| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
CPUIDLE_FLAG_TIME_INVALID is no longer checked
by menu or ladder cpuidle governors, so don't
bother setting or defining it.
It was originally invented to account for the fact that
acpi_safe_halt() enables interrupts to invoke HLT.
That would allow interrupt service routines to be included
in the last_idle duration measurements made in cpuidle_enter_state(),
potentially returning a duration much larger than reality.
But menu and ladder can gracefully handle erroneously large duration
intervals without checking for CPUIDLE_FLAG_TIME_INVALID.
Further, if they don't check CPUIDLE_FLAG_TIME_INVALID, they
can also benefit from the instances when the duration interval
is not erroneously large.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CPUIDLE_FLAG_TIME_INVALID
When the ladder governor sees the CPUIDLE_FLAG_TIME_INVALID flag,
it unconditionally causes a state promotion by setting last_residency
to a number higher than the state's promotion_time:
last_residency = last_state->threshold.promotion_time + 1
It does this for fear that cpuidle_get_last_residency()
will be in-accurate, because cpuidle_enter_state() invoked
a state with CPUIDLE_FLAG_TIME_INVALID.
But the only state with CPUIDLE_FLAG_TIME_INVALID is
acpi_safe_halt(), which may return well after its actual
idle duration because it enables interrupts, so cpuidle_enter_state()
also measures interrupt service time.
So what? In ladder, a huge invalid last_residency has exactly
the same effect as the current code -- it unconditionally
causes a state promotion.
In the case where the idle residency plus measured interrupt
handling time is less than the state's demotion_time -- we should
use that timestamp to give ladder a chance to demote, rather than
unconditionally promoting.
This can be done by simply ignoring the CPUIDLE_FLAG_TIME_INVALID,
and using the "invalid" time, as it is either equal to what we are
doing today, or better.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
CPUIDLE_FLAG_TIME_INVALID
When menu sees CPUIDLE_FLAG_TIME_INVALID, it ignores its timestamps,
and assumes that idle lasted as long as the time till next predicted
timer expiration.
But if an interrupt was seen and serviced before that duration,
it would actually be more accurate to use the measured time
rather than rounding up to the next predicted timer expiration.
And if an interrupt is seen and serviced such that the mesured time
exceeds the time till next predicted timer expiration, then
truncating to that expiration is the right thing to do --
since we can never stay idle past that timer expiration.
So the code can do a better job without
checking for CPUIDLE_FLAG_TIME_INVALID.
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Tuukka Tikkanen <tuukka.tikkanen@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since there has been quite a lot of development going on for
ARM Exynos cpuidle driver recently I would like to add separate
MAINTAINERS entry for it and add myself as the primary maintainer.
The merging process would remain (almost) unchanged with patches
going (with my Ack) through Daniel's or Kukjin's tree.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Conflicts:
drivers/cpuidle/dt_idle_states.c
|
|
http://git.linaro.org/git-ro/people/daniel.lezcano/linux into pm-cpuidle
Pull ARM cpuidle material for 3.19-rc1 from Daniel Lezcano.
* 'cpuidle/3.19' of http://git.linaro.org/git-ro/people/daniel.lezcano/linux:
drivers: cpuidle: Remove cpuidle-arm64 duplicate error messages
drivers: cpuidle: Add idle-state-name description to ARM idle states
drivers: cpuidle: Add status property to ARM idle states
|
|
Current CPUidle driver for arm64 machines spits errors upon idle
state initialization and cpuidle driver registration failures.
These error messages are already printed in core code so there is
no need to print them again.
This patch removes the duplicate print messages from the cpuidle-arm64
driver.
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
On ARM machines, where generally speaking the idle state numbering has
no fixed and standard meaning it is useful to provide a description
of the idle state inner workings for benchmarking and monitoring purposes.
This patch adds a property to the idle states bindings that if present
gives platform firmware a means of describing the idle state and export
the string description to user space.
The patch updates the DT parsing code accordingly to take the description,
if present, into consideration.
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
On some platforms the device tree bindings must provide the kernel
with a status flag for idle states, that defines whether the idle
state is operational or not in the current configuration.
This patch adds a status property to the ARM idle states compliant
with ePAPR v1.1 and updates the DT parsing code accordingly.
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another small set of fixes:
- some DT compatible typo fixes
- irq setup fix dealing with irq storms on orion
- i2c quirk generalization for mvebu
- a handful of smaller fixes for OMAP
- a couple of added file patterns for OMAP entries in MAINTAINERS"
* tag 'armsoc-for-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: at91/dt: Fix sama5d3x typos
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
|
|
Pull sparc fixes from David Miller:
1) Fix NULL oops in Schizo PCI controller error handler.
2) Fix race between xchg and other operations on 32-bit sparc, from
Andreas Larsson.
3) swab*() helpers need a dummy memory input operand to show data flow
on 64-bit sparc.
4) Fix RCU warnings due to missing irq_{enter,exit}() around
generic_smp_call_function*() calls.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix constraints on swab helpers.
sparc32: Implement xchg and atomic_xchg using ATOMIC_HASH locks
sparc64: Do irq_{enter,exit}() around generic_smp_call_function*().
sparc64: Fix crashes in schizo_pcierr_intr_other().
|
|
Pull md bugfix from Neil Brown:
"One fix for md for 3.18.
This fixes a regression introduced in 3.13"
* tag 'md/3.18-fix' of git://neil.brown.name/md:
md: Always set RECOVERY_NEEDED when clearing RECOVERY_FROZEN
|
|
Some DT files had a typo with a missing "5" in sama5d3x first compatible string.
Signed-off-by: Peter Rosin <peda@axentia.se>
[nicolas.ferre@atmel.com: modify commit log]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v3.18-rc4" from Tony Lindgren:
Few omap fixes for hangs and wrong pinctrl defines, and update
MAINTAINERS file to avoid missing PMIC and SoC related patches:
- Fix random hangs on am437x because of incorrect default
value for the DDR regulator
- Fix wrong partition name for NAND on am335x-evm
- Fix wrong pinctrl defines for dra7xx
- Update maintainers entries for PMICs and SoCs
* tag 'omap-fixes-against-v3.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
pinctrl: dra: dt-bindings: Fix output pull up/down
MAINTAINERS: Update entry for omap related .dts files to cover new SoCs
MAINTAINERS: add more files under OMAP SUPPORT
ARM: dts: AM437x-SK-EVM: Fix DCDC3 voltage
ARM: dts: AM437x-GP-EVM: Fix DCDC3 voltage
ARM: dts: AM43x-EPOS-EVM: Fix DCDC3 voltage
ARM: dts: am335x-evm: Fix 5th NAND partition's name
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Merge "mvebu fixes for v3.18" from Jason Cooper:
- Armada XP
- Generalize i2c quirk
- orion
- Fix irq storm caused by specific sequence of request_irq
* tag 'mvebu-fixes-3.18' of git://git.infradead.org/linux-mvebu:
ARM: orion: Fix for certain sequence of request_irq can cause irq storm
ARM: mvebu: armada xp: Generalize use of i2c quirk
|
|
md_check_recovery will skip any recovery and also clear
MD_RECOVERY_NEEDED if MD_RECOVERY_FROZEN is set.
So when we clear _FROZEN, we must set _NEEDED and ensure that
md_check_recovery gets run.
Otherwise we could miss out on something that is needed.
In particular, this can make it impossible to remove a
failed device from an array is the 'recovery-needed' processing
didn't happen.
Suitable for stable kernels since 3.13.
Cc: stable@vger.kernel.org (3.13+)
Reported-and-tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Fixes: 30b8feb730f9b9b3c5de02580897da03f59b6b16
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
We are reading the memory location, so we have to have a memory
constraint in there purely for the sake of showing the data flow
to the compiler.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of six fixes and a MAINTAINER update.
The fixes are two multipath (one in Test Unit Ready handling for the
path checkers and one in the section of code that sends a start unit
after failover; both of these were perturbed by the scsi-mq update), a
CD-ROM door locking fix that was likewise introduced by scsi-mq and
three driver fixes for a previous code update in cxgb4i, megaraid_sas
and bnx2fc"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
bnx2fc: fix tgt spinlock locking
megaraid_sas: fix bug in handling return value of pci_enable_msix_range()
cxgb4i: send abort_rpl correctly
cxgbi: add maintainer for cxgb3i/cxgb4i
scsi: TUR path is down after adapter gets reset with multipath
scsi: call device handler for failed TUR command
scsi: only re-lock door after EH on devices that were reset
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"Microcode fixes, a Xen fix and a KASLR boot loading fix with certain
memory layouts"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Fix ucode patch stashing on 32-bit
x86/core, x86/xen/smp: Use 'die_complete' completion when taking CPU down
x86, microcode: Fix accessing dis_ucode_ldr on 32-bit
x86, kaslr: Prevent .bss from overlaping initrd
x86, microcode, AMD: Fix early ucode loading on 32-bit
|
|
Al Viro pointed out that the x86-64 csum_partial_copy_from_user() is
somewhat confused about what it should do on errors, notably it mostly
clears the uncopied end result buffer, but misses that for the initial
alignment case.
All users should check for errors, so it's dubious whether the clearing
is even necessary, and Al also points out that we should probably clean
up the calling conventions, but regardless of any future changes to this
function, the fact that it is inconsistent is just annoying.
So make the __get_user() failure path use the same error exit as all the
other errors do.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull ARM fixes from Russell King:
"Two fixes this time, one to ensure that the kuser helper option
depends on MMU as they aren't available for noMMU targets (and if the
option is selected, we end up oopsing.)
The second fix plugs a corner case with the decompressor, ensuring
that the instruction stream can see the relocated code in every case
on ARMv7 CPUs"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8198/1: make kuser helpers depend on MMU
ARM: 8191/1: decompressor: ensure I-side picks up relocated code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc updates from Helge Deller:
"Changes include:
- wire up the bpf syscall
- remove CONFIG_64BIT usage from some userspace-exported header files
- use compat functions for msgctl, shmat, shmctl and semtimedop
syscalls"
* 'parisc-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Avoid using CONFIG_64BIT in userspace exported headers
parisc: Use compat layer for msgctl, shmat, shmctl and semtimedop syscalls
parisc: Use BUILD_BUG() instead of undefined functions
parisc: Wire up bpf syscall
|
|
Pull power supply updates from Sebastian Reichel:
"Power supply and reset changes for the v3.18-rc:
- misc. charger-manager fixes
- year 2038 fix in ab8500_fg
- fix error handling of bq2415x_charger"
* tag 'for-v3.18-rc' of git://git.infradead.org/battery-2.6:
power: charger-manager: Fix accessing invalidated power supply after charger unbind
power: charger-manager: Fix accessing invalidated power supply after fuel gauge unbind
power: charger-manager: Avoid recursive thermal get_temp call
power_supply: Add no_thermal property to prevent recursive get_temp calls
power: bq2415x_charger: Fix memory leak on DTS parsing error
power: bq2415x_charger: Properly handle ENODEV from power_supply_get_by_phandle
power: ab8500_fg.c: use 64-bit time types
|
|
Pull drm gixes from Dave Airlie:
- exynos: infinite loop regressions fixed
- i915: one regression
- radeon: one race condition on monitor probing
- noveau: two regressions
- tegra: one vblank regression fix
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/tegra: dc: Add missing call to drm_vblank_on()
drm/nouveau/nv50/disp: Fix modeset on G94
drm/gk20a/fb: fix setting of large page size bit
drm/radeon: add locking around atombios scratch space usage
drm/i915: Fix obj->map_and_fenceable across tiling changes
drm/exynos: fix possible infinite loop issue
drm/exynos: g2d: fix null pointer dereference
drm/exynos: resolve infinite loop issue on non multi-platform
drm/exynos: resolve infinite loop issue on multi-platform
|
|
Sasha Levin reports:
"gcc5 changes the default standard to c11, which makes kernel build
unhappy
Explicitly define the kernel standard to be gnu89 which should keep
everything working exactly like it was before gcc5"
There are multiple small issues with the new default, but the biggest
issue seems to be that the old - and very useful - GNU extension to
allow a cast in front of an initializer has gone away.
Patch updated by Kirill:
"I'm pretty sure all gcc versions you can build kernel with supports
-std=gnu89. cc-option is redunrant.
We also need to adjust HOSTCFLAGS otherwise allmodconfig fails for me"
Note by Andrew Pinski:
"Yes it was reported and both problems relating to this extension has
been added to gnu99 and gnu11. Though there are other issues with the
kernel dealing with extern inline have different semantics between
gnu89 and gnu99/11"
End result: we may be able to move up to a newer stdc model eventually,
but right now the newer models have some annoying deficiencies, so the
traditional "gnu89" model ends up being the preferred one.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Singed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
- stable patches to fix NFSv4.x delegation reclaim error paths
- fix a bug whereby we were advertising NFSv4.1 but using NFSv4.2
features
- fix a use-after-free problem with pNFS block layouts
- fix a memory leak in the pNFS files O_DIRECT code
- replace an intrusive and Oops-prone performance fix in the NFSv4
atomic open code with a safer one-line version and revert the two
original patches"
* tag 'nfs-for-3.18-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
sunrpc: fix sleeping under rcu_read_lock in gss_stringify_acceptor
NFS: Don't try to reclaim delegation open state if recovery failed
NFSv4: Ensure that we call FREE_STATEID when NFSv4.x stateids are revoked
NFSv4: Fix races between nfs_remove_bad_delegation() and delegation return
NFSv4.1: nfs41_clear_delegation_stateid shouldn't trust NFS_DELEGATED_STATE
NFSv4: Ensure that we remove NFSv4.0 delegations when state has expired
NFS: SEEK is an NFS v4.2 feature
nfs: Fix use of uninitialized variable in nfs_getattr()
nfs: Remove bogus assignment
nfs: remove spurious WARN_ON_ONCE in write path
pnfs/blocklayout: serialize GETDEVICEINFO calls
nfs: fix pnfs direct write memory leak
Revert "NFS: nfs4_do_open should add negative results to the dcache."
Revert "NFS: remove BUG possibility in nfs4_open_and_get_state"
NFSv4: Ensure nfs_atomic_open set the dentry verifier on ENOENT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input subsystem updates from Dmitry Torokhov:
"Mostly small fixups to PS/2 tochpad drivers (ALPS, Elantech,
Synaptics) to better deal with specific hardware"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - update the documentation
Input: elantech - provide a sysfs knob for crc_enabled
Input: elantech - report the middle button of the touchpad
Input: alps - ignore bad data on Dell Latitudes E6440 and E7440
Input: alps - allow up to 2 invalid packets without resetting device
Input: alps - ignore potential bare packets when device is out of sync
Input: elantech - fix crc_enabled for Fujitsu H730
Input: elantech - use elantech_report_trackpoint for hardware v4 too
Input: twl4030-pwrbutton - ensure a wakeup event is recorded.
Input: synaptics - add min/max quirk for Lenovo T440s
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- fix EFI stub cache maintenance causing aborts during boot on certain
platforms
- handle byte stores in __clear_user without panicking
- fix race condition in aarch64_insn_patch_text_sync() (instruction
patching)
- Couple of type fixes
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: ARCH_PFN_OFFSET should be unsigned long
Correct the race condition in aarch64_insn_patch_text_sync()
arm64: __clear_user: handle exceptions on strb
arm64: Fix data type for physical address
arm64: efi: Fix stub cache maintenance
|
|
git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers fixlets from Darren Hart:
"Just two patches to remove hp_accel events from the keyboard bus
stream via an i8042 filter"
* tag 'platform-drivers-x86-v3.18-3' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform: hp_accel: Add SERIO_I8042 as a dependency since it now includes i8042.h/serio.h
platform: hp_accel: add a i8042 filter to remove HPQ6000 data from kb bus stream
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"The most notable is the revert of lock splitting optimization in ahci.
This also made the IRQ handling threaded even when there's only one
IRQ in use. The conversion missed IRFQ_SHARED leading to screaming
IRQs problem in some cases and the threaded IRQ handling showed
performance regression in some LKP test cases. The changes are
reverted for now. It'll probably be retried once threaded IRQ
handling is removed from ahci.
Other than that, there's one fix for ahci and several patches adding
device IDs"
* 'for-3.18-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: fix AHCI parameters not taken into account
ata: sata_rcar: Add r8a7793 device support
ahci: Add Device IDs for Intel Sunrise Point PCH
ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks
Revert "AHCI: Optimize single IRQ interrupt processing"
Revert "AHCI: Do not acquire ata_host::lock from single IRQ handler"
ata: sata_rcar: Disable DIPM mode for r8a7790 ES1
|
|
Pull block layer fixes from Jens Axboe:
"Four small fixes that should be merged for the current 3.18-rc series.
This pull request contains:
- a minor bugfix for computation of best IO priority given two
merging requests. From Jan Kara.
- the final (final) merge count issue that has been plaguing
virtio-blk. From Ming Lei.
- enable parallel reinit notify for blk-mq queues, to combine the
cost of an RCU grace period across lots of devices. From Tejun
Heo.
- an error handling fix for the SCSI_IOCTL_SEND_COMMAND ioctl. From
Tony Battersby"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: blk-merge: fix blk_recount_segments()
scsi: Fix more error handling in SCSI_IOCTL_SEND_COMMAND
blk-mq: make mq_queue_reinit_notify() freeze queues in parallel
block: Fix computation of merged request priority
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are three regression fixes, two recent (generic power domains,
suspend-to-idle) and one older (cpufreq), an ACPI blacklist entry for
one more machine having problems with Windows 8 compatibility, a minor
cpufreq driver fix (cpufreq-dt) and a fixup for new callback
definitions (generic power domains).
Specifics:
- Fix a crash in the suspend-to-idle code path introduced by a recent
commit that forgot to check a pointer against NULL before
dereferencing it (Dmitry Eremin-Solenikov).
- Fix a boot crash on Exynos5 introduced by a recent commit making
that platform use generic Device Tree bindings for power domains
which exposed a weakness in the generic power domains framework
leading to that crash (Ulf Hansson).
- Fix a crash during system resume on systems where cpufreq depends
on Operation Performance Points (OPP) for functionality, but
CONFIG_OPP is not set. This leads the cpufreq driver registration
to fail, but the resume code attempts to restore the pre-suspend
cpufreq configuration (which does not exist) nevertheless and
crashes. From Geert Uytterhoeven.
- Add a new ACPI blacklist entry for Dell Vostro 3546 that has
problems if it is reported as Windows 8 compatible to the BIOS
(Adam Lee).
- Fix swapped arguments in an error message in the cpufreq-dt driver
(Abhilash Kesavan).
- Fix up the prototypes of new callbacks in struct generic_pm_domain
to make them more useful. Users of those callbacks will be added
in 3.19 and it's better for them to be based on the correct struct
definition in mainline from the start. From Ulf Hansson and Kevin
Hilman"
* tag 'pm+acpi-3.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix initial default state of the need_restore flag
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
PM / Domains: Change prototype for the attach and detach callbacks
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
ACPI / blacklist: blacklist Win8 OSI for Dell Vostro 3546
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull firewire fix from Stefan Richter:
"IEEE 1394 (FireWire) subsystem fix: The character device file
interface for raw 1394 I/O took uninitialized kernel stack as
substitute for missing ioctl() argument data. This could partially
show up in subsequent read() output"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: cdev: prevent kernel stack leaking into ioctl arguments
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fix from Al Viro:
"Fix for a really embarrassing braino in iov_iter. Kudos to paulus..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Fix thinko in iov_iter_single_seg_count
|
|
* pm-domains:
PM / Domains: Fix initial default state of the need_restore flag
PM / Domains: Change prototype for the attach and detach callbacks
* pm-sleep:
PM / sleep: Fix entering suspend-to-IDLE if no freeze_oops is set
* pm-cpufreq:
cpufreq: Avoid crash in resume on SMP without OPP
cpufreq: cpufreq-dt: Fix arguments in clock failure error message
|
|
* acpi-blacklist:
ACPI / blacklist: blacklist Win8 OSI for Dell Vostro 3546
|
|
Found by the UC-KLEE tool: A user could supply less input to
firewire-cdev ioctls than write- or write/read-type ioctl handlers
expect. The handlers used data from uninitialized kernel stack then.
This could partially leak back to the user if the kernel subsequently
generated fw_cdev_event_'s (to be read from the firewire-cdev fd)
which notably would contain the _u64 closure field which many of the
ioctl argument structures contain.
The fact that the handlers would act on random garbage input is a
lesser issue since all handlers must check their input anyway.
The fix simply always null-initializes the entire ioctl argument buffer
regardless of the actual length of expected user input. That is, a
runtime overhead of memset(..., 40) is added to each firewirew-cdev
ioctl() call. [Comment from Clemens Ladisch: This part of the stack is
most likely to be already in the cache.]
Remarks:
- There was never any leak from kernel stack to the ioctl output
buffer itself. IOW, it was not possible to read kernel stack by a
read-type or write/read-type ioctl alone; the leak could at most
happen in combination with read()ing subsequent event data.
- The actual expected minimum user input of each ioctl from
include/uapi/linux/firewire-cdev.h is, in bytes:
[0x00] = 32, [0x05] = 4, [0x0a] = 16, [0x0f] = 20, [0x14] = 16,
[0x01] = 36, [0x06] = 20, [0x0b] = 4, [0x10] = 20, [0x15] = 20,
[0x02] = 20, [0x07] = 4, [0x0c] = 0, [0x11] = 0, [0x16] = 8,
[0x03] = 4, [0x08] = 24, [0x0d] = 20, [0x12] = 36, [0x17] = 12,
[0x04] = 20, [0x09] = 24, [0x0e] = 4, [0x13] = 40, [0x18] = 4.
Reported-by: David Ramos <daramos@stanford.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
Pull virtio bugfix from Michael S Tsirkin:
"This fixes a crash in virtio console multi-channel mode that got
introduced in -rc1"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: move early VQ enablement
|
|
Pull networking fixes from David Miller:
1) sunhme driver lacks DMA mapping error checks, based upon a report by
Meelis Roos.
2) Fix memory leak in mvpp2 driver, from Sudip Mukherjee.
3) DMA memory allocation sizes are wrong in systemport ethernet driver,
fix from Florian Fainelli.
4) Fix use after free in mac80211 defragmentation code, from Johannes
Berg.
5) Some networking uapi headers missing from Kbuild file, from Stephen
Hemminger.
6) TUN driver gets csum_start offset wrong when VLAN accel is enabled,
and macvtap has a similar bug, from Herbert Xu.
7) Adjust several tunneling drivers to set dev->iflink after registry,
because registry sets that to -1 overwriting whatever we did. From
Steffen Klassert.
8) Geneve forgets to set inner tunneling type, causing GSO segmentation
to fail on some NICs. From Jesse Gross.
9) Fix several locking bugs in stmmac driver, from Fabrice Gasnier and
Giuseppe CAVALLARO.
10) Fix spurious timeouts with NewReno on low traffic connections, from
Marcelo Leitner.
11) Fix descriptor updates in enic driver, from Govindarajulu
Varadarajan.
12) PPP calls bpf_prog_create() with locks held, which isn't kosher.
Fix from Takashi Iwai.
13) Fix NULL deref in SCTP with malformed INIT packets, from Daniel
Borkmann.
14) psock_fanout selftest accesses past the end of the mmap ring, fix
from Shuah Khan.
15) Fix PTP timestamping for VLAN packets, from Richard Cochran.
16) netlink_unbind() calls in netlink pass wrong initial argument, from
Hiroaki SHIMODA.
17) vxlan socket reuse accidently reuses a socket when the address
family is different, so we have to explicitly check this, from
Marcelo Lietner.
18) Fix missing include in nft_reject_bridge.c breaking the build on ppc
and other architectures, from Guenter Roeck.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
vxlan: Do not reuse sockets for a different address family
smsc911x: power-up phydev before doing a software reset.
lib: rhashtable - Remove weird non-ASCII characters from comments
net/smsc911x: Fix delays in the PHY enable/disable routines
net/smsc911x: Fix rare soft reset timeout issue due to PHY power-down mode
netlink: Properly unbind in error conditions.
net: ptp: fix time stamp matching logic for VLAN packets.
cxgb4 : dcb open-lldp interop fixes
selftests/net: psock_fanout seg faults in sock_fanout_read_ring()
net: bcmgenet: apply MII configuration in bcmgenet_open()
net: bcmgenet: connect and disconnect from the PHY state machine
net: qualcomm: Fix dependency
ixgbe: phy: fix uninitialized status in ixgbe_setup_phy_link_tnx
net: phy: Correctly handle MII ioctl which changes autonegotiation.
ipv6: fix IPV6_PKTINFO with v4 mapped
net: sctp: fix memory leak in auth key management
net: sctp: fix NULL pointer dereference in af->from_addr_param on malformed packet
net: ppp: Don't call bpf_prog_create() in ppp_lock
net/mlx4_en: Advertize encapsulation offloads features only when VXLAN tunnel is set
cxgb4 : Fix bug in DCB app deletion
...
|
|
A chapter is added to describe the trackpoint packets.
A section is added to describe the behaviour of the knob crc_enabled in
sysfs.
The introduction of the documentation only mentioned v1/v2, but in the
last part it already contains explanation of v3 and v4. The introduction
is updated.
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The detection of crc_enabled is known to fail for Fujitsu H730. A DMI
blacklist is added for that, but it can be expected that other laptops will
pop up with this.
Here a sysfs knob is provided to alter the behaviour of crc_enabled.
Writing 0 or 1 to it sets the variable to 0 or 1. Reading it will show the
crc_enabled variable (0 or 1).
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In the past, no elantech was known with 3 touchpad mouse buttons.
Fujitsu H730 is the first known elantech with a middle button. This commit
enables this middle button. For backwards compatibility, the Fujitsu is
detected via DMI, and only for this one 3 buttons will be announced.
Reported-by: Stefan Valouch <stefan@valouch.com>
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Sometimes on Dell Latitude laptops psmouse/alps driver receive invalid ALPS
protocol V3 packets with bit7 set in last byte. More often it can be
reproduced on Dell Latitude E6440 or E7440 with closed lid and pushing
cover above touchpad.
If bit7 in last packet byte is set then it is not valid ALPS packet. I was
told that ALPS devices never send these packets. It is not know yet who
send those packets, it could be Dell EC, bug in BIOS and also bug in
touchpad firmware...
With this patch alps driver does not process those invalid packets, but
instead of reporting PSMOUSE_BAD_DATA, getting into out of sync state,
getting back in sync with the next byte and spam dmesg we return
PSMOUSE_FULL_PACKET. If driver is truly out of sync we'll fail the checks
on the next byte and report PSMOUSE_BAD_DATA then.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Merge misc fixes from Andrew Morton:
"15 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
MAINTAINERS: add IIO include files
kernel/panic.c: update comments for print_tainted
mem-hotplug: reset node present pages when hot-adding a new pgdat
mem-hotplug: reset node managed pages when hot-adding a new pgdat
mm/debug-pagealloc: correct freepage accounting and order resetting
fanotify: fix notification of groups with inode & mount marks
mm, compaction: prevent infinite loop in compact_zone
mm: alloc_contig_range: demote pages busy message from warn to info
mm/slab: fix unalignment problem on Malta with EVA due to slab merge
mm/page_alloc: restrict max order of merging on isolated pageblock
mm/page_alloc: move freepage counting logic to __free_one_page()
mm/page_alloc: add freepage on isolate pageblock to correct buddy list
mm/page_alloc: fix incorrect isolation behavior by rechecking migratetype
mm/compaction: skip the range until proper target pageblock is met
zram: avoid kunmap_atomic() of a NULL pointer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"There is an overflow bug fix for cephfs from Zheng, a fix for handling
large authentication ticket buffers in libceph from Ilya, and a few
fixes for the request handling code from Ilya that affect RBD volumes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: change from BUG to WARN for __remove_osd() asserts
libceph: clear r_req_lru_item in __unregister_linger_request()
libceph: unlink from o_linger_requests when clearing r_osd
libceph: do not crash on large auth tickets
ceph: fix flush tid comparision
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for an oops in HID core upon repeated subdriver insertion/removal
under certain circumstances, by Benjamin Tissoires
- quirk for another Elan Touchscreen device, by Adel Gadllah
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: core: cleanup .claimed field on disconnect
HID: usbhid: enable always-poll quirk for Elan Touchscreen 0103
|
|
Files under include/linux/iio were not reported as part of the IIO
subsystem.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reported-by: Cristina Ciocan <cristina.ciocan@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 69361eef9056 ("panic: add TAINT_SOFTLOCKUP") added the 'L' flag,
but failed to update the comments for print_tainted(). So, update the
comments.
Signed-off-by: Xie XiuQi <xiexiuqi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When memory is hot-added, all the memory is in offline state. So clear
all zones' present_pages because they will be updated in online_pages()
and offline_pages(). Otherwise, /proc/zoneinfo will corrupt:
When the memory of node2 is offline:
# cat /proc/zoneinfo
......
Node 2, zone Movable
......
spanned 8388608
present 8388608
managed 0
When we online memory on node2:
# cat /proc/zoneinfo
......
Node 2, zone Movable
......
spanned 8388608
present 16777216
managed 8388608
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [3.16+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
