| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch is to support DPAA (Data Path Acceleration Architecture)
1588 timer by adding "fsl,fman-ptp-timer" compatible, sharing
interrupt with FMan, adding FSL_DPAA_ETH dependency, and fixing
up register offset.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to share fman event interrupt because
the 1588 timer driver will also use this interrupt.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
mlxsw: Support bridge router interfaces with non-default VLAN
Petr says:
When traffic is inserted on a router interface associated with an 802.1q
bridge, the VLAN that the traffic appears on is determined by PVID of
the bridge device itself. However currently mlxsw always configures such
traffic to be forwarded to VLAN 1, regardless of the bridge PVID.
Fix the problem by modifying the FID-handling code to assign such
traffic not to FID that corresponds to VLAN 1, but to a FID that
corresponds to the configured PVID. Bail out if there is no PVID. This
is implemented in patches #1 and #2.
From that point on, also forbid any changes to bridge device PVID,
because such changes would not be reflected. This is implemented in
patches #3, #4 and #5.
Finally in patch #6, introduce tests that use bridge as a routed
interface, and test mlxsw in both the currently-supported scenario of
using PVID 1, and the newly-supported one of using a custom PVID.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add test for cases where bridge itself acts as a router interface, with
front panel port attached to the bridge in question.
In the first test (router_bridge.sh), VLAN memberships are not
configured in any way, and everything uses default PVID of 1. Thus
traffic in $h1 and $h2 is untagged. This test ensures that the previous
patches didn't break a currently working scenario.
In the second test (router_bridge_vlan.sh), a VLAN 555 pvid untagged is
added to the bridge CPU port, with that VLAN leaving the bridge tagged
through its sole member port. The traffic is therefore expected to come
out tagged at $h1. This tests the fix introduced in the previous
patches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When traffic passes through a router port, it needs to be assigned a FID
for ASIC to forward correctly. For bridges, this FID used to be the one
corresponding to VLAN 1. In a previous patch, this was changed to
instead use the PVID at the time that the RIF is created. This patch
guards PVID changes after the RIF was introduced.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to allow querying of the VID for which a RIF was created, add
a new function that returns a FID for a given RIF.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to guard against removal of a PVID for which a FID was
allocated, spectrum_switchdev needs to first determine whether there is
a RIF associated with a given bridge. To that end, publish a preexisting
function mlxsw_sp_rif_find_by_dev().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For bridge netdevices, instead of assuming that the router traffic is on
VLAN 1, look at the bridge PVID.
This patch assumes that the PVID doesn't change after the router
interface is created (i.e. after the IP address is assigned).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the follow-up patch, mlxsw_sp_rif_vlan_fid_get() will be changed in a
way that could fail. Give that function a possibility to explain the
failure through extack.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will be helpful if we could display the drops due to zero window or no
enough window space.
So a new SNMP MIB entry is added to track this behavior.
This entry is named LINUX_MIB_TCPZEROWINDOWDROP and published in
/proc/net/netstat in TcpExt line as TCPZeroWindowDrop.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert GRO receive over to hash table.
When many parallel flows are present and being received on the same
RX queue, GRO processing can become expensive because each incoming
frame must traverse the per-NAPI GRO list at each protocol layer
of GRO receive (eth --> ipv{4,6} --> tcp).
Use the already computed hash to chain these SKBs in a hash table
instead of a simple list.
The first patch makes the GRO list a true list_head.
The second patch implements the hash table.
This series patches basic testing and I added some diagnostics
to make sure we really were aggregating GRO frames :-)
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Improve the performance of GRO receive by splitting flows into
multiple hash chains.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manage pending per-NAPI GRO packets via list_head.
Return an SKB pointer from the GRO receive handlers. When GRO receive
handlers return non-NULL, it means that this SKB needs to be completed
at this time and removed from the NAPI queue.
Several operations are greatly simplified by this transformation,
especially timing out the oldest SKB in the list when gro_count
exceeds MAX_GRO_SKBS, and napi_gro_flush() which walks the queue
in reverse order.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull networking fixes from David Miller:
1) Fix netpoll OOPS in r8169, from Ville Syrjälä.
2) Fix bpf instruction alignment on powerpc et al., from Eric Dumazet.
3) Don't ignore IFLA_MTU attribute when creating new ipvlan links. From
Xin Long.
4) Fix use after free in AF_PACKET, from Eric Dumazet.
5) Mis-matched RTNL unlock in xen-netfront, from Ross Lagerwall.
6) Fix VSOCK loopback on big-endian, from Claudio Imbrenda.
7) Missing RX buffer offset correction when computing DMA addresses in
mvneta driver, from Antoine Tenart.
8) Fix crashes in DCCP's ccid3_hc_rx_send_feedback, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
sfc: make function efx_rps_hash_bucket static
strparser: Corrected typo in documentation.
qmi_wwan: add support for the Dell Wireless 5821e module
cxgb4: when disabling dcb set txq dcb priority to 0
net_sched: remove a bogus warning in hfsc
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
net: Remove depends on HAS_DMA in case of platform dependency
MAINTAINERS: Add file patterns for dsa device tree bindings
net: mscc: make sparse happy
net: mvneta: fix the Rx desc DMA address in the Rx path
Documentation: e1000: Fix docs build error
Documentation: e100: Fix docs build error
Documentation: e1000: Use correct heading adornment
Documentation: e100: Use correct heading adornment
ipv6: mcast: fix unsolicited report interval after receiving querys
vhost_net: validate sock before trying to put its fd
VSOCK: fix loopback on big-endian systems
net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
xen-netfront: Update features after registering netdev
...
|
|
Heiner Kallweit says:
====================
r8169: improve PHY initialization and WoL handling
Series with smaller improvements regarding PHY initialization and
WoL handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can power down the PHY irregardless of WOL settings if interface
is down. So far we would have left the PHY enabled if WOL options
are set and the interface is brought down.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's make saved_wolopts a shadow copy of the WoL options. This allows
to simplify the code and get rid of calls to now unneeded function
__rtl8169_get_wol(). However don't remove __rtl8169_get_wol()
completely to be prepared for the case that we can respect BIOS WOL
settings again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's move calling rtl8169_init_phy() to __rtl8169_resume().
It simplifies the code and avoids rtl8169_init_phy() being called
when resuming whilst interface is down. rtl_open() will initialize
the PHY when the interface is brought up.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
net: sched: couple of ndo_setup_tc fixes and adjustments
This patchset includes couple of patches that fix or adjust default
cases and return values in ndo_setup_tc implementations in drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
-EOPNOTSUPP is the error value that should be reported if a flower
command is not supported by a driver. Fix it in couple of Intel drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the default case is not handled, which with future command
introductions would introduce a warning. So handle it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the default case is not handled, which with future command
introductions would introduce a warning. So handle it and make the
switch a bit simplier removing unneeded "rc" variable.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removed unused variable 'rxm' from tls_queue().
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function efx_rps_hash_bucket is local to the source and
does not need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'efx_rps_hash_bucket' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
"A pile of perf updates:
Kernel side:
- Remove an incorrect warning in uprobe_init_insn() when
insn_get_length() fails. The error return code is handled at the
call site.
- Move the inline keyword to the right place in the perf ringbuffer
code to address a W=1 build warning.
Tooling:
perf stat:
- Fix metric column header display alignment
- Improve error messages for default attributes, providing better
output for error in command line.
- Add --interval-clear option, to provide a 'watch' like printing
perf script:
- Show hw-cache events too
perf c2c:
- Fix data dependency problem in layout of 'struct c2c_hist_entry'
Core:
- Do not blindly assume that 'struct perf_evsel' can be obtained via
a straight forward container_of() as there are call sites which
hand in a plain 'struct hist' which is not part of a container.
- Fix error index in the PMU event parser, so that error messages can
point to the problematic token"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Move the inline keyword at the beginning of the function declaration
uprobes/x86: Remove incorrect WARN_ON() in uprobe_init_insn()
perf script: Show hw-cache events
perf c2c: Keep struct hist_entry at the end of struct c2c_hist_entry
perf stat: Add event parsing error handling to add_default_attributes
perf stat: Allow to specify specific metric column len
perf stat: Fix metric column header display alignment
perf stat: Use only color_fprintf call in print_metric_only
perf stat: Add --interval-clear option
perf tools: Fix error index for pmu event parser
perf hists: Reimplement hists__has_callchains()
perf hists browser gtk: Use hist_entry__has_callchains()
perf hists: Make hist_entry__has_callchains() work with 'perf c2c'
perf hists: Save the callchain_size in struct hist_entry
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq fixes from Thomas Gleixer:
"A pile of rseq related fixups:
- Prevent infinite recursion when delivering SIGSEGV
- Remove the abort of rseq critical section on fork() as syscalls
inside rseq critical sections are explicitely forbidden. So no
point in doing the abort on the child.
- Align the rseq structure on 32 bytes in the ARM selftest code.
- Fix file permissions of the test script"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Avoid infinite recursion when delivering SIGSEGV
rseq/cleanup: Do not abort rseq c.s. in child on fork()
rseq/selftests/arm: Align 'struct rseq_cs' on 32 bytes
rseq/selftests: Make run_param_test.sh executable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI fixes from Thomas Gleixner:
"Two fixlets for the EFI maze:
- Properly zero variables to prevent an early boot hang on EFI mixed
mode systems
- Fix the fallout of merging the 32bit and 64bit variants of EFI PCI
related code which ended up chosing the 32bit variant of the actual
EFi call invocation which leads to failures on 64bit"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi/x86: Fix incorrect invocation of PciIo->Attributes()
efi/libstub/tpm: Initialize efi_physical_addr_t vars to zero for mixed mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"Two tiny fixes:
- Add the missing machine_real_restart() to objtools noreturn list so
it stops complaining
- Fix a trivial comment typo"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel.h: Fix a typo in comment
objtool: Add machine_real_restart() to the noreturn list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Make Xen PV guest deal with speculative store bypass correctly
- Address more fallout from the 5-Level pagetable handling. Undo an
__initdata annotation to avoid section mismatch and malfunction
when post init code would touch the freed variable.
- Handle exception fixup in math_error() before calling notify_die().
The reverse call order incorrectly triggers notify_die() listeners
for soemthing which is handled correctly at the site which issues
the floating point instruction.
- Fix an off by one in the LLC topology calculation on AMD
- Handle non standard memory block sizes gracefully un UV platforms
- Plug a memory leak in the microcode loader
- Sanitize the purgatory build magic
- Add the x86 specific device tree bindings directory to the x86
MAINTAINER file patterns"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix 'no5lvl' handling
Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
x86/CPU/AMD: Fix LLC ID bit-shift calculation
MAINTAINERS: Add file patterns for x86 device tree bindings
x86/microcode/intel: Fix memleak in save_microcode_patch()
x86/platform/UV: Add kernel parameter to set memory block size
x86/platform/UV: Use new set memory block size function
x86/platform/UV: Add adjustable set memory block size function
x86/build: Remove unnecessary preparation for purgatory
Revert "kexec/purgatory: Add clean-up for purgatory directory"
x86/xen: Add call of speculative_store_bypass_ht_init() to PV paths
x86: Call fixup_exception() before notify_die() in math_error()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 pti fixes from Thomas Gleixner:
"Two small updates for the speculative distractions:
- Make it more clear to the compiler that array_index_mask_nospec()
is not subject for optimizations. It's not perfect, but ...
- Don't report XEN PV guests as vulnerable because their mitigation
state depends on the hypervisor. Report unknown and refer to the
hypervisor requirement"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/spectre_v1: Disable compiler optimizations over array_index_mask_nospec()
x86/pti: Don't report XenPV as vulnerable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of fixes and updates for the locking code:
- Prevent lockdep from updating irq state within its own code and
thereby confusing itself.
- Buid fix for older GCCs which mistreat anonymous unions
- Add a missing lockdep annotation in down_read_non_onwer() which
causes up_read_non_owner() to emit a lockdep splat
- Remove the custom alpha dec_and_lock() implementation which is
incorrect in terms of ordering and use the generic one.
The remaining two commits are not strictly fixes. They provide irqsave
variants of atomic_dec_and_lock() and refcount_dec_and_lock(). These
are required to merge the relevant updates and cleanups into different
maintainer trees for 4.19, so routing them into mainline without
actual users is the sanest approach.
They should have been in -rc1, but last weekend I took the liberty to
just avoid computers in order to regain some mental sanity"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/qspinlock: Fix build for anonymous union in older GCC compilers
locking/lockdep: Do not record IRQ state within lockdep code
locking/rwsem: Fix up_read_non_owner() warning with DEBUG_RWSEMS
locking/refcounts: Implement refcount_dec_and_lock_irqsave()
atomic: Add irqsave variant of atomic_dec_and_lock()
alpha: Remove custom dec_and_lock() implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull ras fixes from Thomas Gleixner:
"A set of fixes for RAS/MCE:
- Improve the error message when the kernel cannot recover from a MCE
so the maximum amount of information gets provided.
- Individually check MCE recovery features on SkyLake CPUs instead of
assuming none when the CAPID0 register does not advertise the
general ability for recovery.
- Prevent MCE to output inconsistent messages which first show an
error location and then claim that the source is unknown.
- Prevent overwriting MCi_STATUS in the attempt to gather more
information when a fatal MCE has alreay been detected. This leads
to empty status values in the printout and failing to react
promptly on the fatal event"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix incorrect "Machine check from unknown source" message
x86/mce: Do not overwrite MCi_STATUS in mce_no_way_out()
x86/mce: Check for alternate indication of machine check recovery on Skylake
x86/mce: Improve error message when kernel cannot recover
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for time(r) related issues:
- Fix a long standing conversion issue in jiffies_to_msecs() for odd
HZ values like 1024 or 1200 which resulted in returning 0 for small
jiffies values due to rounding down.
- Use the proper CONFIG symbol in the new Y2038 safe compat code for
posix-timers. Not yet a visible breakage, but this will immediately
trigger when the architecture support for the new interfaces is
merged.
- Return an error code in the STM32 clocksource driver on failure
instead of success.
- Remove the redundant and stale irq disabled check in the posix cpu
timer code. The check is at the wrong place anyway and lockdep
already covers it via the sighand lock locking coverage"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
time: Make sure jiffies_to_msecs() preserves non-zero time periods
posix-timers: Fix nanosleep_copyout() for CONFIG_COMPAT_32BIT_TIME
clocksource/drivers/stm32: Fix error return code
posix-cpu-timers: Remove lockdep_assert_irqs_disabled()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes mostly for the ARM/GIC world:
- Fix the MSI affinity handling in the ls-scfg irq chip driver so it
updates and uses the effective affinity mask correctly
- Prevent binding LPIs to offline CPUs and respect the Cavium erratum
which requires that LPIs which belong to an offline NUMA node are
not bound to a CPU on a different NUMA node.
- Free only the amount of allocated interrupts in the GIC-V2M driver
instead of trying to free log2(nrirqs).
- Prevent emitting SYNC and VSYNC targetting non existing interrupt
collections in the GIC-V3 ITS driver
- Ensure that the GIV-V3 interrupt redistributor is correctly
reprogrammed on CPU hotplug
- Remove a stale unused helper function"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdesc: Delete irq_desc_get_msi_desc()
irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
irqchip/gic-v2m: Fix SPI release on error path
irqchip/ls-scfg-msi: Fix MSI affinity handling
genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few MIPS fixes for 4.18:
- a GPIO device name fix for a regression in v4.15-rc1.
- an errata workaround for the BCM5300X platform.
- a fix to ftrace function graph tracing, broken for a long time with
the fix applying cleanly back as far as v3.17.
- addition of read barriers to in{b,w,l,q}() functions, matching
behavior of other architectures & mirroring the equivalent addition
to read{b,w,l,q} in v4.17-rc2.
Plus changes to wire up new syscalls introduced in the 4.18 cycle:
- Restartable sequences support is added, including MIPS support in
the selftests.
- io_pgetevents is wired up"
* tag 'mips_fixes_4.18_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: Wire up io_pgetevents syscall
rseq/selftests: Implement MIPS support
MIPS: Wire up the restartable sequences (rseq) syscall
MIPS: Add syscall detection for restartable sequences
MIPS: Add support for restartable sequences
MIPS: io: Add barrier after register read in inX()
mips: ftrace: fix static function graph tracing
MIPS: BCM47XX: Enable 74K Core ExternalSync for PCIe erratum
MIPS: pb44: Fix i2c-gpio GPIO descriptor table
|
|
After commit a09ceb0e0814 ("sched: remove qdisc->drop"),
it is no longer used.
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When platform_device_register_simple() fails we can return
the error immediately instead of jumping to the 'err_pdev'
label.
This makes the error path a bit simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replaced strp_pause() with strp_unpause() to correct a seemingly copy
paste documentation mistake.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following commit:
2c3625cb9fa2 ("efi/x86: Fold __setup_efi_pci32() and __setup_efi_pci64() into one function")
... merged the two versions of __setup_efi_pciXX(), without taking into
account that the 32-bit version used a rather dodgy trick to pass an
immediate 0 constant as argument for a uint64_t parameter.
The issue is caused by the fact that on x86, UEFI protocol method calls
are redirected via struct efi_config::call(), which is a variadic function,
and so the compiler has to infer the types of the parameters from the
arguments rather than from the prototype.
As the 32-bit x86 calling convention passes arguments via the stack,
passing the unqualified constant 0 twice is the same as passing 0ULL,
which is why the 32-bit code in __setup_efi_pci32() contained the
following call:
status = efi_early->call(pci->attributes, pci,
EfiPciIoAttributeOperationGet, 0, 0,
&attributes);
to invoke this UEFI protocol method:
typedef
EFI_STATUS
(EFIAPI *EFI_PCI_IO_PROTOCOL_ATTRIBUTES) (
IN EFI_PCI_IO_PROTOCOL *This,
IN EFI_PCI_IO_PROTOCOL_ATTRIBUTE_OPERATION Operation,
IN UINT64 Attributes,
OUT UINT64 *Result OPTIONAL
);
After the merge, we inadvertently ended up with this version for both
32-bit and 64-bit builds, breaking the latter.
So replace the two zeroes with the explicitly typed constant 0ULL,
which works as expected on both 32-bit and 64-bit builds.
Wilfried tested the 64-bit build, and I checked the generated assembly
of a 32-bit build with and without this patch, and they are identical.
Reported-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Tested-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: hdegoede@redhat.com
Cc: linux-efi@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This module exposes two USB configurations: a QMI+AT capable setup on
USB config #1 and a MBIM capable setup on USB config #2.
By default the kernel will choose the MBIM capable configuration as
long as the cdc_mbim driver is available. This patch adds support for
the QMI port in the secondary configuration.
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we are disabling DCB, store "0" in txq->dcb_prio
since that's used for future TX Work Request "OVLAN_IDX"
values. Setting non zero priority upon disabling DCB
would halt the traffic.
Reported-by: AMG Zollner Robert <robert@cloudmedia.eu>
CC: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
- Further timeout fixes. We aren't quite there yet, so expect another
round of fixes for that to completely close some of the IRQ vs
completion races. (Christoph/Bart)
- Set of NVMe fixes from the usual suspects, mostly error handling
- Two off-by-one fixes (Dan)
- Another bdi race fix (Jan)
- Fix nbd reconfigure with NBD_DISCONNECT_ON_CLOSE (Doron)
* tag 'for-linus-20180623' of git://git.kernel.dk/linux-block:
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
bdi: Fix another oops in wb_workfn()
lightnvm: Remove depends on HAS_DMA in case of platform dependency
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
nvme-fc: release io queues to allow fast fail
nbd: Add the nbd NBD_DISCONNECT_ON_CLOSE config flag.
block: sed-opal: Fix a couple off by one bugs
blk-mq-debugfs: Off by one in blk_mq_rq_state_name()
nvmet: reset keep alive timer in controller enable
nvme-rdma: don't override opts->queue_size
nvme-rdma: Fix command completion race at error recovery
nvme-rdma: fix possible free of a non-allocated async event buffer
nvme-rdma: fix possible double free condition when failing to create a controller
Revert "block: Add warning for bi_next not NULL in bio_endio()"
block: fix timeout changes for legacy request drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- Fix use after free in chtls
- Fix RBP breakage in sha3
- Fix use after free in hwrng_unregister
- Fix overread in morus640
- Move sleep out of kernel_neon in arm64/aes-blk
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: core - Always drop the RNG in hwrng_unregister()
crypto: morus640 - Fix out-of-bounds access
crypto: don't optimize keccakf()
crypto: arm64/aes-blk - fix and move skcipher_walk_done out of kernel_neon_begin, _end
crypto: chtls - use after free in chtls_pt_recvmsg()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fixes from Shuah Khan:
- fix new sparc64 adi driver test compile errors on non-sparc systems
- fix config fragment for sync framework for improved test coverage
- fix several tests to return correct Kselftest skip code
* tag 'linux-kselftest-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: sparc64: Add missing SPDX License Identifiers
selftests: sparc64: delete RUN_TESTS and EMIT_TESTS overrides
selftests: sparc64: Fix to do nothing on non-sparc64
selftests: sync: add config fragment for testing sync framework
selftests: vm: return Kselftest Skip code for skipped tests
selftests: zram: return Kselftest Skip code for skipped tests
selftests: user: return Kselftest Skip code for skipped tests
selftests: sysctl: return Kselftest Skip code for skipped tests
selftests: static_keys: return Kselftest Skip code for skipped tests
selftests: pstore: return Kselftest Skip code for skipped tests
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This contains a few fixes and a clean up.
- a bad merge caused an "endif" to go in the wrong place in
scripts/Makefile.build
- softirq tracing fix for tracing that corrupts lockdep and causes a
false splat
- histogram documentation typo fixes
- fix a bad memory reference when passing in no filter to the filter
code
- simplify code by using the swap macro instead of open coding the
swap"
* tag 'trace-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix SKIP_STACK_VALIDATION=1 build due to bad merge with -mrecord-mcount
tracing: Fix some errors in histogram documentation
tracing: Use swap macro in update_max_tr
softirq: Reorder trace_softirqs_on to prevent lockdep splat
tracing: Check for no filter when processing event filters
|
|
Make sure that RQF_TIMED_OUT is cleared when a request is reused
after a block driver timeout handler has returned BLK_EH_DONE.
Fixes: da6612673988 ("blk-mq: don't time out requests again that are in the timeout handler")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Andrew Randrianasulu <randrianasulu@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- a fix for hugetlb with 4K pages, broken by our recent changes for
split PMD PTL.
- set the correct assembler machine type on e500mc, needed since
binutils 2.26 introduced two forms for the "wait" instruction.
- a fix for potential missed TLB flushes with MADV_[FREE|DONTNEED] etc.
and THP on Power9 Radix.
- three fixes to try and make our panic handling more robust by hard
disabling interrupts, and not marking stopped CPUs as offline because
they haven't been properly offlined.
- three other minor fixes.
Thanks to: Aneesh Kumar K.V, Michael Jeanson, Nicholas Piggin.
* tag 'powerpc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm/hash/4k: Free hugetlb page table caches correctly.
powerpc/64s/radix: Fix radix_kvm_prefetch_workaround paca access of not possible CPU
powerpc/64s: Fix build failures with CONFIG_NMI_IPI=n
powerpc/64: hard disable irqs on the panic()ing CPU
powerpc: smp_send_stop do not offline stopped CPUs
powerpc/64: hard disable irqs in panic_smp_self_stop
powerpc/64s: Fix DT CPU features Power9 DD2.1 logic
powerpc/64s/radix: Fix MADV_[FREE|DONTNEED] TLB flush miss problem with THP
powerpc/e500mc: Set assembler machine type to e500mc
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- clear buffers allocated with FORCE_CONTIGUOUS explicitly until the
CMA code honours __GFP_ZERO
- notrace annotation for secondary_start_kernel()
- use early_param() instead of __setup() for "kpti=" as it is needed
for the cpufeature callback remapping swapper to non-global mappings
- ensure writes to swapper are ordered wrt subsequent cache maintenance
in the kpti non-global remapping code
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: mm: Ensure writes to swapper are ordered wrt subsequent cache maintenance
arm64: kpti: Use early_param for kpti= command-line option
arm64: make secondary_start_kernel() notrace
arm64: dma-mapping: clear buffers allocated with FORCE_CONTIGUOUS flag
|
