diff options
Diffstat (limited to 'arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi')
-rw-r--r-- | arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi | 318 |
1 files changed, 314 insertions, 4 deletions
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi index 1c8f1b86472d..bf20c55a6bc4 100644 --- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi @@ -19,10 +19,38 @@ #include <dt-bindings/input/input.h> #include <dt-bindings/gpio/gpio.h> +/* + * GPIO name legend: proper name = the GPIO line is used as GPIO + * NC = not connected (pin out but not routed from the chip to + * anything the board) + * "[PER]" = pin is muxed for [peripheral] (not GPIO) + * LSEC = Low Speed External Connector + * P HSEC = Primary High Speed External Connector + * S HSEC = Secondary High Speed External Connector + * J14 = Camera Connector + * TP = Test Points + * + * Line names are taken from the schematic "DragonBoard 820c", + * drawing no: LM25-P2751-1 + * + * For the lines routed to the external connectors the + * lines are named after the 96Boards CE Specification 1.0, + * Appendix "Expansion Connector Signal Description". + * + * When the 96Board naming of a line and the schematic name of + * the same line are in conflict, the 96Board specification + * takes precedence, which means that the external UART on the + * LSEC is named UART0 while the schematic and SoC names this + * UART3. This is only for the informational lines i.e. "[FOO]", + * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only + * ones actually used for GPIO. + */ + / { aliases { serial0 = &blsp2_uart1; serial1 = &blsp2_uart2; + serial2 = &blsp1_uart1; i2c0 = &blsp1_i2c2; i2c1 = &blsp2_i2c1; i2c2 = &blsp2_i2c0; @@ -34,7 +62,36 @@ stdout-path = "serial0:115200n8"; }; + clocks { + divclk4: divclk4 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "divclk4"; + + pinctrl-names = "default"; + pinctrl-0 = <&divclk4_pin_a>; + }; + }; + soc { + serial@7570000 { + label = "BT-UART"; + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_uart1_default>; + pinctrl-1 = <&blsp1_uart1_sleep>; + + bluetooth { + compatible = "qcom,qca6174-bt"; + + /* bt_disable_n gpio */ + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + + clocks = <&divclk4>; + }; + }; + serial@75b0000 { label = "LS-UART1"; status = "okay"; @@ -45,7 +102,7 @@ serial@75b1000 { label = "LS-UART0"; - status = "okay"; + status = "disabled"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&blsp2_uart2_4pins_default>; pinctrl-1 = <&blsp2_uart2_4pins_sleep>; @@ -87,9 +144,231 @@ pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; cd-gpios = <&msmgpio 38 0x1>; + vmmc-supply = <&pm8994_l21>; + vqmmc-supply = <&pm8994_l13>; + status = "okay"; + }; + + phy@627000 { status = "okay"; }; + ufshc@624000 { + status = "okay"; + }; + + pinctrl@1010000 { + gpio-line-names = + "[SPI0_DOUT]", /* GPIO_0, BLSP1_SPI_MOSI, LSEC pin 14 */ + "[SPI0_DIN]", /* GPIO_1, BLSP1_SPI_MISO, LSEC pin 10 */ + "[SPI0_CS]", /* GPIO_2, BLSP1_SPI_CS_N, LSEC pin 12 */ + "[SPI0_SCLK]", /* GPIO_3, BLSP1_SPI_CLK, LSEC pin 8 */ + "[UART1_TxD]", /* GPIO_4, BLSP8_UART_TX, LSEC pin 11 */ + "[UART1_RxD]", /* GPIO_5, BLSP8_UART_RX, LSEC pin 13 */ + "[I2C1_SDA]", /* GPIO_6, BLSP8_I2C_SDA, LSEC pin 21 */ + "[I2C1_SCL]", /* GPIO_7, BLSP8_I2C_SCL, LSEC pin 19 */ + "GPIO-H", /* GPIO_8, LCD0_RESET_N, LSEC pin 30 */ + "TP93", /* GPIO_9 */ + "GPIO-G", /* GPIO_10, MDP_VSYNC_P, LSEC pin 29 */ + "[MDP_VSYNC_S]", /* GPIO_11, S HSEC pin 55 */ + "NC", /* GPIO_12 */ + "[CSI0_MCLK]", /* GPIO_13, CAM_MCLK0, P HSEC pin 15 */ + "[CAM_MCLK1]", /* GPIO_14, J14 pin 11 */ + "[CSI1_MCLK]", /* GPIO_15, CAM_MCLK2, P HSEC pin 17 */ + "TP99", /* GPIO_16 */ + "[I2C2_SDA]", /* GPIO_17, CCI_I2C_SDA0, P HSEC pin 34 */ + "[I2C2_SCL]", /* GPIO_18, CCI_I2C_SCL0, P HSEC pin 32 */ + "[CCI_I2C_SDA1]", /* GPIO_19, S HSEC pin 38 */ + "[CCI_I2C_SCL1]", /* GPIO_20, S HSEC pin 36 */ + "FLASH_STROBE_EN", /* GPIO_21, S HSEC pin 5 */ + "FLASH_STROBE_TRIG", /* GPIO_22, S HSEC pin 1 */ + "GPIO-K", /* GPIO_23, CAM2_RST_N, LSEC pin 33 */ + "GPIO-D", /* GPIO_24, LSEC pin 26 */ + "GPIO-I", /* GPIO_25, CAM0_RST_N, LSEC pin 31 */ + "GPIO-J", /* GPIO_26, CAM0_STANDBY_N, LSEC pin 32 */ + "BLSP6_I2C_SDA", /* GPIO_27 */ + "BLSP6_I2C_SCL", /* GPIO_28 */ + "GPIO-B", /* GPIO_29, TS0_RESET_N, LSEC pin 24 */ + "GPIO30", /* GPIO_30, S HSEC pin 4 */ + "HDMI_CEC", /* GPIO_31 */ + "HDMI_DDC_CLOCK", /* GPIO_32 */ + "HDMI_DDC_DATA", /* GPIO_33 */ + "HDMI_HOT_PLUG_DETECT", /* GPIO_34 */ + "PCIE0_RST_N", /* GPIO_35 */ + "PCIE0_CLKREQ_N", /* GPIO_36 */ + "PCIE0_WAKE", /* GPIO_37 */ + "SD_CARD_DET_N", /* GPIO_38 */ + "TSIF1_SYNC", /* GPIO_39, S HSEC pin 48 */ + "W_DISABLE_N", /* GPIO_40 */ + "[BLSP9_UART_TX]", /* GPIO_41 */ + "[BLSP9_UART_RX]", /* GPIO_42 */ + "[BLSP2_UART_CTS_N]", /* GPIO_43 */ + "[BLSP2_UART_RFR_N]", /* GPIO_44 */ + "[BLSP3_UART_TX]", /* GPIO_45 */ + "[BLSP3_UART_RX]", /* GPIO_46 */ + "[I2C0_SDA]", /* GPIO_47, LS_I2C0_SDA, LSEC pin 17 */ + "[I2C0_SCL]", /* GPIO_48, LS_I2C0_SCL, LSEC pin 15 */ + "[UART0_TxD]", /* GPIO_49, BLSP9_UART_TX, LSEC pin 5 */ + "[UART0_RxD]", /* GPIO_50, BLSP9_UART_RX, LSEC pin 7 */ + "[UART0_CTS]", /* GPIO_51, BLSP9_UART_CTS_N, LSEC pin 3 */ + "[UART0_RTS]", /* GPIO_52, BLSP9_UART_RFR_N, LSEC pin 9 */ + "[CODEC_INT1_N]", /* GPIO_53 */ + "[CODEC_INT2_N]", /* GPIO_54 */ + "[BLSP7_I2C_SDA]", /* GPIO_55 */ + "[BLSP7_I2C_SCL]", /* GPIO_56 */ + "MI2S_MCLK", /* GPIO_57, S HSEC pin 3 */ + "[PCM_CLK]", /* GPIO_58, QUA_MI2S_SCK, LSEC pin 18 */ + "[PCM_FS]", /* GPIO_59, QUA_MI2S_WS, LSEC pin 16 */ + "[PCM_DO]", /* GPIO_60, QUA_MI2S_DATA0, LSEC pin 20 */ + "[PCM_DI]", /* GPIO_61, QUA_MI2S_DATA1, LSEC pin 22 */ + "GPIO-E", /* GPIO_62, LSEC pin 27 */ + "TP87", /* GPIO_63 */ + "[CODEC_RST_N]", /* GPIO_64 */ + "[PCM1_CLK]", /* GPIO_65 */ + "[PCM1_SYNC]", /* GPIO_66 */ + "[PCM1_DIN]", /* GPIO_67 */ + "[PCM1_DOUT]", /* GPIO_68 */ + "AUDIO_REF_CLK", /* GPIO_69 */ + "SLIMBUS_CLK", /* GPIO_70 */ + "SLIMBUS_DATA0", /* GPIO_71 */ + "SLIMBUS_DATA1", /* GPIO_72 */ + "NC", /* GPIO_73 */ + "NC", /* GPIO_74 */ + "NC", /* GPIO_75 */ + "NC", /* GPIO_76 */ + "TP94", /* GPIO_77 */ + "NC", /* GPIO_78 */ + "TP95", /* GPIO_79 */ + "GPIO-A", /* GPIO_80, MEMS_RESET_N, LSEC pin 23 */ + "TP88", /* GPIO_81 */ + "TP89", /* GPIO_82 */ + "TP90", /* GPIO_83 */ + "TP91", /* GPIO_84 */ + "[SD_DAT0]", /* GPIO_85, BLSP12_SPI_MOSI, P HSEC pin 1 */ + "[SD_CMD]", /* GPIO_86, BLSP12_SPI_MISO, P HSEC pin 11 */ + "[SD_DAT3]", /* GPIO_87, BLSP12_SPI_CS_N, P HSEC pin 7 */ + "[SD_SCLK]", /* GPIO_88, BLSP12_SPI_CLK, P HSEC pin 9 */ + "TSIF1_CLK", /* GPIO_89, S HSEC pin 42 */ + "TSIF1_EN", /* GPIO_90, S HSEC pin 46 */ + "TSIF1_DATA", /* GPIO_91, S HSEC pin 44 */ + "NC", /* GPIO_92 */ + "TSIF2_CLK", /* GPIO_93, S HSEC pin 52 */ + "TSIF2_EN", /* GPIO_94, S HSEC pin 56 */ + "TSIF2_DATA", /* GPIO_95, S HSEC pin 54 */ + "TSIF2_SYNC", /* GPIO_96, S HSEC pin 58 */ + "NC", /* GPIO_97 */ + "CAM1_STANDBY_N", /* GPIO_98 */ + "NC", /* GPIO_99 */ + "NC", /* GPIO_100 */ + "[LCD1_RESET_N]", /* GPIO_101, S HSEC pin 51 */ + "BOOT_CONFIG1", /* GPIO_102 */ + "USB_HUB_RESET", /* GPIO_103 */ + "CAM1_RST_N", /* GPIO_104 */ + "NC", /* GPIO_105 */ + "NC", /* GPIO_106 */ + "NC", /* GPIO_107 */ + "NC", /* GPIO_108 */ + "NC", /* GPIO_109 */ + "NC", /* GPIO_110 */ + "NC", /* GPIO_111 */ + "NC", /* GPIO_112 */ + "PMI8994_BUA", /* GPIO_113 */ + "PCIE2_RST_N", /* GPIO_114 */ + "PCIE2_CLKREQ_N", /* GPIO_115 */ + "PCIE2_WAKE", /* GPIO_116 */ + "SSC_IRQ_0", /* GPIO_117 */ + "SSC_IRQ_1", /* GPIO_118 */ + "SSC_IRQ_2", /* GPIO_119 */ + "NC", /* GPIO_120 */ + "GPIO121", /* GPIO_121, S HSEC pin 2 */ + "NC", /* GPIO_122 */ + "SSC_IRQ_6", /* GPIO_123 */ + "SSC_IRQ_7", /* GPIO_124 */ + "GPIO-C", /* GPIO_125, TS_INT0, LSEC pin 25 */ + "BOOT_CONFIG5", /* GPIO_126 */ + "NC", /* GPIO_127 */ + "NC", /* GPIO_128 */ + "BOOT_CONFIG7", /* GPIO_129 */ + "PCIE1_RST_N", /* GPIO_130 */ + "PCIE1_CLKREQ_N", /* GPIO_131 */ + "PCIE1_WAKE", /* GPIO_132 */ + "GPIO-L", /* GPIO_133, CAM2_STANDBY_N, LSEC pin 34 */ + "NC", /* GPIO_134 */ + "NC", /* GPIO_135 */ + "BOOT_CONFIG8", /* GPIO_136 */ + "NC", /* GPIO_137 */ + "NC", /* GPIO_138 */ + "GPS_SSBI2", /* GPIO_139 */ + "GPS_SSBI1", /* GPIO_140 */ + "NC", /* GPIO_141 */ + "NC", /* GPIO_142 */ + "NC", /* GPIO_143 */ + "BOOT_CONFIG6", /* GPIO_144 */ + "NC", /* GPIO_145 */ + "NC", /* GPIO_146 */ + "NC", /* GPIO_147 */ + "NC", /* GPIO_148 */ + "NC"; /* GPIO_149 */ + }; + + qcom,spmi@400f000 { + pmic@0 { + gpios@c000 { + gpio-line-names = + "NC", + "KEY_VOLP_N", + "NC", + "BL1_PWM", + "GPIO-F", /* BL0_PWM, LSEC pin 28 */ + "BL1_EN", + "NC", + "WLAN_EN", + "NC", + "NC", + "NC", + "NC", + "NC", + "NC", + "DIVCLK1", + "DIVCLK2", + "DIVCLK3", + "DIVCLK4", + "BT_EN", + "PMIC_SLB", + "PMIC_BUA", + "USB_VBUS_DET"; + }; + + mpps@a000 { + gpio-line-names = + "VDDPX_BIAS", + "WIFI_LED", + "NC", + "BT_LED", + "PM_MPP05", + "PM_MPP06", + "PM_MPP07", + "NC"; + }; + }; + + pmic@2 { + gpios@c000 { + gpio-line-names = + "NC", + "SPKR_AMP_EN1", + "SPKR_AMP_EN2", + "TP61", + "NC", + "USB2_VBUS_DET", + "NC", + "NC", + "NC", + "NC"; + }; + }; + }; + phy@34000 { status = "okay"; }; @@ -139,17 +418,34 @@ pinctrl-0 = <&usb2_vbus_det_gpio>; }; + wlan_en: wlan-en-1-8v { + pinctrl-names = "default"; + pinctrl-0 = <&wlan_en_gpios>; + compatible = "regulator-fixed"; + regulator-name = "wlan-en-regulator"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&pm8994_gpios 8 0>; + + /* WLAN card specific delay */ + startup-delay-us = <70000>; + enable-active-high; + }; + agnoc@0 { - qcom,pcie@600000 { + pcie@600000 { + status = "okay"; perst-gpio = <&msmgpio 35 GPIO_ACTIVE_LOW>; + vddpe-3v3-supply = <&wlan_en>; }; - qcom,pcie@608000 { + pcie@608000 { status = "okay"; perst-gpio = <&msmgpio 130 GPIO_ACTIVE_LOW>; }; - qcom,pcie@610000 { + pcie@610000 { status = "okay"; perst-gpio = <&msmgpio 114 GPIO_ACTIVE_LOW>; }; @@ -327,3 +623,17 @@ }; }; }; + +&spmi_bus { + pmic@0 { + pon@800 { + resin { + compatible = "qcom,pm8941-resin"; + interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + }; +}; |