diff options
Diffstat (limited to 'include/uapi/linux/nl80211.h')
| -rw-r--r-- | include/uapi/linux/nl80211.h | 59 |
1 files changed, 57 insertions, 2 deletions
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h index f14621a954e1..c59fec406da5 100644 --- a/include/uapi/linux/nl80211.h +++ b/include/uapi/linux/nl80211.h @@ -1299,6 +1299,16 @@ * @NL80211_CMD_MODIFY_LINK_STA: Modify a link of an MLD station * @NL80211_CMD_REMOVE_LINK_STA: Remove a link of an MLD station * + * @NL80211_CMD_SET_HW_TIMESTAMP: Enable/disable HW timestamping of Timing + * measurement and Fine timing measurement frames. If %NL80211_ATTR_MAC + * is included, enable/disable HW timestamping only for frames to/from the + * specified MAC address. Otherwise enable/disable HW timestamping for + * all TM/FTM frames (including ones that were enabled with specific MAC + * address). If %NL80211_ATTR_HW_TIMESTAMP_ENABLED is not included, disable + * HW timestamping. + * The number of peers that HW timestamping can be enabled for concurrently + * is indicated by %NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS. + * * @NL80211_CMD_MAX: highest used command number * @__NL80211_CMD_AFTER_LAST: internal use */ @@ -1550,6 +1560,8 @@ enum nl80211_commands { NL80211_CMD_MODIFY_LINK_STA, NL80211_CMD_REMOVE_LINK_STA, + NL80211_CMD_SET_HW_TIMESTAMP, + /* add new commands above here */ /* used to define NL80211_CMD_MAX below */ @@ -2775,6 +2787,24 @@ enum nl80211_commands { * indicates that the sub-channel is punctured. Higher 16 bits are * reserved. * + * @NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS: Maximum number of peers that HW + * timestamping can be enabled for concurrently (u16), a wiphy attribute. + * A value of 0xffff indicates setting for all peers (i.e. not specifying + * an address with %NL80211_CMD_SET_HW_TIMESTAMP) is supported. + * @NL80211_ATTR_HW_TIMESTAMP_ENABLED: Indicates whether HW timestamping should + * be enabled or not (flag attribute). + * + * @NL80211_ATTR_EMA_RNR_ELEMS: Optional nested attribute for + * reduced neighbor report (RNR) elements. This attribute can be used + * only when NL80211_MBSSID_CONFIG_ATTR_EMA is enabled. + * Userspace is responsible for splitting the RNR into multiple + * elements such that each element excludes the non-transmitting + * profiles already included in the MBSSID element + * (%NL80211_ATTR_MBSSID_ELEMS) at the same index. Each EMA beacon + * will be generated by adding MBSSID and RNR elements at the same + * index. If the userspace includes more RNR elements than number of + * MBSSID elements then these will be added in every EMA beacon. + * * @NUM_NL80211_ATTR: total number of nl80211_attrs available * @NL80211_ATTR_MAX: highest attribute number currently defined * @__NL80211_ATTR_AFTER_LAST: internal use @@ -3306,6 +3336,11 @@ enum nl80211_attrs { NL80211_ATTR_PUNCT_BITMAP, + NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS, + NL80211_ATTR_HW_TIMESTAMP_ENABLED, + + NL80211_ATTR_EMA_RNR_ELEMS, + /* add attributes here, update the policy in nl80211.c */ __NL80211_ATTR_AFTER_LAST, @@ -4026,6 +4061,10 @@ enum nl80211_band_iftype_attr { * @NL80211_BAND_ATTR_EDMG_BW_CONFIG: Channel BW Configuration subfield encodes * the allowed channel bandwidth configurations. * Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13. + * @NL80211_BAND_ATTR_S1G_MCS_NSS_SET: S1G capabilities, supported S1G-MCS and NSS + * set subfield, as in the S1G information IE, 5 bytes + * @NL80211_BAND_ATTR_S1G_CAPA: S1G capabilities information subfield as in the + * S1G information IE, 10 bytes * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined * @__NL80211_BAND_ATTR_AFTER_LAST: internal use */ @@ -4046,6 +4085,9 @@ enum nl80211_band_attr { NL80211_BAND_ATTR_EDMG_CHANNELS, NL80211_BAND_ATTR_EDMG_BW_CONFIG, + NL80211_BAND_ATTR_S1G_MCS_NSS_SET, + NL80211_BAND_ATTR_S1G_CAPA, + /* keep last */ __NL80211_BAND_ATTR_AFTER_LAST, NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1 @@ -6326,6 +6368,10 @@ enum nl80211_feature_flags { * @NL80211_EXT_FEATURE_SECURE_NAN: Device supports NAN Pairing which enables * authentication, data encryption and message integrity. * + * @NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA: Device supports randomized TA + * in authentication and deauthentication frames sent to unassociated peer + * using @NL80211_CMD_FRAME. + * * @NUM_NL80211_EXT_FEATURES: number of extended features. * @MAX_NL80211_EXT_FEATURES: highest extended feature index. */ @@ -6396,6 +6442,7 @@ enum nl80211_ext_feature_index { NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE, NL80211_EXT_FEATURE_PUNCT, NL80211_EXT_FEATURE_SECURE_NAN, + NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA, /* add new features before the definition below */ NUM_NL80211_EXT_FEATURES, @@ -6510,8 +6557,16 @@ enum nl80211_timeout_reason { * @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with * %NL80211_ATTR_SCAN_FREQ_KHZ. This also means * %NL80211_ATTR_SCAN_FREQUENCIES will not be included. - * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for colocated APs reported by - * 2.4/5 GHz APs + * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for collocated APs reported by + * 2.4/5 GHz APs. When the flag is set, the scan logic will use the + * information from the RNR element found in beacons/probe responses + * received on the 2.4/5 GHz channels to actively scan only the 6GHz + * channels on which APs are expected to be found. Note that when not set, + * the scan logic would scan all 6GHz channels, but since transmission of + * probe requests on non PSC channels is limited, it is highly likely that + * these channels would passively be scanned. Also note that when the flag + * is set, in addition to the colocated APs, PSC channels would also be + * scanned if the user space has asked for it. */ enum nl80211_scan_flags { NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0, |