diff options
Diffstat (limited to 'arch/arm/boot/dts/qcom-ipq8064.dtsi')
-rw-r--r-- | arch/arm/boot/dts/qcom-ipq8064.dtsi | 327 |
1 files changed, 310 insertions, 17 deletions
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index 1e0a3b446f7a..f793cd1ad6d0 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -2,9 +2,13 @@ /dts-v1/; #include "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/clock/qcom,gcc-ipq806x.h> #include <dt-bindings/clock/qcom,lcc-ipq806x.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/reset/qcom,gcc-ipq806x.h> #include <dt-bindings/soc/qcom,gsbi.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> / { model = "Qualcomm IPQ8064"; @@ -43,7 +47,8 @@ cpu-pmu { compatible = "qcom,krait-pmu"; - interrupts = <1 10 0x304>; + interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_LEVEL_HIGH)>; }; reserved-memory { @@ -97,7 +102,7 @@ clock-names = "ahbix-clk", "mi2s-osr-clk", "mi2s-bit-clk"; - interrupts = <0 85 1>; + interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; interrupt-names = "lpass-irq-lpaif"; reg = <0x28100000 0x10000>; reg-names = "lpass-lpaif"; @@ -111,7 +116,62 @@ #gpio-cells = <2>; interrupt-controller; #interrupt-cells = <2>; - interrupts = <0 16 0x4>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + + pcie0_pins: pcie0_pinmux { + mux { + pins = "gpio3"; + function = "pcie1_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + pcie1_pins: pcie1_pinmux { + mux { + pins = "gpio48"; + function = "pcie2_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + pcie2_pins: pcie2_pinmux { + mux { + pins = "gpio63"; + function = "pcie3_rst"; + drive-strength = <12>; + bias-disable; + }; + }; + + spi_pins: spi_pins { + mux { + pins = "gpio18", "gpio19", "gpio21"; + function = "gsbi5"; + drive-strength = <10>; + bias-none; + }; + }; + + leds_pins: leds_pins { + mux { + pins = "gpio7", "gpio8", "gpio9", + "gpio26", "gpio53"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + output-low; + }; + }; + + buttons_pins: buttons_pins { + mux { + pins = "gpio54"; + drive-strength = <2>; + bias-pull-up; + }; + }; }; intc: interrupt-controller@2000000 { @@ -125,11 +185,16 @@ timer@200a000 { compatible = "qcom,kpss-timer", "qcom,kpss-wdt-ipq8064", "qcom,msm-timer"; - interrupts = <1 1 0x301>, - <1 2 0x301>, - <1 3 0x301>, - <1 4 0x301>, - <1 5 0x301>; + interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_EDGE_RISING)>, + <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_EDGE_RISING)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_EDGE_RISING)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_EDGE_RISING)>, + <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) | + IRQ_TYPE_EDGE_RISING)>; reg = <0x0200a000 0x100>; clock-frequency = <25000000>, <32768>; @@ -177,7 +242,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x12490000 0x1000>, <0x12480000 0x1000>; - interrupts = <0 195 0x0>; + interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -186,7 +251,7 @@ i2c@124a0000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x124a0000 0x1000>; - interrupts = <0 196 0>; + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; clock-names = "core", "iface"; @@ -215,7 +280,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16340000 0x1000>, <0x16300000 0x1000>; - interrupts = <0 152 0x0>; + interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -224,7 +289,7 @@ i2c@16380000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x16380000 0x1000>; - interrupts = <0 153 0>; + interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; clock-names = "core", "iface"; @@ -252,7 +317,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x1a240000 0x1000>, <0x1a200000 0x1000>; - interrupts = <0 154 0x0>; + interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -261,7 +326,7 @@ i2c@1a280000 { compatible = "qcom,i2c-qup-v1.1.1"; reg = <0x1a280000 0x1000>; - interrupts = <0 155 0>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; clock-names = "core", "iface"; @@ -274,7 +339,7 @@ spi@1a280000 { compatible = "qcom,spi-qup-v1.1.1"; reg = <0x1a280000 0x1000>; - interrupts = <0 155 0>; + interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; clock-names = "core", "iface"; @@ -301,7 +366,7 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16640000 0x1000>, <0x16600000 0x1000>; - interrupts = <0 158 0x0>; + interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>; clock-names = "core", "iface"; status = "disabled"; @@ -323,7 +388,7 @@ compatible = "qcom,ipq806x-ahci", "generic-ahci"; reg = <0x29000000 0x180>; - interrupts = <0 209 0x0>; + interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; clocks = <&gcc SFAB_SATA_S_H_CLK>, <&gcc SATA_H_CLK>, @@ -366,5 +431,233 @@ #reset-cells = <1>; }; + pcie0: pci@1b500000 { + compatible = "qcom,pcie-ipq8064"; + reg = <0x1b500000 0x1000 + 0x1b502000 0x80 + 0x1b600000 0x100 + 0x0ff00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ + 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ + + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc PCIE_A_CLK>, + <&gcc PCIE_H_CLK>, + <&gcc PCIE_PHY_CLK>, + <&gcc PCIE_AUX_CLK>, + <&gcc PCIE_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; + + assigned-clocks = <&gcc PCIE_ALT_REF_CLK>; + assigned-clock-rates = <100000000>; + + resets = <&gcc PCIE_ACLK_RESET>, + <&gcc PCIE_HCLK_RESET>, + <&gcc PCIE_POR_RESET>, + <&gcc PCIE_PCI_RESET>, + <&gcc PCIE_PHY_RESET>, + <&gcc PCIE_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; + + pinctrl-0 = <&pcie0_pins>; + pinctrl-names = "default"; + + status = "disabled"; + perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; + }; + + pcie1: pci@1b700000 { + compatible = "qcom,pcie-ipq8064"; + reg = <0x1b700000 0x1000 + 0x1b702000 0x80 + 0x1b800000 0x100 + 0x31f00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <1>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ + 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc PCIE_1_A_CLK>, + <&gcc PCIE_1_H_CLK>, + <&gcc PCIE_1_PHY_CLK>, + <&gcc PCIE_1_AUX_CLK>, + <&gcc PCIE_1_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; + + assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>; + assigned-clock-rates = <100000000>; + + resets = <&gcc PCIE_1_ACLK_RESET>, + <&gcc PCIE_1_HCLK_RESET>, + <&gcc PCIE_1_POR_RESET>, + <&gcc PCIE_1_PCI_RESET>, + <&gcc PCIE_1_PHY_RESET>, + <&gcc PCIE_1_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; + + pinctrl-0 = <&pcie1_pins>; + pinctrl-names = "default"; + + status = "disabled"; + perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; + }; + + pcie2: pci@1b900000 { + compatible = "qcom,pcie-ipq8064"; + reg = <0x1b900000 0x1000 + 0x1b902000 0x80 + 0x1ba00000 0x100 + 0x35f00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <2>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ + 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ + + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc PCIE_2_A_CLK>, + <&gcc PCIE_2_H_CLK>, + <&gcc PCIE_2_PHY_CLK>, + <&gcc PCIE_2_AUX_CLK>, + <&gcc PCIE_2_ALT_REF_CLK>; + clock-names = "core", "iface", "phy", "aux", "ref"; + + assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>; + assigned-clock-rates = <100000000>; + + resets = <&gcc PCIE_2_ACLK_RESET>, + <&gcc PCIE_2_HCLK_RESET>, + <&gcc PCIE_2_POR_RESET>, + <&gcc PCIE_2_PCI_RESET>, + <&gcc PCIE_2_PHY_RESET>, + <&gcc PCIE_2_EXT_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; + + pinctrl-0 = <&pcie2_pins>; + pinctrl-names = "default"; + + status = "disabled"; + perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; + }; + + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + sdcc1bam:dma@12402000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12402000 0x8000>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC1_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + sdcc3bam:dma@12182000 { + compatible = "qcom,bam-v1.3.0"; + reg = <0x12182000 0x8000>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc SDC3_H_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; + + amba { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + sdcc@12400000 { + status = "disabled"; + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + reg = <0x12400000 0x2000>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + max-frequency = <96000000>; + non-removable; + cap-sd-highspeed; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; + dma-names = "tx", "rx"; + }; + + sdcc@12180000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12180000 0x2000>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <8>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <192000000>; + #mmc-ddr-1_8v; + sd-uhs-sdr104; + sd-uhs-ddr50; + vqmmc-supply = <&vsdcc_fixed>; + dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; + dma-names = "tx", "rx"; + }; + }; }; }; |