| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Presently the HNS driver enables the HNS H/W error interrupts after
the dev initialization is completed. However some exceptions such as
NCSI errors can occur when the network port driver is not loaded
and those errors required reporting to the BMC.
Therefore the firmware enabled all the HNS ras error interrupts
before the driver is loaded. And in some cases, there will be some
H/W errors remained unclear before reboot. Thus the HNS driver needs
to process and recover those hw errors occurred before HNS driver is
initialized.
This patch adds processing of the HNS hw errors(RAS and MSI-X)
which occurred before the driver initialization. For RAS, because
they are enabled by firmware, so we can detect specific bits, then
log and clear them. But for MSI-X which can not be enabled before
open vector0 irq, we can't detect the specific error bits, so we
just write 1 to all interrupt source registers to clear.
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
require reset
HNS does not need to be reset when errors occur in some bits.
However presently the HNAE3_FUNC_RESET is set in this case and
as a result the default_reset is done when these errors are reported.
This patch fix this issue. Also patch does some optimization
in setting the reset level for the error recovery.
Reported-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Presently the error handling code sets the reset level required
for the recovery of the hw errors to the reset framework in the
error_detected AER callback. However the rest_event would be
called later from the slot_reset callback. This can cause issue
of using the wrong reset_level if a high priority reset request
occur before the slot_reset is called.
This patch delays setting of the reset level, required
for the hw errors, to the reset framework until the
slot_reset is called.
Reported-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Shiju Jose <shiju.jose@huawei.com>
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michal Kalderon says:
====================
qed: iWARP fixes
This series contains a few small fixes related to iWARP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default window size is calculated for best performance based
on internal hw buffer sizes. The size differs between the
different chips and modes.
Fixes: 67b40dccc45f ("qed: Implement iWARP initialization, teardown and qp operations")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver needs to assign a lossless traffic class for the MPA ll2
connection to ensure no packets are dropped when returning from the
driver as they will never be re-transmitted by the peer.
Fixes: ae3488ff37dc ("qed: Add ll2 connection for processing unaligned MPA packets")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix uninitialized variable warning by static checker.
Fixes: ae3488ff37dc ("qed: Add ll2 connection for processing unaligned MPA packets")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Destroy QP waits for it's ep object state to be set to CLOSED
before proceeding. ep->state can be updated from a different
context. Add smp_store_release/READ_ONCE to synchronize.
Fixes: fc4c6065e661 ("qed: iWARP implement disconnect flows")
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The acpi_node_get_property_reference() doesn't return ACPI error codes,
it just returns regular negative kernel error codes. This patch doesn't
affect run time, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ruslan Babayev <ruslan@babayev.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current vsock code for removal of socket from the list is both
subject to race and inefficient. It takes the lock, checks whether
the socket is in the list, drops the lock and if the socket was on the
list, deletes it from the list. This is subject to race because as soon
as the lock is dropped once it is checked for presence, that condition
cannot be relied upon for any decision. It is also inefficient because
if the socket is present in the list, it takes the lock twice.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski says:
====================
nfp: add two user friendly errors
This small series adds two error messages based on recent
bug reports which turned out not to be bugs..
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Users sometimes mistakenly try to manually bind the PF driver
to the VFs, print a warning message in that case.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Apparently there are still cards in the wild with a very old
management FW. Let's make the error message in that case
indicate more clearly that management firmware has to be
updated.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Robert Hancock says:
====================
Microchip KSZ driver enhancements
A couple of enhancements to the Microchip KSZ switch driver: one to add
PHY register settings for errata workarounds for more stable operation, and
another to add a device tree option to change the output clock rate as
required by some board designs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ9477 series chips have a SYNCLKO pin which by default outputs a
25MHz clock, but some board setups require a 125MHz clock instead. Added
a microchip,synclko-125 device tree property to allow indicating a
125MHz clock output is required.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Silicon Errata and Data Sheet Clarification documents for the
KSZ9477 series of chips describe a number of otherwise undocumented PHY
register settings which are required to work around various chip errata.
Apply these settings when initializing the PHY ports on these chips.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch stmmac_mdio_reset to use GPIO descriptors. GPIO core handles the
"snps,reset-gpio" for GPIO descriptors so we don't need to take care of
it inside the driver anymore.
The advantage of this is that we now preserve the GPIO flags which are
passed via devicetree. This is required on some newer Amlogic boards
which use an Open Drain pin for the reset GPIO. This pin can only output
a LOW signal or switch to input mode but it cannot output a HIGH signal.
There are already devicetree bindings for these special cases and GPIO
core already takes care of them but only if we use GPIO descriptors
instead of GPIO numbers.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eric Dumazet says:
====================
net/packet: better behavior under DDOS
Using tcpdump (or other af_packet user) on a busy host can lead to
catastrophic consequences, because suddenly, potentially all cpus
are spinning on a contended spinlock.
Both packet_rcv() and tpacket_rcv() grab the spinlock
to eventually find there is no room for an additional packet.
This patch series align packet_rcv() and tpacket_rcv() to both
check if the queue is full before grabbing the spinlock.
If the queue is full, they both increment a new atomic counter
placed on a separate cache line to let readers drain the queue faster.
There is still false sharing on this new atomic counter,
we might in the future make it per cpu if there is interest.
====================
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two places where we want to clear the pressure
if possible, add a helper to make it more obvious.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Willem de Bruijn <willemb@google.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__packet_rcv_has_room() can now be run without lock being held.
po->pressure is only a non persistent hint, we can mark
all read/write accesses with READ_ONCE()/WRITE_ONCE()
to document the fact that the field could be written
without any synchronization.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tpacket_rcv() can be hit under DDOS quite hard, since
it will always grab a socket spinlock, to eventually find
there is no room for an additional packet.
Using tcpdump [1] on a busy host can lead to catastrophic consequences,
because of all cpus spinning on a contended spinlock.
This replicates a similar strategy used in packet_rcv()
[1] Also some applications mistakenly use af_packet socket
bound to ETH_P_ALL only to send packets.
Receive queue is never drained and immediately full.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under DDOS, we want to be able to increment tp_drops without
touching the spinlock. This will help readers to drain
the receive queue slightly faster :/
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Goal is use the helper without lock being held.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Goal is to be able to use __tpacket_v3_has_room() without holding
a lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Goal is to be able to use __tpacket_has_room() without holding a lock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct packet_sock is only read.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit "net: phy: Add detection of 1000BaseX link mode support" added
support for not filtering out 1000BaseX mode from the PHY's supported
modes in genphy_config_init, but we have to make a similar change in
genphy_read_abilities in order to actually detect it as a supported mode
in the first place. Add this in.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only for consistency reasons, do it like in main cpsw.c module
and use ndev reference but not by means of slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to set ndev for drvdata when mainly cpsw reference is needed,
so correct this legacy decision.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Paolo Abeni says:
====================
net/mlx5: use indirect call wrappers
The mlx5_core driver uses several indirect calls in fast-path, some of them
are invoked on each ingress packet, even for the XDP-only traffic.
This series leverage the indirect call wrappers infrastructure the avoid
the expansive RETPOLINE overhead for 2 indirect calls in fast-path.
Each call is addressed on a different patch, plus we need to introduce a couple
of additional helpers to cope with the higher number of possible direct-call
alternatives.
v2 -> v3:
- do not add more INDIRECT_CALL_* macros
- use only the direct calls always available regardless of
the mlx5 build options in the last patch
v1 -> v2:
- update the direct call list and use a macro to define it,
as per Saeed suggestion. An intermediated additional
macro is needed to allow arg list expansion
- patch 2/3 is unchanged, as the generated code looks better this way than
with possible alternative (dropping BP hits)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can avoid another indirect call per packet wrapping the rx
handler call with the proper helper.
To ensure that even the last listed direct call experience
measurable gain, despite the additional conditionals we must
traverse before reaching it, I tested reversing the order of the
listed options, with performance differences below noise level.
Together with the previous indirect call patch, this gives
~6% performance improvement in raw UDP tput.
v2 -> v3:
- use only the direct calls always available regardless of
the mlx5 build options
- drop the direct call list macro, to keep the code as simple
as possible for future rework
v1 -> v2:
- update the direct call list and use a macro to define it,
as per Saeed suggestion. An intermediated additional
macro is needed to allow arg list expansion
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can avoid an indirect call per packet wrapping the skb creation
with the appropriate helper.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use extack error reporting mechanism in addition to returning -EINVAL
NL_SET_ERR_* code shamelessy copy/paste/adjusted from act_pedit &
sch_cake and used as reference as to what I should have done in the
first place.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, there is no need to store the individual debugfs file name, just
remove the whole directory all at once, saving a local variable.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guillaume Nault <g.nault@alphalink.fr>
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
r8169: add and use helper rtl_is_8168evl_up
Few registers have been added or changed its purpose with version
RTL8168e-vl, so create a helper for identifying chip versions from
RTL8168e-vl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From RTL8168e-vl the value in register MaxTxPacketSize is interpreted
differently, therefore use new helper rtl_is_8168evl_up to set this
register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper rtl_is_8168evl_up to make the code better readable and to
simplify it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the offchannel TX wait time expires, send the appropriate event.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
cfg80211_remain_on_channel_expired is used to notify userspace when
the remain on channel duration expired by sending an event. There is
no such equivalent to CMD_FRAME, where if offchannel and a duration
is provided, the card will go offchannel for that duration. Currently
there is no way for userspace to tell when that duration expired
apart from setting an independent timeout. This timeout is quite
erroneous as the kernel may not immediately send out the frame
because of scheduling or work queue delays. In testing, it was found
this timeout had to be quite large to accomidate any potential delays.
A better solution is to have the kernel send an event when this
duration has expired. There is already NL80211_CMD_FRAME_WAIT_CANCEL
which can be used to cancel a NL80211_CMD_FRAME offchannel. Using this
command matches perfectly to how NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL
works, where its both used to cancel and notify if the duration has
expired.
Signed-off-by: James Prestwood <james.prestwood@linux.intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This appears to happen occasionally, and if it does we
really want even more information than we have now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If HW advertises it has rate control, we skip all of the
rate control assignments, but sometimes the data we have
here is useful, especially so that we don't have to do
the lookups again on which rates are configured and are
supported.
So do the low rate assignment anyway to help out drivers
that might need it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Even if we have a station, we currently call rate_control_send_low()
with the NULL station unless further rate control (driver, minstrel)
has been initialized.
Change this so we can use more information about the station to use
a better rate. For example, when we associate with an AP, we will
now use the lowest rate it advertised as supported (that we can)
rather than the lowest mandatory rate. This aligns our behaviour
with most other 802.11 implementations.
To make this possible, we need to also ensure that we have non-zero
rates at all times, so in case we really have *nothing* pre-fill
the supp_rates bitmap with the very lowest mandatory bitmap (11b
and 11a on 2.4 and 5 GHz respectively).
Additionally, hostapd appears to be giving us an empty supported
rates bitmap (it can and should do better, since the STA must have
supported for at least the basic rates in the BSS), so ignore any
such bitmaps that would actually zero out the supp_rates, and in
that case just keep the pre-filled mandatory rates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the "OBSS Narrow Bandwidth RU In OFDMA Tolerance Support" flag
definition to the definitions of the flags covered by the Extended
Capability IE.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a function that iterates over the BSS entries associated with a
given wiphy and calls a callback for each iterated BSS. This can be
used by drivers in various ways, e.g., to evaluate some property for
all the BSSs in the medium.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow the userland daemon to en/disable TWT support for an AP.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
[simplify parsing code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Turn TWT for STA interfaces when they associate and/or receive a
beacon where the twt_responder bit has changed.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
