diff options
Diffstat (limited to 'Documentation/devicetree')
22 files changed, 652 insertions, 47 deletions
diff --git a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt index 6b458bb2440d..f2aab3dc2b52 100644 --- a/Documentation/devicetree/bindings/crypto/atmel-crypto.txt +++ b/Documentation/devicetree/bindings/crypto/atmel-crypto.txt @@ -66,16 +66,3 @@ sha@f8034000 { dmas = <&dma1 2 17>; dma-names = "tx"; }; - -* Eliptic Curve Cryptography (I2C) - -Required properties: -- compatible : must be "atmel,atecc508a". -- reg: I2C bus address of the device. -- clock-frequency: must be present in the i2c controller node. - -Example: -atecc508a@c0 { - compatible = "atmel,atecc508a"; - reg = <0xC0>; -}; diff --git a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt index 69da2115abdc..1cf6182f888c 100644 --- a/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt +++ b/Documentation/devicetree/bindings/i3c/cdns,i3c-master.txt @@ -38,6 +38,6 @@ Example: nunchuk: nunchuk@52 { compatible = "nintendo,nunchuk"; - reg = <0x52 0x80000010 0>; + reg = <0x52 0x0 0x10>; }; }; diff --git a/Documentation/devicetree/bindings/i3c/i3c.txt b/Documentation/devicetree/bindings/i3c/i3c.txt index ab729a0a86ae..4ffe059f0fec 100644 --- a/Documentation/devicetree/bindings/i3c/i3c.txt +++ b/Documentation/devicetree/bindings/i3c/i3c.txt @@ -39,7 +39,9 @@ valid here, but several new properties have been added. New constraint on existing properties: -------------------------------------- - reg: contains 3 cells - + first cell : still encoding the I2C address + + first cell : still encoding the I2C address. 10 bit addressing is not + supported. Devices with 10 bit address can't be properly passed through + DEFSLVS command. + second cell: shall be 0 diff --git a/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt b/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt new file mode 100644 index 000000000000..4e82fd575cec --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/amazon,al-fic.txt @@ -0,0 +1,29 @@ +Amazon's Annapurna Labs Fabric Interrupt Controller + +Required properties: + +- compatible: should be "amazon,al-fic" +- reg: physical base address and size of the registers +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: must be 2. + First cell defines the index of the interrupt within the controller. + Second cell is used to specify the trigger type and must be one of the + following: + - bits[3:0] trigger type and level flags + 1 = low-to-high edge triggered + 4 = active high level-sensitive +- interrupt-parent: specifies the parent interrupt controller. +- interrupts: describes which input line in the interrupt parent, this + fic's output is connected to. This field property depends on the parent's + binding + +Example: + +amazon_fic: interrupt-controller@0xfd8a8500 { + compatible = "amazon,al-fic"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x0 0xfd8a8500 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 0x0 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt index 1502a51548bb..7d531d5fff29 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt @@ -15,6 +15,7 @@ Required properties: "amlogic,meson-gxbb-gpio-intc" for GXBB SoCs (S905) or "amlogic,meson-gxl-gpio-intc" for GXL SoCs (S905X, S912) "amlogic,meson-axg-gpio-intc" for AXG SoCs (A113D, A113X) + "amlogic,meson-g12a-gpio-intc" for G12A SoCs (S905D2, S905X2, S905Y2) - reg : Specifies base physical address and size of the registers. - interrupt-controller : Identifies the node as an interrupt controller. - #interrupt-cells : Specifies the number of cells needed to encode an diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt index ab921f1698fb..e13405355166 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt @@ -6,11 +6,16 @@ C-SKY Multi-processors Interrupt Controller is designed for ck807/ck810/ck860 SMP soc, and it also could be used in non-SMP system. Interrupt number definition: - 0-15 : software irq, and we use 15 as our IPI_IRQ. 16-31 : private irq, and we use 16 as the co-processor timer. 31-1024: common irq for soc ip. +Interrupt triger mode: (Defined in dt-bindings/interrupt-controller/irq.h) + IRQ_TYPE_LEVEL_HIGH (default) + IRQ_TYPE_LEVEL_LOW + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + ============================= intc node bindings definition ============================= @@ -26,15 +31,22 @@ intc node bindings definition - #interrupt-cells Usage: required Value type: <u32> - Definition: must be <1> + Definition: <2> - interrupt-controller: Usage: required -Examples: +Examples: ("interrupts = <irq_num IRQ_TYPE_XXX>") --------- +#include <dt-bindings/interrupt-controller/irq.h> intc: interrupt-controller { compatible = "csky,mpintc"; - #interrupt-cells = <1>; + #interrupt-cells = <2>; interrupt-controller; }; + + device: device-example { + ... + interrupts = <34 IRQ_TYPE_EDGE_RISING>; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt new file mode 100644 index 000000000000..727b7e4cd6e0 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/renesas,rza1-irqc.txt @@ -0,0 +1,43 @@ +DT bindings for the Renesas RZ/A1 Interrupt Controller + +The RZ/A1 Interrupt Controller is a front-end for the GIC found on Renesas +RZ/A1 and RZ/A2 SoCs: + - IRQ sense select for 8 external interrupts, 1:1-mapped to 8 GIC SPI + interrupts, + - NMI edge select. + +Required properties: + - compatible: Must be "renesas,<soctype>-irqc", and "renesas,rza1-irqc" as + fallback. + Examples with soctypes are: + - "renesas,r7s72100-irqc" (RZ/A1H) + - "renesas,r7s9210-irqc" (RZ/A2M) + - #interrupt-cells: Must be 2 (an interrupt index and flags, as defined + in interrupts.txt in this directory) + - #address-cells: Must be zero + - interrupt-controller: Marks the device as an interrupt controller + - reg: Base address and length of the memory resource used by the interrupt + controller + - interrupt-map: Specifies the mapping from external interrupts to GIC + interrupts + - interrupt-map-mask: Must be <7 0> + +Example: + + irqc: interrupt-controller@fcfef800 { + compatible = "renesas,r7s72100-irqc", "renesas,rza1-irqc"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0xfcfef800 0x6>; + interrupt-map = + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <7 0>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-lm36274.txt b/Documentation/devicetree/bindings/leds/leds-lm36274.txt new file mode 100644 index 000000000000..39c230d59a4d --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm36274.txt @@ -0,0 +1,85 @@ +* Texas Instruments LM36274 4-Channel LCD Backlight Driver w/Integrated Bias + +The LM36274 is an integrated four-channel WLED driver and LCD bias supply. +The backlight boost provides the power to bias four parallel LED strings with +up to 29V total output voltage. The 11-bit LED current is programmable via +the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA. + +Parent device properties are documented in +Documentation/devicetree/bindings/mfd/ti-lmu.txt + +Regulator properties are documented in +Documentation/devicetree/bindings/regulator/lm363x-regulator.txt + +Required backlight properties: + - compatible: + "ti,lm36274-backlight" + - reg : 0 + - #address-cells : 1 + - #size-cells : 0 + - led-sources : Indicates which LED strings will be enabled. + Values from 0-3, sources is 0 based so strings will be + source value + 1. + +Optional backlight properties: + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; + + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; + + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + }; + + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; + }; +}; + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm36274.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-lm3697.txt b/Documentation/devicetree/bindings/leds/leds-lm3697.txt new file mode 100644 index 000000000000..63992d732959 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-lm3697.txt @@ -0,0 +1,73 @@ +* Texas Instruments - LM3697 Highly Efficient White LED Driver + +The LM3697 11-bit LED driver provides high- +performance backlight dimming for 1, 2, or 3 series +LED strings while delivering up to 90% efficiency. + +This device is suitable for display and keypad lighting + +Required properties: + - compatible: + "ti,lm3697" + - reg : I2C slave address + - #address-cells : 1 + - #size-cells : 0 + +Optional properties: + - enable-gpios : GPIO pin to enable/disable the device + - vled-supply : LED supply + +Required child properties: + - reg : 0 - LED is Controlled by bank A + 1 - LED is Controlled by bank B + - led-sources : Indicates which HVLED string is associated to which + control bank. This is a zero based property so + HVLED1 = 0, HVLED2 = 1, HVLED3 = 2. + Additional information is contained + in Documentation/devicetree/bindings/leds/common.txt + +Optional child properties: + - ti,brightness-resolution - see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-up-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - ramp-down-us: see Documentation/devicetree/bindings/mfd/ti-lmu.txt + - label : see Documentation/devicetree/bindings/leds/common.txt + - linux,default-trigger : + see Documentation/devicetree/bindings/leds/common.txt + +Example: + +HVLED string 1 and 3 are controlled by control bank A and HVLED 2 string is +controlled by control bank B. + +led-controller@36 { + compatible = "ti,lm3697"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x36>; + + enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; + vled-supply = <&vbatt>; + + led@0 { + reg = <0>; + led-sources = <0 2>; + ti,brightness-resolution = <2047>; + ramp-up-us = <5000>; + ramp-down-us = <1000>; + label = "white:first_backlight_cluster"; + linux,default-trigger = "backlight"; + }; + + led@1 { + reg = <1>; + led-sources = <1>; + ti,brightness-resolution = <255>; + ramp-up-us = <500>; + ramp-down-us = <1000>; + label = "white:second_backlight_cluster"; + linux,default-trigger = "backlight"; + }; +} + +For more product information please see the link below: +http://www.ti.com/lit/ds/symlink/lm3697.pdf diff --git a/Documentation/devicetree/bindings/leds/leds-spi-byte.txt b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt new file mode 100644 index 000000000000..28b6b2d9091e --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-spi-byte.txt @@ -0,0 +1,44 @@ +* Single Byte SPI LED Device Driver. + +The driver can be used for controllers with a very simple SPI protocol: +- one LED is controlled by a single byte on MOSI +- the value of the byte gives the brightness between two values (lowest to + highest) +- no return value is necessary (no MISO signal) + +The value for lowest and highest brightness is dependent on the device and +therefore on the compatible string. + +Depending on the compatible string some special functions (like hardware +accelerated blinking) might can be supported too. + +The driver currently only supports one LED. The properties of the LED are +configured in a sub-node in the device node. + +Required properties: +- compatible: should be one of + * "ubnt,acb-spi-led" microcontroller (SONiX 8F26E611LA) based device + used for example in Ubiquiti airCube ISP + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. + +LED sub-node properties: +- label: + see Documentation/devicetree/bindings/leds/common.txt +- default-state: + see Documentation/devicetree/bindings/leds/common.txt + Only "on" and "off" are supported. + +Example: + +led-controller@0 { + compatible = "ubnt,acb-spi-led"; + reg = <0>; + spi-max-frequency = <100000>; + + led { + label = "white:status"; + default-state = "on"; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt index 86ca786d54fc..2296b8f24de4 100644 --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt @@ -8,7 +8,7 @@ TI LMU driver supports lighting devices below. LM3632 Backlight and regulator LM3633 Backlight, LED and fault monitor LM3695 Backlight - LM3697 Backlight and fault monitor + LM36274 Backlight and regulator Required properties: - compatible: Should be one of: @@ -16,15 +16,32 @@ Required properties: "ti,lm3632" "ti,lm3633" "ti,lm3695" - "ti,lm3697" + "ti,lm36274" - reg: I2C slave address. 0x11 for LM3632 0x29 for LM3631 - 0x36 for LM3633, LM3697 + 0x36 for LM3633 0x63 for LM3695 + 0x11 for LM36274 -Optional property: +Optional properties: - enable-gpios: A GPIO specifier for hardware enable pin. + - ramp-up-us: Current ramping from one brightness level to + the a higher brightness level. + Range from 2048 us - 117.44 s + - ramp-down-us: Current ramping from one brightness level to + the a lower brightness level. + Range from 2048 us - 117.44 s + - ti,brightness-resolution - This determines whether to use 8 bit brightness + mode or 11 bit brightness mode. If this value is + not set the device is defaulted to the preferred + 8bit brightness mode per 7.3.4.1 of the data + sheet. This setting can either be in the parent + node or as part of the LED child nodes. This + is determined by the part itself if the strings + have a common brightness register or individual + brightness registers. + The values are 255 (8bit) or 2047 (11bit). Required node: - backlight: All LMU devices have backlight child nodes. @@ -35,14 +52,15 @@ Optional nodes: Required properties: - compatible: Should be one of: "ti,lm3633-fault-monitor" - "ti,lm3697-fault-monitor" - leds: LED properties for LM3633. Please refer to [2]. + LED properties for LM36274. Please refer to [4]. - regulators: Regulator properties for LM3631 and LM3632. Please refer to [3]. [1] ../leds/backlight/ti-lmu-backlight.txt [2] ../leds/leds-lm3633.txt [3] ../regulator/lm363x-regulator.txt +[4] ../leds/leds-lm36274.txt lm3631@29 { compatible = "ti,lm3631"; @@ -90,7 +108,7 @@ lm3631@29 { lcd_bl { led-sources = <0 1>; - ramp-up-msec = <300>; + ramp-up-us = <300000>; }; }; }; @@ -152,15 +170,15 @@ lm3633@36 { main { label = "main_lcd"; led-sources = <1 2>; - ramp-up-msec = <500>; - ramp-down-msec = <500>; + ramp-up-us = <500000>; + ramp-down-us = <500000>; }; front { label = "front_lcd"; led-sources = <0>; - ramp-up-msec = <1000>; - ramp-down-msec = <0>; + ramp-up-us = <1000000>; + ramp-down-us = <0>; }; }; @@ -201,23 +219,51 @@ lm3695@63 { }; }; -lm3697@36 { - compatible = "ti,lm3697"; - reg = <0x36>; +lm36274@11 { + compatible = "ti,lm36274"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11>; enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>; + regulators { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm363x-regulator"; - backlight { - compatible = "ti,lm3697-backlight"; + enable-gpios = <&pioC 0 GPIO_ACTIVE_HIGH>, + <&pioC 1 GPIO_ACTIVE_HIGH>; - lcd { - led-sources = <0 1 2>; - ramp-up-msec = <200>; - ramp-down-msec = <200>; + vboost { + regulator-name = "lcd_boost"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <7150000>; + regulator-always-on; + }; + + vpos { + regulator-name = "lcd_vpos"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; + }; + + vneg { + regulator-name = "lcd_vneg"; + regulator-min-microvolt = <4000000>; + regulator-max-microvolt = <6500000>; }; }; - fault-monitor { - compatible = "ti,lm3697-fault-monitor"; + backlight { + #address-cells = <1>; + #size-cells = <0>; + compatible = "ti,lm36274-backlight"; + + led@0 { + reg = <0>; + led-sources = <0 2>; + label = "white:backlight_cluster"; + linux,default-trigger = "backlight"; + }; }; }; diff --git a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt index 188c8bd4eb67..5a0111d4de58 100644 --- a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt +++ b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt @@ -4,6 +4,7 @@ Required properties: - compatible: Should be one of the following: - "microchip,mcp2510" for MCP2510. - "microchip,mcp2515" for MCP2515. + - "microchip,mcp25625" for MCP25625. - reg: SPI chip select. - clocks: The clock feeding the CAN controller. - interrupts: Should contain IRQ line for the CAN controller. diff --git a/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt new file mode 100644 index 000000000000..d77e3f26f9e6 --- /dev/null +++ b/Documentation/devicetree/bindings/perf/fsl-imx-ddr.txt @@ -0,0 +1,21 @@ +* Freescale(NXP) IMX8 DDR performance monitor + +Required properties: + +- compatible: should be one of: + "fsl,imx8-ddr-pmu" + "fsl,imx8m-ddr-pmu" + +- reg: physical address and size + +- interrupts: single interrupt + generated by the control block + +Example: + + ddr-pmu@5c020000 { + compatible = "fsl,imx8-ddr-pmu"; + reg = <0x5c020000 0x10000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt index 7d9d3f90641b..493bec80d59b 100644 --- a/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt +++ b/Documentation/devicetree/bindings/pwm/ingenic,jz47xx-pwm.txt @@ -2,10 +2,7 @@ Ingenic JZ47xx PWM Controller ============================= Required properties: -- compatible: One of: - * "ingenic,jz4740-pwm" - * "ingenic,jz4770-pwm" - * "ingenic,jz4780-pwm" +- compatible: Should be "ingenic,jz4740-pwm" - #pwm-cells: Should be 3. See pwm.txt in this directory for a description of the cells format. - clocks : phandle to the external clock. diff --git a/Documentation/devicetree/bindings/pwm/pwm-sifive.txt b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt new file mode 100644 index 000000000000..36447e3c9378 --- /dev/null +++ b/Documentation/devicetree/bindings/pwm/pwm-sifive.txt @@ -0,0 +1,33 @@ +SiFive PWM controller + +Unlike most other PWM controllers, the SiFive PWM controller currently only +supports one period for all channels in the PWM. All PWMs need to run at +the same period. The period also has significant restrictions on the values +it can achieve, which the driver rounds to the nearest achievable period. +PWM RTL that corresponds to the IP block version numbers can be found +here: + +https://github.com/sifive/sifive-blocks/tree/master/src/main/scala/devices/pwm + +Required properties: +- compatible: Should be "sifive,<chip>-pwm" and "sifive,pwm<version>". + Supported compatible strings are: "sifive,fu540-c000-pwm" for the SiFive + PWM v0 as integrated onto the SiFive FU540 chip, and "sifive,pwm0" for the + SiFive PWM v0 IP block with no chip integration tweaks. + Please refer to sifive-blocks-ip-versioning.txt for details. +- reg: physical base address and length of the controller's registers +- clocks: Should contain a clock identifier for the PWM's parent clock. +- #pwm-cells: Should be 3. See pwm.txt in this directory + for a description of the cell format. +- interrupts: one interrupt per PWM channel + +Examples: + +pwm: pwm@10020000 { + compatible = "sifive,fu540-c000-pwm", "sifive,pwm0"; + reg = <0x0 0x10020000 0x0 0x1000>; + clocks = <&tlclk>; + interrupt-parent = <&plic>; + interrupts = <42 43 44 45>; + #pwm-cells = <3>; +}; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt index bd23302e84be..6521bc44a74e 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32-lp.txt @@ -11,8 +11,10 @@ Required parameters: bindings defined in pwm.txt. Optional properties: -- pinctrl-names: Set to "default". -- pinctrl-0: Phandle pointing to pin configuration node for PWM. +- pinctrl-names: Set to "default". An additional "sleep" state can be + defined to set pins in sleep state when in low power. +- pinctrl-n: Phandle(s) pointing to pin configuration node for PWM, + respectively for "default" and "sleep" states. Example: timer@40002400 { @@ -21,7 +23,8 @@ Example: pwm { compatible = "st,stm32-pwm-lp"; #pwm-cells = <3>; - pinctrl-names = "default"; + pinctrl-names = "default", "sleep"; pinctrl-0 = <&lppwm1_pins>; + pinctrl-1 = <&lppwm1_sleep_pins>; }; }; diff --git a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt index 3e6d55018d7a..a8690bfa5e1f 100644 --- a/Documentation/devicetree/bindings/pwm/pwm-stm32.txt +++ b/Documentation/devicetree/bindings/pwm/pwm-stm32.txt @@ -8,6 +8,8 @@ Required parameters: - pinctrl-names: Set to "default". - pinctrl-0: List of phandles pointing to pin configuration nodes for PWM module. For Pinctrl properties see ../pinctrl/pinctrl-bindings.txt +- #pwm-cells: Should be set to 3. This PWM chip uses the default 3 cells + bindings defined in pwm.txt. Optional parameters: - st,breakinput: One or two <index level filter> to describe break input configurations. @@ -28,6 +30,7 @@ Example: pwm { compatible = "st,stm32-pwm"; + #pwm-cells = <3>; pinctrl-0 = <&pwm1_pins>; pinctrl-names = "default"; st,breakinput = <0 1 5>; diff --git a/Documentation/devicetree/bindings/riscv/cpus.yaml b/Documentation/devicetree/bindings/riscv/cpus.yaml new file mode 100644 index 000000000000..f97a4ecd7b91 --- /dev/null +++ b/Documentation/devicetree/bindings/riscv/cpus.yaml @@ -0,0 +1,170 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/riscv/cpus.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: RISC-V bindings for 'cpus' DT nodes + +maintainers: + - Paul Walmsley <paul.walmsley@sifive.com> + - Palmer Dabbelt <palmer@sifive.com> + +allOf: + - $ref: /schemas/cpus.yaml# + +properties: + $nodename: + const: cpus + description: Container of cpu nodes + + '#address-cells': + const: 1 + description: | + A single unsigned 32-bit integer uniquely identifies each RISC-V + hart in a system. (See the "reg" node under the "cpu" node, + below). + + '#size-cells': + const: 0 + +patternProperties: + '^cpu@[0-9a-f]+$': + properties: + compatible: + type: array + items: + - enum: + - sifive,rocket0 + - sifive,e5 + - sifive,e51 + - sifive,u54-mc + - sifive,u54 + - sifive,u5 + - const: riscv + description: + Identifies that the hart uses the RISC-V instruction set + and identifies the type of the hart. + + mmu-type: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - riscv,sv32 + - riscv,sv39 + - riscv,sv48 + description: + Identifies the MMU address translation mode used on this + hart. These values originate from the RISC-V Privileged + Specification document, available from + https://riscv.org/specifications/ + + riscv,isa: + allOf: + - $ref: "/schemas/types.yaml#/definitions/string" + - enum: + - rv64imac + - rv64imafdc + description: + Identifies the specific RISC-V instruction set architecture + supported by the hart. These are documented in the RISC-V + User-Level ISA document, available from + https://riscv.org/specifications/ + + timebase-frequency: + type: integer + minimum: 1 + description: + Specifies the clock frequency of the system timer in Hz. + This value is common to all harts on a single system image. + + interrupt-controller: + type: object + description: Describes the CPU's local interrupt controller + + properties: + '#interrupt-cells': + const: 1 + + compatible: + const: riscv,cpu-intc + + interrupt-controller: true + + required: + - '#interrupt-cells' + - compatible + - interrupt-controller + + required: + - riscv,isa + - timebase-frequency + - interrupt-controller + +examples: + - | + // Example 1: SiFive Freedom U540G Development Kit + cpus { + #address-cells = <1>; + #size-cells = <0>; + timebase-frequency = <1000000>; + cpu@0 { + clock-frequency = <0>; + compatible = "sifive,rocket0", "riscv"; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <128>; + i-cache-size = <16384>; + reg = <0>; + riscv,isa = "rv64imac"; + cpu_intc0: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + cpu@1 { + clock-frequency = <0>; + compatible = "sifive,rocket0", "riscv"; + d-cache-block-size = <64>; + d-cache-sets = <64>; + d-cache-size = <32768>; + d-tlb-sets = <1>; + d-tlb-size = <32>; + device_type = "cpu"; + i-cache-block-size = <64>; + i-cache-sets = <64>; + i-cache-size = <32768>; + i-tlb-sets = <1>; + i-tlb-size = <32>; + mmu-type = "riscv,sv39"; + reg = <1>; + riscv,isa = "rv64imafdc"; + tlb-split; + cpu_intc1: interrupt-controller { + #interrupt-cells = <1>; + compatible = "riscv,cpu-intc"; + interrupt-controller; + }; + }; + }; + + - | + // Example 2: Spike ISA Simulator with 1 Hart + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + reg = <0>; + compatible = "riscv"; + riscv,isa = "rv64imafdc"; + mmu-type = "riscv,sv48"; + interrupt-controller { + #interrupt-cells = <1>; + interrupt-controller; + compatible = "riscv,cpu-intc"; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/riscv/sifive.yaml b/Documentation/devicetree/bindings/riscv/sifive.yaml new file mode 100644 index 000000000000..9d17dc2f3f84 --- /dev/null +++ b/Documentation/devicetree/bindings/riscv/sifive.yaml @@ -0,0 +1,25 @@ +# SPDX-License-Identifier: (GPL-2.0 OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/riscv/sifive.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SiFive SoC-based boards + +maintainers: + - Paul Walmsley <paul.walmsley@sifive.com> + - Palmer Dabbelt <palmer@sifive.com> + +description: + SiFive SoC-based boards + +properties: + $nodename: + const: '/' + compatible: + items: + - enum: + - sifive,freedom-unleashed-a00 + - const: sifive,fu540-c000 + - const: sifive,fu540 +... diff --git a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt index 0014da9145af..c223e54452da 100644 --- a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt +++ b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.txt @@ -2,6 +2,7 @@ HWRNG support for the iproc-rng200 driver Required properties: - compatible : Must be one of: + "brcm,bcm7211-rng200" "brcm,bcm7278-rng200" "brcm,iproc-rng200" - reg : base address and size of control register block diff --git a/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt new file mode 100644 index 000000000000..d57659996d62 --- /dev/null +++ b/Documentation/devicetree/bindings/timer/nxp,sysctr-timer.txt @@ -0,0 +1,25 @@ +NXP System Counter Module(sys_ctr) + +The system counter(sys_ctr) is a programmable system counter which provides +a shared time base to Cortex A15, A7, A53, A73, etc. it is intended for use in +applications where the counter is always powered and support multiple, +unrelated clocks. The compare frame inside can be used for timer purpose. + +Required properties: + +- compatible : should be "nxp,sysctr-timer" +- reg : Specifies the base physical address and size of the comapre + frame and the counter control, read & compare. +- interrupts : should be the first compare frames' interrupt +- clocks : Specifies the counter clock. +- clock-names: Specifies the clock's name of this module + +Example: + + system_counter: timer@306a0000 { + compatible = "nxp,sysctr-timer"; + reg = <0x306a0000 0x20000>;/* system-counter-rd & compare */ + clocks = <&clk_8m>; + clock-names = "per"; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/trivial-devices.yaml b/Documentation/devicetree/bindings/trivial-devices.yaml index 747fd3f689dc..2e742d399e87 100644 --- a/Documentation/devicetree/bindings/trivial-devices.yaml +++ b/Documentation/devicetree/bindings/trivial-devices.yaml @@ -52,6 +52,10 @@ properties: - at,24c08 # i2c trusted platform module (TPM) - atmel,at97sc3204t + # i2c h/w symmetric crypto module + - atmel,atsha204a + # i2c h/w elliptic curve crypto module + - atmel,atecc508a # CM32181: Ambient Light Sensor - capella,cm32181 # CM3232: Ambient Light Sensor |