diff options
Diffstat (limited to 'drivers/mtd/spi-nor/spansion.c')
| -rw-r--r-- | drivers/mtd/spi-nor/spansion.c | 185 |
1 files changed, 163 insertions, 22 deletions
diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c index 43cd6cd92537..0150049007be 100644 --- a/drivers/mtd/spi-nor/spansion.c +++ b/drivers/mtd/spi-nor/spansion.c @@ -14,6 +14,8 @@ #define SPINOR_OP_CLSR 0x30 /* Clear status register 1 */ #define SPINOR_OP_RD_ANY_REG 0x65 /* Read any register */ #define SPINOR_OP_WR_ANY_REG 0x71 /* Write any register */ +#define SPINOR_REG_CYPRESS_CFR1V 0x00800002 +#define SPINOR_REG_CYPRESS_CFR1V_QUAD_EN BIT(1) /* Quad Enable */ #define SPINOR_REG_CYPRESS_CFR2V 0x00800003 #define SPINOR_REG_CYPRESS_CFR2V_MEMLAT_11_24 0xb #define SPINOR_REG_CYPRESS_CFR3V 0x00800004 @@ -114,6 +116,150 @@ static int cypress_nor_octal_dtr_dis(struct spi_nor *nor) } /** + * cypress_nor_quad_enable_volatile() - enable Quad I/O mode in volatile + * register. + * @nor: pointer to a 'struct spi_nor' + * + * It is recommended to update volatile registers in the field application due + * to a risk of the non-volatile registers corruption by power interrupt. This + * function sets Quad Enable bit in CFR1 volatile. If users set the Quad Enable + * bit in the CFR1 non-volatile in advance (typically by a Flash programmer + * before mounting Flash on PCB), the Quad Enable bit in the CFR1 volatile is + * also set during Flash power-up. + * + * Return: 0 on success, -errno otherwise. + */ +static int cypress_nor_quad_enable_volatile(struct spi_nor *nor) +{ + struct spi_mem_op op; + u8 addr_mode_nbytes = nor->params->addr_mode_nbytes; + u8 cfr1v_written; + int ret; + + op = (struct spi_mem_op) + CYPRESS_NOR_RD_ANY_REG_OP(addr_mode_nbytes, + SPINOR_REG_CYPRESS_CFR1V, + nor->bouncebuf); + + ret = spi_nor_read_any_reg(nor, &op, nor->reg_proto); + if (ret) + return ret; + + if (nor->bouncebuf[0] & SPINOR_REG_CYPRESS_CFR1V_QUAD_EN) + return 0; + + /* Update the Quad Enable bit. */ + nor->bouncebuf[0] |= SPINOR_REG_CYPRESS_CFR1V_QUAD_EN; + op = (struct spi_mem_op) + CYPRESS_NOR_WR_ANY_REG_OP(addr_mode_nbytes, + SPINOR_REG_CYPRESS_CFR1V, 1, + nor->bouncebuf); + ret = spi_nor_write_any_volatile_reg(nor, &op, nor->reg_proto); + if (ret) + return ret; + + cfr1v_written = nor->bouncebuf[0]; + + /* Read back and check it. */ + op = (struct spi_mem_op) + CYPRESS_NOR_RD_ANY_REG_OP(addr_mode_nbytes, + SPINOR_REG_CYPRESS_CFR1V, + nor->bouncebuf); + ret = spi_nor_read_any_reg(nor, &op, nor->reg_proto); + if (ret) + return ret; + + if (nor->bouncebuf[0] != cfr1v_written) { + dev_err(nor->dev, "CFR1: Read back test failed\n"); + return -EIO; + } + + return 0; +} + +/** + * cypress_nor_set_page_size() - Set page size which corresponds to the flash + * configuration. + * @nor: pointer to a 'struct spi_nor' + * + * The BFPT table advertises a 512B or 256B page size depending on part but the + * page size is actually configurable (with the default being 256B). Read from + * CFR3V[4] and set the correct size. + * + * Return: 0 on success, -errno otherwise. + */ +static int cypress_nor_set_page_size(struct spi_nor *nor) +{ + struct spi_mem_op op = + CYPRESS_NOR_RD_ANY_REG_OP(3, SPINOR_REG_CYPRESS_CFR3V, + nor->bouncebuf); + int ret; + + ret = spi_nor_read_any_reg(nor, &op, nor->reg_proto); + if (ret) + return ret; + + if (nor->bouncebuf[0] & SPINOR_REG_CYPRESS_CFR3V_PGSZ) + nor->params->page_size = 512; + else + nor->params->page_size = 256; + + return 0; +} + +static int +s25hx_t_post_bfpt_fixup(struct spi_nor *nor, + const struct sfdp_parameter_header *bfpt_header, + const struct sfdp_bfpt *bfpt) +{ + /* Replace Quad Enable with volatile version */ + nor->params->quad_enable = cypress_nor_quad_enable_volatile; + + return cypress_nor_set_page_size(nor); +} + +static void s25hx_t_post_sfdp_fixup(struct spi_nor *nor) +{ + struct spi_nor_erase_type *erase_type = + nor->params->erase_map.erase_type; + unsigned int i; + + /* + * In some parts, 3byte erase opcodes are advertised by 4BAIT. + * Convert them to 4byte erase opcodes. + */ + for (i = 0; i < SNOR_ERASE_TYPE_MAX; i++) { + switch (erase_type[i].opcode) { + case SPINOR_OP_SE: + erase_type[i].opcode = SPINOR_OP_SE_4B; + break; + case SPINOR_OP_BE_4K: + erase_type[i].opcode = SPINOR_OP_BE_4K_4B; + break; + default: + break; + } + } +} + +static void s25hx_t_late_init(struct spi_nor *nor) +{ + struct spi_nor_flash_parameter *params = nor->params; + + /* Fast Read 4B requires mode cycles */ + params->reads[SNOR_CMD_READ_FAST].num_mode_clocks = 8; + + /* The writesize should be ECC data unit size */ + params->writesize = 16; +} + +static struct spi_nor_fixups s25hx_t_fixups = { + .post_bfpt = s25hx_t_post_bfpt_fixup, + .post_sfdp = s25hx_t_post_sfdp_fixup, + .late_init = s25hx_t_late_init, +}; + +/** * cypress_nor_octal_dtr_enable() - Enable octal DTR on Cypress flashes. * @nor: pointer to a 'struct spi_nor' * @enable: whether to enable or disable Octal DTR @@ -167,28 +313,7 @@ static int s28hs512t_post_bfpt_fixup(struct spi_nor *nor, const struct sfdp_parameter_header *bfpt_header, const struct sfdp_bfpt *bfpt) { - /* - * The BFPT table advertises a 512B page size but the page size is - * actually configurable (with the default being 256B). Read from - * CFR3V[4] and set the correct size. - */ - struct spi_mem_op op = - CYPRESS_NOR_RD_ANY_REG_OP(3, SPINOR_REG_CYPRESS_CFR3V, - nor->bouncebuf); - int ret; - - spi_nor_spimem_setup_op(nor, &op, nor->reg_proto); - - ret = spi_mem_exec_op(nor->spimem, &op); - if (ret) - return ret; - - if (nor->bouncebuf[0] & SPINOR_REG_CYPRESS_CFR3V_PGSZ) - nor->params->page_size = 512; - else - nor->params->page_size = 256; - - return 0; + return cypress_nor_set_page_size(nor); } static const struct spi_nor_fixups s28hs512t_fixups = { @@ -310,6 +435,22 @@ static const struct flash_info spansion_nor_parts[] = { { "s25fl256l", INFO(0x016019, 0, 64 * 1024, 512) NO_SFDP_FLAGS(SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) FIXUP_FLAGS(SPI_NOR_4B_OPCODES) }, + { "s25hl512t", INFO6(0x342a1a, 0x0f0390, 256 * 1024, 256) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, + { "s25hl01gt", INFO6(0x342a1b, 0x0f0390, 256 * 1024, 512) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, + { "s25hs512t", INFO6(0x342b1a, 0x0f0390, 256 * 1024, 256) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, + { "s25hs01gt", INFO6(0x342b1b, 0x0f0390, 256 * 1024, 512) + PARSE_SFDP + MFR_FLAGS(USE_CLSR) + .fixups = &s25hx_t_fixups }, { "cy15x104q", INFO6(0x042cc2, 0x7f7f7f, 512 * 1024, 1) FLAGS(SPI_NOR_NO_ERASE) }, { "s28hs512t", INFO(0x345b1a, 0, 256 * 1024, 256) |