| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The WRB header is setup by wrb_fill_hdr() routine. This routine currently
gets some of the WRB params as args and figures out rest of the WRB params
by looking at various fields in skb (like gso, checksum, vlan-tag etc).
All these params could instead be retrieved from the skb into a structure
and passed to this routine. This separates wrb_fill_hdr() to only provide
chip-specific code to fill the WRB. This also makes it simple to support
chips with different WRB formats.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Andrew Lunn says:
====================
Indirect phy access for mv88e6171
These two patches allow the mv88e6171 driver to access the port phys
using indirect addressing. Depending on pin strapping, the switch
either uses a single address on the host MDIO bus, requiring the port
phys are accessed indirectly, or the switch uses a number of addresses
on the host bus and the phys can be directly accessed.
The 370RD, the first supported platform to use the 6171 uses multiple
addresses, so this indirect mode was not required. However the
WRT1900AC has the switch configured to use a single address, and so
indirect access is needed.
The mv88e6352 already has all the needed code. Refactor it into the
shared mv88e6xxx and then use it in the mv88e6171 driver.
Tested on the 370RD and WRT1900AC.
It would be good if Guenter Roeck could test on his platform to ensure
i've not broken anything for the mv88e6352.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the device is configured to use single chip addressing mode, the
phy devices of the port are not accessible on the host MDIO
bus. Instead the switch internal MDIO bus must be used. For this to
work, the phy polling unit must be enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mv88e6352 allows access to the port phys via an internal mdio bus
which is accessed using registers in the GLOBAL 2 range. The mv88e6171
and probably other devices use the same mechanism. Move this code into
the shared mv88e6xxx.c library.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This debug output is not really an error message since mac reset can fail
if the phy clocks are gated, specifically when the phy has been placed in
a powered down or isolation mode. The netdev output masks were changed from
err to dbg, and comments added in the code.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change use of Altera TSE's MDIO access from phy 0 registers to phy 1
registers. This allows support for GMII, MII, RGMII, and SGMII
designs where the external PHY is always accesible through
Altera TSE's MDIO phy 1 registers and Altera's PCS is accessible
through MDIO phy 0 registers for SGMII applications.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Tested-by: Kai Lin Ng <kailng@altera.com>
Tested-by: Dalon Westergreen <dwesterg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hayes Wang says:
====================
Adjust the settings about USB_RX_EARLY_AGG
v2:
For patch #1, replace
u32 ocp_data;
ocp_data = tp->coalesce / 8;
with
u32 ocp_data = tp->coalesce / 8;
And replace
struct net_device *dev = tp->netdev;
u32 ocp_data;
ocp_data = (agg_buf_sz - dev->mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;
with
u32 mtu = tp->netdev->mtu;
u32 ocp_data = (agg_buf_sz - mtu - VLAN_ETH_HLEN - VLAN_HLEN) / 4;
Use *switch* statement to replace the checking of *if*.
v1:
The USB_RX_EARLY_AGG contains timeout and size. Separate them, and
they could be set independently. Then, the ethtool could be used to
change the timeout according to situation of the platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support setting the rx coalesce. Then someone could change the rx
agg timeout value through ethtool.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rx early size is calculated with the mtu, so it has to be
re-calculated when the mtu is changed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Separate USB_RX_EARLY_AGG into USB_RX_EARLY_TIMEOUT and USB_RX_EARLY_SIZE.
Replace r8153_set_rx_agg() with r8153_set_rx_early_timeout() and
r8153_set_rx_early_size().
Set the default timeout value according to the USB speed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
|
|
Pull md bugfixes from Neil Brown:
"Three bug md fixes for 3.20
yet-another-livelock in raid5, and a problem with write errors to
4K-block devices"
* tag 'md/3.20-fixes' of git://neil.brown.name/md:
md/raid5: Fix livelock when array is both resyncing and degraded.
md/raid10: round up to bdev_logical_block_size in narrow_write_error.
md/raid1: round up to bdev_logical_block_size in narrow_write_error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull mcelog regression fix from Tony Luck:
"Fix regression - functions on the mce notifier chain should not be
able to decide that an event should not be logged"
* tag 'please-pull-fixmcelog' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Fix regression. All error records should report via /dev/mcelog
|
|
Pull DocBook build fix from Jonathan Corbet:
"Fix the DocBook build failure caused by the move of the i2o subsystem
to the staging tree"
* tag 'docs-fix' of git://git.lwn.net/linux-2.6:
Fix docs build failure caused by i2o removal
|
|
Pull nfsd bugfixes from Bruce Fields:
"These are fixes for two bugs introduced during the merge window"
* 'for-3.20' of git://linux-nfs.org/~bfields/linux:
nfsd4: fix v3-less build
nfsd: fix comparison in fh_fsid_match()
|
|
Commit a7854487cd7128a30a7f4f5259de9f67d5efb95f:
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
Causes an RCW cycle to be forced even when the array is degraded.
A degraded array cannot support RCW as that requires reading all data
blocks, and one may be missing.
Forcing an RCW when it is not possible causes a live-lock and the code
spins, repeatedly deciding to do something that cannot succeed.
So change the condition to only force RCW on non-degraded arrays.
Reported-by: Manibalan P <pmanibalan@amiindia.co.in>
Bisected-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fixes: a7854487cd7128a30a7f4f5259de9f67d5efb95f
Cc: stable@vger.kernel.org (v3.7+)
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull lazytime mount option support from Al Viro:
"Lazytime stuff from tytso"
* 'lazytime' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ext4: add optimization for the lazytime mount option
vfs: add find_inode_nowait() function
vfs: add support for a lazytime mount option
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull iov_iter updates from Al Viro:
"More iov_iter work - missing counterpart of iov_iter_init() for
bvec-backed ones and vfs_read_iter()/vfs_write_iter() - wrappers for
sync calls of ->read_iter()/->write_iter()"
* 'iov_iter' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: add vfs_iter_{read,write} helpers
new helper: iov_iter_bvec()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull getname/putname updates from Al Viro:
"Rework of getname/getname_kernel/etc., mostly from Paul Moore. Gets
rid of quite a pile of kludges between namei and audit..."
* 'getname2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
audit: replace getname()/putname() hacks with reference counters
audit: fix filename matching in __audit_inode() and __audit_inode_child()
audit: enable filename recording via getname_kernel()
simpler calling conventions for filename_mountpoint()
fs: create proper filename objects using getname_kernel()
fs: rework getname_kernel to handle up to PATH_MAX sized filenames
cut down the number of do_path_lookup() callers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull misc VFS updates from Al Viro:
"This cycle a lot of stuff sits on topical branches, so I'll be sending
more or less one pull request per branch.
This is the first pile; more to follow in a few. In this one are
several misc commits from early in the cycle (before I went for
separate branches), plus the rework of mntput/dput ordering on umount,
switching to use of fs_pin instead of convoluted games in
namespace_unlock()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch the IO-triggering parts of umount to fs_pin
new fs_pin killing logics
allow attaching fs_pin to a group not associated with some superblock
get rid of the second argument of acct_kill()
take count and rcu_head out of fs_pin
dcache: let the dentry count go down to zero without taking d_lock
pull bumping refcount into ->kill()
kill pin_put()
mode_t whack-a-mole: chelsio
file->f_path.dentry is pinned down for as long as the file is open...
get rid of lustre_dump_dentry()
gut proc_register() a bit
kill d_validate()
ncpfs: get rid of d_validate() nonsense
selinuxfs: don't open-code d_genocide()
|
|
Merge yet more updates from Andrew Morton:
- a pile of minor fs fixes and cleanups
- kexec updates
- random misc fixes in various places: vmcore, rbtree, eventfd, ipc, seccomp.
- a series of python-based kgdb helper scripts
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
seccomp: cap SECCOMP_RET_ERRNO data to MAX_ERRNO
samples/seccomp: improve label helper
ipc,sem: use current->state helpers
scripts/gdb: disable pagination while printing from breakpoint handler
scripts/gdb: define maintainer
scripts/gdb: convert CpuList to generator function
scripts/gdb: convert ModuleList to generator function
scripts/gdb: use a generator instead of iterator for task list
scripts/gdb: ignore byte-compiled python files
scripts/gdb: port to python3 / gdb7.7
scripts/gdb: add basic documentation
scripts/gdb: add lx-lsmod command
scripts/gdb: add class to iterate over CPU masks
scripts/gdb: add lx_current convenience function
scripts/gdb: add internal helper and convenience function for per-cpu lookup
scripts/gdb: add get_gdbserver_type helper
scripts/gdb: add internal helper and convenience function to retrieve thread_info
scripts/gdb: add is_target_arch helper
scripts/gdb: add helper and convenience function to look up tasks
scripts/gdb: add task iteration class
...
|
|
The value resulting from the SECCOMP_RET_DATA mask could exceed MAX_ERRNO
when setting errno during a SECCOMP_RET_ERRNO filter action. This makes
sure we have a reliable value being set, so that an invalid errno will not
be ignored by userspace.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will Drewry <wad@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes a potential corruption with uninitialized stack memory in the
seccomp BPF sample program.
[akpm@linux-foundation.org: coding-style fixlet]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Robert Swiecki <swiecki@google.com>
Tested-by: Robert Swiecki <swiecki@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Call __set_current_state() instead of assigning the new state directly.
These interfaces also aid CONFIG_DEBUG_ATOMIC_SLEEP environments, keeping
track of who changed the state.
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While reporting the (refreshed) list of modules on automatic updates we
may hit the page boundary of the output console and cause a stop if
pagination is enabled. However, gdb does not accept user input while
running over the breakpoint handler. So we get stuck, and the user is
forced to interrupt gdb.
Resolve this by disabling pagination during automatic symbol updates. We
restore the user's configuration once done.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'm proposing myself for keeping an eye on these scripts and integrating
contributions.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Yet another code simplification.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Analogously to the task list, convert the module list to a generator
function. It noticeably simplifies the code.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The iterator does not return any task_struct from the thread_group list
because the first condition in the 'if not t or ...' will only be the
first time None.
Instead of keeping track of the state ourself in the next() function, we
fall back using Python's generator.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Using the gdb scripts leaves byte-compiled python files in the scripts/
directory. These should be ignored by git.
[jan.kiszka@siemens.com: drop redundant mrproper rule as suggested by Michal]
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I tried to use these scripts in an ubuntu 14.04 host (gdb 7.7 compiled
against python 3.3) but there were several errors.
I believe this patch fixes these issues so that the commands now work (I
tested lx-symbols, lx-dmesg, lx-lsmod).
Main issues that needed to be resolved:
* In python 2 iterators have a "next()" method. In python 3 it is
__next__() instead (so let's just add both).
* In older python versions there was an implicit conversion
in object.__format__() (used when an object is in string.format())
where it was converting the object to str first and then
calling str's __format__(). This has now been removed so
we must explicitly convert to str the objects for which
we need to keep this behavior.
* In dmesg.py: in python 3 log_buf is now a "memoryview" object
which needs to be converted to a string in order to use string
methods like "splitlines()". Luckily memoryview exists in
python 2.7.6 as well, so we can convert log_buf to memoryview
and use the same code in both python 2 and python 3.
This version of the patch has now been tested with gdb 7.7 and both python
3.4 and python 2.7.6 (I think asking for at least python 2.7.6 is a
reasonable requirement instead of complicating the code with version
checks etc).
Signed-off-by: Pantelis Koukousoulas <pktoss@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Rob Landley <rob@landley.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds a lsmod-like command to list all currently loaded modules of the
target.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Will be used first to count module references. It is optimized to read
the mask only once per stop.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a shorthand for *$lx_per_cpu("current_task"), i.e. a convenience
function to retrieve the currently running task of the active context.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This function allows to obtain a per-cpu variable, either of the current
or an explicitly specified CPU.
Note: sparc64 version is untested.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This helper probes the type of the gdb server. Supported are QEMU and
KGDB so far. Knowledge about the gdb server is required e.g. to
retrieve the current CPU or current task.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
thread_info
Add the internal helper get_thread_info that calculates the thread_info
from a given task variable. Also export this service as a convenience
function.
Note: ia64 version is untested.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This helper caches to result of "show architecture" and matches the
provided arch (sub-)string against that output.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the helper task_by_pid that can look up a task by its PID. Also
export it as a convenience function.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This class allows to iterate over all tasks of the target.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This pokes into the log buffer of the debugged kernel, dumping it to the
gdb console. Helping in case the target should or can no longer execute
dmesg itself.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add helpers for reading integers from target memory buffers. Required
when caching the memory access is more efficient than reading individual
values via gdb.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Parse the target endianness from the output of "show endian" and cache the
result to return it via the new helper get_target_endiannes. We will need
it for reading integers from buffers that contain target memory.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add the internal helper get_module_by_name to obtain the module structure
corresponding to the given name. Also export this service as a
convenience function.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This installs a silent breakpoint on the do_init_module function. The
breakpoint handler will try to load symbols from the module files found
during lx-symbols execution. This way, breakpoints can be set to module
initialization functions, and there is no need to explicitly call
lx-symbols after (re-)loading a module.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This provides a reliable breakpoint target, required for automatic symbol
loading via the gdb helper command 'lx-symbols'.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is probably the most useful helper when debugging kernel modules:
lx-symbols first reloads vmlinux. Then it searches recursively for *.ko
files in the specified paths and the current directory. Finally it walks
the kernel's module list, issuing the necessary add-symbol-file command
for each loaded module so that gdb knows which module symbol corresponds
to which address. It also looks up variable sections (bss, data, rodata)
and appends their address to the add-symbole-file command line. This
allows to access global module variables just like any other variable.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
