diff options
Diffstat (limited to 'drivers/phy/ti/phy-twl4030-usb.c')
| -rw-r--r-- | drivers/phy/ti/phy-twl4030-usb.c | 50 |
1 files changed, 14 insertions, 36 deletions
diff --git a/drivers/phy/ti/phy-twl4030-usb.c b/drivers/phy/ti/phy-twl4030-usb.c index c267afb68f07..9887f908f540 100644 --- a/drivers/phy/ti/phy-twl4030-usb.c +++ b/drivers/phy/ti/phy-twl4030-usb.c @@ -1,3 +1,4 @@ +// SPDX-License-Identifier: GPL-2.0-or-later /* * twl4030_usb - TWL4030 USB transceiver, talking to OMAP OTG controller * @@ -5,20 +6,6 @@ * Copyright (C) 2008 Nokia Corporation * Contact: Felipe Balbi <felipe.balbi@nokia.com> * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * * Current status: * - HS USB ULPI mode works. * - 3-pin mode support may be added in future. @@ -172,6 +159,7 @@ struct twl4030_usb { int irq; enum musb_vbus_id_status linkstat; + atomic_t connected; bool vbus_supplied; bool musb_mailbox_pending; @@ -575,39 +563,29 @@ static irqreturn_t twl4030_usb_irq(int irq, void *_twl) { struct twl4030_usb *twl = _twl; enum musb_vbus_id_status status; - bool status_changed = false; int err; status = twl4030_usb_linkstat(twl); mutex_lock(&twl->lock); - if (status >= 0 && status != twl->linkstat) { - status_changed = - cable_present(twl->linkstat) != - cable_present(status); - twl->linkstat = status; - } + twl->linkstat = status; mutex_unlock(&twl->lock); - if (status_changed) { - /* FIXME add a set_power() method so that B-devices can - * configure the charger appropriately. It's not always - * correct to consume VBUS power, and how much current to - * consume is a function of the USB configuration chosen - * by the host. - * - * REVISIT usb_gadget_vbus_connect(...) as needed, ditto - * its disconnect() sibling, when changing to/from the - * USB_LINK_VBUS state. musb_hdrc won't care until it - * starts to handle softconnect right. - */ - if (cable_present(status)) { + if (cable_present(status)) { + if (atomic_add_unless(&twl->connected, 1, 1)) { + dev_dbg(twl->dev, "%s: cable connected %i\n", + __func__, status); pm_runtime_get_sync(twl->dev); - } else { + twl->musb_mailbox_pending = true; + } + } else { + if (atomic_add_unless(&twl->connected, -1, 0)) { + dev_dbg(twl->dev, "%s: cable disconnected %i\n", + __func__, status); pm_runtime_mark_last_busy(twl->dev); pm_runtime_put_autosuspend(twl->dev); + twl->musb_mailbox_pending = true; } - twl->musb_mailbox_pending = true; } if (twl->musb_mailbox_pending) { err = musb_mailbox(status); |