summaryrefslogtreecommitdiff
path: root/Documentation
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation')
-rw-r--r--Documentation/devicetree/bindings/watchdog/atmel-wdt.txt30
-rw-r--r--Documentation/devicetree/bindings/watchdog/davinci-wdt.txt16
-rw-r--r--Documentation/devicetree/bindings/watchdog/gpio-wdt.txt23
-rw-r--r--Documentation/devicetree/bindings/watchdog/samsung-wdt.txt21
4 files changed, 85 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
index fcdd48f7dcff..f90e294d7631 100644
--- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt
@@ -9,11 +9,37 @@ Required properties:
Optional properties:
- timeout-sec: contains the watchdog timeout in seconds.
+- interrupts : Should contain WDT interrupt.
+- atmel,max-heartbeat-sec : Should contain the maximum heartbeat value in
+ seconds. This value should be less or equal to 16. It is used to
+ compute the WDV field.
+- atmel,min-heartbeat-sec : Should contain the minimum heartbeat value in
+ seconds. This value must be smaller than the max-heartbeat-sec value.
+ It is used to compute the WDD field.
+- atmel,watchdog-type : Should be "hardware" or "software". Hardware watchdog
+ use the at91 watchdog reset. Software watchdog use the watchdog
+ interrupt to trigger a software reset.
+- atmel,reset-type : Should be "proc" or "all".
+ "all" : assert peripherals and processor reset signals
+ "proc" : assert the processor reset signal
+ This is valid only when using "hardware" watchdog.
+- atmel,disable : Should be present if you want to disable the watchdog.
+- atmel,idle-halt : Should be present if you want to stop the watchdog when
+ entering idle state.
+- atmel,dbg-halt : Should be present if you want to stop the watchdog when
+ entering debug state.
Example:
-
watchdog@fffffd40 {
compatible = "atmel,at91sam9260-wdt";
reg = <0xfffffd40 0x10>;
- timeout-sec = <10>;
+ interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+ timeout-sec = <15>;
+ atmel,watchdog-type = "hardware";
+ atmel,reset-type = "all";
+ atmel,dbg-halt;
+ atmel,idle-halt;
+ atmel,max-heartbeat-sec = <16>;
+ atmel,min-heartbeat-sec = <0>;
+ status = "okay";
};
diff --git a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt
index 75558ccd9a05..e60b9a13bdcb 100644
--- a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt
@@ -1,12 +1,24 @@
-DaVinci Watchdog Timer (WDT) Controller
+Texas Instruments DaVinci/Keystone Watchdog Timer (WDT) Controller
Required properties:
-- compatible : Should be "ti,davinci-wdt"
+- compatible : Should be "ti,davinci-wdt", "ti,keystone-wdt"
- reg : Should contain WDT registers location and length
+Optional properties:
+- timeout-sec : Contains the watchdog timeout in seconds
+- clocks : the clock feeding the watchdog timer.
+ Needed if platform uses clocks.
+ See clock-bindings.txt
+
+Documentation:
+Davinci DM646x - http://www.ti.com/lit/ug/spruer5b/spruer5b.pdf
+Keystone - http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf
+
Examples:
wdt: wdt@2320000 {
compatible = "ti,davinci-wdt";
reg = <0x02320000 0x80>;
+ timeout-sec = <30>;
+ clocks = <&clkwdtimer0>;
};
diff --git a/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
new file mode 100644
index 000000000000..37afec194949
--- /dev/null
+++ b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt
@@ -0,0 +1,23 @@
+* GPIO-controlled Watchdog
+
+Required Properties:
+- compatible: Should contain "linux,wdt-gpio".
+- gpios: From common gpio binding; gpio connection to WDT reset pin.
+- hw_algo: The algorithm used by the driver. Should be one of the
+ following values:
+ - toggle: Either a high-to-low or a low-to-high transition clears
+ the WDT counter. The watchdog timer is disabled when GPIO is
+ left floating or connected to a three-state buffer.
+ - level: Low or high level starts counting WDT timeout,
+ the opposite level disables the WDT. Active level is determined
+ by the GPIO flags.
+- hw_margin_ms: Maximum time to reset watchdog circuit (milliseconds).
+
+Example:
+ watchdog: watchdog {
+ /* ADM706 */
+ compatible = "linux,wdt-gpio";
+ gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ hw_margin_ms = <1600>;
+ };
diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
index 2aa486cc1ff6..cfff37511aac 100644
--- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt
@@ -5,10 +5,29 @@ after a preset amount of time during which the WDT reset event has not
occurred.
Required properties:
-- compatible : should be "samsung,s3c2410-wdt"
+- compatible : should be one among the following
+ (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs
+ (b) "samsung,exynos5250-wdt" for Exynos5250
+ (c) "samsung,exynos5420-wdt" for Exynos5420
+
- reg : base physical address of the controller and length of memory mapped
region.
- interrupts : interrupt number to the cpu.
+- samsung,syscon-phandle : reference to syscon node (This property required only
+ in case of compatible being "samsung,exynos5250-wdt" or "samsung,exynos5420-wdt".
+ In case of Exynos5250 and 5420 this property points to syscon node holding the PMU
+ base address)
Optional properties:
- timeout-sec : contains the watchdog timeout in seconds.
+
+Example:
+
+watchdog@101D0000 {
+ compatible = "samsung,exynos5250-wdt";
+ reg = <0x101D0000 0x100>;
+ interrupts = <0 42 0>;
+ clocks = <&clock 336>;
+ clock-names = "watchdog";
+ samsung,syscon-phandle = <&pmu_syscon>;
+};