diff options
Diffstat (limited to 'Documentation')
36 files changed, 1556 insertions, 587 deletions
diff --git a/Documentation/ABI/testing/sysfs-class-power-mp2629 b/Documentation/ABI/testing/sysfs-class-power-mp2629 new file mode 100644 index 000000000000..327a07e22805 --- /dev/null +++ b/Documentation/ABI/testing/sysfs-class-power-mp2629 @@ -0,0 +1,8 @@ +What: /sys/class/power_supply/mp2629_battery/batt_impedance_compen +Date: April 2020 +KernelVersion: 5.7 +Description: + Represents a battery impedance compensation to accelerate charging. + + Access: Read, Write + Valid values: Represented in milli-ohms. Valid range is [0, 140]. diff --git a/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml b/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml index a5dc070d0ca7..3bbe9521c0bc 100644 --- a/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml +++ b/Documentation/devicetree/bindings/dsp/fsl,dsp.yaml @@ -17,6 +17,8 @@ properties: compatible: enum: - fsl,imx8qxp-dsp + - fsl,imx8qm-dsp + - fsl,imx8mp-dsp reg: description: Should contain register location and length diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt deleted file mode 100644 index c06863badfbd..000000000000 --- a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.txt +++ /dev/null @@ -1,154 +0,0 @@ -Binding for Qualcomm Technologies, Inc. WLED driver - -WLED (White Light Emitting Diode) driver is used for controlling display -backlight that is part of PMIC on Qualcomm Technologies, Inc. reference -platforms. The PMIC is connected to the host processor via SPMI bus. - -- compatible - Usage: required - Value type: <string> - Definition: should be one of: - "qcom,pm8941-wled" - "qcom,pmi8998-wled" - "qcom,pm660l-wled" - -- reg - Usage: required - Value type: <prop encoded array> - Definition: Base address of the WLED modules. - -- default-brightness - Usage: optional - Value type: <u32> - Definition: brightness value on boot, value from: 0-4095. - Default: 2048 - -- label - Usage: required - Value type: <string> - Definition: The name of the backlight device - -- qcom,cs-out - Usage: optional - Value type: <bool> - Definition: enable current sink output. - This property is supported only for PM8941. - -- qcom,cabc - Usage: optional - Value type: <bool> - Definition: enable content adaptive backlight control. - -- qcom,ext-gen - Usage: optional - Value type: <bool> - Definition: use externally generated modulator signal to dim. - This property is supported only for PM8941. - -- qcom,current-limit - Usage: optional - Value type: <u32> - Definition: mA; per-string current limit; value from 0 to 25 with - 1 mA step. Default 20 mA. - This property is supported only for pm8941. - -- qcom,current-limit-microamp - Usage: optional - Value type: <u32> - Definition: uA; per-string current limit; value from 0 to 30000 with - 2500 uA step. Default 25 mA. - -- qcom,current-boost-limit - Usage: optional - Value type: <u32> - Definition: mA; boost current limit. - For pm8941: one of: 105, 385, 525, 805, 980, 1260, 1400, - 1680. Default: 805 mA. - For pmi8998: one of: 105, 280, 450, 620, 970, 1150, 1300, - 1500. Default: 970 mA. - -- qcom,switching-freq - Usage: optional - Value type: <u32> - Definition: kHz; switching frequency; one of: 600, 640, 685, 738, - 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, - 4800, 9600. - Default: for pm8941: 1600 kHz - for pmi8998: 800 kHz - -- qcom,ovp - Usage: optional - Value type: <u32> - Definition: V; Over-voltage protection limit; one of: - 27, 29, 32, 35. Default: 29V - This property is supported only for PM8941. - -- qcom,ovp-millivolt - Usage: optional - Value type: <u32> - Definition: mV; Over-voltage protection limit; - For pmi8998: one of 18100, 19600, 29600, 31100. - Default 29600 mV. - If this property is not specified for PM8941, it - falls back to "qcom,ovp" property. - -- qcom,num-strings - Usage: optional - Value type: <u32> - Definition: #; number of led strings attached; - value: For PM8941 from 1 to 3. Default: 2 - For PMI8998 from 1 to 4. - -- interrupts - Usage: optional - Value type: <prop encoded array> - Definition: Interrupts associated with WLED. This should be - "short" and "ovp" interrupts. Interrupts can be - specified as per the encoding listed under - Documentation/devicetree/bindings/spmi/ - qcom,spmi-pmic-arb.txt. - -- interrupt-names - Usage: optional - Value type: <string> - Definition: Interrupt names associated with the interrupts. - Must be "short" and "ovp". The short circuit detection - is not supported for PM8941. - -- qcom,enabled-strings - Usage: optional - Value tyoe: <u32 array> - Definition: Array of the WLED strings numbered from 0 to 3. Each - string of leds are operated individually. Specify the - list of strings used by the device. Any combination of - led strings can be used. - -- qcom,external-pfet - Usage: optional - Value type: <bool> - Definition: Specify if external PFET control for short circuit - protection is used. This property is supported only - for PMI8998. - -- qcom,auto-string-detection - Usage: optional - Value type: <bool> - Definition: Enables auto-detection of the WLED string configuration. - This feature is not supported for PM8941. - - -Example: - -pm8941-wled@d800 { - compatible = "qcom,pm8941-wled"; - reg = <0xd800>; - label = "backlight"; - - qcom,cs-out; - qcom,current-limit = <20>; - qcom,current-boost-limit = <805>; - qcom,switching-freq = <1600>; - qcom,ovp = <29>; - qcom,num-strings = <2>; - qcom,enabled-strings = <0 1>; -}; diff --git a/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml new file mode 100644 index 000000000000..01c7d93dc658 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/backlight/qcom-wled.yaml @@ -0,0 +1,261 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/backlight/qcom-wled.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Binding for Qualcomm Technologies, Inc. WLED driver + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + - Kiran Gunda <kgunda@codeaurora.org> + +description: | + WLED (White Light Emitting Diode) driver is used for controlling display + backlight that is part of PMIC on Qualcomm Technologies, Inc. reference + platforms. The PMIC is connected to the host processor via SPMI bus. + +properties: + compatible: + enum: + - qcom,pm8941-wled + - qcom,pmi8998-wled + - qcom,pm660l-wled + - qcom,pm8150l-wled + + reg: + maxItems: 1 + + default-brightness: + description: | + brightness value on boot. + + label: true + + max-brightness: + description: | + Maximum brightness level. + + qcom,cs-out: + description: | + enable current sink output. + This property is supported only for WLED3. + type: boolean + + qcom,cabc: + description: | + enable content adaptive backlight control. + type: boolean + + qcom,ext-gen: + description: | + use externally generated modulator signal to dim. + This property is supported only for WLED3. + type: boolean + + qcom,current-limit: + description: | + mA; per-string current limit. + This property is supported only for WLED3. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + default: 20 + minimum: 0 + maximum: 25 + + qcom,current-limit-microamp: + description: | + uA; per-string current limit. + default: 25 + minimum: 0 + maximum: 30000 + multipleOf: 25 + + qcom,current-boost-limit: + description: | + mA; boost current limit. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + + qcom,switching-freq: + description: | + kHz; switching frequency. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 600, 640, 685, 738, 800, 872, 960, 1066, 1200, 1371, 1600, 1920, 2400, 3200, 4800, 9600 ] + + qcom,ovp: + description: | + V; Over-voltage protection limit. + This property is supported only for WLED3. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 27, 29, 32, 35 ] + - default: 29 + + qcom,ovp-millivolt: + description: | + Over-voltage protection limit. This property is for WLED4 only. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 18100, 19600, 29600, 31100 ] + - default: 29600 + + qcom,num-strings: + description: | + number of led strings attached. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + + qcom,enabled-strings: + description: | + Array of the WLED strings numbered from 0 to 3. Each + string of leds are operated individually. Specify the + list of strings used by the device. Any combination of + led strings can be used. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 1 + maxItems: 4 + + qcom,external-pfet: + description: | + Specify if external PFET control for short circuit + protection is used. This property is supported only + for WLED4. + type: boolean + + qcom,auto-string-detection: + description: | + Enables auto-detection of the WLED string configuration. + This feature is not supported for WLED3. + type: boolean + + interrupts: + minItems: 1 + items: + - description: over voltage protection interrupt. + - description: short circuit interrupt. + + interrupt-names: + minItems: 1 + items: + - const: ovp + - const: short + + qcom,modulator-sel: + description: | + Selects the modulator used for brightness modulation. + Allowed values are, + 0 - Modulator A + 1 - Modulator B + This property is applicable only to WLED5 peripheral. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1 ] + - default: 0 + + qcom,cabc-sel: + description: | + Selects the CABC pin signal used for brightness modulation. + Allowed values are, + 0 - CABC disabled + 1 - CABC 1 + 2 - CABC 2 + 3 - External signal (e.g. LPG) is used for dimming + This property is applicable only to WLED5 peripheral. + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [ 0, 1, 2, 3 ] + +allOf: + - if: + properties: + compatible: + contains: + const: qcom,pm8941-wled + + then: + properties: + qcom,current-boost-limit: + enum: [ 105, 385, 525, 805, 980, 1260, 1400, 1680 ] + default: 805 + + qcom,switching-freq: + default: 1600 + + qcom,num-strings: + enum: [ 1, 2, 3 ] + + interrupts: + maxItems: 1 + + interrupt-names: + maxItems: 1 + + else: + properties: + qcom,current-boost-limit: + enum: [ 105, 280, 450, 620, 970, 1150, 1300, 1500 ] + default: 970 + + qcom,switching-freq: + default: 800 + + qcom,num-strings: + enum: [ 1, 2, 3, 4 ] + + interrupts: + minItems: 2 + + interrupt-names: + minItems: 2 + - if: + properties: + compatible: + contains: + enum: + - qcom,pm8150l-wled + + then: + properties: + default-brightness: + minimum: 0 + maximum: 32767 + + max-brightness: + minimum: 0 + maximum: 32767 + + else: + properties: + default-brightness: + minimum: 0 + maximum: 4095 + + max-brightness: + minimum: 0 + maximum: 4095 + +required: + - compatible + - reg + - label + +additionalProperties: false + +examples: + - | + backlight@d800 { + compatible = "qcom,pm8941-wled"; + reg = <0xd800 0x100>; + label = "backlight"; + + qcom,cs-out; + qcom,current-limit = <20>; + qcom,current-boost-limit = <805>; + qcom,switching-freq = <1600>; + qcom,ovp = <29>; + qcom,num-strings = <2>; + qcom,enabled-strings = <0 1>; + }; diff --git a/Documentation/devicetree/bindings/leds/leds-aw2013.yaml b/Documentation/devicetree/bindings/leds/leds-aw2013.yaml new file mode 100644 index 000000000000..f118721df1e8 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-aw2013.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/leds-aw2013.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: AWINIC AW2013 3-channel LED Driver + +maintainers: + - Nikita Travkin <nikitos.tr@gmail.com> + +description: | + The AW2013 is a 3-channel LED driver with I2C interface. It can control + LED brightness with PWM output. + +properties: + compatible: + const: awinic,aw2013 + + reg: + maxItems: 1 + + vcc-supply: + description: Regulator providing power to the "VCC" pin. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^led@[0-2]$": + type: object + allOf: + - $ref: common.yaml# + + properties: + reg: + description: Index of the LED. + minimum: 0 + maximum: 2 + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + i2c0 { + #address-cells = <1>; + #size-cells = <0>; + + led-controller@45 { + compatible = "awinic,aw2013"; + reg = <0x45>; + #address-cells = <1>; + #size-cells = <0>; + + vcc-supply = <&pm8916_l17>; + + led@0 { + reg = <0>; + led-max-microamp = <5000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_RED>; + }; + + led@1 { + reg = <1>; + led-max-microamp = <5000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_GREEN>; + }; + + led@2 { + reg = <2>; + led-max-microamp = <5000>; + function = LED_FUNCTION_INDICATOR; + color = <LED_COLOR_ID_BLUE>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml b/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml new file mode 100644 index 000000000000..ecf7ac9ab067 --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-sgm3140.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/leds/leds-sgm3140.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SGMICRO SGM3140 500mA Buck/Boost Charge Pump LED Driver + +maintainers: + - Luca Weiss <luca@z3ntu.xyz> + +description: | + The SGM3140 is a current-regulated charge pump which can regulate two current + levels for Flash and Torch modes. + + The data sheet can be found at: + http://www.sg-micro.com/uploads/soft/20190626/1561535688.pdf + +properties: + compatible: + const: sgmicro,sgm3140 + + enable-gpios: + maxItems: 1 + description: A connection to the 'EN' pin. + + flash-gpios: + maxItems: 1 + description: A connection to the 'FLASH' pin. + + vin-supply: + description: Regulator providing power to the 'VIN' pin. + + led: + type: object + allOf: + - $ref: common.yaml# + +required: + - compatible + - flash-gpios + - enable-gpios + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/leds/common.h> + + led-controller { + compatible = "sgmicro,sgm3140"; + flash-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ + enable-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */ + vin-supply = <®_dcdc1>; + + sgm3140_flash: led { + function = LED_FUNCTION_FLASH; + color = <LED_COLOR_ID_WHITE>; + flash-max-timeout-us = <250000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/mps,mp2629.yaml b/Documentation/devicetree/bindings/mfd/mps,mp2629.yaml new file mode 100644 index 000000000000..f91acc42d652 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mps,mp2629.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/mps,mp2629.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MP2629 Battery Charger PMIC from Monolithic Power System. + +maintainers: + - Saravanan Sekar <sravanhome@gmail.com> + +description: | + MP2629 is a PMIC providing battery charging and power supply for smartphones, + wireless camera and portable devices. Chip is controlled over I2C. + + The battery charge management device handles battery charger controller and + ADC IIO device for battery, system voltage + +properties: + compatible: + const: mps,mp2629 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + interrupt-controller: true + + "#interrupt-cells": + const: 2 + description: + The first cell is the IRQ number, the second cell is the trigger type. + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - "#interrupt-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/input/linux-event-codes.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + pmic@4b { + compatible = "mps,mp2629"; + reg = <0x4b>; + + interrupt-controller; + interrupt-parent = <&gpio2>; + #interrupt-cells = <2>; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/mt6397.txt b/Documentation/devicetree/bindings/mfd/mt6397.txt index a9b105ac00a8..2661775a3825 100644 --- a/Documentation/devicetree/bindings/mfd/mt6397.txt +++ b/Documentation/devicetree/bindings/mfd/mt6397.txt @@ -18,24 +18,30 @@ See the following for pwarp node definitions: This document describes the binding for MFD device and its sub module. Required properties: -compatible: "mediatek,mt6397" or "mediatek,mt6323" +compatible: + "mediatek,mt6323" for PMIC MT6323 + "mediatek,mt6358" for PMIC MT6358 + "mediatek,mt6397" for PMIC MT6397 Optional subnodes: - rtc Required properties: Should be one of follows - compatible: "mediatek,mt6323-rtc" + - compatible: "mediatek,mt6358-rtc" - compatible: "mediatek,mt6397-rtc" For details, see ../rtc/rtc-mt6397.txt - regulators Required properties: - - compatible: "mediatek,mt6397-regulator" - see ../regulator/mt6397-regulator.txt - compatible: "mediatek,mt6323-regulator" see ../regulator/mt6323-regulator.txt + - compatible: "mediatek,mt6358-regulator" + see ../regulator/mt6358-regulator.txt + - compatible: "mediatek,mt6397-regulator" + see ../regulator/mt6397-regulator.txt - codec Required properties: - - compatible: "mediatek,mt6397-codec" + - compatible: "mediatek,mt6397-codec" or "mediatek,mt6358-sound" - clk Required properties: - compatible: "mediatek,mt6397-clk" @@ -54,6 +60,11 @@ Optional subnodes: - compatible: "mediatek,mt6323-pwrc" For details, see ../power/reset/mt6323-poweroff.txt +- pin-controller + Required properties: + - compatible: "mediatek,mt6397-pinctrl" + For details, see ../pinctrl/pinctrl-mt65xx.txt + Example: pwrap: pwrap@1000f000 { compatible = "mediatek,mt8135-pwrap"; diff --git a/Documentation/devicetree/bindings/sound/da7213.txt b/Documentation/devicetree/bindings/sound/da7213.txt index 58902802d56c..94584c96c4ae 100644 --- a/Documentation/devicetree/bindings/sound/da7213.txt +++ b/Documentation/devicetree/bindings/sound/da7213.txt @@ -1,9 +1,9 @@ -Dialog Semiconductor DA7213 Audio Codec bindings +Dialog Semiconductor DA7212/DA7213 Audio Codec bindings ====== Required properties: -- compatible : Should be "dlg,da7213" +- compatible : Should be "dlg,da7212" or "dlg,da7213" - reg: Specifies the I2C slave address Optional properties: @@ -21,6 +21,10 @@ Optional properties: - dlg,dmic-clkrate : DMIC clock frequency (Hz). [<1500000>, <3000000>] + - VDDA-supply : Regulator phandle for Analogue power supply + - VDDMIC-supply : Regulator phandle for Mic Bias + - VDDIO-supply : Regulator phandle for I/O power supply + ====== Example: diff --git a/Documentation/devicetree/bindings/sound/fsl,asrc.txt b/Documentation/devicetree/bindings/sound/fsl,asrc.txt index cb9a25165503..998b4c8a7f78 100644 --- a/Documentation/devicetree/bindings/sound/fsl,asrc.txt +++ b/Documentation/devicetree/bindings/sound/fsl,asrc.txt @@ -51,6 +51,10 @@ Optional properties: will be in use as default. Otherwise, the big endian mode will be in use for all the device registers. + - fsl,asrc-format : Defines a mutual sample format used by DPCM Back + Ends, which can replace the fsl,asrc-width. + The value is 2 (S16_LE), or 6 (S24_LE). + Example: asrc: asrc@2034000 { diff --git a/Documentation/devicetree/bindings/sound/fsl,easrc.yaml b/Documentation/devicetree/bindings/sound/fsl,easrc.yaml new file mode 100644 index 000000000000..73cdcf053a9c --- /dev/null +++ b/Documentation/devicetree/bindings/sound/fsl,easrc.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/fsl,easrc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP Asynchronous Sample Rate Converter (ASRC) Controller + +maintainers: + - Shengjiu Wang <shengjiu.wang@nxp.com> + +properties: + $nodename: + pattern: "^easrc@.*" + + compatible: + const: fsl,imx8mn-easrc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Peripheral clock + + clock-names: + items: + - const: mem + + dmas: + maxItems: 8 + + dma-names: + items: + - const: ctx0_rx + - const: ctx0_tx + - const: ctx1_rx + - const: ctx1_tx + - const: ctx2_rx + - const: ctx2_tx + - const: ctx3_rx + - const: ctx3_tx + + firmware-name: + allOf: + - $ref: /schemas/types.yaml#/definitions/string + - const: imx/easrc/easrc-imx8mn.bin + description: The coefficient table for the filters + + fsl,asrc-rate: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - minimum: 8000 + - maximum: 192000 + description: Defines a mutual sample rate used by DPCM Back Ends + + fsl,asrc-format: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + - enum: [2, 6, 10, 32, 36] + default: 2 + description: + Defines a mutual sample format used by DPCM Back Ends + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + - dmas + - dma-names + - firmware-name + - fsl,asrc-rate + - fsl,asrc-format + +examples: + - | + #include <dt-bindings/clock/imx8mn-clock.h> + + easrc: easrc@300c0000 { + compatible = "fsl,imx8mn-easrc"; + reg = <0x0 0x300c0000 0x0 0x10000>; + interrupts = <0x0 122 0x4>; + clocks = <&clk IMX8MN_CLK_ASRC_ROOT>; + clock-names = "mem"; + dmas = <&sdma2 16 23 0> , <&sdma2 17 23 0>, + <&sdma2 18 23 0> , <&sdma2 19 23 0>, + <&sdma2 20 23 0> , <&sdma2 21 23 0>, + <&sdma2 22 23 0> , <&sdma2 23 23 0>; + dma-names = "ctx0_rx", "ctx0_tx", + "ctx1_rx", "ctx1_tx", + "ctx2_rx", "ctx2_tx", + "ctx3_rx", "ctx3_tx"; + firmware-name = "imx/easrc/easrc-imx8mn.bin"; + fsl,asrc-rate = <8000>; + fsl,asrc-format = <2>; + }; diff --git a/Documentation/devicetree/bindings/sound/fsl,esai.txt b/Documentation/devicetree/bindings/sound/fsl,esai.txt index 0e6e2166f76c..0a2480aeecf0 100644 --- a/Documentation/devicetree/bindings/sound/fsl,esai.txt +++ b/Documentation/devicetree/bindings/sound/fsl,esai.txt @@ -12,6 +12,7 @@ Required properties: "fsl,imx35-esai", "fsl,vf610-esai", "fsl,imx6ull-esai", + "fsl,imx8qm-esai", - reg : Offset and length of the register set for the device. diff --git a/Documentation/devicetree/bindings/sound/marvell,mmp-sspa.yaml b/Documentation/devicetree/bindings/sound/marvell,mmp-sspa.yaml new file mode 100644 index 000000000000..6d20a24a2ae9 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/marvell,mmp-sspa.yaml @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/marvell,mmp-sspa.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvel SSPA Digital Audio Interface Bindings + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + $nodename: + pattern: "^audio-controller(@.*)?$" + + compatible: + const: marvell,mmp-sspa + + reg: + items: + - description: RX block + - description: TX block + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Clock for the Audio block + - description: I2S bit clock + + clock-names: + items: + - const: audio + - const: bitclk + + power-domains: + maxItems: 1 + + '#sound-dai-cells': + const: 0 + + dmas: + items: + - description: TX DMA Channel + - description: RX DMA Channel + + dma-names: + items: + - const: tx + - const: rx + + port: + type: object + + properties: + endpoint: + type: object + + properties: + remote-endpoint: true + + frame-master: + type: boolean + description: SoC generates the frame clock + + bitclock-master: + type: boolean + description: SoC generates the bit clock + + dai-format: + $ref: /schemas/types.yaml#/definitions/string + description: The digital audio format + const: i2s + + required: + - remote-endpoint + + required: + - endpoint + + additionalProperties: false + +required: + - "#sound-dai-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + - dmas + - dma-names + - port + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/marvell,mmp2.h> + + audio-controller@d42a0c00 { + compatible = "marvell,mmp-sspa"; + reg = <0xd42a0c00 0x30>, + <0xd42a0c80 0x30>; + interrupts = <2>; + clock-names = "audio", "bitclk"; + clocks = <&soc_clocks 127>, + <&audio_clk 1>; + #sound-dai-cells = <0>; + dmas = <&adma0 0>, <&adma0 1>; + dma-names = "tx", "rx"; + port { + endpoint { + remote-endpoint = <&rt5631_0>; + frame-master; + bitclock-master; + dai-format = "i2s"; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/sound/nau8810.txt b/Documentation/devicetree/bindings/sound/nau8810.txt index 05830e477acd..7deaa452b200 100644 --- a/Documentation/devicetree/bindings/sound/nau8810.txt +++ b/Documentation/devicetree/bindings/sound/nau8810.txt @@ -1,10 +1,11 @@ -NAU8810 audio CODEC +NAU8810/NAU8812/NAU8814 audio CODEC This device supports I2C only. Required properties: - - compatible : "nuvoton,nau8810" + - compatible : One of "nuvoton,nau8810" or "nuvoton,nau8812" or + "nuvoton,nau8814" - reg : the I2C address of the device. diff --git a/Documentation/devicetree/bindings/sound/nau8825.txt b/Documentation/devicetree/bindings/sound/nau8825.txt index d16d96839bcb..388a7bc60b1f 100644 --- a/Documentation/devicetree/bindings/sound/nau8825.txt +++ b/Documentation/devicetree/bindings/sound/nau8825.txt @@ -101,5 +101,5 @@ Example: nuvoton,crosstalk-enable; clock-names = "mclk"; - clocks = <&tegra_car TEGRA210_CLK_CLK_OUT_2>; + clocks = <&tegra_pmc TEGRA_PMC_CLK_OUT_2>; }; diff --git a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt index a8f2b0c56c79..bbd581a8c5bc 100644 --- a/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt +++ b/Documentation/devicetree/bindings/sound/nvidia,tegra-audio-wm8903.txt @@ -29,6 +29,7 @@ Optional properties: - nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in - nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone - nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone +- nvidia,headset : The Mic Jack represents state of the headset microphone pin Example: diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt index 21c648328be9..32c2cdb3d32f 100644 --- a/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt +++ b/Documentation/devicetree/bindings/sound/qcom,lpass-cpu.txt @@ -30,6 +30,8 @@ Required properties: - reg : Must contain an address for each entry in reg-names. - reg-names : A list which must include the following entries: * "lpass-lpaif" +- #address-cells : Must be 1 +- #size-cells : Must be 0 @@ -37,6 +39,20 @@ Optional properties: - qcom,adsp : Phandle for the audio DSP node +By default, the driver uses up to 4 MI2S SD lines, for a total of 8 channels. +The SD lines to use can be configured by adding subnodes for each of the DAIs. + +Required properties for each DAI (represented by a subnode): +- reg : Must be one of the DAI IDs + (usually part of dt-bindings header) +- qcom,playback-sd-lines: List of serial data lines to use for playback + Each SD line should be represented by a number from 0-3. +- qcom,capture-sd-lines : List of serial data lines to use for capture + Each SD line should be represented by a number from 0-3. + +Note that adding a subnode changes the default to "no lines configured", +so both playback and capture lines should be configured when a subnode is added. + Example: lpass@28100000 { @@ -51,4 +67,13 @@ lpass@28100000 { reg = <0x28100000 0x10000>; reg-names = "lpass-lpaif"; qcom,adsp = <&adsp>; + + #address-cells = <1>; + #size-cells = <0>; + + /* Optional to set different MI2S SD lines */ + dai@3 { + reg = <MI2S_QUATERNARY>; + qcom,playback-sd-lines = <0 1>; + }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6adm.txt b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt index bbae426cdfb1..15c353a20de8 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6adm.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6adm.txt @@ -29,7 +29,7 @@ used by the apr service device. Definition: Must be 0 = EXAMPLE -q6adm@8 { +apr-service@8 { compatible = "qcom,q6adm"; reg = <APR_SVC_ADM>; q6routing: routing { diff --git a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt index d74888b9f1bb..4916dd6a0896 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6afe.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6afe.txt @@ -100,7 +100,7 @@ configuration of each dai. Must contain the following properties. = EXAMPLE -q6afe@4 { +apr-service@4 { compatible = "qcom,q6afe"; reg = <APR_SVC_AFE>; @@ -110,12 +110,12 @@ q6afe@4 { #address-cells = <1>; #size-cells = <0>; - hdmi@1 { - reg = <1>; + dai@1 { + reg = <HDMI_RX>; }; - tdm@24 { - reg = <24>; + dai@24 { + reg = <PRIMARY_TDM_RX_0>; qcom,tdm-sync-mode = <1>: qcom,tdm-sync-src = <1>; qcom,tdm-data-out = <0>; @@ -125,8 +125,8 @@ q6afe@4 { }; - tdm@25 { - reg = <25>; + dai@25 { + reg = <PRIMARY_TDM_TX_0>; qcom,tdm-sync-mode = <1>: qcom,tdm-sync-src = <1>; qcom,tdm-data-out = <0>; @@ -135,43 +135,43 @@ q6afe@4 { qcom,tdm-data-align = <0>; }; - prim-mi2s-rx@16 { - reg = <16>; + dai@16 { + reg = <PRIMARY_MI2S_RX>; qcom,sd-lines = <0 2>; }; - prim-mi2s-tx@17 { - reg = <17>; + dai@17 { + reg = <PRIMARY_MI2S_TX>; qcom,sd-lines = <1>; }; - sec-mi2s-rx@18 { - reg = <18>; + dai@18 { + reg = <SECONDARY_MI2S_RX>; qcom,sd-lines = <0 3>; }; - sec-mi2s-tx@19 { - reg = <19>; + dai@19 { + reg = <SECONDARY_MI2S_TX>; qcom,sd-lines = <1>; }; - tert-mi2s-rx@20 { - reg = <20>; + dai@20 { + reg = <TERTIARY_MI2S_RX>; qcom,sd-lines = <1 3>; }; - tert-mi2s-tx@21 { - reg = <21>; + dai@21 { + reg = <TERTIARY_MI2S_TX>; qcom,sd-lines = <0>; }; - quat-mi2s-rx@22 { - reg = <22>; + dai@22 { + reg = <QUATERNARY_MI2S_RX>; qcom,sd-lines = <0>; }; - quat-mi2s-tx@23 { - reg = <23>; + dai@23 { + reg = <QUATERNARY_MI2S_TX>; qcom,sd-lines = <1>; }; }; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt index 9f5378c51686..6b9a88d0ea3f 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6asm.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6asm.txt @@ -51,13 +51,16 @@ configuration of each dai. Must contain the following properties. = EXAMPLE -q6asm@7 { +apr-service@7 { compatible = "qcom,q6asm"; reg = <APR_SVC_ASM>; q6asmdai: dais { compatible = "qcom,q6asm-dais"; + #address-cells = <1>; + #size-cells = <0>; #sound-dai-cells = <1>; - mm@0 { + + dai@0 { reg = <0>; direction = <2>; is-compress-dai; diff --git a/Documentation/devicetree/bindings/sound/qcom,q6core.txt b/Documentation/devicetree/bindings/sound/qcom,q6core.txt index 7f36ff8bec18..5cd4cc9b1fde 100644 --- a/Documentation/devicetree/bindings/sound/qcom,q6core.txt +++ b/Documentation/devicetree/bindings/sound/qcom,q6core.txt @@ -15,7 +15,7 @@ used by the apr service device. example "qcom,q6core-v2.0" = EXAMPLE -q6core@3 { +apr-service@3 { compatible = "qcom,q6core"; reg = <APR_SVC_ADSP_CORE>; }; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index 797fd035434c..1596f0d1e2fe 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -263,6 +263,7 @@ Required properties: "renesas,rcar_sound-gen2" if generation2 (or RZ/G1) "renesas,rcar_sound-gen3" if generation3 (or RZ/G2) Examples with soctypes are: + - "renesas,rcar_sound-r8a7742" (RZ/G1H) - "renesas,rcar_sound-r8a7743" (RZ/G1M) - "renesas,rcar_sound-r8a7744" (RZ/G1N) - "renesas,rcar_sound-r8a7745" (RZ/G1E) diff --git a/Documentation/devicetree/bindings/sound/rockchip-i2s.yaml b/Documentation/devicetree/bindings/sound/rockchip-i2s.yaml index a3ba2186d6a1..10f9d3ad0d48 100644 --- a/Documentation/devicetree/bindings/sound/rockchip-i2s.yaml +++ b/Documentation/devicetree/bindings/sound/rockchip-i2s.yaml @@ -24,6 +24,7 @@ properties: - rockchip,rk3188-i2s - rockchip,rk3228-i2s - rockchip,rk3288-i2s + - rockchip,rk3308-i2s - rockchip,rk3328-i2s - rockchip,rk3366-i2s - rockchip,rk3368-i2s @@ -47,14 +48,15 @@ properties: - const: i2s_hclk dmas: - items: - - description: TX DMA Channel - - description: RX DMA Channel + minItems: 1 + maxItems: 2 dma-names: - items: - - const: tx + oneOf: - const: rx + - items: + - const: tx + - const: rx power-domains: maxItems: 1 diff --git a/Documentation/devicetree/bindings/sound/rt1016.txt b/Documentation/devicetree/bindings/sound/rt1016.txt new file mode 100644 index 000000000000..2310f8ff259b --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rt1016.txt @@ -0,0 +1,17 @@ +RT1016 Stereo Class D Audio Amplifier + +This device supports I2C only. + +Required properties: + +- compatible : "realtek,rt1016". + +- reg : The I2C address of the device. + + +Example: + +rt1016: codec@1a { + compatible = "realtek,rt1016"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/sound/rt1308.txt b/Documentation/devicetree/bindings/sound/rt1308.txt index 2d46084afce4..2d46084afce4 100755..100644 --- a/Documentation/devicetree/bindings/sound/rt1308.txt +++ b/Documentation/devicetree/bindings/sound/rt1308.txt diff --git a/Documentation/devicetree/bindings/sound/simple-card.txt b/Documentation/devicetree/bindings/sound/simple-card.txt deleted file mode 100644 index 79954cd6e37b..000000000000 --- a/Documentation/devicetree/bindings/sound/simple-card.txt +++ /dev/null @@ -1,351 +0,0 @@ -Simple-Card: - -Simple-Card specifies audio DAI connections of SoC <-> codec. - -Required properties: - -- compatible : "simple-audio-card" - -Optional properties: - -- simple-audio-card,name : User specified audio sound card name, one string - property. -- simple-audio-card,widgets : Please refer to widgets.txt. -- simple-audio-card,routing : A list of the connections between audio components. - Each entry is a pair of strings, the first being the - connection's sink, the second being the connection's - source. -- simple-audio-card,mclk-fs : Multiplication factor between stream rate and codec - mclk. When defined, mclk-fs property defined in - dai-link sub nodes are ignored. -- simple-audio-card,hp-det-gpio : Reference to GPIO that signals when - headphones are attached. -- simple-audio-card,mic-det-gpio : Reference to GPIO that signals when - a microphone is attached. -- simple-audio-card,aux-devs : List of phandles pointing to auxiliary devices, such - as amplifiers, to be added to the sound card. -- simple-audio-card,pin-switches : List of strings containing the widget names for - which pin switches must be created. - -Optional subnodes: - -- simple-audio-card,dai-link : Container for dai-link level - properties and the CPU and CODEC - sub-nodes. This container may be - omitted when the card has only one - DAI link. See the examples and the - section below. - -Dai-link subnode properties and subnodes: - -If dai-link subnode is omitted and the subnode properties are directly -under "sound"-node the subnode property and subnode names have to be -prefixed with "simple-audio-card,"-prefix. - -Required dai-link subnodes: - -- cpu : CPU sub-node -- codec : CODEC sub-node - -Optional dai-link subnode properties: - -- format : CPU/CODEC common audio format. - "i2s", "right_j", "left_j" , "dsp_a" - "dsp_b", "ac97", "pdm", "msb", "lsb" -- frame-master : Indicates dai-link frame master. - phandle to a cpu or codec subnode. -- bitclock-master : Indicates dai-link bit clock master. - phandle to a cpu or codec subnode. -- bitclock-inversion : bool property. Add this if the - dai-link uses bit clock inversion. -- frame-inversion : bool property. Add this if the - dai-link uses frame clock inversion. -- mclk-fs : Multiplication factor between stream - rate and codec mclk, applied only for - the dai-link. - -For backward compatibility the frame-master and bitclock-master -properties can be used as booleans in codec subnode to indicate if the -codec is the dai-link frame or bit clock master. In this case there -should be no dai-link node, the same properties should not be present -at sound-node level, and the bitclock-inversion and frame-inversion -properties should also be placed in the codec node if needed. - -Required CPU/CODEC subnodes properties: - -- sound-dai : phandle and port of CPU/CODEC - -Optional CPU/CODEC subnodes properties: - -- dai-tdm-slot-num : Please refer to tdm-slot.txt. -- dai-tdm-slot-width : Please refer to tdm-slot.txt. -- clocks / system-clock-frequency : specify subnode's clock if needed. - it can be specified via "clocks" if system has - clock node (= common clock), or "system-clock-frequency" - (if system doens't support common clock) - If a clock is specified, it is - enabled with clk_prepare_enable() - in dai startup() and disabled with - clk_disable_unprepare() in dai - shutdown(). - If a clock is specified and a - multiplication factor is given with - mclk-fs, the clock will be set to the - calculated mclk frequency when the - stream starts. -- system-clock-direction-out : specifies clock direction as 'out' on - initialization. It is useful for some aCPUs with - fixed clocks. - -------------------------------------------- -Example 1 - single DAI link: -------------------------------------------- - -sound { - compatible = "simple-audio-card"; - simple-audio-card,name = "VF610-Tower-Sound-Card"; - simple-audio-card,format = "left_j"; - simple-audio-card,bitclock-master = <&dailink0_master>; - simple-audio-card,frame-master = <&dailink0_master>; - simple-audio-card,widgets = - "Microphone", "Microphone Jack", - "Headphone", "Headphone Jack", - "Speaker", "External Speaker"; - simple-audio-card,routing = - "MIC_IN", "Microphone Jack", - "Headphone Jack", "HP_OUT", - "External Speaker", "LINE_OUT"; - - simple-audio-card,cpu { - sound-dai = <&sh_fsi2 0>; - }; - - dailink0_master: simple-audio-card,codec { - sound-dai = <&ak4648>; - clocks = <&osc>; - }; -}; - -&i2c0 { - ak4648: ak4648@12 { - #sound-dai-cells = <0>; - compatible = "asahi-kasei,ak4648"; - reg = <0x12>; - }; -}; - -sh_fsi2: sh_fsi2@ec230000 { - #sound-dai-cells = <1>; - compatible = "renesas,sh_fsi2"; - reg = <0xec230000 0x400>; - interrupt-parent = <&gic>; - interrupts = <0 146 0x4>; -}; - -------------------------------------------- -Example 2 - many DAI links: -------------------------------------------- - -sound { - compatible = "simple-audio-card"; - simple-audio-card,name = "Cubox Audio"; - - simple-audio-card,dai-link@0 { /* I2S - HDMI */ - reg = <0>; - format = "i2s"; - cpu { - sound-dai = <&audio1 0>; - }; - codec { - sound-dai = <&tda998x 0>; - }; - }; - - simple-audio-card,dai-link@1 { /* S/PDIF - HDMI */ - reg = <1>; - cpu { - sound-dai = <&audio1 1>; - }; - codec { - sound-dai = <&tda998x 1>; - }; - }; - - simple-audio-card,dai-link@2 { /* S/PDIF - S/PDIF */ - reg = <2>; - cpu { - sound-dai = <&audio1 1>; - }; - codec { - sound-dai = <&spdif_codec>; - }; - }; -}; - -------------------------------------------- -Example 3 - route audio from IMX6 SSI2 through TLV320DAC3100 codec -through TPA6130A2 amplifier to headphones: -------------------------------------------- - -&i2c0 { - codec: tlv320dac3100@18 { - compatible = "ti,tlv320dac3100"; - ... - } - - amp: tpa6130a2@60 { - compatible = "ti,tpa6130a2"; - ... - } -} - -sound { - compatible = "simple-audio-card"; - ... - simple-audio-card,widgets = - "Headphone", "Headphone Jack"; - simple-audio-card,routing = - "Headphone Jack", "HPLEFT", - "Headphone Jack", "HPRIGHT", - "LEFTIN", "HPL", - "RIGHTIN", "HPR"; - simple-audio-card,aux-devs = <&>; - simple-audio-card,cpu { - sound-dai = <&ssi2>; - }; - simple-audio-card,codec { - sound-dai = <&codec>; - clocks = ... - }; -}; - -------------------------------------------- -Example 4. Sampling Rate Conversion -------------------------------------------- - -sound { - compatible = "simple-audio-card"; - - simple-audio-card,name = "rsnd-ak4643"; - simple-audio-card,format = "left_j"; - simple-audio-card,bitclock-master = <&sndcodec>; - simple-audio-card,frame-master = <&sndcodec>; - - simple-audio-card,convert-rate = <48000>; - - simple-audio-card,prefix = "ak4642"; - simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", - "DAI0 Capture", "ak4642 Capture"; - - sndcpu: simple-audio-card,cpu { - sound-dai = <&rcar_sound>; - }; - - sndcodec: simple-audio-card,codec { - sound-dai = <&ak4643>; - system-clock-frequency = <11289600>; - }; -}; - -------------------------------------------- -Example 5. 2 CPU 1 Codec (Mixing) -------------------------------------------- -sound { - compatible = "simple-audio-card"; - - simple-audio-card,name = "rsnd-ak4643"; - simple-audio-card,format = "left_j"; - simple-audio-card,bitclock-master = <&dpcmcpu>; - simple-audio-card,frame-master = <&dpcmcpu>; - - simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", - "ak4642 Playback", "DAI1 Playback"; - - dpcmcpu: cpu@0 { - sound-dai = <&rcar_sound 0>; - }; - - cpu@1 { - sound-dai = <&rcar_sound 1>; - }; - - codec { - prefix = "ak4642"; - sound-dai = <&ak4643>; - clocks = <&audio_clock>; - }; -}; - -------------------------------------------- -Example 6 - many DAI links with DPCM: -------------------------------------------- - -CPU0 ------ ak4613 -CPU1 ------ PCM3168A-p /* DPCM 1ch/2ch */ -CPU2 --/ /* DPCM 3ch/4ch */ -CPU3 --/ /* DPCM 5ch/6ch */ -CPU4 --/ /* DPCM 7ch/8ch */ -CPU5 ------ PCM3168A-c - -sound { - compatible = "simple-audio-card"; - - simple-audio-card,routing = - "pcm3168a Playback", "DAI1 Playback", - "pcm3168a Playback", "DAI2 Playback", - "pcm3168a Playback", "DAI3 Playback", - "pcm3168a Playback", "DAI4 Playback"; - - simple-audio-card,dai-link@0 { - format = "left_j"; - bitclock-master = <&sndcpu0>; - frame-master = <&sndcpu0>; - - sndcpu0: cpu { - sound-dai = <&rcar_sound 0>; - }; - codec { - sound-dai = <&ak4613>; - }; - }; - simple-audio-card,dai-link@1 { - format = "i2s"; - bitclock-master = <&sndcpu1>; - frame-master = <&sndcpu1>; - - convert-channels = <8>; /* TDM Split */ - - sndcpu1: cpu@0 { - sound-dai = <&rcar_sound 1>; - }; - cpu@1 { - sound-dai = <&rcar_sound 2>; - }; - cpu@2 { - sound-dai = <&rcar_sound 3>; - }; - cpu@3 { - sound-dai = <&rcar_sound 4>; - }; - codec { - mclk-fs = <512>; - prefix = "pcm3168a"; - dai-tdm-slot-num = <8>; - sound-dai = <&pcm3168a 0>; - }; - }; - simple-audio-card,dai-link@2 { - format = "i2s"; - bitclock-master = <&sndcpu2>; - frame-master = <&sndcpu2>; - - sndcpu2: cpu { - sound-dai = <&rcar_sound 5>; - }; - codec { - mclk-fs = <512>; - prefix = "pcm3168a"; - sound-dai = <&pcm3168a 1>; - }; - }; -}; diff --git a/Documentation/devicetree/bindings/sound/simple-card.yaml b/Documentation/devicetree/bindings/sound/simple-card.yaml new file mode 100644 index 000000000000..cb2bb5fac0e1 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/simple-card.yaml @@ -0,0 +1,484 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/simple-card.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Simple Audio Card Driver Device Tree Bindings + +maintainers: + - Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> + +definitions: + + frame-master: + description: Indicates dai-link frame master. + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle-array + - maxItems: 1 + + bitclock-master: + description: Indicates dai-link bit clock master + allOf: + - $ref: /schemas/types.yaml#/definitions/phandle-array + - maxItems: 1 + + frame-inversion: + description: dai-link uses frame clock inversion + $ref: /schemas/types.yaml#/definitions/flag + + bitclock-inversion: + description: dai-link uses bit clock inversion + $ref: /schemas/types.yaml#/definitions/flag + + dai-tdm-slot-num: + description: see tdm-slot.txt. + $ref: /schemas/types.yaml#/definitions/uint32 + + dai-tdm-slot-width: + description: see tdm-slot.txt. + $ref: /schemas/types.yaml#/definitions/uint32 + + system-clock-frequency: + description: | + If a clock is specified and a multiplication factor is given with + mclk-fs, the clock will be set to the calculated mclk frequency + when the stream starts. + $ref: /schemas/types.yaml#/definitions/uint32 + + system-clock-direction-out: + description: | + specifies clock direction as 'out' on initialization. + It is useful for some aCPUs with fixed clocks. + $ref: /schemas/types.yaml#/definitions/flag + + mclk-fs: + description: | + Multiplication factor between stream rate and codec mclk. + When defined, mclk-fs property defined in dai-link sub nodes are ignored. + $ref: /schemas/types.yaml#/definitions/uint32 + + aux-devs: + description: | + List of phandles pointing to auxiliary devices, such + as amplifiers, to be added to the sound card. + $ref: /schemas/types.yaml#/definitions/phandle-array + + convert-rate: + description: CPU to Codec rate convert. + $ref: /schemas/types.yaml#/definitions/uint32 + + convert-channels: + description: CPU to Codec rate channels. + $ref: /schemas/types.yaml#/definitions/uint32 + + prefix: + description: "device name prefix" + $ref: /schemas/types.yaml#/definitions/string + + label: + maxItems: 1 + + routing: + description: | + A list of the connections between audio components. + Each entry is a pair of strings, the first being the + connection's sink, the second being the connection's source. + $ref: /schemas/types.yaml#/definitions/non-unique-string-array + + widgets: + description: User specified audio sound widgets. + $ref: /schemas/types.yaml#/definitions/non-unique-string-array + + pin-switches: + description: the widget names for which pin switches must be created. + $ref: /schemas/types.yaml#/definitions/string-array + + format: + description: audio format. + items: + enum: + - i2s + - right_j + - left_j + - dsp_a + - dsp_b + - ac97 + - pdm + - msb + - lsb + + dai: + type: object + properties: + sound-dai: + maxItems: 1 + + # common properties + mclk-fs: + $ref: "#/definitions/mclk-fs" + prefix: + $ref: "#/definitions/prefix" + frame-inversion: + $ref: "#/definitions/frame-inversion" + bitclock-inversion: + $ref: "#/definitions/bitclock-inversion" + frame-master: + $ref: /schemas/types.yaml#/definitions/flag + bitclock-master: + $ref: /schemas/types.yaml#/definitions/flag + + dai-tdm-slot-num: + $ref: "#/definitions/dai-tdm-slot-num" + dai-tdm-slot-width: + $ref: "#/definitions/dai-tdm-slot-width" + clocks: + maxItems: 1 + system-clock-frequency: + $ref: "#/definitions/system-clock-frequency" + system-clock-direction-out: + $ref: "#/definitions/system-clock-direction-out" + required: + - sound-dai + +properties: + compatible: + contains: + enum: + - simple-audio-card + - simple-scu-audio-card + + "#address-cells": + const: 1 + "#size-cells": + const: 0 + + label: + $ref: "#/definitions/label" + + simple-audio-card,name: + description: User specified audio sound card name. + $ref: /schemas/types.yaml#/definitions/string + +# use patternProperties to avoid naming "xxx,yyy" issue +patternProperties: + "^simple-audio-card,widgets$": + $ref: "#/definitions/widgets" + "^simple-audio-card,routing$": + $ref: "#/definitions/routing" + "^simple-audio-card,cpu(@[0-9a-f]+)?": + $ref: "#/definitions/dai" + "^simple-audio-card,codec(@[0-9a-f]+)?": + $ref: "#/definitions/dai" + + # common properties + "^simple-audio-card,frame-master$": + $ref: "#/definitions/frame-master" + "^simple-audio-card,bitclock-master$": + $ref: "#/definitions/bitclock-master" + "^simple-audio-card,frame-inversion$": + $ref: "#/definitions/frame-inversion" + "^simple-audio-card,bitclock-inversion$": + $ref: "#/definitions/bitclock-inversion" + "^simple-audio-card,format$": + $ref: "#/definitions/format" + "^simple-audio-card,mclk-fs$": + $ref: "#/definitions/mclk-fs" + "^simple-audio-card,aux-devs$": + $ref: "#/definitions/aux-devs" + "^simple-audio-card,convert-rate$": + $ref: "#/definitions/convert-rate" + "^simple-audio-card,convert-channels$": + $ref: "#/definitions/convert-channels" + "^simple-audio-card,prefix$": + $ref: "#/definitions/prefix" + "^simple-audio-card,pin-switches$": + $ref: "#/definitions/pin-switches" + "^simple-audio-card,hp-det-gpio$": + maxItems: 1 + "^simple-audio-card,mic-det-gpio$": + maxItems: 1 + + "^simple-audio-card,dai-link(@[0-9a-f]+)?$": + description: | + Container for dai-link level properties and the CPU and CODEC sub-nodes. + This container may be omitted when the card has only one DAI link. + type: object + properties: + reg: + maxItems: 1 + + # common properties + frame-master: + $ref: "#/definitions/frame-master" + bitclock-master: + $ref: "#/definitions/bitclock-master" + frame-inversion: + $ref: "#/definitions/frame-inversion" + bitclock-inversion: + $ref: "#/definitions/bitclock-inversion" + format: + $ref: "#/definitions/format" + mclk-fs: + $ref: "#/definitions/mclk-fs" + aux-devs: + $ref: "#/definitions/aux-devs" + convert-rate: + $ref: "#/definitions/convert-rate" + convert-channels: + $ref: "#/definitions/convert-channels" + prefix: + $ref: "#/definitions/prefix" + pin-switches: + $ref: "#/definitions/pin-switches" + hp-det-gpio: + maxItems: 1 + mic-det-gpio: + maxItems: 1 + + patternProperties: + "^cpu(@[0-9a-f]+)?": + $ref: "#/definitions/dai" + "^codec(@[0-9a-f]+)?": + $ref: "#/definitions/dai" + additionalProperties: false + +required: + - compatible + +additionalProperties: false + +examples: +#-------------------- +# single DAI link +#-------------------- + - | + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "VF610-Tower-Sound-Card"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&dailink0_master>; + simple-audio-card,frame-master = <&dailink0_master>; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "Headphone Jack", "HP_OUT", + "External Speaker", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&sh_fsi2 0>; + }; + + dailink0_master: simple-audio-card,codec { + sound-dai = <&ak4648>; + clocks = <&osc>; + }; + }; + +#-------------------- +# Multi DAI links +#-------------------- + - | + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "Cubox Audio"; + + #address-cells = <1>; + #size-cells = <0>; + + simple-audio-card,dai-link@0 { /* I2S - HDMI */ + reg = <0>; + format = "i2s"; + cpu { + sound-dai = <&audio0>; + }; + codec { + sound-dai = <&tda998x0>; + }; + }; + + simple-audio-card,dai-link@1 { /* S/PDIF - HDMI */ + reg = <1>; + cpu { + sound-dai = <&audio1>; + }; + codec { + sound-dai = <&tda998x1>; + }; + }; + + simple-audio-card,dai-link@2 { /* S/PDIF - S/PDIF */ + reg = <2>; + cpu { + sound-dai = <&audio2>; + }; + codec { + sound-dai = <&spdif_codec>; + }; + }; + }; + +#-------------------- +# route audio from IMX6 SSI2 through TLV320DAC3100 codec +# through TPA6130A2 amplifier to headphones: +#-------------------- + - | + sound { + compatible = "simple-audio-card"; + + simple-audio-card,widgets = + "Headphone", "Headphone Jack"; + simple-audio-card,routing = + "Headphone Jack", "HPLEFT", + "Headphone Jack", "HPRIGHT", + "LEFTIN", "HPL", + "RIGHTIN", "HPR"; + simple-audio-card,aux-devs = <&>; + simple-audio-card,cpu { + sound-dai = <&ssi2>; + }; + simple-audio-card,codec { + sound-dai = <&codec>; + clocks = <&clocks>; + }; + }; + +#-------------------- +# Sampling Rate Conversion +#-------------------- + - | + sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "rsnd-ak4643"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + simple-audio-card,convert-rate = <48000>; + + simple-audio-card,prefix = "ak4642"; + simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", + "DAI0 Capture", "ak4642 Capture"; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&ak4643>; + system-clock-frequency = <11289600>; + }; + }; + +#-------------------- +# 2 CPU 1 Codec (Mixing) +#-------------------- + - | + sound { + compatible = "simple-audio-card"; + + simple-audio-card,name = "rsnd-ak4643"; + simple-audio-card,format = "left_j"; + simple-audio-card,bitclock-master = <&dpcmcpu>; + simple-audio-card,frame-master = <&dpcmcpu>; + + simple-audio-card,convert-rate = <48000>; + simple-audio-card,convert-channels = <2>; + + simple-audio-card,routing = "ak4642 Playback", "DAI0 Playback", + "ak4642 Playback", "DAI1 Playback"; + + dpcmcpu: simple-audio-card,cpu@0 { + sound-dai = <&rcar_sound 0>; + }; + + simple-audio-card,cpu@1 { + sound-dai = <&rcar_sound 1>; + }; + + simple-audio-card,codec { + prefix = "ak4642"; + sound-dai = <&ak4643>; + clocks = <&audio_clock>; + }; + }; + +#-------------------- +# Multi DAI links with DPCM: +# +# CPU0 ------ ak4613 +# CPU1 ------ PCM3168A-p /* DPCM 1ch/2ch */ +# CPU2 --/ /* DPCM 3ch/4ch */ +# CPU3 --/ /* DPCM 5ch/6ch */ +# CPU4 --/ /* DPCM 7ch/8ch */ +# CPU5 ------ PCM3168A-c +#-------------------- + - | + sound { + compatible = "simple-audio-card"; + + simple-audio-card,routing = + "pcm3168a Playback", "DAI1 Playback", + "pcm3168a Playback", "DAI2 Playback", + "pcm3168a Playback", "DAI3 Playback", + "pcm3168a Playback", "DAI4 Playback"; + + simple-audio-card,dai-link@0 { + format = "left_j"; + bitclock-master = <&sndcpu0>; + frame-master = <&sndcpu0>; + + sndcpu0: cpu { + sound-dai = <&rcar_sound 0>; + }; + codec { + sound-dai = <&ak4613>; + }; + }; + + simple-audio-card,dai-link@1 { + format = "i2s"; + bitclock-master = <&sndcpu1>; + frame-master = <&sndcpu1>; + + convert-channels = <8>; /* TDM Split */ + + sndcpu1: cpu@0 { + sound-dai = <&rcar_sound 1>; + }; + cpu@1 { + sound-dai = <&rcar_sound 2>; + }; + cpu@2 { + sound-dai = <&rcar_sound 3>; + }; + cpu@3 { + sound-dai = <&rcar_sound 4>; + }; + codec { + mclk-fs = <512>; + prefix = "pcm3168a"; + dai-tdm-slot-num = <8>; + sound-dai = <&pcm3168a 0>; + }; + }; + + simple-audio-card,dai-link@2 { + format = "i2s"; + bitclock-master = <&sndcpu2>; + frame-master = <&sndcpu2>; + + sndcpu2: cpu { + sound-dai = <&rcar_sound 5>; + }; + codec { + mclk-fs = <512>; + prefix = "pcm3168a"; + sound-dai = <&pcm3168a 1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml index ab2268c0ee67..306ac3d006dc 100644 --- a/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml +++ b/Documentation/devicetree/bindings/sound/tlv320adcx140.yaml @@ -63,6 +63,55 @@ properties: - $ref: /schemas/types.yaml#/definitions/uint32 - enum: [0, 1, 2] + ti,pdm-edge-select: + description: | + Defines the PDMCLK sampling edge configuration for the PDM inputs. This + array is defined as <PDMIN1 PDMIN2 PDMIN3 PDMIN4>. + + 0 - (default) Odd channel is latched on the negative edge and even + channel is latched on the the positive edge. + 1 - Odd channel is latched on the positive edge and even channel is + latched on the the negative edge. + + PDMIN1 - PDMCLK latching edge used for channel 1 and 2 data + PDMIN2 - PDMCLK latching edge used for channel 3 and 4 data + PDMIN3 - PDMCLK latching edge used for channel 5 and 6 data + PDMIN4 - PDMCLK latching edge used for channel 7 and 8 data + + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 1 + maxItems: 4 + items: + maximum: 1 + default: [0, 0, 0, 0] + + ti,gpi-config: + description: | + Defines the configuration for the general purpose input pins (GPI). + The array is defined as <GPI1 GPI2 GPI3 GPI4>. + + 0 - (default) disabled + 1 - GPIX is configured as a general-purpose input (GPI) + 2 - GPIX is configured as a master clock input (MCLK) + 3 - GPIX is configured as an ASI input for daisy-chain (SDIN) + 4 - GPIX is configured as a PDM data input for channel 1 and channel + (PDMDIN1) + 5 - GPIX is configured as a PDM data input for channel 3 and channel + (PDMDIN2) + 6 - GPIX is configured as a PDM data input for channel 5 and channel + (PDMDIN3) + 7 - GPIX is configured as a PDM data input for channel 7 and channel + (PDMDIN4) + + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32-array + - minItems: 1 + maxItems: 4 + items: + maximum: 7 + default: [0, 0, 0, 0] + required: - compatible - reg @@ -77,6 +126,8 @@ examples: compatible = "ti,tlv320adc5140"; reg = <0x4c>; ti,mic-bias-source = <6>; + ti,pdm-edge-select = <0 1 0 1>; + ti,gpi-config = <4 5 6 7>; reset-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; }; }; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt index 68cccc4653ba..367b58ce1bb9 100644 --- a/Documentation/devicetree/bindings/sound/wm8994.txt +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -14,9 +14,15 @@ Required properties: - #gpio-cells : Must be 2. The first cell is the pin number and the second cell is used to specify optional parameters (currently unused). - - AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, CPVDD-supply, - SPKVDD1-supply, SPKVDD2-supply : power supplies for the device, as covered - in Documentation/devicetree/bindings/regulator/regulator.txt + - power supplies for the device, as covered in + Documentation/devicetree/bindings/regulator/regulator.txt, depending + on compatible: + - for wlf,wm1811 and wlf,wm8958: + AVDD1-supply, AVDD2-supply, DBVDD1-supply, DBVDD2-supply, DBVDD3-supply, + DCVDD-supply, CPVDD-supply, SPKVDD1-supply, SPKVDD2-supply + - for wlf,wm8994: + AVDD1-supply, AVDD2-supply, DBVDD-supply, DCVDD-supply, CPVDD-supply, + SPKVDD1-supply, SPKVDD2-supply Optional properties: @@ -73,11 +79,11 @@ wm8994: codec@1a { lineout1-se; + AVDD1-supply = <®ulator>; AVDD2-supply = <®ulator>; CPVDD-supply = <®ulator>; - DBVDD1-supply = <®ulator>; - DBVDD2-supply = <®ulator>; - DBVDD3-supply = <®ulator>; + DBVDD-supply = <®ulator>; + DCVDD-supply = <®ulator>; SPKVDD1-supply = <®ulator>; SPKVDD2-supply = <®ulator>; }; diff --git a/Documentation/devicetree/bindings/sound/zl38060.yaml b/Documentation/devicetree/bindings/sound/zl38060.yaml new file mode 100644 index 000000000000..338e2a13c775 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/zl38060.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/sound/zl38060.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ZL38060 Connected Home Audio Processor from Microsemi. + +description: | + The ZL38060 is a "Connected Home Audio Processor" from Microsemi, + which consists of a Digital Signal Processor (DSP), several Digital + Audio Interfaces (DAIs), analog outputs, and a block of 14 GPIOs. + +maintainers: + - Jaroslav Kysela <perex@perex.cz> + - Takashi Iwai <tiwai@suse.com> + +properties: + compatible: + const: mscc,zl38060 + + reg: + description: + SPI device address. + maxItems: 1 + + spi-max-frequency: + maximum: 24000000 + + reset-gpios: + description: + A GPIO line handling reset of the chip. As the line is active low, + it should be marked GPIO_ACTIVE_LOW (see ../gpio/gpio.txt) + maxItems: 1 + + '#gpio-cells': + const: 2 + + gpio-controller: true + + '#sound-dai-cells': + const: 0 + +required: + - compatible + - reg + - '#gpio-cells' + - gpio-controller + - '#sound-dai-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + spi0 { + #address-cells = <1>; + #size-cells = <0>; + + codec: zl38060@0 { + gpio-controller; + #gpio-cells = <2>; + #sound-dai-cells = <0>; + compatible = "mscc,zl38060"; + reg = <0>; + spi-max-frequency = <12000000>; + reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml b/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml new file mode 100644 index 000000000000..bec651541e0c --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/arm-smc-wdt.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/watchdog/arm-smc-wdt.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM Secure Monitor Call based watchdog + +allOf: + - $ref: "watchdog.yaml#" + +maintainers: + - Julius Werner <jwerner@chromium.org> + +properties: + compatible: + enum: + - arm,smc-wdt + arm,smc-id: + allOf: + - $ref: /schemas/types.yaml#/definitions/uint32 + description: | + The ATF smc function id used by the firmware. + Defaults to 0x82003D06 if unset. + +required: + - compatible + +examples: + - | + watchdog { + compatible = "arm,smc-wdt"; + arm,smc-id = <0x82003D06>; + timeout-sec = <15>; + }; + +... diff --git a/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt b/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt index 79b3c62f183d..e42fd3019cb7 100644 --- a/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/renesas,wdt.txt @@ -5,6 +5,7 @@ Required properties: fallback compatible string when compatible with the generic version. Examples with soctypes are: + - "renesas,r8a7742-wdt" (RZ/G1H) - "renesas,r8a7743-wdt" (RZ/G1M) - "renesas,r8a7744-wdt" (RZ/G1N) - "renesas,r8a7745-wdt" (RZ/G1E) diff --git a/Documentation/filesystems/proc.rst b/Documentation/filesystems/proc.rst index 430963e0e8c3..996f3cfe7030 100644 --- a/Documentation/filesystems/proc.rst +++ b/Documentation/filesystems/proc.rst @@ -51,6 +51,8 @@ fixes/update part 1.1 Stefani Seibold <stefani@seibold.net> June 9 2009 4 Configuring procfs 4.1 Mount options + 5 Filesystem behavior + Preface ======= @@ -2143,28 +2145,80 @@ The following mount options are supported: ========= ======================================================== hidepid= Set /proc/<pid>/ access mode. gid= Set the group authorized to learn processes information. + subset= Show only the specified subset of procfs. ========= ======================================================== -hidepid=0 means classic mode - everybody may access all /proc/<pid>/ directories -(default). - -hidepid=1 means users may not access any /proc/<pid>/ directories but their -own. Sensitive files like cmdline, sched*, status are now protected against -other users. This makes it impossible to learn whether any user runs -specific program (given the program doesn't reveal itself by its behaviour). -As an additional bonus, as /proc/<pid>/cmdline is unaccessible for other users, -poorly written programs passing sensitive information via program arguments are -now protected against local eavesdroppers. - -hidepid=2 means hidepid=1 plus all /proc/<pid>/ will be fully invisible to other -users. It doesn't mean that it hides a fact whether a process with a specific -pid value exists (it can be learned by other means, e.g. by "kill -0 $PID"), -but it hides process' uid and gid, which may be learned by stat()'ing -/proc/<pid>/ otherwise. It greatly complicates an intruder's task of gathering -information about running processes, whether some daemon runs with elevated -privileges, whether other user runs some sensitive program, whether other users -run any program at all, etc. +hidepid=off or hidepid=0 means classic mode - everybody may access all +/proc/<pid>/ directories (default). + +hidepid=noaccess or hidepid=1 means users may not access any /proc/<pid>/ +directories but their own. Sensitive files like cmdline, sched*, status are now +protected against other users. This makes it impossible to learn whether any +user runs specific program (given the program doesn't reveal itself by its +behaviour). As an additional bonus, as /proc/<pid>/cmdline is unaccessible for +other users, poorly written programs passing sensitive information via program +arguments are now protected against local eavesdroppers. + +hidepid=invisible or hidepid=2 means hidepid=1 plus all /proc/<pid>/ will be +fully invisible to other users. It doesn't mean that it hides a fact whether a +process with a specific pid value exists (it can be learned by other means, e.g. +by "kill -0 $PID"), but it hides process' uid and gid, which may be learned by +stat()'ing /proc/<pid>/ otherwise. It greatly complicates an intruder's task of +gathering information about running processes, whether some daemon runs with +elevated privileges, whether other user runs some sensitive program, whether +other users run any program at all, etc. + +hidepid=ptraceable or hidepid=4 means that procfs should only contain +/proc/<pid>/ directories that the caller can ptrace. gid= defines a group authorized to learn processes information otherwise prohibited by hidepid=. If you use some daemon like identd which needs to learn information about processes information, just add identd to this group. + +subset=pid hides all top level files and directories in the procfs that +are not related to tasks. + +5 Filesystem behavior +---------------------------- + +Originally, before the advent of pid namepsace, procfs was a global file +system. It means that there was only one procfs instance in the system. + +When pid namespace was added, a separate procfs instance was mounted in +each pid namespace. So, procfs mount options are global among all +mountpoints within the same namespace. + +:: + +# grep ^proc /proc/mounts +proc /proc proc rw,relatime,hidepid=2 0 0 + +# strace -e mount mount -o hidepid=1 -t proc proc /tmp/proc +mount("proc", "/tmp/proc", "proc", 0, "hidepid=1") = 0 ++++ exited with 0 +++ + +# grep ^proc /proc/mounts +proc /proc proc rw,relatime,hidepid=2 0 0 +proc /tmp/proc proc rw,relatime,hidepid=2 0 0 + +and only after remounting procfs mount options will change at all +mountpoints. + +# mount -o remount,hidepid=1 -t proc proc /tmp/proc + +# grep ^proc /proc/mounts +proc /proc proc rw,relatime,hidepid=1 0 0 +proc /tmp/proc proc rw,relatime,hidepid=1 0 0 + +This behavior is different from the behavior of other filesystems. + +The new procfs behavior is more like other filesystems. Each procfs mount +creates a new procfs instance. Mount options affect own procfs instance. +It means that it became possible to have several procfs instances +displaying tasks with different filtering options in one pid namespace. + +# mount -o hidepid=invisible -t proc proc /proc +# mount -o hidepid=noaccess -t proc proc /tmp/proc +# grep ^proc /proc/mounts +proc /proc proc rw,relatime,hidepid=invisible 0 0 +proc /tmp/proc proc rw,relatime,hidepid=noaccess 0 0 diff --git a/Documentation/livepatch/module-elf-format.rst b/Documentation/livepatch/module-elf-format.rst index 2a591e6f8e6c..8c6b894c4661 100644 --- a/Documentation/livepatch/module-elf-format.rst +++ b/Documentation/livepatch/module-elf-format.rst @@ -14,8 +14,7 @@ This document outlines the Elf format requirements that livepatch modules must f 4. Livepatch symbols 4.1 A livepatch module's symbol table 4.2 Livepatch symbol format - 5. Architecture-specific sections - 6. Symbol table and Elf section access + 5. Symbol table and Elf section access 1. Background and motivation ============================ @@ -298,17 +297,7 @@ Examples: Note that the 'Ndx' (Section index) for these symbols is SHN_LIVEPATCH (0xff20). "OS" means OS-specific. -5. Architecture-specific sections -================================= -Architectures may override arch_klp_init_object_loaded() to perform -additional arch-specific tasks when a target module loads, such as applying -arch-specific sections. On x86 for example, we must apply per-object -.altinstructions and .parainstructions sections when a target module loads. -These sections must be prefixed with ".klp.arch.$objname." so that they can -be easily identified when iterating through a patch module's Elf sections -(See arch/x86/kernel/livepatch.c for a complete example). - -6. Symbol table and Elf section access +5. Symbol table and Elf section access ====================================== A livepatch module's symbol table is accessible through module->symtab. diff --git a/Documentation/security/keys/core.rst b/Documentation/security/keys/core.rst index d9b0b859018b..9367d0fe4a02 100644 --- a/Documentation/security/keys/core.rst +++ b/Documentation/security/keys/core.rst @@ -920,10 +920,14 @@ The keyctl syscall functions are: long keyctl(KEYCTL_PKEY_QUERY, key_serial_t key_id, unsigned long reserved, + const char *params, struct keyctl_pkey_query *info); - Get information about an asymmetric key. The information is returned in - the keyctl_pkey_query struct:: + Get information about an asymmetric key. Specific algorithms and + encodings may be queried by using the ``params`` argument. This is a + string containing a space- or tab-separated string of key-value pairs. + Currently supported keys include ``enc`` and ``hash``. The information + is returned in the keyctl_pkey_query struct:: __u32 supported_ops; __u32 key_size; diff --git a/Documentation/trace/ftrace.rst b/Documentation/trace/ftrace.rst index 3b5614b1d1a5..430a16283103 100644 --- a/Documentation/trace/ftrace.rst +++ b/Documentation/trace/ftrace.rst @@ -1524,7 +1524,7 @@ display-graph option:: => remove_vma => exit_mmap => mmput - => flush_old_exec + => begin_new_exec => load_elf_binary => search_binary_handler => __do_execve_file.isra.32 |