cef0b8..91e6e5c478d0 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -199,6 +199,7 @@ nodes to be present and contain the properties described below. "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" "rockchip,rk3066-smp" + "ste,dbx500-smp" - cpu-release-addr Usage: required for systems that have an "enable-method" diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt index c431c67524d6..c733e28e18e5 100644 --- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt +++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt @@ -127,6 +127,24 @@ Example: #clock-cells = <1>; }; + +Hisilicon Hi6220 SRAM controller + +Required properties: +- compatible : "hisilicon,hi6220-sramctrl", "syscon" +- reg : Register address and size + +Hisilicon's SoCs use sram for multiple purpose; on Hi6220 there have several +SRAM banks for power management, modem, security, etc. Further, use "syscon" +managing the common sram which can be shared by multiple modules. + +Example: + /*for Hi6220*/ + sram: sram@fff80000 { + compatible = "hisilicon,hi6220-sramctrl", "syscon"; + reg = <0x0 0xfff80000 0x0 0x12000>; + }; + ----------------------------------------------------------------------- Hisilicon HiP01 system controller diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt index 4f40ff3fee4b..5171ad8f48ff 100644 --- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt +++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt @@ -20,6 +20,8 @@ And in addition, the compatible shall be extended with the specific board. Currently known boards are: "buffalo,lschlv2" +"buffalo,lswvl" +"buffalo,lswxl" "buffalo,lsxhl" "buffalo,lsxl" "dlink,dns-320" diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt index dd7550a29db6..618a91994a18 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.txt +++ b/Documentation/devicetree/bindings/arm/mediatek.txt @@ -1,12 +1,15 @@ -MediaTek mt65xx & mt81xx Platforms Device Tree Bindings +MediaTek mt65xx, mt67xx & mt81xx Platforms Device Tree Bindings -Boards with a MediaTek mt65xx/mt81xx SoC shall have the following property: +Boards with a MediaTek mt65xx/mt67xx/mt81xx SoC shall have the +following property: Required root node property: compatible: Must contain one of + "mediatek,mt6580" "mediatek,mt6589" "mediatek,mt6592" + "mediatek,mt6795" "mediatek,mt8127" "mediatek,mt8135" "mediatek,mt8173" @@ -14,12 +17,18 @@ compatible: Must contain one of Supported boards: +- Evaluation board for MT6580: + Required root node properties: + - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580"; - bq Aquaris5 smart phone: Required root node properties: - compatible = "mundoreader,bq-aquaris5", "mediatek,mt6589"; - Evaluation board for MT6592: Required root node properties: - compatible = "mediatek,mt6592-evb", "mediatek,mt6592"; +- Evaluation board for MT6795(Helio X10): + Required root node properties: + - compatible = "mediatek,mt6795-evb", "mediatek,mt6795"; - MTK mt8127 tablet moose EVB: Required root node properties: - compatible = "mediatek,mt8127-moose", "mediatek,mt8127"; diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt index 4f5a5352ccd8..afef6a85ac51 100644 --- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt +++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,sysirq.txt @@ -1,4 +1,4 @@ -Mediatek 65xx/81xx sysirq ++Mediatek 65xx/67xx/81xx sysirq Mediatek SOCs sysirq support controllable irq inverter for each GIC SPI interrupt. @@ -8,9 +8,11 @@ Required properties: "mediatek,mt8173-sysirq" "mediatek,mt8135-sysirq" "mediatek,mt8127-sysirq" + "mediatek,mt6795-sysirq" "mediatek,mt6592-sysirq" "mediatek,mt6589-sysirq" "mediatek,mt6582-sysirq" + "mediatek,mt6580-sysirq" "mediatek,mt6577-sysirq" - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Use the same format as specified by GIC in diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 4f6a82cef1d1..9f4e5136e568 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -135,6 +135,9 @@ Boards: - AM335X OrionLXm : Substation Automation Platform compatible = "novatech,am335x-lxm", "ti,am33xx" +- AM335X phyBOARD-WEGA: Single Board Computer dev kit + compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt index 60d4a1e0a9b5..af58cd74aeff 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.txt +++ b/Documentation/devicetree/bindings/arm/rockchip.txt @@ -26,3 +26,38 @@ Rockchip platforms device tree bindings - ChipSPARK PopMetal-RK3288 board: Required root node properties: - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288"; + +- Netxeon R89 board: + Required root node properties: + - compatible = "netxeon,r89", "rockchip,rk3288"; + +- Google Jerry (Hisense Chromebook C11 and more): + Required root node properties: + - compatible = "google,veyron-jerry-rev7", "google,veyron-jerry-rev6", + "google,veyron-jerry-rev5", "google,veyron-jerry-rev4", + "google,veyron-jerry-rev3", "google,veyron-jerry", + "google,veyron", "rockchip,rk3288"; + +- Google Minnie (Asus Chromebook Flip C100P): + Required root node properties: + - compatible = "google,veyron-minnie-rev4", "google,veyron-minnie-rev3", + "google,veyron-minnie-rev2", "google,veyron-minnie-rev1", + "google,veyron-minnie-rev0", "google,veyron-minnie", + "google,veyron", "rockchip,rk3288"; + +- Google Pinky (dev-board): + Required root node properties: + - compatible = "google,veyron-pinky-rev2", "google,veyron-pinky", + "google,veyron", "rockchip,rk3288"; + +- Google Speedy (Asus C201 Chromebook): + Required root node properties: + - compatible = "google,veyron-speedy-rev9", "google,veyron-speedy-rev8", + "google,veyron-speedy-rev7", "google,veyron-speedy-rev6", + "google,veyron-speedy-rev5", "google,veyron-speedy-rev4", + "google,veyron-speedy-rev3", "google,veyron-speedy-rev2", + "google,veyron-speedy", "google,veyron", "rockchip,rk3288"; + +- Rockchip R88 board: + Required root node properties: + - compatible = "rockchip,r88", "rockchip,rk3368"; diff --git a/Documentation/devicetree/bindings/arm/sp810.txt b/Documentation/devicetree/bindings/arm/sp810.txt new file mode 100644 index 000000000000..6808fb5dee40 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/sp810.txt @@ -0,0 +1,46 @@ +SP810 System Controller +----------------------- + +Required properties: + +- compatible: standard compatible string for a Primecell peripheral, + see Documentation/devicetree/bindings/arm/primecell.txt + for more details + should be: "arm,sp810", "arm,primecell" + +- reg: standard registers property, physical address and size + of the control registers + +- clock-names: from the common clock bindings, for more details see + Documentation/devicetree/bindings/clock/clock-bindings.txt; + should be: "refclk", "timclk", "apb_pclk" + +- clocks: from the common clock bindings, phandle and clock + specifier pairs for the entries of clock-names property + +- #clock-cells: from the common clock bindings; + should be: <1> + +- clock-output-names: from the common clock bindings; + should be: "timerclken0", "timerclken1", "timerclken2", "timerclken3" + +- assigned-clocks: from the common clock binding; + should be: clock specifier for each output clock of this + provider node + +- assigned-clock-parents: from the common clock binding; + should be: phandle of input clock listed in clocks + property with the highest frequency + +Example: + v2m_sysctl: sysctl@020000 { + compatible = "arm,sp810", "arm,primecell"; + reg = <0x020000 0x1000>; + clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; + clock-names = "refclk", "timclk", "apb_pclk"; + #clock-cells = <1>; + clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; + assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; + assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; + + }; diff --git a/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt b/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt new file mode 100644 index 000000000000..2be1e038ca62 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt @@ -0,0 +1,19 @@ +Binding for simple gpio clock multiplexer. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "gpio-mux-clock". +- clocks: list of two references to parent clocks. +- #clock-cells : from common clock binding; shall be set to 0. +- select-gpios : GPIO reference for selecting the parent clock. + +Example: + clock { + compatible = "gpio-mux-clock"; + clocks = <&parentclk1>, <&parentclk2>; + #clock-cells = <0>; + select-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt index 259e30af9597..e4d5feaebc29 100644 --- a/Documentation/devicetree/bindings/clock/hi6220-clock.txt +++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt @@ -15,19 +15,36 @@ Required Properties: - "hisilicon,hi6220-sysctrl" - "hisilicon,hi6220-mediactrl" - "hisilicon,hi6220-pmctrl" + - "hisilicon,hi6220-stub-clk" - reg: physical base address of the controller and length of memory mapped region. - #clock-cells: should be 1. -For example: +Optional Properties: + +- hisilicon,hi6220-clk-sram: phandle to the syscon managing the SoC internal sram; + the driver need use the sram to pass parameters for frequency change. + +- mboxes: use the label reference for the mailbox as the first parameter, the + second parameter is the channel number. + +Example 1: sys_ctrl: sys_ctrl@f7030000 { compatible = "hisilicon,hi6220-sysctrl", "syscon"; reg = <0x0 0xf7030000 0x0 0x2000>; #clock-cells = <1>; }; +Example 2: + stub_clock: stub_clock { + compatible = "hisilicon,hi6220-stub-clk"; + hisilicon,hi6220-clk-sram = <&sram>; + #clock-cells = <1>; + mboxes = <&mailbox 1>; + }; + Each clock is assigned an identifier and client nodes use this identifier to specify the clock which they consume. diff --git a/Documentation/devicetree/bindings/clock/imx6ul-clock.txt b/Documentation/devicetree/bindings/clock/imx6ul-clock.txt new file mode 100644 index 000000000000..571d5039f663 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6ul-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 UltraLite + +Required properties: +- compatible: Should be "fsl,imx6ul-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6ul-clock.h +for the full list of i.MX6 UltraLite clock IDs. diff --git a/Documentation/devicetree/bindings/clock/mt8173-cpu-dvfs.txt b/Documentation/devicetree/bindings/clock/mt8173-cpu-dvfs.txt new file mode 100644 index 000000000000..52b457c23eed --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mt8173-cpu-dvfs.txt @@ -0,0 +1,83 @@ +Device Tree Clock bindins for CPU DVFS of Mediatek MT8173 SoC + +Required properties: +- clocks: A list of phandle + clock-specifier pairs for the clocks listed in clock names. +- clock-names: Should contain the following: + "cpu" - The multiplexer for clock input of CPU cluster. + "intermediate" - A parent of "cpu" clock which is used as "intermediate" clock + source (usually MAINPLL) when the original CPU PLL is under + transition and not stable yet. + Please refer to Documentation/devicetree/bindings/clk/clock-bindings.txt for + generic clock consumer properties. +- proc-supply: Regulator for Vproc of CPU cluster. + +Optional properties: +- sram-supply: Regulator for Vsram of CPU cluster. When present, the cpufreq driver + needs to do "voltage tracking" to step by step scale up/down Vproc and + Vsram to fit SoC specific needs. When absent, the voltage scaling + flow is handled by hardware, hence no software "voltage tracking" is + needed. + +Example: +-------- + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x000>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA53SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + }; + + cpu1: cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x001>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA53SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + }; + + cpu2: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x100>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA57SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + }; + + cpu3: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a57"; + reg = <0x101>; + enable-method = "psci"; + cpu-idle-states = <&CPU_SLEEP_0>; + clocks = <&infracfg CLK_INFRA_CA57SEL>, + <&apmixedsys CLK_APMIXED_MAINPLL>; + clock-names = "cpu", "intermediate"; + }; + + &cpu0 { + proc-supply = <&mt6397_vpca15_reg>; + }; + + &cpu1 { + proc-supply = <&mt6397_vpca15_reg>; + }; + + &cpu2 { + proc-supply = <&da9211_vcpu_reg>; + sram-supply = <&mt6397_vsramca7_reg>; + }; + + &cpu3 { + proc-supply = <&da9211_vcpu_reg>; + sram-supply = <&mt6397_vsramca7_reg>; + }; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt new file mode 100644 index 000000000000..ee7e5fd4a50b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -0,0 +1,79 @@ +NVIDIA Tegra124 DFLL FCPU clocksource + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The DFLL IP block on Tegra is a root clocksource designed for clocking +the fast CPU cluster. It consists of a free-running voltage controlled +oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop +control module that will automatically adjust the VDD_CPU voltage by +communicating with an off-chip PMIC either via an I2C bus or via PWM signals. +Currently only the I2C mode is supported by these bindings. + +Required properties: +- compatible : should be "nvidia,tegra124-dfll" +- reg : Defines the following set of registers, in the order listed: + - registers for the DFLL control logic. + - registers for the I2C output logic. + - registers for the integrated I2C master controller. + - look-up table RAM for voltage register values. +- interrupts: Should contain the DFLL block interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See clock-bindings.txt for details. +- clock-names: Must include the following entries: + - soc: Clock source for the DFLL control logic. + - ref: The closed loop reference clock + - i2c: Clock source for the integrated I2C master. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - dvco: Reset control for the DFLL DVCO. +- #clock-cells: Must be 0. +- clock-output-names: Name of the clock output. +- vdd-cpu-supply: Regulator for the CPU voltage rail that the DFLL + hardware will start controlling. The regulator will be queried for + the I2C register, control values and supported voltages. + +Required properties for the control loop parameters: +- nvidia,sample-rate: Sample rate of the DFLL control loop. +- nvidia,droop-ctrl: See the register CL_DVFS_DROOP_CTRL in the TRM. +- nvidia,force-mode: See the field DFLL_PARAMS_FORCE_MODE in the TRM. +- nvidia,cf: Numeric value, see the field DFLL_PARAMS_CF_PARAM in the TRM. +- nvidia,ci: Numeric value, see the field DFLL_PARAMS_CI_PARAM in the TRM. +- nvidia,cg: Numeric value, see the field DFLL_PARAMS_CG_PARAM in the TRM. + +Optional properties for the control loop parameters: +- nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM. + +Required properties for I2C mode: +- nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode. + +Example: + +clock@0,70110000 { + compatible = "nvidia,tegra124-dfll"; + reg = <0 0x70110000 0 0x100>, /* DFLL control */ + <0 0x70110000 0 0x100>, /* I2C output control */ + <0 0x70110100 0 0x100>, /* Integrated I2C controller */ + <0 0x70110200 0 0x100>; /* Look-up table RAM */ + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DFLL_SOC>, + <&tegra_car TEGRA124_CLK_DFLL_REF>, + <&tegra_car TEGRA124_CLK_I2C5>; + clock-names = "soc", "ref", "i2c"; + resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>; + reset-names = "dvco"; + #clock-cells = <0>; + clock-output-names = "dfllCPU_out"; + vdd-cpu-supply = <&vdd_cpu>; + status = "okay"; + + nvidia,sample-rate = <12500>; + nvidia,droop-ctrl = <0x00000f00>; + nvidia,force-mode = <1>; + nvidia,cf = <10>; + nvidia,ci = <0>; + nvidia,cg = <2>; + + nvidia,i2c-fs-rate = <400000>; +}; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt index 2f3747fdcf1c..e4cdaf1cb333 100644 --- a/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt @@ -1,7 +1,9 @@ * Renesas R8A7778 Clock Pulse Generator (CPG) The CPG generates core clocks for the R8A7778. It includes two PLLs and -several fixed ratio dividers +several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. Required Properties: @@ -10,10 +12,18 @@ Required Properties: - #clock-cells: Must be 1 - clock-output-names: The names of the clocks. Supported clocks are "plla", "pllb", "b", "out", "p", "s", and "s1". + - #power-domain-cells: Must be 0 +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. -Example -------- + +Examples +-------- + + - CPG device node: cpg_clocks: cpg_clocks@ffc80000 { compatible = "renesas,r8a7778-cpg-clocks"; @@ -22,4 +32,17 @@ Example clocks = <&extal_clk>; clock-output-names = "plla", "pllb", "b", "out", "p", "s", "s1"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + sdhi0: sd@ffe4c000 { + compatible = "renesas,sdhi-r8a7778"; + reg = <0xffe4c000 0x100>; + interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7778_CLK_SDHI0>; + power-domains = <&cpg_clocks>; + status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt index ed3c8cb12f4e..8c81547c29f5 100644 --- a/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt @@ -1,7 +1,9 @@ * Renesas R8A7779 Clock Pulse Generator (CPG) The CPG generates core clocks for the R8A7779. It includes one PLL and -several fixed ratio dividers +several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. Required Properties: @@ -12,16 +14,36 @@ Required Properties: - #clock-cells: Must be 1 - clock-output-names: The names of the clocks. Supported clocks are "plla", "z", "zs", "s", "s1", "p", "b", "out". + - #power-domain-cells: Must be 0 +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. -Example -------- + +Examples +-------- + + - CPG device node: cpg_clocks: cpg_clocks@ffc80000 { compatible = "renesas,r8a7779-cpg-clocks"; - reg = <0 0xffc80000 0 0x30>; + reg = <0xffc80000 0x30>; clocks = <&extal_clk>; #clock-cells = <1>; clock-output-names = "plla", "z", "zs", "s", "s1", "p", "b", "out"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + sata: sata@fc600000 { + compatible = "renesas,sata-r8a7779", "renesas,rcar-sata"; + reg = <0xfc600000 0x2000>; + interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7779_CLK_SATA>; + power-domains = <&cpg_clocks>; }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt index 56f111bd3e45..2a9a8edc8f35 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -2,6 +2,8 @@ The CPG generates core clocks for the R-Car Gen2 SoCs. It includes three PLLs and several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. Required Properties: @@ -20,10 +22,18 @@ Required Properties: - clock-output-names: The names of the clocks. Supported clocks are "main", "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", "z", "rcan", and "adsp" + - #power-domain-cells: Must be 0 +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. -Example -------- + +Examples +-------- + + - CPG device node: cpg_clocks: cpg_clocks@e6150000 { compatible = "renesas,r8a7790-cpg-clocks", @@ -34,4 +44,16 @@ Example clock-output-names = "main", "pll0, "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", "z", "rcan", "adsp"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + thermal@e61f0000 { + compatible = "renesas,thermal-r8a7790", "renesas,rcar-thermal"; + reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7790_CLK_THERMAL>; + power-domains = <&cpg_clocks>; }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt index b0f7ddb8cdb1..bb51a33a1fbf 100644 --- a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt +++ b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt @@ -2,6 +2,8 @@ The CPG generates core clocks for the RZ SoCs. It includes the PLL, variable CPU and GPU clocks, and several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. Required Properties: @@ -14,10 +16,18 @@ Required Properties: - #clock-cells: Must be 1 - clock-output-names: The names of the clocks. Supported clocks are "pll", "i", and "g" + - #power-domain-cells: Must be 0 +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. -Example -------- + +Examples +-------- + + - CPG device node: cpg_clocks: cpg_clocks@fcfe0000 { #clock-cells = <1>; @@ -26,4 +36,19 @@ Example reg = <0xfcfe0000 0x18>; clocks = <&extal_clk>, <&usb_x1_clk>; clock-output-names = "pll", "i", "g"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + mtu2: timer@fcff0000 { + compatible = "renesas,mtu2-r7s72100", "renesas,mtu2"; + reg = <0xfcff0000 0x400>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tgi0a"; + clocks = <&mstp3_clks R7S72100_CLK_MTU2>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + status = "disabled"; }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt new file mode 100644 index 000000000000..7c8bbcfed8d2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3368 Clock and Reset Unit + +The RK3368 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3368-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing, pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3368-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_gmac" - external GMAC clock - optional + - "ext_hsadc" - external HSADC clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + - "ext_vip" - external VIP clock - optional, + - "usbotg_out" - output clock of the pll in the otg phy + +Example: Clock controller node: + + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3368-cru"; + reg = <0x0 0xff760000 0x0 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt index efb51cf0c845..d8b168ebd5f1 100644 --- a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -21,8 +21,8 @@ Required properties: "st,stih416-plls-c32-ddr", "st,clkgen-plls-c32" "st,stih407-plls-c32-a0", "st,clkgen-plls-c32" "st,stih407-plls-c32-a9", "st,clkgen-plls-c32" - "st,stih407-plls-c32-c0_0", "st,clkgen-plls-c32" - "st,stih407-plls-c32-c0_1", "st,clkgen-plls-c32" + "sst,plls-c32-cx_0", "st,clkgen-plls-c32" + "sst,plls-c32-cx_1", "st,clkgen-plls-c32" "st,stih415-gpu-pll-c32", "st,clkgengpu-pll-c32" "st,stih416-gpu-pll-c32", "st,clkgengpu-pll-c32" diff --git a/Documentation/devicetree/bindings/clock/ux500.txt b/Documentation/devicetree/bindings/clock/ux500.txt new file mode 100644 index 000000000000..e52bd4b72348 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ux500.txt @@ -0,0 +1,64 @@ +Clock bindings for ST-Ericsson Ux500 clocks + +Required properties : +- compatible : shall contain only one of the following: + "stericsson,u8500-clks" + "stericsson,u8540-clks" + "stericsson,u9540-clks" +- reg : shall contain base register location and length for + CLKRST1, 2, 3, 5, and 6 in an array. Note the absence of + CLKRST4, which does not exist. + +Required subnodes: +- prcmu-clock: a subnode with one clock cell for PRCMU (power, + reset, control unit) clocks. The cell indicates which PRCMU + clock in the prcmu-clock node the consumer wants to use. +- prcc-periph-clock: a subnode with two clock cells for + PRCC (programmable reset- and clock controller) peripheral clocks. + The first cell indicates which PRCC block the consumer + wants to use, possible values are 1, 2, 3, 5, 6. The second + cell indicates which clock inside the PRCC block it wants, + possible values are 0 thru 31. +- prcc-kernel-clock: a subnode with two clock cells for + PRCC (programmable reset- and clock controller) kernel clocks + The first cell indicates which PRCC block the consumer + wants to use, possible values are 1, 2, 3, 5, 6. The second + cell indicates which clock inside the PRCC block it wants, + possible values are 0 thru 31. +- rtc32k-clock: a subnode with zero clock cells for the 32kHz + RTC clock. +- smp-twd-clock: a subnode for the ARM SMP Timer Watchdog cluster + with zero clock cells. + +Example: + +clocks { + compatible = "stericsson,u8500-clks"; + /* + * Registers for the CLKRST block on peripheral + * groups 1, 2, 3, 5, 6, + */ + reg = <0x8012f000 0x1000>, <0x8011f000 0x1000>, + <0x8000f000 0x1000>, <0xa03ff000 0x1000>, + <0xa03cf000 0x1000>; + + prcmu_clk: prcmu-clock { + #clock-cells = <1>; + }; + + prcc_pclk: prcc-periph-clock { + #clock-cells = <2>; + }; + + prcc_kclk: prcc-kernel-clock { + #clock-cells = <2>; + }; + + rtc_clk: rtc32k-clock { + #clock-cells = <0>; + }; + + smp_twd_clk: smp-twd-clock { + #clock-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt b/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt new file mode 100644 index 000000000000..b1669fbfb740 --- /dev/null +++ b/Documentation/devicetree/bindings/cpufreq/tegra124-cpufreq.txt @@ -0,0 +1,44 @@ +Tegra124 CPU frequency scaling driver bindings +---------------------------------------------- + +Both required and optional properties listed below must be defined +under node /cpus/cpu@0. + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - cpu_g: Clock mux for the fast CPU cluster. + - cpu_lp: Clock mux for the low-power CPU cluster. + - pll_x: Fast PLL clocksource. + - pll_p: Auxiliary PLL used during fast PLL rate changes. + - dfll: Fast DFLL clocksource that also automatically scales CPU voltage. +- vdd-cpu-supply: Regulator for CPU voltage + +Optional properties: +- clock-latency: Specify the possible maximum transition latency for clock, + in unit of nanoseconds. + +Example: +-------- +cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0>; + + clocks = <&tegra_car TEGRA124_CLK_CCLK_G>, + <&tegra_car TEGRA124_CLK_CCLK_LP>, + <&tegra_car TEGRA124_CLK_PLL_X>, + <&tegra_car TEGRA124_CLK_PLL_P>, + <&dfll>; + clock-names = "cpu_g", "cpu_lp", "pll_x", "pll_p", "dfll"; + clock-latency = <300000>; + vdd-cpu-supply: <&vdd_cpu>; + }; + + <...> +}; diff --git a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt index e4022776ac6e..6831d025ec24 100644 --- a/Documentation/devicetree/bindings/crypto/fsl-sec4.txt +++ b/Documentation/devicetree/bindings/crypto/fsl-sec4.txt @@ -106,6 +106,18 @@ PROPERTIES to the interrupt parent to which the child domain is being mapped. + - clocks + Usage: required if SEC 4.0 requires explicit enablement of clocks + Value type: <prop_encoded-array> + Definition: A list of phandle and clock specifier pairs describing + the clocks required for enabling and disabling SEC 4.0. + + - clock-names + Usage: required if SEC 4.0 requires explicit enablement of clocks + Value type: <string> + Definition: A list of clock name strings in the same order as the + clocks property. + Note: All other standard properties (see the ePAPR) are allowed but are optional. @@ -120,6 +132,11 @@ EXAMPLE ranges = <0 0x300000 0x10000>; interrupt-parent = <&mpic>; interrupts = <92 2>; + clocks = <&clks IMX6QDL_CLK_CAAM_MEM>, + <&clks IMX6QDL_CLK_CAAM_ACLK>, + <&clks IMX6QDL_CLK_CAAM_IPG>, + <&clks IMX6QDL_CLK_EIM_SLOW>; + clock-names = "mem", "aclk", "ipg", "emi_slow"; }; ===================================================================== @@ -288,12 +305,13 @@ Secure Non-Volatile Storage (SNVS) Node Node defines address range and the associated interrupt for the SNVS function. This function monitors security state information & reports - security violations. + security violations. This also included rtc, + system power off and ON/OFF key. - compatible Usage: required Value type: <string> - Definition: Must include "fsl,sec-v4.0-mon". + Definition: Must include "fsl,sec-v4.0-mon" and "syscon". - reg Usage: required @@ -324,7 +342,7 @@ Secure Non-Volatile Storage (SNVS) Node the child address, parent address, & length. - interrupts - Usage: required + Usage: optional Value type: <prop_encoded-array> Definition: Specifies the interrupts generated by this device. The value of the interrupts property @@ -341,7 +359,7 @@ Secure Non-Volatile Storage (SNVS) Node EXAMPLE sec_mon@314000 { - compatible = "fsl,sec-v4.0-mon"; + compatible = "fsl,sec-v4.0-mon", "syscon"; reg = <0x314000 0x1000>; ranges = <0 0x314000 0x1000>; interrupt-parent = <&mpic>; @@ -358,16 +376,72 @@ Secure Non-Volatile Storage (SNVS) Low Power (LP) RTC Node Value type: <string> Definition: Must include "fsl,sec-v4.0-mon-rtc-lp". - - reg + - interrupts Usage: required - Value type: <prop-encoded-array> - Definition: A standard property. Specifies the physical - address and length of the SNVS LP configuration registers. + Value type: <prop_encoded-array> + Definition: Specifies the interrupts generated by this + device. The value of the interrupts property + consists of one interrupt specifier. The format + of the specifier is defined by the binding document + describing the node's interrupt parent. + + - regmap + Usage: required + Value type: <phandle> + Definition: this is phandle to the register map node. + + - offset + Usage: option + value type: <u32> + Definition: LP register offset. default it is 0x34. EXAMPLE - sec_mon_rtc_lp@314000 { + sec_mon_rtc_lp@1 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; - reg = <0x34 0x58>; + interrupts = <93 2>; + regmap = <&snvs>; + offset = <0x34>; + }; + +===================================================================== +System ON/OFF key driver + + The snvs-pwrkey is designed to enable POWER key function which controlled + by SNVS ONOFF, the driver can report the status of POWER key and wakeup + system if pressed after system suspend. + + - compatible: + Usage: required + Value type: <string> + Definition: Mush include "fsl,sec-v4.0-pwrkey". + + - interrupts: + Usage: required + Value type: <prop_encoded-array> + Definition: The SNVS ON/OFF interrupt number to the CPU(s). + + - linux,keycode: + Usage: option + Value type: <int> + Definition: Keycode to emit, KEY_POWER by default. + + - wakeup-source: + Usage: option + Value type: <boo> + Definition: Button can wake-up the system. + + - regmap: + Usage: required: + Value type: <phandle> + Definition: this is phandle to the register map node. + +EXAMPLE: + snvs-pwrkey@0x020cc000 { + compatible = "fsl,sec-v4.0-pwrkey"; + regmap = <&snvs>; + interrupts = <0 4 0x4> + linux,keycode = <116>; /* KEY_POWER */ + wakeup; }; ===================================================================== @@ -443,12 +517,20 @@ FULL EXAMPLE compatible = "fsl,sec-v4.0-mon"; reg = <0x314000 0x1000>; ranges = <0 0x314000 0x1000>; - interrupt-parent = <&mpic>; - interrupts = <93 2>; sec_mon_rtc_lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; - reg = <0x34 0x58>; + regmap = <&sec_mon>; + offset = <0x34>; + interrupts = <93 2>; + }; + + snvs-pwrkey@0x020cc000 { + compatible = "fsl,sec-v4.0-pwrkey"; + regmap = <&sec_mon>; + interrupts = <0 4 0x4>; + linux,keycode = <116>; /* KEY_POWER */ + wakeup; }; }; diff --git a/Documentation/devicetree/bindings/crypto/sun4i-ss.txt b/Documentation/devicetree/bindings/crypto/sun4i-ss.txt new file mode 100644 index 000000000000..5d38e9b7033f --- /dev/null +++ b/Documentation/devicetree/bindings/crypto/sun4i-ss.txt @@ -0,0 +1,23 @@ +* Allwinner Security System found on A20 SoC + +Required properties: +- compatible : Should be "allwinner,sun4i-a10-crypto". +- reg: Should contain the Security System register location and length. +- interrupts: Should contain the IRQ line for the Security System. +- clocks : List of clock specifiers, corresponding to ahb and ss. +- clock-names : Name of the functional clock, should be + * "ahb" : AHB gating clock + * "mod" : SS controller clock + +Optional properties: + - resets : phandle + reset specifier pair + - reset-names : must contain "ahb" + +Example: + crypto: crypto-engine@01c15000 { + compatible = "allwinner,sun4i-a10-crypto"; + reg = <0x01c15000 0x1000>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ahb_gates 5>, <&ss_clk>; + clock-names = "ahb", "mod"; + }; diff --git a/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt index b54bf3a2ff57..3e36c1d11386 100644 --- a/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt +++ b/Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt @@ -11,15 +11,14 @@ to various devfreq devices. The devfreq devices would use the event data when derterming the current state of each IP. Required properties: -- compatible: Should be "samsung,exynos-ppmu". +- compatible: Should be "samsung,exynos-ppmu" or "samsung,exynos-ppmu-v2. - reg: physical base address of each PPMU and length of memory mapped region. Optional properties: - clock-names : the name of clock used by the PPMU, "ppmu" - clocks : phandles for clock specified in "clock-names" property -- #clock-cells: should be 1. -Example1 : PPMU nodes in exynos3250.dtsi are listed below. +Example1 : PPMUv1 nodes in exynos3250.dtsi are listed below. ppmu_dmc0: ppmu_dmc0@106a0000 { compatible = "samsung,exynos-ppmu"; @@ -108,3 +107,41 @@ Example2 : Events of each PPMU node in exynos3250-rinato.dts are listed below. }; }; }; + +Example3 : PPMUv2 nodes in exynos5433.dtsi are listed below. + + ppmu_d0_cpu: ppmu_d0_cpu@10480000 { + compatible = "samsung,exynos-ppmu-v2"; + reg = <0x10480000 0x2000>; + status = "disabled"; + }; + + ppmu_d0_general: ppmu_d0_general@10490000 { + compatible = "samsung,exynos-ppmu-v2"; + reg = <0x10490000 0x2000>; + status = "disabled"; + }; + + ppmu_d0_rt: ppmu_d0_rt@104a0000 { + compatible = "samsung,exynos-ppmu-v2"; + reg = <0x104a0000 0x2000>; + status = "disabled"; + }; + + ppmu_d1_cpu: ppmu_d1_cpu@104b0000 { + compatible = "samsung,exynos-ppmu-v2"; + reg = <0x104b0000 0x2000>; + status = "disabled"; + }; + + ppmu_d1_general: ppmu_d1_general@104c0000 { + compatible = "samsung,exynos-ppmu-v2"; + reg = <0x104c0000 0x2000>; + status = "disabled"; + }; + + ppmu_d1_rt: ppmu_d1_rt@104d0000 { + compatible = "samsung,exynos-ppmu-v2"; + reg = <0x104d0000 0x2000>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-palmas.txt b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt index 45414bbcd945..f61d5af44a27 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-palmas.txt +++ b/Documentation/devicetree/bindings/extcon/extcon-palmas.txt @@ -10,8 +10,11 @@ Required Properties: Optional Properties: - ti,wakeup : To enable the wakeup comparator in probe - - ti,enable-id-detection: Perform ID detection. + - ti,enable-id-detection: Perform ID detection. If id-gpio is specified + it performs id-detection using GPIO else using OTG core. - ti,enable-vbus-detection: Perform VBUS detection. + - id-gpio: gpio for GPIO ID detection. See gpio binding. + - debounce-delay-ms: debounce delay for GPIO ID pin in milliseconds. palmas-usb { compatible = "ti,twl6035-usb", "ti,palmas-usb"; diff --git a/Documentation/devicetree/bindings/hwmon/lm70.txt b/Documentation/devicetree/bindings/hwmon/lm70.txt new file mode 100644 index 000000000000..e7fd921aa4f1 --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/lm70.txt @@ -0,0 +1,21 @@ +* LM70/TMP121/LM71/LM74 thermometer. + +Required properties: +- compatible: one of + "ti,lm70" + "ti,tmp121" + "ti,lm71" + "ti,lm74" + +See Documentation/devicetree/bindings/spi/spi-bus.txt for more required and +optional properties. + +Example: + +spi_master { + temperature-sensor@0 { + compatible = "ti,lm70"; + reg = <0>; + spi-max-frequency = <1000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/hwmon/ltc2978.txt b/Documentation/devicetree/bindings/hwmon/ltc2978.txt index ed2f09dc2483..a7afbf60bb9c 100644 --- a/Documentation/devicetree/bindings/hwmon/ltc2978.txt +++ b/Documentation/devicetree/bindings/hwmon/ltc2978.txt @@ -3,10 +3,16 @@ ltc2978 Required properties: - compatible: should contain one of: * "lltc,ltc2974" + * "lltc,ltc2975" * "lltc,ltc2977" * "lltc,ltc2978" + * "lltc,ltc2980" * "lltc,ltc3880" + * "lltc,ltc3882" * "lltc,ltc3883" + * "lltc,ltc3886" + * "lltc,ltc3887" + * "lltc,ltm2987" * "lltc,ltm4676" - reg: I2C slave address @@ -17,10 +23,10 @@ Optional properties: standard binding for regulators; see regulator.txt. Valid names of regulators depend on number of supplies supported per device: - * ltc2974 : vout0 - vout3 - * ltc2977 : vout0 - vout7 + * ltc2974, ltc2975 : vout0 - vout3 + * ltc2977, ltc2980, ltm2987 : vout0 - vout7 * ltc2978 : vout0 - vout7 - * ltc3880 : vout0 - vout1 + * ltc3880, ltc3882, ltc3886 : vout0 - vout1 * ltc3883 : vout0 * ltm4676 : vout0 - vout1 diff --git a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt index b85184391b78..2a1f3af30155 100644 --- a/Documentation/devicetree/bindings/iio/adc/mcp320x.txt +++ b/Documentation/devicetree/bindings/iio/adc/mcp320x.txt @@ -18,6 +18,7 @@ Required properties: "mcp3202" "mcp3204" "mcp3208" + "mcp3301" Examples: diff --git a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt index 3eb40e20c143..1aad0514e647 100644 --- a/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/vf610-adc.txt @@ -17,6 +17,11 @@ Recommended properties: - Frequency in normal mode (ADLPC=0, ADHSC=0) - Frequency in high-speed mode (ADLPC=0, ADHSC=1) - Frequency in low-power mode (ADLPC=1, ADHSC=0) +- min-sample-time: Minimum sampling time in nanoseconds. This value has + to be chosen according to the conversion mode and the connected analog + source resistance (R_as) and capacitance (C_as). Refer the datasheet's + operating requirements. A safe default across a wide range of R_as and + C_as as well as conversion modes is 1000ns. Example: adc0: adc@4003b000 { diff --git a/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt b/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt new file mode 100644 index 000000000000..a01235c7fa15 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/magnetometer/mmc35240.txt @@ -0,0 +1,13 @@ +* MEMSIC MMC35240 magnetometer sensor + +Required properties: + + - compatible : should be "memsic,mmc35240" + - reg : the I2C address of the magnetometer + +Example: + +mmc35240@30 { + compatible = "memsic,mmc35240"; + reg = <0x30>; +}; diff --git a/Documentation/devicetree/bindings/iio/st-sensors.txt b/Documentation/devicetree/bindings/iio/st-sensors.txt index 8a6be3bdf267..d3ccdb190c53 100644 --- a/Documentation/devicetree/bindings/iio/st-sensors.txt +++ b/Documentation/devicetree/bindings/iio/st-sensors.txt @@ -35,6 +35,7 @@ Accelerometers: - st,lsm303dl-accel - st,lsm303dlm-accel - st,lsm330-accel +- st,lsm303agr-accel Gyroscopes: - st,l3g4200d-gyro @@ -46,6 +47,7 @@ Gyroscopes: - st,lsm330-gyro Magnetometers: +- st,lsm303agr-magn - st,lsm303dlh-magn - st,lsm303dlhc-magn - st,lsm303dlm-magn diff --git a/Documentation/devicetree/bindings/input/snvs-pwrkey.txt b/Documentation/devicetree/bindings/input/snvs-pwrkey.txt new file mode 100644 index 000000000000..70c14250323b --- /dev/null +++ b/Documentation/devicetree/bindings/input/snvs-pwrkey.txt @@ -0,0 +1 @@ +See Documentation/devicetree/bindings/crypto/fsl-sec4.txt diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt index 7da578d72123..2d6c8bb4d827 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt @@ -5,9 +5,14 @@ The BCM2835 contains a custom top-level interrupt controller, which supports controller, or the HW block containing it, is referred to occasionally as "armctrl" in the SoC documentation, hence naming of this binding. +The BCM2836 contains the same interrupt controller with the same +interrupts, but the per-CPU interrupt controller is the root, and an +interrupt there indicates that the ARMCTRL has an interrupt to handle. + Required properties: -- compatible : should be "brcm,bcm2835-armctrl-ic" +- compatible : should be "brcm,bcm2835-armctrl-ic" or + "brcm,bcm2836-armctrl-ic" - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller - #interrupt-cells : Specifies the number of cells needed to encode an @@ -20,6 +25,12 @@ Required properties: The 2nd cell contains the interrupt number within the bank. Valid values are 0..7 for bank 0, and 0..31 for bank 1. +Additional required properties for brcm,bcm2836-armctrl-ic: +- interrupt-parent : Specifies the parent interrupt controller when this + controller is the second level. +- interrupts : Specifies the interrupt on the parent for this interrupt + controller to handle. + The interrupt sources are as follows: Bank 0: @@ -102,9 +113,21 @@ Bank 2: Example: +/* BCM2835, first level */ intc: interrupt-controller { compatible = "brcm,bcm2835-armctrl-ic"; reg = <0x7e00b200 0x200>; interrupt-controller; #interrupt-cells = <2>; }; + +/* BCM2836, second level */ +intc: interrupt-controller { + compatible = "brcm,bcm2836-armctrl-ic"; + reg = <0x7e00b200 0x200>; + interrupt-controller; + #interrupt-cells = <2>; + + interrupt-parent = <&local_intc>; + interrupts = <8>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2836-l1-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2836-l1-intc.txt new file mode 100644 index 000000000000..f320dcd6e69b --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2836-l1-intc.txt @@ -0,0 +1,37 @@ +BCM2836 per-CPU interrupt controller + +The BCM2836 has a per-cpu interrupt controller for the timer, PMU +events, and SMP IPIs. One of the CPUs may receive interrupts for the +peripheral (GPU) events, which chain to the BCM2835-style interrupt +controller. + +Required properties: + +- compatible: Should be "brcm,bcm2836-l1-intc" +- reg: Specifies base physical address and size of the + registers +- interrupt-controller: Identifies the node as an interrupt controller +- #interrupt-cells: Specifies the number of cells needed to encode an + interrupt source. The value shall be 1 + +Please refer to interrupts.txt in this directory for details of the common +Interrupt Controllers bindings used by client devices. + +The interrupt sources are as follows: + +0: CNTPSIRQ +1: CNTPNSIRQ +2: CNTHPIRQ +3: CNTVIRQ +8: GPU_FAST +9: PMU_FAST + +Example: + +local_intc: local_intc { + compatible = "brcm,bcm2836-l1-intc"; + reg = <0x40000000 0x100>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&local_intc>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/msi.txt b/Documentation/devicetree/bindings/interrupt-controller/msi.txt new file mode 100644 index 000000000000..c60c034dcf19 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/msi.txt @@ -0,0 +1,135 @@ +This document describes the generic device tree binding for MSI controllers and +their master(s). + +Message Signaled Interrupts (MSIs) are a class of interrupts generated by a +write to an MMIO address. + +MSIs were originally specified by PCI (and are used with PCIe), but may also be +used with other busses, and hence a mechanism is required to relate devices on +those busses to the MSI controllers which they are capable of using, +potentially including additional information. + +MSIs are distinguished by some combination of: + +- The doorbell (the MMIO address written to). + + Devices may be configured by software to write to arbitrary doorbells which + they can address. An MSI controller may feature a number of doorbells. + +- The payload (the value written to the doorbell). + + Devices may be configured to write an arbitrary payload chosen by software. + MSI controllers may have restrictions on permitted payloads. + +- Sideband information accompanying the write. + + Typically this is neither configurable nor probeable, and depends on the path + taken through the memory system (i.e. it is a property of the combination of + MSI controller and device rather than a property of either in isolation). + + +MSI controllers: +================ + +An MSI controller signals interrupts to a CPU when a write is made to an MMIO +address by some master. An MSI controller may feature a number of doorbells. + +Required properties: +-------------------- + +- msi-controller: Identifies the node as an MSI controller. + +Optional properties: +-------------------- + +- #msi-cells: The number of cells in an msi-specifier, required if not zero. + + Typically this will encode information related to sideband data, and will + not encode doorbells or payloads as these can be configured dynamically. + + The meaning of the msi-specifier is defined by the device tree binding of + the specific MSI controller. + + +MSI clients +=========== + +MSI clients are devices which generate MSIs. For each MSI they wish to +generate, the doorbell and payload may be configured, though sideband +information may not be configurable. + +Required properties: +-------------------- + +- msi-parent: A list of phandle + msi-specifier pairs, one for each MSI + controller which the device is capable of using. + + This property is unordered, and MSIs may be allocated from any combination of + MSI controllers listed in the msi-parent property. + + If a device has restrictions on the allocation of MSIs, these restrictions + must be described with additional properties. + + When #msi-cells is non-zero, busses with an msi-parent will require + additional properties to describe the relationship between devices on the bus + and the set of MSIs they can potentially generate. + + +Example +======= + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi_a: msi-controller@a { + reg = <0xa 0xf00>; + compatible = "vendor-a,some-controller"; + msi-controller; + /* No sideband data, so #msi-cells omitted */ + }; + + msi_b: msi-controller@b { + reg = <0xb 0xf00>; + compatible = "vendor-b,another-controller"; + msi-controller; + /* Each device has some unique ID */ + #msi-cells = <1>; + }; + + msi_c: msi-controller@c { + reg = <0xb 0xf00>; + compatible = "vendor-b,another-controller"; + msi-controller; + /* Each device has some unique ID */ + #msi-cells = <1>; + }; + + dev@0 { + reg = <0x0 0xf00>; + compatible = "vendor-c,some-device"; + + /* Can only generate MSIs to msi_a */ + msi-parent = <&msi_a>; + }; + + dev@1 { + reg = <0x1 0xf00>; + compatible = "vendor-c,some-device"; + + /* + * Can generate MSIs to either A or B. + */ + msi-parent = <&msi_a>, <&msi_b 0x17>; + }; + + dev@2 { + reg = <0x2 0xf00>; + compatible = "vendor-c,some-device"; + /* + * Has different IDs at each MSI controller. + * Can generate MSIs to all of the MSI controllers. + */ + msi-parent = <&msi_a>, <&msi_b 0x17>, <&msi_c 0x53>; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/common.txt b/Documentation/devicetree/bindings/leds/common.txt index 747c53805eec..68419843e32f 100644 --- a/Documentation/devicetree/bindings/leds/common.txt +++ b/Documentation/devicetree/bindings/leds/common.txt @@ -29,14 +29,23 @@ Optional properties for child nodes: "ide-disk" - LED indicates disk activity "timer" - LED flashes at a fixed, configurable rate -- max-microamp : maximum intensity in microamperes of the LED - (torch LED for flash devices) -- flash-max-microamp : maximum intensity in microamperes of the - flash LED; it is mandatory if the LED should - support the flash mode -- flash-timeout-us : timeout in microseconds after which the flash - LED is turned off +- led-max-microamp : Maximum LED supply current in microamperes. This property + can be made mandatory for the board configurations + introducing a risk of hardware damage in case an excessive + current is set. + For flash LED controllers with configurable current this + property is mandatory for the LEDs in the non-flash modes + (e.g. torch or indicator). +Required properties for flash LED child nodes: +- flash-max-microamp : Maximum flash LED supply current in microamperes. +- flash-max-timeout-us : Maximum timeout in microseconds after which the flash + LED is turned off. + +For controllers that have no configurable current the flash-max-microamp +property can be omitted. +For controllers that have no configurable timeout the flash-max-timeout-us +property can be omitted. Examples: @@ -49,7 +58,7 @@ system-status { camera-flash { label = "Flash"; led-sources = <0>, <1>; - max-microamp = <50000>; + led-max-microamp = <50000>; flash-max-microamp = <320000>; - flash-timeout-us = <500000>; + flash-max-timeout-us = <500000>; }; diff --git a/Documentation/devicetree/bindings/leds/leds-ns2.txt b/Documentation/devicetree/bindings/leds/leds-ns2.txt index aef3aca34d2d..9f81258a5b6e 100644 --- a/Documentation/devicetree/bindings/leds/leds-ns2.txt +++ b/Documentation/devicetree/bindings/leds/leds-ns2.txt @@ -8,6 +8,9 @@ Each LED is represented as a sub-node of the ns2-leds device. Required sub-node properties: - cmd-gpio: Command LED GPIO. See OF device-tree GPIO specification. - slow-gpio: Slow LED GPIO. See OF device-tree GPIO specification. +- modes-map: A mapping between LED modes (off, on or SATA activity blinking) and + the corresponding cmd-gpio/slow-gpio values. All the GPIO values combinations + should be given in order to avoid having an unknown mode at driver probe time. Optional sub-node properties: - label: Name for this LED. If omitted, the label is taken from the node name. @@ -15,6 +18,8 @@ Optional sub-node properties: Example: +#include <dt-bindings/leds/leds-ns2.h> + ns2-leds { compatible = "lacie,ns2-leds"; @@ -22,5 +27,9 @@ ns2-leds { label = "ns2:blue:sata"; slow-gpio = <&gpio0 29 0>; cmd-gpio = <&gpio0 30 0>; + modes-map = <NS_V2_LED_OFF 0 1 + NS_V2_LED_ON 1 0 + NS_V2_LED_ON 0 0 + NS_V2_LED_SATA 1 1>; }; }; diff --git a/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt new file mode 100644 index 000000000000..e6df32f9986d --- /dev/null +++ b/Documentation/devicetree/bindings/memory-controllers/arm,pl172.txt @@ -0,0 +1,125 @@ +* Device tree bindings for ARM PL172 MultiPort Memory Controller + +Required properties: + +- compatible: "arm,pl172", "arm,primecell" + +- reg: Must contains offset/length value for controller. + +- #address-cells: Must be 2. The partition number has to be encoded in the + first address cell and it may accept values 0..N-1 + (N - total number of partitions). The second cell is the + offset into the partition. + +- #size-cells: Must be set to 1. + +- ranges: Must contain one or more chip select memory regions. + +- clocks: Must contain references to controller clocks. + +- clock-names: Must contain "mpmcclk" and "apb_pclk". + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + See clock-bindings.txt + +Child chip-select (cs) nodes contain the memory devices nodes connected to +such as NOR (e.g. cfi-flash) and NAND. + +Required child cs node properties: + +- #address-cells: Must be 2. + +- #size-cells: Must be 1. + +- ranges: Empty property indicating that child nodes can inherit + memory layout. + +- clock-ranges: Empty property indicating that child nodes can inherit + named clocks. Required only if clock tree data present + in device tree. + +- mpmc,cs: Chip select number. Indicates to the pl0172 driver + which chipselect is used for accessing the memory. + +- mpmc,memory-width: Width of the chip select memory. Must be equal to + either 8, 16 or 32. + +Optional child cs node config properties: + +- mpmc,async-page-mode: Enable asynchronous page mode. + +- mpmc,cs-active-high: Set chip select polarity to active high. + +- mpmc,byte-lane-low: Set byte lane state to low. + +- mpmc,extended-wait: Enable extended wait. + +- mpmc,buffer-enable: Enable write buffer. + +- mpmc,write-protect: Enable write protect. + +Optional child cs node timing properties: + +- mpmc,write-enable-delay: Delay from chip select assertion to write + enable (WE signal) in nano seconds. + +- mpmc,output-enable-delay: Delay from chip select assertion to output + enable (OE signal) in nano seconds. + +- mpmc,write-access-delay: Delay from chip select assertion to write + access in nano seconds. + +- mpmc,read-access-delay: Delay from chip select assertion to read + access in nano seconds. + +- mpmc,page-mode-read-delay: Delay for asynchronous page mode sequential + accesses in nano seconds. + +- mpmc,turn-round-delay: Delay between access to memory banks in nano + seconds. + +If any of the above timing parameters are absent, current parameter value will +be taken from the corresponding HW reg. + +Example for pl172 with nor flash on chip select 0 shown below. + +emc: memory-controller@40005000 { + compatible = "arm,pl172", "arm,primecell"; + reg = <0x40005000 0x1000>; + clocks = <&ccu1 CLK_CPU_EMCDIV>, <&ccu1 CLK_CPU_EMC>; + clock-names = "mpmcclk", "apb_pclk"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x1c000000 0x1000000 + 1 0 0x1d000000 0x1000000 + 2 0 0x1e000000 0x1000000 + 3 0 0x1f000000 0x1000000>; + + cs0 { + #address-cells = <2>; + #size-cells = <1>; + ranges; + + mpmc,cs = <0>; + mpmc,memory-width = <16>; + mpmc,byte-lane-low; + mpmc,write-enable-delay = <0>; + mpmc,output-enable-delay = <0>; + mpmc,read-enable-delay = <70>; + mpmc,page-mode-read-delay = <70>; + + flash@0,0 { + compatible = "sst,sst39vf320", "cfi-flash"; + reg = <0 0 0x400000>; + bank-width = <2>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "data"; + reg = <0 0x400000>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/memory-controllers/synopsys.txt b/Documentation/devicetree/bindings/memory-controllers/synopsys.txt index f9c6454146b6..a43d26d41e04 100644 --- a/Documentation/devicetree/bindings/memory-controllers/synopsys.txt +++ b/Documentation/devicetree/bindings/memory-controllers/synopsys.txt @@ -1,5 +1,9 @@ Binding for Synopsys IntelliDDR Multi Protocol Memory Controller +This controller has an optional ECC support in half-bus width (16-bit) +configuration. The ECC controller corrects one bit error and detects +two bit errors. + Required properties: - compatible: Should be 'xlnx,zynq-ddrc-a05' - reg: Base address and size of the controllers memory area diff --git a/Documentation/devicetree/bindings/mfd/rk808.txt b/Documentation/devicetree/bindings/mfd/rk808.txt index 9e6e2592e5c8..4ca6aab4273a 100644 --- a/Documentation/devicetree/bindings/mfd/rk808.txt +++ b/Documentation/devicetree/bindings/mfd/rk808.txt @@ -24,6 +24,10 @@ Optional properties: - vcc10-supply: The input supply for LDO_REG6 - vcc11-supply: The input supply for LDO_REG8 - vcc12-supply: The input supply for SWITCH_REG2 +- dvs-gpios: buck1/2 can be controlled by gpio dvs, this is GPIO specifiers + for 2 host gpio's used for dvs. The format of the gpio specifier depends in + the gpio controller. If DVS GPIOs aren't present, voltage changes will happen + very quickly with no slow ramp time. Regulators: All the regulators of RK808 to be instantiated shall be listed in a child node named 'regulators'. Each regulator is represented @@ -55,7 +59,9 @@ Example: interrupt-parent = <&gpio0>; interrupts = <4 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&pmic_int>; + pinctrl-0 = <&pmic_int &dvs_1 &dvs_2>; + dvs-gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>, + <&gpio7 15 GPIO_ACTIVE_HIGH>; reg = <0x1b>; rockchip,system-power-controller; wakeup-source; diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 4461dc71cb10..862aa2f8837a 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -1,7 +1,8 @@ * Freescale Quad Serial Peripheral Interface(QuadSPI) Required properties: - - compatible : Should be "fsl,vf610-qspi" or "fsl,imx6sx-qspi" + - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi", + "fsl,imx7d-qspi", "fsl,imx6ul-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" diff --git a/Documentation/devicetree/bindings/mtd/nxp-spifi.txt b/Documentation/devicetree/bindings/mtd/nxp-spifi.txt new file mode 100644 index 000000000000..f8b6b250654e --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/nxp-spifi.txt @@ -0,0 +1,58 @@ +* NXP SPI Flash Interface (SPIFI) + +NXP SPIFI is a specialized SPI interface for serial Flash devices. +It supports one Flash device with 1-, 2- and 4-bits width in SPI +mode 0 or 3. The controller operates in either command or memory +mode. In memory mode the Flash is accessible from the CPU as +normal memory. + +Required properties: + - compatible : Should be "nxp,lpc1773-spifi" + - reg : the first contains the register location and length, + the second contains the memory mapping address and length + - reg-names: Should contain the reg names "spifi" and "flash" + - interrupts : Should contain the interrupt for the device + - clocks : The clocks needed by the SPIFI controller + - clock-names : Should contain the clock names "spifi" and "reg" + +Optional properties: + - resets : phandle + reset specifier + +The SPI Flash must be a child of the SPIFI node and must have a +compatible property as specified in bindings/mtd/jedec,spi-nor.txt + +Optionally it can also contain the following properties. + - spi-cpol : Controller only supports mode 0 and 3 so either + both spi-cpol and spi-cpha should be present or + none of them + - spi-cpha : See above + - spi-rx-bus-width : Used to select how many pins that are used + for input on the controller + +See bindings/spi/spi-bus.txt for more information. + +Example: +spifi: spifi@40003000 { + compatible = "nxp,lpc1773-spifi"; + reg = <0x40003000 0x1000>, <0x14000000 0x4000000>; + reg-names = "spifi", "flash"; + interrupts = <30>; + clocks = <&ccu1 CLK_SPIFI>, <&ccu1 CLK_CPU_SPIFI>; + clock-names = "spifi", "reg"; + resets = <&rgu 53>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-cpol; + spi-cpha; + spi-rx-bus-width = <4>; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "data"; + reg = <0 0x200000>; + }; + }; +}; + diff --git a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt index 4f833e3c4f51..d9b655f11048 100644 --- a/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt +++ b/Documentation/devicetree/bindings/mtd/pxa3xx-nand.txt @@ -11,6 +11,7 @@ Required properties: Optional properties: + - dmas: dma data channel, see dma.txt binding doc - marvell,nand-enable-arbiter: Set to enable the bus arbiter - marvell,nand-keep-config: Set to keep the NAND controller config as set by the bootloader @@ -32,6 +33,8 @@ Example: compatible = "marvell,pxa3xx-nand"; reg = <0x43100000 90>; interrupts = <45>; + dmas = <&pdma 97 0>; + dma-names = "data"; #address-cells = <1>; marvell,nand-enable-arbiter; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt index 33fe8462edf4..a9df21aaa154 100644 --- a/Documentation/devicetree/bindings/net/cpsw.txt +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -2,7 +2,11 @@ TI SoC Ethernet Switch Controller Device Tree Bindings ------------------------------------------------------ Required properties: -- compatible : Should be "ti,cpsw" +- compatible : Should be one of the below:- + "ti,cpsw" for backward compatible + "ti,am335x-cpsw" for AM335x controllers + "ti,am4372-cpsw" for AM437x controllers + "ti,dra7-cpsw" for DRA7x controllers - reg : physical base address and size of the cpsw registers map - interrupts : property with a value describing the interrupt diff --git a/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt index fabdf64a5737..d543ed3f5363 100644 --- a/Documentation/devicetree/bindings/misc/allwinner,sunxi-sid.txt +++ b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt @@ -4,6 +4,10 @@ Required properties: - compatible: "allwinner,sun4i-a10-sid" or "allwinner,sun7i-a20-sid" - reg: Should contain registers location and length += Data cells = +Are child nodes of qfprom, bindings of which as described in +bindings/nvmem/nvmem.txt + Example for sun4i: sid@01c23800 { compatible = "allwinner,sun4i-a10-sid"; diff --git a/Documentation/devicetree/bindings/nvmem/nvmem.txt b/Documentation/devicetree/bindings/nvmem/nvmem.txt new file mode 100644 index 000000000000..b52bc11e9597 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/nvmem.txt @@ -0,0 +1,80 @@ += NVMEM(Non Volatile Memory) Data Device Tree Bindings = + +This binding is intended to represent the location of hardware +configuration data stored in NVMEMs like eeprom, efuses and so on. + +On a significant proportion of boards, the manufacturer has stored +some data on NVMEM, for the OS to be able to retrieve these information +and act upon it. Obviously, the OS has to know about where to retrieve +these data from, and where they are stored on the storage device. + +This document is here to document this. + += Data providers = +Contains bindings specific to provider drivers and data cells as children +of this node. + +Optional properties: + read-only: Mark the provider as read only. + += Data cells = +These are the child nodes of the provider which contain data cell +information like offset and size in nvmem provider. + +Required properties: +reg: specifies the offset in byte within the storage device. + +Optional properties: + +bits: Is pair of bit location and number of bits, which specifies offset + in bit and number of bits within the address range specified by reg property. + Offset takes values from 0-7. + +For example: + + /* Provider */ + qfprom: qfprom@00700000 { + ... + + /* Data cells */ + tsens_calibration: calib@404 { + reg = <0x404 0x10>; + }; + + tsens_calibration_bckp: calib_bckp@504 { + reg = <0x504 0x11>; + bits = <6 128> + }; + + pvs_version: pvs-version@6 { + reg = <0x6 0x2> + bits = <7 2> + }; + + speed_bin: speed-bin@c{ + reg = <0xc 0x1>; + bits = <2 3>; + + }; + ... + }; + += Data consumers = +Are device nodes which consume nvmem data cells/providers. + +Required-properties: +nvmem-cells: list of phandle to the nvmem data cells. +nvmem-cell-names: names for the each nvmem-cells specified. Required if + nvmem-cells is used. + +Optional-properties: +nvmem : list of phandles to nvmem providers. +nvmem-names: names for the each nvmem provider. required if nvmem is used. + +For example: + + tsens { + ... + nvmem-cells = <&tsens_calibration>; + nvmem-cell-names = "calibration"; + }; diff --git a/Documentation/devicetree/bindings/nvmem/qfprom.txt b/Documentation/devicetree/bindings/nvmem/qfprom.txt new file mode 100644 index 000000000000..4ad68b7f5c18 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/qfprom.txt @@ -0,0 +1,35 @@ += Qualcomm QFPROM device tree bindings = + +This binding is intended to represent QFPROM which is found in most QCOM SOCs. + +Required properties: +- compatible: should be "qcom,qfprom" +- reg: Should contain registers location and length + += Data cells = +Are child nodes of qfprom, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example: + + qfprom: qfprom@00700000 { + compatible = "qcom,qfprom"; + reg = <0x00700000 0x8000>; + ... + /* Data cells */ + tsens_calibration: calib@404 { + reg = <0x4404 0x10>; + }; + }; + + += Data consumers = +Are device nodes which consume nvmem data cells. + +For example: + + tsens { + ... + nvmem-cells = <&tsens_calibration>; + nvmem-cell-names = "calibration"; + }; diff --git a/Documentation/devicetree/bindings/power/opp.txt b/Documentation/devicetree/bindings/opp/opp.txt index 0d5e7c978121..0cb44dc21f97 100644 --- a/Documentation/devicetree/bindings/power/opp.txt +++ b/Documentation/devicetree/bindings/opp/opp.txt @@ -88,7 +88,7 @@ This defines voltage-current-frequency combinations along with other related properties. Required properties: -- opp-hz: Frequency in Hz +- opp-hz: Frequency in Hz, expressed as a 64-bit big-endian integer. Optional properties: - opp-microvolt: voltage in micro Volts. @@ -158,20 +158,20 @@ Example 1: Single cluster Dual-core ARM cortex A9, switch DVFS states together. opp-shared; opp00 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; opp01 { - opp-hz = <1100000000>; + opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <980000 1000000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; opp02 { - opp-hz = <1200000000>; + opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; clock-latency-ns = <290000>; turbo-mode; @@ -237,20 +237,20 @@ independently. */ opp00 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; opp01 { - opp-hz = <1100000000>; + opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <980000 1000000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; opp02 { - opp-hz = <1200000000>; + opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; opp-microamp = <90000; lock-latency-ns = <290000>; @@ -313,20 +313,20 @@ DVFS state together. opp-shared; opp00 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>; opp-microamp = <70000>; clock-latency-ns = <300000>; opp-suspend; }; opp01 { - opp-hz = <1100000000>; + opp-hz = /bits/ 64 <1100000000>; opp-microvolt = <980000 1000000 1010000>; opp-microamp = <80000>; clock-latency-ns = <310000>; }; opp02 { - opp-hz = <1200000000>; + opp-hz = /bits/ 64 <1200000000>; opp-microvolt = <1025000>; opp-microamp = <90000>; clock-latency-ns = <290000>; @@ -339,20 +339,20 @@ DVFS state together. opp-shared; opp10 { - opp-hz = <1300000000>; + opp-hz = /bits/ 64 <1300000000>; opp-microvolt = <1045000 1050000 1055000>; opp-microamp = <95000>; clock-latency-ns = <400000>; opp-suspend; }; opp11 { - opp-hz = <1400000000>; + opp-hz = /bits/ 64 <1400000000>; opp-microvolt = <1075000>; opp-microamp = <100000>; clock-latency-ns = <400000>; }; opp12 { - opp-hz = <1500000000>; + opp-hz = /bits/ 64 <1500000000>; opp-microvolt = <1010000 1100000 1110000>; opp-microamp = <95000>; clock-latency-ns = <400000>; @@ -379,7 +379,7 @@ Example 4: Handling multiple regulators opp-shared; opp00 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000>, /* Supply 0 */ <960000>, /* Supply 1 */ <960000>; /* Supply 2 */ @@ -392,7 +392,7 @@ Example 4: Handling multiple regulators /* OR */ opp00 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>, /* Supply 0 */ <960000 965000 975000>, /* Supply 1 */ <960000 965000 975000>; /* Supply 2 */ @@ -405,7 +405,7 @@ Example 4: Handling multiple regulators /* OR */ opp00 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; opp-microvolt = <970000 975000 985000>, /* Supply 0 */ <960000 965000 975000>, /* Supply 1 */ <960000 965000 975000>; /* Supply 2 */ @@ -437,12 +437,12 @@ Example 5: Multiple OPP tables opp-shared; opp00 { - opp-hz = <600000000>; + opp-hz = /bits/ 64 <600000000>; ... }; opp01 { - opp-hz = <800000000>; + opp-hz = /bits/ 64 <800000000>; ... }; }; @@ -453,12 +453,12 @@ Example 5: Multiple OPP tables opp-shared; opp10 { - opp-hz = <1000000000>; + opp-hz = /bits/ 64 <1000000000>; ... }; opp11 { - opp-hz = <1100000000>; + opp-hz = /bits/ 64 <1100000000>; ... }; }; diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt index 3d217911b313..60e25161f351 100644 --- a/Documentation/devicetree/bindings/pci/ti-pci.txt +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -23,6 +23,9 @@ PCIe Designware Controller interrupt-map-mask, interrupt-map : as specified in ../designware-pcie.txt +Optional Property: + - gpios : Should be added if a gpio line is required to drive PERST# line + Example: axi { compatible = "simple-bus"; diff --git a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt new file mode 100644 index 000000000000..bd61b467e30a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt @@ -0,0 +1,26 @@ +NXP LPC18xx/43xx internal USB OTG PHY binding +--------------------------------------------- + +This file contains documentation for the internal USB OTG PHY found +in NXP LPC18xx and LPC43xx SoCs. + +Required properties: +- compatible : must be "nxp,lpc1850-usb-otg-phy" +- clocks : must be exactly one entry +See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- #phy-cells : must be 0 for this phy +See: Documentation/devicetree/bindings/phy/phy-bindings.txt + +The phy node must be a child of the creg syscon node. + +Example: +creg: syscon@40043000 { + compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; + reg = <0x40043000 0x1000>; + + usb0_otg_phy: phy@004 { + compatible = "nxp,lpc1850-usb-otg-phy"; + clocks = <&ccu1 CLK_USB0>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt index 16528b9eb561..0cebf7454517 100644 --- a/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt +++ b/Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt @@ -7,6 +7,8 @@ Required properties: * allwinner,sun5i-a13-usb-phy * allwinner,sun6i-a31-usb-phy * allwinner,sun7i-a20-usb-phy + * allwinner,sun8i-a23-usb-phy + * allwinner,sun8i-a33-usb-phy - reg : a list of offset + length pairs - reg-names : * "phy_ctrl" @@ -17,12 +19,21 @@ Required properties: - clock-names : * "usb_phy" for sun4i, sun5i or sun7i * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i + * "usb0_phy", "usb1_phy" for sun8i - resets : a list of phandle + reset specifier pairs - reset-names : * "usb0_reset" * "usb1_reset" * "usb2_reset" for sun4i, sun6i or sun7i +Optional properties: +- usb0_id_det-gpios : gpio phandle for reading the otg id pin value +- usb0_vbus_det-gpios : gpio phandle for detecting the presence of usb0 vbus +- usb0_vbus_power-supply: power-supply phandle for usb0 vbus presence detect +- usb0_vbus-supply : regulator phandle for controller usb0 vbus +- usb1_vbus-supply : regulator phandle for controller usb1 vbus +- usb2_vbus-supply : regulator phandle for controller usb2 vbus + Example: usbphy: phy@0x01c13400 { #phy-cells = <1>; @@ -32,6 +43,13 @@ Example: reg-names = "phy_ctrl", "pmu1", "pmu2"; clocks = <&usb_clk 8>; clock-names = "usb_phy"; - resets = <&usb_clk 1>, <&usb_clk 2>; - reset-names = "usb1_reset", "usb2_reset"; + resets = <&usb_clk 0>, <&usb_clk 1>, <&usb_clk 2>; + reset-names = "usb0_reset", "usb1_reset", "usb2_reset"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; /* PH19 */ + usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; /* PH22 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; }; diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt new file mode 100644 index 000000000000..a81bbf37ed66 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6 UltraLite IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx6ul-iomuxc" +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + imx6ul-pinfunc.h under device tree source folder. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX6 UltraLite + Reference Manual for detailed CONFIG settings. + +CONFIG bits definition: +PAD_CTL_HYS (1 << 16) +PAD_CTL_PUS_100K_DOWN (0 << 14) +PAD_CTL_PUS_47K_UP (1 << 14) +PAD_CTL_PUS_100K_UP (2 << 14) +PAD_CTL_PUS_22K_UP (3 << 14) +PAD_CTL_PUE (1 << 13) +PAD_CTL_PKE (1 << 12) +PAD_CTL_ODE (1 << 11) +PAD_CTL_SPEED_LOW (0 << 6) +PAD_CTL_SPEED_MED (1 << 6) +PAD_CTL_SPEED_HIGH (3 << 6) +PAD_CTL_DSE_DISABLE (0 << 3) +PAD_CTL_DSE_260ohm (1 << 3) +PAD_CTL_DSE_130ohm (2 << 3) +PAD_CTL_DSE_87ohm (3 << 3) +PAD_CTL_DSE_65ohm (4 << 3) +PAD_CTL_DSE_52ohm (5 << 3) +PAD_CTL_DSE_43ohm (6 << 3) +PAD_CTL_DSE_37ohm (7 << 3) +PAD_CTL_SRE_FAST (1 << 0) +PAD_CTL_SRE_SLOW (0 << 0) diff --git a/Documentation/devicetree/bindings/power/power_domain.txt b/Documentation/devicetree/bindings/power/power_domain.txt index 0f8ed3710c66..025b5e7df61c 100644 --- a/Documentation/devicetree/bindings/power/power_domain.txt +++ b/Documentation/devicetree/bindings/power/power_domain.txt @@ -48,7 +48,7 @@ Example 2: #power-domain-cells = <1>; }; - child: power-controller@12340000 { + child: power-controller@12341000 { compatible = "foo,power-controller"; reg = <0x12341000 0x1000>; power-domains = <&parent 0>; diff --git a/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt new file mode 100644 index 000000000000..0e6d8754e7ec --- /dev/null +++ b/Documentation/devicetree/bindings/power/qcom,coincell-charger.txt @@ -0,0 +1,48 @@ +Qualcomm Coincell Charger: + +The hardware block controls charging for a coincell or capacitor that is +used to provide power backup for certain features of the power management +IC (PMIC) + +- compatible: + Usage: required + Value type: <string> + Definition: must be: "qcom,pm8941-coincell" + +- reg: + Usage: required + Value type: <u32> + Definition: base address of the coincell charger registers + +- qcom,rset-ohms: + Usage: required + Value type: <u32> + Definition: resistance (in ohms) for current-limiting resistor + must be one of: 800, 1200, 1700, 2100 + +- qcom,vset-millivolts: + Usage: required + Value type: <u32> + Definition: voltage (in millivolts) to apply for charging + must be one of: 2500, 3000, 3100, 3200 + +- qcom,charger-disable: + Usage: optional + Value type: <boolean> + Definition: definining this property disables charging + +This charger is a sub-node of one of the 8941 PMIC blocks, and is specified +as a child node in DTS of that node. See ../mfd/qcom,spmi-pmic.txt and +../mfd/qcom-pm8xxx.txt + +Example: + + pm8941@0 { + coincell@2800 { + compatible = "qcom,pm8941-coincell"; + reg = <0x2800>; + + qcom,rset-ohms = <2100>; + qcom,vset-millivolts = <3000>; + }; + }; diff --git a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt index 8b70db103ca7..b8627e763dba 100644 --- a/Documentation/devicetree/bindings/power/rockchip-io-domain.txt +++ b/Documentation/devicetree/bindings/power/rockchip-io-domain.txt @@ -33,6 +33,8 @@ Required properties: - compatible: should be one of: - "rockchip,rk3188-io-voltage-domain" for rk3188 - "rockchip,rk3288-io-voltage-domain" for rk3288 + - "rockchip,rk3368-io-voltage-domain" for rk3368 + - "rockchip,rk3368-pmu-io-voltage-domain" for rk3368 pmu-domains - rockchip,grf: phandle to the syscon managing the "general register files" @@ -64,6 +66,18 @@ Possible supplies for rk3288: - sdcard-supply: The supply connected to SDMMC0_VDD. - wifi-supply: The supply connected to APIO3_VDD. Also known as SDIO0. +Possible supplies for rk3368: +- audio-supply: The supply connected to APIO3_VDD. +- dvp-supply: The supply connected to DVPIO_VDD. +- flash0-supply: The supply connected to FLASH0_VDD. Typically for eMMC +- gpio30-supply: The supply connected to APIO1_VDD. +- gpio1830 The supply connected to APIO4_VDD. +- sdcard-supply: The supply connected to SDMMC0_VDD. +- wifi-supply: The supply connected to APIO2_VDD. Also known as SDIO0. + +Possible supplies for rk3368 pmu-domains: +- pmu-supply: The supply connected to PMUIO_VDD. +- vop-supply: The supply connected to LCDC_VDD. Example: diff --git a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt index 8832e8798912..647817527c88 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/mpc5121-psc.txt @@ -6,14 +6,14 @@ PSC in UART mode For PSC in UART mode the needed PSC serial devices are specified by fsl,mpc5121-psc-uart nodes in the fsl,mpc5121-immr SoC node. Additionally the PSC FIFO -Controller node fsl,mpc5121-psc-fifo is requered there: +Controller node fsl,mpc5121-psc-fifo is required there: -fsl,mpc5121-psc-uart nodes +fsl,mpc512x-psc-uart nodes -------------------------- Required properties : - - compatible : Should contain "fsl,mpc5121-psc-uart" and "fsl,mpc5121-psc" - - cell-index : Index of the PSC in hardware + - compatible : Should contain "fsl,<soc>-psc-uart" and "fsl,<soc>-psc" + Supported <soc>s: mpc5121, mpc5125 - reg : Offset and length of the register set for the PSC device - interrupts : <a b> where a is the interrupt number of the PSC FIFO Controller and b is a field that represents an @@ -25,12 +25,21 @@ Recommended properties : - fsl,rx-fifo-size : the size of the RX fifo slice (a multiple of 4) - fsl,tx-fifo-size : the size of the TX fifo slice (a multiple of 4) +PSC in SPI mode +--------------- -fsl,mpc5121-psc-fifo node +Similar to the UART mode a PSC can be operated in SPI mode. The compatible used +for that is fsl,mpc5121-psc-spi. It requires a fsl,mpc5121-psc-fifo as well. +The required and recommended properties are identical to the +fsl,mpc5121-psc-uart nodes, just use spi instead of uart in the compatible +string. + +fsl,mpc512x-psc-fifo node ------------------------- Required properties : - - compatible : Should be "fsl,mpc5121-psc-fifo" + - compatible : Should be "fsl,<soc>-psc-fifo" + Supported <soc>s: mpc5121, mpc5125 - reg : Offset and length of the register set for the PSC FIFO Controller - interrupts : <a b> where a is the interrupt number of the @@ -39,6 +48,9 @@ Required properties : - interrupt-parent : the phandle for the interrupt controller that services interrupts for this device. +Recommended properties : + - clocks : specifies the clock needed to operate the fifo controller + - clock-names : name(s) for the clock(s) listed in clocks Example for a board using PSC0 and PSC1 devices in serial mode: diff --git a/Documentation/devicetree/bindings/regulator/da9210.txt b/Documentation/devicetree/bindings/regulator/da9210.txt index 3297c53cb915..7aa9b1fa6b21 100644 --- a/Documentation/devicetree/bindings/regulator/da9210.txt +++ b/Documentation/devicetree/bindings/regulator/da9210.txt @@ -5,6 +5,10 @@ Required properties: - compatible: must be "dlg,da9210" - reg: the i2c slave address of the regulator. It should be 0x68. +Optional properties: + +- interrupts: a reference to the DA9210 interrupt, if available. + Any standard regulator properties can be used to configure the single da9210 DCDC. diff --git a/Documentation/devicetree/bindings/regulator/da9211.txt b/Documentation/devicetree/bindings/regulator/da9211.txt index eb618907c7de..c620493e8dbe 100644 --- a/Documentation/devicetree/bindings/regulator/da9211.txt +++ b/Documentation/devicetree/bindings/regulator/da9211.txt @@ -1,7 +1,7 @@ -* Dialog Semiconductor DA9211/DA9213 Voltage Regulator +* Dialog Semiconductor DA9211/DA9213/DA9215 Voltage Regulator Required properties: -- compatible: "dlg,da9211" or "dlg,da9213". +- compatible: "dlg,da9211" or "dlg,da9213" or "dlg,da9215" - reg: I2C slave address, usually 0x68. - interrupts: the interrupt outputs of the controller - regulators: A node that houses a sub-node for each regulator within the @@ -66,3 +66,31 @@ Example 2) DA9213 }; }; }; + + +Example 3) DA9215 + pmic: da9215@68 { + compatible = "dlg,da9215"; + reg = <0x68>; + interrupts = <3 27>; + + regulators { + BUCKA { + regulator-name = "VBUCKA"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <4000000>; + regulator-max-microamp = <7000000>; + enable-gpios = <&gpio 27 0>; + }; + BUCKB { + regulator-name = "VBUCKB"; + regulator-min-microvolt = < 300000>; + regulator-max-microvolt = <1570000>; + regulator-min-microamp = <4000000>; + regulator-max-microamp = <7000000>; + enable-gpios = <&gpio 17 0>; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt index 55efb24e5683..f80ea2fe27e6 100644 --- a/Documentation/devicetree/bindings/regulator/max8973-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/max8973-regulator.txt @@ -25,6 +25,12 @@ Optional properties: -maxim,enable-frequency-shift: boolean, enable 9% frequency shift. -maxim,enable-bias-control: boolean, enable bias control. By enabling this startup delay can be reduce to 20us from 220us. +-maxim,enable-etr: boolean, enable Enhanced Transient Response. +-maxim,enable-high-etr-sensitivity: boolean, Enhanced transient response + circuit is enabled and set for high sensitivity. If this + property is available then etr will be enable default. + +Enhanced transient response (ETR) will affect the configuration of CKADV. Example: diff --git a/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt new file mode 100644 index 000000000000..02649d8b3f5a --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/mt6311-regulator.txt @@ -0,0 +1,35 @@ +Mediatek MT6311 Regulator Driver + +Required properties: +- compatible: "mediatek,mt6311-regulator" +- reg: I2C slave address, usually 0x6b. +- regulators: List of regulators provided by this controller. It is named + to VDVFS and VBIASN. + The definition for each of these nodes is defined using the standard binding + for regulators at Documentation/devicetree/bindings/regulator/regulator.txt. + +The valid names for regulators are: +BUCK: + VDVFS +LDO: + VBIASN + +Example: + mt6311: pmic@6b { + compatible = "mediatek,mt6311-regulator"; + reg = <0x6b>; + + regulators { + mt6311_vcpu_reg: VDVFS { + regulator-name = "VDVFS"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1400000>; + regulator-ramp-delay = <10000>; + }; + mt6311_ldo_reg: VBIASN { + regulator-name = "VBIASN"; + regulator-min-microvolt = <200000>; + regulator-max-microvolt = <800000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt index ce91f61feb12..ed936f0f34f2 100644 --- a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt @@ -1,27 +1,68 @@ -pwm regulator bindings +Bindings for the Generic PWM Regulator +====================================== + +Currently supports 2 modes of operation: + +Voltage Table: When in this mode, a voltage table (See below) of + predefined voltage <=> duty-cycle values must be + provided via DT. Limitations are that the regulator can + only operate at the voltages supplied in the table. + Intermediary duty-cycle values which would normally + allow finer grained voltage selection are ignored and + rendered useless. Although more control is given to + the user if the assumptions made in continuous-voltage + mode do not reign true. + +Continuous Voltage: This mode uses the regulator's maximum and minimum + supplied voltages specified in the + regulator-{min,max}-microvolt properties to calculate + appropriate duty-cycle values. This allows for a much + more fine grained solution when compared with + voltage-table mode above. This solution does make an + assumption that a %50 duty-cycle value will cause the + regulator voltage to run at half way between the + supplied max_uV and min_uV values. Required properties: -- compatible: Should be "pwm-regulator" -- pwms: OF device-tree PWM specification (see PWM binding pwm.txt) -- voltage-table: voltage and duty table, include 2 members in each set of - brackets, first one is voltage(unit: uv), the next is duty(unit: percent) +-------------------- +- compatible: Should be "pwm-regulator" + +- pwms: PWM specification (See: ../pwm/pwm.txt) + +Only required for Voltage Table Mode: +- voltage-table: Voltage and Duty-Cycle table consisting of 2 cells + First cell is voltage in microvolts (uV) + Second cell is duty-cycle in percent (%) + +NB: To be clear, if voltage-table is provided, then the device will be used +in Voltage Table Mode. If no voltage-table is provided, then the device will +be used in Continuous Voltage Mode. -Any property defined as part of the core regulator binding defined in -regulator.txt can also be used. +Any property defined as part of the core regulator binding can also be used. +(See: ../regulator/regulator.txt) -Example: +Continuous Voltage Example: pwm_regulator { compatible = "pwm-regulator; pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + }; +Voltage Table Example: + pwm_regulator { + compatible = "pwm-regulator; + pwms = <&pwm1 0 8448 0>; + regulator-min-microvolt = <1016000>; + regulator-max-microvolt = <1114000>; + regulator-name = "vdd_logic"; + + /* Voltage Duty-Cycle */ voltage-table = <1114000 0>, <1095000 10>, <1076000 20>, <1056000 30>, <1036000 40>, <1016000 50>; - - regulator-min-microvolt = <1016000>; - regulator-max-microvolt = <1114000>; - regulator-name = "vdd_logic"; }; diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt index 75b4604bad07..d00bfd8624a5 100644 --- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt +++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt @@ -91,13 +91,65 @@ see regulator.txt - with additional custom properties described below: - regulator-initial-mode: Usage: optional Value type: <u32> - Descrption: 1 = Set initial mode to high power mode (HPM), also referred - to as NPM. HPM consumes more ground current than LPM, but + Description: 2 = Set initial mode to auto mode (automatically select + between HPM and LPM); not available on boost type + regulators. + + 1 = Set initial mode to high power mode (HPM), also referred + to as NPM. HPM consumes more ground current than LPM, but it can source significantly higher load current. HPM is not available on boost type regulators. For voltage switch type regulators, HPM implies that over current protection and - soft start are active all the time. 0 = Set initial mode to - low power mode (LPM). + soft start are active all the time. + + 0 = Set initial mode to low power mode (LPM). + +- qcom,ocp-max-retries: + Usage: optional + Value type: <u32> + Description: Maximum number of times to try toggling a voltage switch + off and back on as a result of consecutive over current + events. + +- qcom,ocp-retry-delay: + Usage: optional + Value type: <u32> + Description: Time to delay in milliseconds between each voltage switch + toggle after an over current event takes place. + +- qcom,pin-ctrl-enable: + Usage: optional + Value type: <u32> + Description: Bit mask specifying which hardware pins should be used to + enable the regulator, if any; supported bits are: + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + +- qcom,pin-ctrl-hpm: + Usage: optional + Value type: <u32> + Description: Bit mask specifying which hardware pins should be used to + force the regulator into high power mode, if any; + supported bits are: + 0 = ignore all hardware enable signals + BIT(0) = follow HW0_EN signal + BIT(1) = follow HW1_EN signal + BIT(2) = follow HW2_EN signal + BIT(3) = follow HW3_EN signal + BIT(4) = follow PMIC awake state + +- qcom,vs-soft-start-strength: + Usage: optional + Value type: <u32> + Description: This property sets the soft start strength for voltage + switch type regulators; supported values are: + 0 = 0.05 uA + 1 = 0.25 uA + 2 = 0.55 uA + 3 = 0.75 uA Example: diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index db88feb28c03..24bd422cecd5 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -42,6 +42,7 @@ Optional properties: - regulator-system-load: Load in uA present on regulator that is not captured by any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. +- regulator-over-current-protection: Enable over current protection. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/reset/ath79-reset.txt b/Documentation/devicetree/bindings/reset/ath79-reset.txt new file mode 100644 index 000000000000..4c56330bf398 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/ath79-reset.txt @@ -0,0 +1,20 @@ +Binding for Qualcomm Atheros AR7xxx/AR9XXX reset controller + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required Properties: +- compatible: has to be "qca,<soctype>-reset", "qca,ar7100-reset" + as fallback +- reg: Base address and size of the controllers memory area +- #reset-cells : Specifies the number of cells needed to encode reset + line, should be 1 + +Example: + + reset-controller@1806001c { + compatible = "qca,ar9132-reset", "qca,ar7100-reset"; + reg = <0x1806001c 0x4>; + + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt new file mode 100644 index 000000000000..b4e96a278445 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/nxp,lpc1850-rgu.txt @@ -0,0 +1,84 @@ +NXP LPC1850 Reset Generation Unit (RGU) +======================================== + +Please also refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "nxp,lpc1850-rgu" +- reg: register base and length +- clocks: phandle and clock specifier to RGU clocks +- clock-names: should contain "delay" and "reg" +- #reset-cells: should be 1 + +See table below for valid peripheral reset numbers. Numbers not +in the table below are either reserved or not applicable for +normal operation. + +Reset Peripheral + 9 System control unit (SCU) + 12 ARM Cortex-M0 subsystem core (LPC43xx only) + 13 CPU core + 16 LCD controller + 17 USB0 + 18 USB1 + 19 DMA + 20 SDIO + 21 External memory controller (EMC) + 22 Ethernet + 25 Flash bank A + 27 EEPROM + 28 GPIO + 29 Flash bank B + 32 Timer0 + 33 Timer1 + 34 Timer2 + 35 Timer3 + 36 Repetitive Interrupt timer (RIT) + 37 State Configurable Timer (SCT) + 38 Motor control PWM (MCPWM) + 39 QEI + 40 ADC0 + 41 ADC1 + 42 DAC + 44 USART0 + 45 UART1 + 46 USART2 + 47 USART3 + 48 I2C0 + 49 I2C1 + 50 SSP0 + 51 SSP1 + 52 I2S0 and I2S1 + 53 Serial Flash Interface (SPIFI) + 54 C_CAN1 + 55 C_CAN0 + 56 ARM Cortex-M0 application core (LPC4370 only) + 57 SGPIO (LPC43xx only) + 58 SPI (LPC43xx only) + 60 ADCHS (12-bit ADC) (LPC4370 only) + +Refer to NXP LPC18xx or LPC43xx user manual for more details about +the reset signals and the connected block/peripheral. + +Reset provider example: +rgu: reset-controller@40053000 { + compatible = "nxp,lpc1850-rgu"; + reg = <0x40053000 0x1000>; + clocks = <&cgu BASE_SAFE_CLK>, <&ccu1 CLK_CPU_BUS>; + clock-names = "delay", "reg"; + #reset-cells = <1>; +}; + +Reset consumer example: +mac: ethernet@40010000 { + compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac"; + reg = <0x40010000 0x2000>; + interrupts = <5>; + interrupt-names = "macirq"; + clocks = <&ccu1 CLK_CPU_ETHERNET>; + clock-names = "stmmaceth"; + resets = <&rgu 22>; + reset-names = "stmmaceth"; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/reset/socfpga-reset.txt b/Documentation/devicetree/bindings/reset/socfpga-reset.txt index 32c1c8bfd5dc..98c9f560e5c5 100644 --- a/Documentation/devicetree/bindings/reset/socfpga-reset.txt +++ b/Documentation/devicetree/bindings/reset/socfpga-reset.txt @@ -3,6 +3,7 @@ Altera SOCFPGA Reset Manager Required properties: - compatible : "altr,rst-mgr" - reg : Should contain 1 register ranges(address and length) +- altr,modrst-offset : Should contain the offset of the first modrst register. - #reset-cells: 1 Example: @@ -10,4 +11,5 @@ Example: #reset-cells = <1>; compatible = "altr,rst-mgr"; reg = <0xffd05000 0x1000>; + altr,modrst-offset = <0x10>; }; diff --git a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt index 54ae9f747e45..9ca27761f811 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-picophyreset.txt @@ -39,4 +39,4 @@ Example: }; Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset-controller/stih407-resets.h +include/dt-bindings/reset/stih407-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt index 5ab26b7e9d35..1cfd21d1dfa1 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt @@ -43,5 +43,5 @@ example: Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset-controller/stih415-resets.h -include/dt-bindings/reset-controller/stih416-resets.h +include/dt-bindings/reset/stih415-resets.h +include/dt-bindings/reset/stih416-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt index a8d3d3c25ca2..891a2fd85ed6 100644 --- a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -42,5 +42,5 @@ example: Macro definitions for the supported reset channels can be found in: -include/dt-bindings/reset-controller/stih415-resets.h -include/dt-bindings/reset-controller/stih416-resets.h +include/dt-bindings/reset/stih415-resets.h +include/dt-bindings/reset/stih416-resets.h diff --git a/Documentation/devicetree/bindings/reset/zynq-reset.txt b/Documentation/devicetree/bindings/reset/zynq-reset.txt new file mode 100644 index 000000000000..5860120e3064 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/zynq-reset.txt @@ -0,0 +1,68 @@ +Xilinx Zynq Reset Manager + +The Zynq AP-SoC has several different resets. + +See Chapter 26 of the Zynq TRM (UG585) for more information about Zynq resets. + +Required properties: +- compatible: "xlnx,zynq-reset" +- reg: SLCR offset and size taken via syscon <0x200 0x48> +- syscon: <&slcr> + This should be a phandle to the Zynq's SLCR registers. +- #reset-cells: Must be 1 + +The Zynq Reset Manager needs to be a childnode of the SLCR. + +Example: + rstc: rstc@200 { + compatible = "xlnx,zynq-reset"; + reg = <0x200 0x48>; + #reset-cells = <1>; + syscon = <&slcr>; + }; + +Reset outputs: + 0 : soft reset + 32 : ddr reset + 64 : topsw reset + 96 : dmac reset + 128: usb0 reset + 129: usb1 reset + 160: gem0 reset + 161: gem1 reset + 164: gem0 rx reset + 165: gem1 rx reset + 166: gem0 ref reset + 167: gem1 ref reset + 192: sdio0 reset + 193: sdio1 reset + 196: sdio0 ref reset + 197: sdio1 ref reset + 224: spi0 reset + 225: spi1 reset + 226: spi0 ref reset + 227: spi1 ref reset + 256: can0 reset + 257: can1 reset + 258: can0 ref reset + 259: can1 ref reset + 288: i2c0 reset + 289: i2c1 reset + 320: uart0 reset + 321: uart1 reset + 322: uart0 ref reset + 323: uart1 ref reset + 352: gpio reset + 384: lqspi reset + 385: qspi ref reset + 416: smc reset + 417: smc ref reset + 448: ocm reset + 512: fpga0 out reset + 513: fpga1 out reset + 514: fpga2 out reset + 515: fpga3 out reset + 544: a9 reset 0 + 545: a9 reset 1 + 552: peri reset + diff --git a/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt b/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt index 34c1505774bf..5d3791e789c6 100644 --- a/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt +++ b/Documentation/devicetree/bindings/rtc/atmel,at91rm9200-rtc.txt @@ -5,6 +5,7 @@ Required properties: - reg: physical base address of the controller and length of memory mapped region. - interrupts: rtc alarm/event interrupt +- clocks: phandle to input clock. Example: @@ -12,4 +13,5 @@ rtc@fffffe00 { compatible = "atmel,at91rm9200-rtc"; reg = <0xfffffe00 0x100>; interrupts = <1 4 7>; + clocks = <&clk32k>; }; diff --git a/Documentation/devicetree/bindings/rtc/rtc-mxc.txt b/Documentation/devicetree/bindings/rtc/rtc-mxc.txt new file mode 100644 index 000000000000..5bcd31d995b0 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/rtc-mxc.txt @@ -0,0 +1,26 @@ +* Real Time Clock of the i.MX SoCs + +RTC controller for the i.MX SoCs + +Required properties: +- compatible: Should be "fsl,imx1-rtc" or "fsl,imx21-rtc". +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: IRQ line for the RTC. +- clocks: should contain two entries: + * one for the input reference + * one for the the SoC RTC +- clock-names: should contain: + * "ref" for the input reference clock + * "ipg" for the SoC RTC clock + +Example: + +rtc@10007000 { + compatible = "fsl,imx21-rtc"; + reg = <0x10007000 0x1000>; + interrupts = <22>; + clocks = <&clks IMX27_CLK_CKIL>, + <&clks IMX27_CLK_RTC_IPG_GATE>; + clock-names = "ref", "ipg"; +}; diff --git a/Documentation/devicetree/bindings/rtc/rtc-omap.txt b/Documentation/devicetree/bindings/rtc/rtc-omap.txt index 4ba4dbd34289..43a83668673a 100644 --- a/Documentation/devicetree/bindings/rtc/rtc-omap.txt +++ b/Documentation/devicetree/bindings/rtc/rtc-omap.txt @@ -8,6 +8,7 @@ Required properties: Wakeup generation for event Alarm. It can also be used to control an external PMIC via the pmic_power_en pin. + - "ti,am4372-rtc" - for RTC IP used similar to that on AM437X SoC family. - reg: Address range of rtc register set - interrupts: rtc timer, alarm interrupts in order - interrupt-parent: phandle for the interrupt controller diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt index 90787aa2e648..e6e6142e33ac 100644 --- a/Documentation/devicetree/bindings/serial/atmel-usart.txt +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -22,6 +22,8 @@ Optional properties: memory peripheral interface and USART DMA channel ID, FIFO configuration. Refer to dma.txt and atmel-dma.txt for details. - dma-names: "rx" for RX channel, "tx" for TX channel. +- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO + capable USARTs. <chip> compatible description: - at91rm9200: legacy USART support @@ -57,4 +59,5 @@ Example: dmas = <&dma0 2 0x3>, <&dma0 2 0x204>; dma-names = "tx", "rx"; + atmel,fifo-size = <32>; }; diff --git a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt index ebcbb62c0a76..51b3c9e80ad9 100644 --- a/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt +++ b/Documentation/devicetree/bindings/serial/axis,etraxfs-uart.txt @@ -6,7 +6,7 @@ Required properties: - interrupts: device interrupt Optional properties: -- {dtr,dsr,ri,cd}-gpios: specify a GPIO for DTR/DSR/RI/CD +- {dtr,dsr,rng,dcd}-gpios: specify a GPIO for DTR/DSR/RI/DCD line respectively. Example: @@ -16,4 +16,8 @@ serial@b00260000 { reg = <0xb0026000 0x1000>; interrupts = <68>; status = "disabled"; + dtr-gpios = <&sysgpio 0 GPIO_ACTIVE_LOW>; + dsr-gpios = <&sysgpio 1 GPIO_ACTIVE_LOW>; + rng-gpios = <&sysgpio 2 GPIO_ACTIVE_LOW>; + dcd-gpios = <&sysgpio 3 GPIO_ACTIVE_LOW>; }; diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt index 8d63f1da07aa..2d47add34765 100644 --- a/Documentation/devicetree/bindings/serial/mtk-uart.txt +++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt @@ -5,10 +5,12 @@ Required properties: * "mediatek,mt8135-uart" for MT8135 compatible UARTS * "mediatek,mt8127-uart" for MT8127 compatible UARTS * "mediatek,mt8173-uart" for MT8173 compatible UARTS + * "mediatek,mt6795-uart" for MT6795 compatible UARTS * "mediatek,mt6589-uart" for MT6589 compatible UARTS * "mediatek,mt6582-uart" for MT6582 compatible UARTS - * "mediatek,mt6577-uart" for all compatible UARTS (MT8173, MT6589, MT6582, - MT6577) + * "mediatek,mt6580-uart" for MT6580 compatible UARTS + * "mediatek,mt6577-uart" for all compatible UARTS (MT8173, MT6795, + MT6589, MT6582, MT6580, MT6577) - reg: The base address of the UART register bank. diff --git a/Documentation/devicetree/bindings/serial/omap_serial.txt b/Documentation/devicetree/bindings/serial/omap_serial.txt index 54c2a155c783..7a71b5de77d6 100644 --- a/Documentation/devicetree/bindings/serial/omap_serial.txt +++ b/Documentation/devicetree/bindings/serial/omap_serial.txt @@ -4,6 +4,9 @@ Required properties: - compatible : should be "ti,omap2-uart" for OMAP2 controllers - compatible : should be "ti,omap3-uart" for OMAP3 controllers - compatible : should be "ti,omap4-uart" for OMAP4 controllers +- compatible : should be "ti,am4372-uart" for AM437x controllers +- compatible : should be "ti,am3352-uart" for AM335x controllers +- compatible : should be "ti,dra742-uart" for DRA7x controllers - reg : address and length of the register space - interrupts or interrupts-extended : Should contain the uart interrupt specifier or both the interrupt diff --git a/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt new file mode 100644 index 000000000000..c0511142b39c --- /dev/null +++ b/Documentation/devicetree/bindings/soc/mediatek/scpsys.txt @@ -0,0 +1,41 @@ +MediaTek SCPSYS +=============== + +The System Control Processor System (SCPSYS) has several power management +related tasks in the system. The tasks include thermal measurement, dynamic +voltage frequency scaling (DVFS), interrupt filter and lowlevel sleep control. +The System Power Manager (SPM) inside the SCPSYS is for the MTCMOS power +domain control. + +The driver implements the Generic PM domain bindings described in +power/power_domain.txt. It provides the power domains defined in +include/dt-bindings/power/mt8173-power.h. + +Required properties: +- compatible: Must be "mediatek,mt8173-scpsys" +- #power-domain-cells: Must be 1 +- reg: Address range of the SCPSYS unit +- infracfg: must contain a phandle to the infracfg controller +- clock, clock-names: clocks according to the common clock binding. + The clocks needed "mm" and "mfg". These are the + clocks which hardware needs to be enabled before + enabling certain power domains. + +Example: + + scpsys: scpsys@10006000 { + #power-domain-cells = <1>; + compatible = "mediatek,mt8173-scpsys"; + reg = <0 0x10006000 0 0x1000>; + infracfg = <&infracfg>; + clocks = <&clk26m>, + <&topckgen CLK_TOP_MM_SEL>; + clock-names = "mfg", "mm"; + }; + +Example consumer: + + afe: mt8173-afe-pcm@11220000 { + compatible = "mediatek,mt8173-afe-pcm"; + power-domains = <&scpsys MT8173_POWER_DOMAIN_AUDIO>; + }; diff --git a/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt b/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt new file mode 100644 index 000000000000..e27f5c4c54fd --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom,smd-rpm.txt @@ -0,0 +1,117 @@ +Qualcomm Resource Power Manager (RPM) over SMD + +This driver is used to interface with the Resource Power Manager (RPM) found in +various Qualcomm platforms. The RPM allows each component in the system to vote +for state of the system resources, such as clocks, regulators and bus +frequencies. + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-msm8974" + +- qcom,smd-channels: + Usage: required + Value type: <stringlist> + Definition: Shared Memory channel used for communication with the RPM + += SUBDEVICES + +The RPM exposes resources to its subnodes. The below bindings specify the set +of valid subnodes that can operate on these resources. + +== Regulators + +Regulator nodes are identified by their compatible: + +- compatible: + Usage: required + Value type: <string> + Definition: must be one of: + "qcom,rpm-pm8841-regulators" + "qcom,rpm-pm8941-regulators" + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_s4-supply: +- vdd_s5-supply: +- vdd_s6-supply: +- vdd_s7-supply: +- vdd_s8-supply: + Usage: optional (pm8841 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +- vdd_s1-supply: +- vdd_s2-supply: +- vdd_s3-supply: +- vdd_l1_l3-supply: +- vdd_l2_lvs1_2_3-supply: +- vdd_l4_l11-supply: +- vdd_l5_l7-supply: +- vdd_l6_l12_l14_l15-supply: +- vdd_l8_l16_l18_l19-supply: +- vdd_l9_l10_l17_l22-supply: +- vdd_l13_l20_l23_l24-supply: +- vdd_l21-supply: +- vin_5vs-supply: + Usage: optional (pm8941 only) + Value type: <phandle> + Definition: reference to regulator supplying the input pin, as + described in the data sheet + +The regulator node houses sub-nodes for each regulator within the device. Each +sub-node is identified using the node's name, with valid values listed for each +of the pmics below. + +pm8841: + s1, s2, s3, s4, s5, s6, s7, s8 + +pm8941: + s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, + l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, + lvs3, 5vs1, 5vs2 + +The content of each sub-node is defined by the standard binding for regulators - +see regulator.txt. + += EXAMPLE + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8974"; + qcom,smd-channels = "rpm_requests"; + + pm8941-regulators { + compatible = "qcom,rpm-pm8941-regulators"; + vdd_l13_l20_l23_l24-supply = <&pm8941_boost>; + + pm8941_s3: s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8941_boost: s4 { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + pm8941_l20: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + }; + }; + }; + }; + }; + diff --git a/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt new file mode 100644 index 000000000000..f65c76db9859 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/qcom/qcom,smd.txt @@ -0,0 +1,79 @@ +Qualcomm Shared Memory Driver (SMD) binding + +This binding describes the Qualcomm Shared Memory Driver, a fifo based +communication channel for sending data between the various subsystems in +Qualcomm platforms. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,smd" + += EDGES + +Each subnode of the SMD node represents a remote subsystem or a remote +processor of some sort - or in SMD language an "edge". The name of the edges +are not important. +The edge is described by the following properties: + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the IRQ used by the remote processor to + signal this processor about communication related updates + +- qcom,ipc: + Usage: required + Value type: <prop-encoded-array> + Definition: three entries specifying the outgoing ipc bit used for + signaling the remote processor: + - phandle to a syscon node representing the apcs registers + - u32 representing offset to the register within the syscon + - u32 representing the ipc bit within the register + +- qcom,smd-edge: + Usage: required + Value type: <u32> + Definition: the identifier of the remote processor in the smd channel + allocation table + += SMD DEVICES + +In turn, subnodes of the "edges" represent devices tied to SMD channels on that +"edge". The names of the devices are not important. The properties of these +nodes are defined by the individual bindings for the SMD devices - but must +contain the following property: + +- qcom,smd-channels: + Usage: required + Value type: <stringlist> + Definition: a list of channels tied to this device, used for matching + the device to channels + += EXAMPLE + +The following example represents a smd node, with one edge representing the +"rpm" subsystem. For the "rpm" subsystem we have a device tied to the +"rpm_request" channel. + + apcs: syscon@f9011000 { + compatible = "syscon"; + reg = <0xf9011000 0x1000>; + }; + + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8974"; + qcom,smd-channels = "rpm_requests"; + + ... + }; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt index 13e2ef496724..275c6ea356f6 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra30-hda.txt @@ -8,10 +8,10 @@ Required properties: - interrupts : The interrupt from the HDA controller. - clocks : Must contain an entry for each required entry in clock-names. See ../clocks/clock-bindings.txt for details. -- clock-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi +- clock-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x - resets : Must contain an entry for each entry in reset-names. See ../reset/reset.txt for details. -- reset-names : Must include the following entries: hda, hdacodec_2x, hda2hdmi +- reset-names : Must include the following entries: hda, hda2hdmi, hda2codec_2x Example: @@ -24,7 +24,7 @@ hda@0,70030000 { <&tegra_car TEGRA124_CLK_HDA2CODEC_2X>; clock-names = "hda", "hda2hdmi", "hda2codec_2x"; resets = <&tegra_car 125>, /* hda */ - <&tegra_car 128>; /* hda2hdmi */ - <&tegra_car 111>, /* hda2codec_2x */ + <&tegra_car 128>, /* hda2hdmi */ + <&tegra_car 111>; /* hda2codec_2x */ reset-names = "hda", "hda2hdmi", "hda2codec_2x"; }; diff --git a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt index bd99193e87b9..204b311e0400 100644 --- a/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt +++ b/Documentation/devicetree/bindings/spi/snps,dw-apb-ssi.txt @@ -10,6 +10,8 @@ Required properties: Optional properties: - cs-gpios : Specifies the gpio pis to be used for chipselects. - num-cs : The number of chipselects. If omitted, this will default to 4. +- reg-io-width : The I/O register width (in bytes) implemented by this + device. Supported values are 2 or 4 (the default). Child nodes as per the generic SPI binding. diff --git a/Documentation/devicetree/bindings/spi/spi-davinci.txt b/Documentation/devicetree/bindings/spi/spi-davinci.txt index 12ecfe9e3599..d1e914adcf6e 100644 --- a/Documentation/devicetree/bindings/spi/spi-davinci.txt +++ b/Documentation/devicetree/bindings/spi/spi-davinci.txt @@ -12,6 +12,8 @@ Required properties: - compatible: - "ti,dm6441-spi" for SPI used similar to that on DM644x SoC family - "ti,da830-spi" for SPI used similar to that on DA8xx SoC family + - "ti,keystone-spi" for SPI used similar to that on Keystone2 SoC + family - reg: Offset and length of SPI controller register space - num-cs: Number of chip selects. This includes internal as well as GPIO chip selects. diff --git a/Documentation/devicetree/bindings/spi/spi-img-spfi.txt b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt index e02fbf18c82c..494db6012d02 100644 --- a/Documentation/devicetree/bindings/spi/spi-img-spfi.txt +++ b/Documentation/devicetree/bindings/spi/spi-img-spfi.txt @@ -21,6 +21,7 @@ Required properties: Optional properties: - img,supports-quad-mode: Should be set if the interface supports quad mode SPI transfers. +- spfi-max-frequency: Maximum speed supported by the spfi block. Example: diff --git a/Documentation/devicetree/bindings/spi/spi-mt65xx.txt b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt new file mode 100644 index 000000000000..dcefc438272f --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-mt65xx.txt @@ -0,0 +1,51 @@ +Binding for MTK SPI controller + +Required properties: +- compatible: should be one of the following. + - mediatek,mt8173-spi: for mt8173 platforms + - mediatek,mt8135-spi: for mt8135 platforms + - mediatek,mt6589-spi: for mt6589 platforms + +- #address-cells: should be 1. + +- #size-cells: should be 0. + +- reg: Address and length of the register set for the device + +- interrupts: Should contain spi interrupt + +- clocks: phandles to input clocks. + The first should be <&topckgen CLK_TOP_SPI_SEL>. + The second should be one of the following. + - <&clk26m>: specify parent clock 26MHZ. + - <&topckgen CLK_TOP_SYSPLL3_D2>: specify parent clock 109MHZ. + It's the default one. + - <&topckgen CLK_TOP_SYSPLL4_D2>: specify parent clock 78MHZ. + - <&topckgen CLK_TOP_UNIVPLL2_D4>: specify parent clock 104MHZ. + - <&topckgen CLK_TOP_UNIVPLL1_D8>: specify parent clock 78MHZ. + +- clock-names: shall be "spi-clk" for the controller clock, and + "parent-clk" for the parent clock. + +Optional properties: +- mediatek,pad-select: specify which pins group(ck/mi/mo/cs) spi + controller used, this value should be 0~3, only required for MT8173. + 0: specify GPIO69,70,71,72 for spi pins. + 1: specify GPIO102,103,104,105 for spi pins. + 2: specify GPIO128,129,130,131 for spi pins. + 3: specify GPIO5,6,7,8 for spi pins. + +Example: + +- SoC Specific Portion: +spi: spi@1100a000 { + compatible = "mediatek,mt8173-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x1100a000 0 0x1000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_SPI_SEL>, <&topckgen CLK_TOP_SYSPLL3_D2>; + clock-names = "spi-clk", "parent-clk"; + mediatek,pad-select = <0>; + status = "disabled"; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-xlp.txt b/Documentation/devicetree/bindings/spi/spi-xlp.txt new file mode 100644 index 000000000000..40e82d51efec --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xlp.txt @@ -0,0 +1,39 @@ +SPI Master controller for Netlogic XLP MIPS64 SOCs +================================================== + +Currently this SPI controller driver is supported for the following +Netlogic XLP SoCs: + XLP832, XLP316, XLP208, XLP980, XLP532 + +Required properties: +- compatible : Should be "netlogic,xlp832-spi". +- #address-cells : Number of cells required to define a chip select address + on the SPI bus. +- #size-cells : Should be zero. +- reg : Should contain register location and length. +- clocks : Phandle of the spi clock +- interrupts : Interrupt number used by this controller. +- interrupt-parent : Phandle of the parent interrupt controller. + +SPI slave nodes must be children of the SPI master node and can contain +properties described in Documentation/devicetree/bindings/spi/spi-bus.txt. + +Example: + + spi: xlp_spi@3a100 { + compatible = "netlogic,xlp832-spi"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0 0x3a100 0x100>; + clocks = <&spi_clk>; + interrupts = <34>; + interrupt-parent = <&pic>; + + spi_nor@1 { + compatible = "spansion,s25sl12801"; + #address-cells = <1>; + #size-cells = <1>; + reg = <1>; /* Chip Select */ + spi-max-frequency = <40000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt index 307537787574..555fb117d4fa 100644 --- a/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt +++ b/Documentation/devicetree/bindings/staging/iio/adc/mxs-lradc.txt @@ -1,4 +1,4 @@ -* Freescale i.MX28 LRADC device driver +* Freescale MXS LRADC device driver Required properties: - compatible: Should be "fsl,imx23-lradc" for i.MX23 SoC and "fsl,imx28-lradc" diff --git a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt index 7c4408ff4b83..53a3029b7589 100644 --- a/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt +++ b/Documentation/devicetree/bindings/timer/mediatek,mtk-timer.txt @@ -2,7 +2,11 @@ Mediatek MT6577, MT6572 and MT6589 Timers --------------------------------------- Required properties: -- compatible: Should be "mediatek,mt6577-timer" +- compatible should contain: + * "mediatek,mt6589-timer" for MT6589 compatible timers + * "mediatek,mt6580-timer" for MT6580 compatible timers + * "mediatek,mt6577-timer" for all compatible timers (MT6589, MT6580, + MT6577) - reg: Should contain location and length for timers register. - clocks: Clocks driving the timer hardware. This list should include two clocks. The order is system clock and as second clock the RTC clock. diff --git a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt new file mode 100644 index 000000000000..862cd7c79805 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt @@ -0,0 +1,29 @@ +Allwinner sun4i A10 musb DRC/OTG controller +------------------------------------------- + +Required properties: + - compatible : "allwinner,sun4i-a10-musb", "allwinner,sun6i-a31-musb" + or "allwinner,sun8i-a33-musb" + - reg : mmio address range of the musb controller + - clocks : clock specifier for the musb controller ahb gate clock + - reset : reset specifier for the ahb reset (A31 and newer only) + - interrupts : interrupt to which the musb controller is connected + - interrupt-names : must be "mc" + - phys : phy specifier for the otg phy + - phy-names : must be "usb" + - dr_mode : Dual-Role mode must be "host" or "otg" + - extcon : extcon specifier for the otg phy + +Example: + + usb_otg: usb@01c13000 { + compatible = "allwinner,sun4i-a10-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ahb_gates 0>; + interrupts = <38>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + status = "disabled"; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 553e2fae3a76..d71ef07bca5d 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -30,6 +30,21 @@ Optional properties: argument that indicate usb controller index - disable-over-current: (FSL only) disable over current detect - external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus +- itc-setting: interrupt threshold control register control, the setting + should be aligned with ITC bits at register USBCMD. +- ahb-burst-config: it is vendor dependent, the required value should be + aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This + property is used to change AHB burst configuration, check the chipidea + spec for meaning of each value. If this property is not existed, it + will use the reset value. +- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from system memory to the USB + bus, changing this value takes effect only the SBUSCFG.AHBBRST is 0. +- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from the USB bus to system memory, + changing this value takes effect only the SBUSCFG.AHBBRST is 0. Example: @@ -41,4 +56,9 @@ Example: phys = <&usb_phy0>; phy-names = "usb-phy"; vbus-supply = <®_usb0_vbus>; + gadget-itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; }; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt index 477d5bb5e51c..bba825711873 100644 --- a/Documentation/devicetree/bindings/usb/generic.txt +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -11,6 +11,19 @@ Optional properties: "peripheral" and "otg". In case this attribute isn't passed via DT, USB DRD controllers should default to OTG. + - otg-rev: tells usb driver the release number of the OTG and EH supplement + with which the device and its descriptors are compliant, + in binary-coded decimal (i.e. 2.0 is 0200H). This + property is used if any real OTG features(HNP/SRP/ADP) + is enabled, if ADP is required, otg-rev should be + 0x0200 or above. + - hnp-disable: tells OTG controllers we want to disable OTG HNP, normally HNP + is the basic function of real OTG except you want it + to be a srp-capable only B device. + - srp-disable: tells OTG controllers we want to disable OTG SRP, SRP is + optional for OTG device. + - adp-disable: tells OTG controllers we want to disable OTG ADP, ADP is + optional for OTG device. This is an attribute to a USB controller such as: @@ -21,4 +34,6 @@ dwc3@4a030000 { usb-phy = <&usb2_phy>, <&usb3,phy>; maximum-speed = "super-speed"; dr_mode = "otg"; + otg-rev = <0x0200>; + adp-disable; }; diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt index bd8d9e753029..8654a3ec23e4 100644 --- a/Documentation/devicetree/bindings/usb/msm-hsusb.txt +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -52,6 +52,10 @@ Required properties: Optional properties: - dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" +- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual + SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex + D+/D- USB lines between connectors. + - qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device Mode Eye Diagram test. Start address at which these values will be written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as diff --git a/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt new file mode 100644 index 000000000000..2cb2168cef41 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/qcom,usb-8x16-phy.txt @@ -0,0 +1,76 @@ +Qualcomm's APQ8016/MSM8916 USB transceiver controller + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-8x16-phy". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: USB PHY base address and length of the register map + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: See clock-bindings.txt section "consumers". List of + two clock specifiers for interface and core controller + clocks. + +- clock-names: + Usage: required + Value type: <string> + Definition: Must contain "iface" and "core" strings. + +- vddcx-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator VDCCX supply node. + +- v1p8-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator 1.8V supply node. + +- v3p3-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator 3.3V supply node. + +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: See reset.txt section "consumers". PHY reset specifier. + +- reset-names: + Usage: required + Value type: <string> + Definition: Must contain "phy" string. + +- switch-gpio: + Usage: optional + Value type: <prop-encoded-array> + Definition: Some boards are using Dual SPDT USB Switch, witch is + controlled by GPIO to de/multiplex D+/D- USB lines + between connectors. + +Example: + usb_phy: phy@78d9000 { + compatible = "qcom,usb-8x16-phy"; + reg = <0x78d9000 0x400>; + + vddcx-supply = <&pm8916_s1_corner>; + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + + clocks = <&gcc GCC_USB_HS_AHB_CLK>, + <&gcc GCC_USB_HS_SYSTEM_CLK>; + clock-names = "iface", "core"; + + resets = <&gcc GCC_USB2A_PHY_BCR>; + reset-names = "phy"; + + // D+/D- lines: 1 - Routed to HUB, 0 - Device connector + switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + }; + diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index d444757c4d9e..56a6d4e79383 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -46,6 +46,7 @@ chipone ChipOne chipspark ChipSPARK chrp Common Hardware Reference Platform chunghwa Chunghwa Picture Tubes Ltd. +ciaa Computadora Industrial Abierta Argentina cirrus Cirrus Logic, Inc. cloudengines Cloud Engines, Inc. cnm Chips&Media, Inc. @@ -112,6 +113,7 @@ intel Intel Corporation intercontrol Inter Control Group isee ISEE 2007 S.L. isil Intersil +jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH kinetic Kinetic Technologies @@ -135,6 +137,7 @@ mitsubishi Mitsubishi Electric Corporation mosaixtech Mosaix Technologies, Inc. moxa Moxa mpl MPL AG +msi Micro-Star International Co. Ltd. mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) mundoreader Mundo Reader S.L. murata Murata Manufacturing Co., Ltd. @@ -143,6 +146,7 @@ national National Semiconductor neonode Neonode Inc. netgear NETGEAR netlogic Broadcom Corporation (formerly NetLogic Microsystems) +netxeon Shenzhen Netxeon Technology CO., LTD newhaven Newhaven Display International nintendo Nintendo nokia Nokia @@ -181,6 +185,7 @@ sbs Smart Battery System schindler Schindler seagate Seagate Technology PLC semtech Semtech Corporation +sharp Sharp Corporation sil Silicon Image silabs Silicon Laboratories siliconmitus Silicon Mitus, Inc. diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt index a4d869744f59..86fa6de1019b 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -6,6 +6,7 @@ Required properties: - compatible: must be "atmel,at91sam9260-wdt". - reg: physical base address of the controller and length of memory mapped region. +- clocks: phandle to input clock. Optional properties: - timeout-sec: contains the watchdog timeout in seconds. @@ -39,6 +40,7 @@ Example: compatible = "atmel,at91sam9260-wdt"; reg = <0xfffffd40 0x10>; interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + clocks = <&clk32k>; timeout-sec = <15>; atmel,watchdog-type = "hardware"; atmel,reset-type = "all"; |