Age | Commit message (Collapse) | Author | Files | Lines |
|
access-controllers is an optional property that allows a peripheral to
refer to one or more domain access controller(s).
Description of this property is added to all peripheral binding files of
the peripheral under the STM32 firewall controller. It allows an accurate
representation of the hardware, where various peripherals are connected
to a firewall bus. The firewall can then check the peripheral accesses
before allowing its device to probe.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The OV7251 sensor only has a single data lane, so 2 entries is not valid.
Fix this to be 1 entry as the schema specifies.
The schema validation doesn't catch this currently due to some limitations
in handling of arrays vs. matrices, but a fix is being worked on.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andi.shyti/linux into i2c/for-mergewindow
Théo adds support for the Mobileye EyeQ5-I2C in the bindings.
This patch is followed by eight commits featuring improvements to
the Nomadik controller, such as simplification of the IRQ logic,
renaming of the private data structure, more efficient use of
FIELD_PREP/GET, GENMASK, etc., better time measurement with
ktime, and more.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Add cleanup.h based auto release of struct device_node pointers via
__free marking and new for_each_child_of_node_scoped() iterator to
use it.
- Always create a base skeleton DT when CONFIG_OF is enabled. This
supports several usecases of adding DT data on non-DT booted
systems.
- Move around some /reserved-memory code in preparation for further
improvements
- Add a stub for_each_property_of_node() for !OF
- Adjust the printk levels on some messages
- Fix __be32 sparse warning
- Drop RESERVEDMEM_OF_DECLARE usage from Freescale qbman driver
(currently orphaned)
- Add Saravana Kannan and drop Frank Rowand as DT maintainers
DT bindings:
- Convert Mediatek timer, Mediatek sysirq, fsl,imx6ul-tsc,
fsl,imx6ul-pinctrl, Atmel AIC, Atmel HLCDC, FPGA region, and
xlnx,sd-fec to DT schemas
- Add existing, but undocumented fsl,imx-anatop binding
- Add bunch of undocumented vendor prefixes used in compatible
strings
- Drop obsolete brcm,bcm2835-pm-wdt binding
- Drop obsolete i2c.txt which as been replaced with schema in
dtschema
- Add DPS310 device and sort trivial-devices.yaml
- Enable undocumented compatible checks on DT binding examples
- More QCom maintainer fixes/updates
- Updates to writing-schema.rst and DT submitting-patches.rst to
cover some frequent review comments
- Clean-up SPDX tags to use 'OR' rather than 'or'"
* tag 'devicetree-for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: soc: imx: fsl,imx-anatop: add imx6q regulators
of: unittest: Use for_each_child_of_node_scoped()
of: Introduce for_each_*_child_of_node_scoped() to automate of_node_put() handling
of: Add cleanup.h based auto release via __free(device_node) markings
of: Move all FDT reserved-memory handling into of_reserved_mem.c
of: Add KUnit test to confirm DTB is loaded
of: unittest: treat missing of_root as error instead of fixing up
x86/of: Unconditionally call unflatten_and_copy_device_tree()
um: Unconditionally call unflatten_device_tree()
of: Create of_root if no dtb provided by firmware
of: Always unflatten in unflatten_and_copy_device_tree()
dt-bindings: timer: mediatek: Convert to json-schema
dt-bindings: interrupt-controller: fsl,intmux: Include power-domains support
soc: fsl: qbman: Remove RESERVEDMEM_OF_DECLARE usage
dt-bindings: fsl-imx-sdma: fix HDMI audio index
dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6
dt-bindings: soc: imx: fsl,imx-anatop: add binding
dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML
dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML
of: make for_each_property_of_node() available to to !OF
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Minor changes to the I2C core. Most changes are in drivers:
The i801 and designware drivers received most of the changes,
including refactorings and some additions.
Recovery changes for the iMX and iMX-LPI2C are now utilizing the
generic i2c support.
The Cadence driver now supports system suspend and resume.
The hisi, mpc, sh_mobile, and npcm drivers have undergone some
cleanups and improvements. Meanwhile, Uwe continues his work on
converting the "remove" callback to become a void function.
The pca954x mux driver now supports additional configurations, such as
isolating faulty channels and flushing stuck buses, among others.
Support has been added for Renesas r8a779h0, i.MX95 LPI2C, and
Microchip sam9x7. Meanwhile, Geert lays the groundwork for the
upcoming R-Car Gen4"
* tag 'i2c-for-6.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: sprd: Convert to platform remove callback returning void
Documentation: i2c: Document that client auto-detection is a legacy mechanism
i2c: remove redundant condition
i2c: rcar: Prepare for the advent of ARCH_RCAR_GEN4
i2c: imx-lpi2c: add generic GPIO recovery for LPI2C
i2c: cadence: Add system suspend and resume PM support
i2c: mpc: remove outdated macro
i2c: mpc: use proper binding for transfer timeouts
dt-bindings: i2c: mpc: use proper binding for transfer timeouts
i2c: smbus: Prepare i2c_register_spd for usage on muxed segments
i2c: constify the struct device_type usage
i2c: designware: Implement generic polling mode code for Wangxun 10Gb NIC
i2c: designware: Fix RX FIFO depth define on Wangxun 10Gb NIC
i2c: designware: Move interrupt handling functions before i2c_dw_xfer()
i2c: designware: Use accessors to DW_IC_INTR_MASK register
i2c: designware: Do not enable interrupts shortly in polling mode
i2c: designware: Uniform initialization flow for polling mode
dt-bindings: i2c: at91: Add sam9x7 compatible string
dt-bindings: i2c: imx-lpi2c: add i.MX95 LPI2C
i2c: Remove redundant comparison in npcm_i2c_reg_slave
...
|
|
Add EyeQ5 bindings to the existing Nomadik I2C dt-bindings. Add the
EyeQ5-specific property behind a conditional. Add an example for this
compatible.
Signed-off-by: Théo Lebrun <theo.lebrun@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
"i2c-scl-clk-low-timeout-us" has flaws in itself and the usage here is
all wrong. The driver doesn't use it as a maximum time for clock
stretching but the maximum time for a total transfer. We already have
a binding for the latter. Convert the wrong binding from examples.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Everything in i2c.txt is covered by schemas/i2c/i2c-controller.yaml in
dtschema project, so remove i2c.txt and update links to it in the tree.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20240222174343.3482354-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add compatible string for sam9x7.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add i.MX95 LPI2C compatible entry, same as i.MX93 compatible
with i.MX7ULP.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. "i2c-parent" is
the former and needs to constrain each entry to a single phandle value.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240124190552.1551929-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The I2C de-mux is different than an I2C mux, so i2c-mux.yaml is not
relevant and shouldn't be referenced.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240124190552.1551929-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Document support for the I2C Bus Interfaces in the Renesas R-Car V4M
(R8A779H0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Maxim Max7357 has a configuration register to enable additional
features. These features aren't enabled by default & its up to
board designer to enable the same as it may have unexpected side effects.
These should be validated for proper functioning & detection of devices
in secondary bus as sometimes it can cause secondary bus being disabled.
Add booleans for:
- maxim,isolate-stuck-channel
- maxim,send-flush-out-sequence
- maxim,preconnection-wiggle-test-enable
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
I never really implemented any filtering on the "+dt" sub-address, so
drop it.
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # for I2C
Link: https://lore.kernel.org/r/20240122211528.1719994-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add google,gs101-hsi2c dedicated compatible for representing
I2C of Google GS101 SoC.
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20240119111132.1290455-3-tudor.ambarus@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"This removes the currently unused CLASS_DDC support (controllers set
the flag, but there is no client to use it).
Also, CLASS_SPD support gets simplified to prepare removal in the
future. Class based instantiation is not recommended these days
anyhow.
Furthermore, I2C core now creates a debugfs directory per I2C adapter.
Current bus driver users were converted to use it.
Finally, quite some driver updates. Standing out are patches for the
wmt-driver which is refactored to support more variants.
This is the rebased pull request where a large series for the
designware driver was dropped"
* tag 'i2c-for-6.8-rc1-rebased' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
MAINTAINERS: use proper email for my I2C work
i2c: stm32f7: add support for stm32mp25 soc
i2c: stm32f7: perform I2C_ISR read once at beginning of event isr
dt-bindings: i2c: document st,stm32mp25-i2c compatible
i2c: stm32f7: simplify status messages in case of errors
i2c: stm32f7: perform most of irq job in threaded handler
i2c: stm32f7: use dev_err_probe upon calls of devm_request_irq
i2c: i801: Add lis3lv02d for Dell XPS 15 7590
i2c: i801: Add lis3lv02d for Dell Precision 3540
i2c: wmt: Reduce redundant: REG_CR setting
i2c: wmt: Reduce redundant: function parameter
i2c: wmt: Reduce redundant: clock mode setting
i2c: wmt: Reduce redundant: wait event complete
i2c: wmt: Reduce redundant: bus busy check
i2c: mux: reg: Remove class-based device auto-detection support
i2c: make i2c_bus_type const
dt-bindings: at24: add ROHM BR24G04
eeprom: at24: use of_match_ptr()
i2c: cpm: Remove linux,i2c-index conversion from be32
i2c: imx: Make SDA actually optional for bus recovering
...
|
|
Add a new compatible st,stm32mp25-i2c for the STM32MP25 series which
has only one interrupt line for both events and errors and differs in
term of handling of FastModePlus.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Tesla FSD is a derivative of Samsung Exynos SoC, thus just like the
others it reuses several devices from older designs. Historically we
kept the old (block's) compatible only. This works fine and there is no
bug here, however guidelines expressed in
Documentation/devicetree/bindings/writing-bindings.rst state that:
1. Compatibles should be specific.
2. We should add new compatibles in case of bugs or features.
Add Tesla FSD compatible specific to be used with an existing fallback.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231205092229.19135-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Samsung Exynos SoC reuses several devices from older designs, thus
historically we kept the old (block's) compatible only. This works fine
and there is no bug here, however guidelines expressed in
Documentation/devicetree/bindings/writing-bindings.rst state that:
1. Compatibles should be specific.
2. We should add new compatibles in case of bugs or features.
Add compatibles specific to each SoC in front of all old-SoC-like
compatibles.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20231108104343.24192-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
Samsung Exynos SoC reuses several devices from older designs, thus
historically we kept the old (block's) compatible only. This works fine
and there is no bug here, however guidelines expressed in
Documentation/devicetree/bindings/writing-bindings.rst state that:
1. Compatibles should be specific.
2. We should add new compatibles in case of bugs or features.
Add compatibles specific to each SoC in front of all old-SoC-like
compatibles.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20231108104343.24192-3-krzysztof.kozlowski@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has largely driver updates for 6.7, i.e. feature additions (like
adding transfers while in atomic mode), using new helpers (like
devm_clk_get_enabled), new IDs, documentation fixes and additions...
you name it.
The core got a memleak fix and better support for nested muxes"
* tag 'i2c-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: s3c2410: make i2c_s3c_irq_nextbyte() void
i2c: qcom-geni: add ACPI device id for sc8180x
Documentation: i2c: add fault code for not supporting 10 bit addresses
i2c: sun6i-p2wi: Prevent potential division by zero
i2c: mux: demux-pinctrl: Convert to use sysfs_emit_at() API
i2c: i801: Use new helper acpi_use_parent_companion
ACPI: Add helper acpi_use_parent_companion
MAINTAINERS: add YAML file for i2c-demux-pinctrl
i2c: core: fix lockdep warning for sparsely nested adapter chain
i2c: axxia: eliminate kernel-doc warnings
dt-bindings: i2c: i2c-demux-pinctrl: Convert to json-schema
i2c: stm32f7: Use devm_clk_get_enabled()
i2c: stm32f4: Use devm_clk_get_enabled()
i2c: stm32f7: add description of atomic in struct stm32f7_i2c_dev
i2c: fix memleak in i2c_new_client_device()
i2c: exynos5: Calculate t_scl_l, t_scl_h according to i2c spec
i2c: i801: Simplify class-based client device instantiation
i2c: exynos5: add support for atomic transfers
i2c: at91-core: Use devm_clk_get_enabled()
eeprom: at24: add ST M24C64-D Additional Write lockable page support
...
|
|
Convert the pinctrl-based I2C bus demultiplexer Device Tree binding
documentation to json-schema.
Update the example to match reality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
This reverts commit ae2a1f0f2cb52e15cf45508f499fcbfd6637bc56. An updated
series was sent. And this patch was not needed anymore because another
compatible entry was reused.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add sc8280xp compatible consistent with recent CAMSS CCI interfaces.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
[wsa: rebased]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Document the compatible for the CCI block found on SC7280 SoC.
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Running 'make dtbs_check DT_SCHEMA_FILES=i2c-mxs.yaml' throws
several schema warnings such as:
imx28-m28evk.dtb: i2c@80058000: '#address-cells', '#size-cells', 'codec@a', 'eeprom@51', 'rtc@68' do not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/i2c/i2c-mxs.yaml#
Fix these warnings by passing a reference to i2c-controller.yaml#
and using 'unevaluatedProperties: false' just like the yaml bindings
of other I2C controllers.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull more devicetree updates from Rob Herring:
"A couple of conversions which didn't get picked up by the subsystems
and one fix:
- Convert st,stih407-irq-syscfg and Omnivision OV7251 bindings to DT
schema
- Merge Omnivision OV5695 into OV5693 binding
- Fix of_overlay_fdt_apply prototype when !CONFIG_OF_OVERLAY"
* tag 'devicetree-fixes-for-6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: irqchip: convert st,stih407-irq-syscfg to DT schema
media: dt-bindings: Convert Omnivision OV7251 to DT schema
media: dt-bindings: Merge OV5695 into OV5693 binding
of: overlay: Fix of_overlay_fdt_apply prototype when !CONFIG_OF_OVERLAY
|
|
Convert the OmniVision OV7251 Image Sensor binding to DT schema format.
vddd-supply was listed as required, but the example and actual user
don't have it. Also, the data brief says it has an internal regulator,
so perhaps it is truly optional.
Add missing common "link-frequencies" which is used and required by the
Linux driver.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Link: https://lore.kernel.org/r/20230817202713.2180195-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has mainly cleanups this time and a few driver improvements.
Because a lot of developers were on holidays (including myself) it was
a good timing to apply lots of cleanups which would normally cause
merge conflicts with other floating patches. Extra thanks go to Andi
Shyti who backed me up when I was on a four week hiatus. This is also
the reason that some patches were commited later than ideal"
* tag 'i2c-for-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (67 commits)
i2c: at91: Use dev_err_probe() instead of dev_err()
I2C: ali15x3: Do PCI error checks on own line
i2c: Make return value check more accurate and explicit for devm_pinctrl_get()
i2c: designware: Add support for recovery when GPIO need pinctrl
i2c: mlxcpld: Add support for extended transaction length
i2c: mlxcpld: Allow driver to run on ARM64 architecture
i2c: nforce2: Do PCI error check on own line
i2c: sis5595: Do PCI error checks on own line
i2c: qcom-cci: Fix error checking in cci_probe()
i2c: muxes: pca954x: Add regulator support
i2c: muxes: pca954x: Add MAX735x/MAX736x support
dt-bindings: i2c: Add Maxim MAX735x/MAX736x variants
dt-bindings: i2c: pca954x: Correct interrupt support
i2c: pnx: Use devm_platform_get_and_ioremap_resource()
i2c: pxa: Use devm_platform_get_and_ioremap_resource()
i2c: s3c2410: Use devm_platform_get_and_ioremap_resource()
i2c: sh_mobile: Use devm_platform_get_and_ioremap_resource()
i2c: st: Use devm_platform_get_and_ioremap_resource()
i2c: qcom-geni: Convert to devm_platform_ioremap_resource()
i2c: stm32f4: Use devm_platform_get_and_ioremap_resource()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new i2c drivers: ds90ub913, ds90ub953, ds90ub960, dw9719, ds90ub913
- new Intel IVSC MEI drivers
- some Mediatek platform drivers were moved to a common location
- Intel atomisp2 driver is now working with the main ov2680 driver. Due
to that, the atomisp2 ov2680 staging one was removed
- the bttv driver was finally converted to videobuf2 framework. This
was the last one upstream using videobuf version 1 core. We'll likely
remove the old videobuf framework on 6.7
- lots of improvements at atomisp driver: it now works with normal I2C
sensors. Several compile-mode dependecies to select between ISP2400
and ISP2401 are now solved in runtime
- a new ipu-bridge logic was added to work with IVSC MEI drivers
- venus driver gained better support for new VPU versions
- the v4l core async framework has gained lots of improvements and
cleanups
- lots of other cleanups, improvements and driver fixes
* tag 'media/v6.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (358 commits)
media: ivsc: Add ACPI dependency
media: bttv: convert to vb2
media: bttv: use audio defaults for winfast2000
media: bttv: refactor bttv_set_dma()
media: bttv: move vbi_skip/vbi_count out of buffer
media: bttv: remove crop info from bttv_buffer
media: bttv: remove tvnorm field from bttv_buffer
media: bttv: remove format field from bttv_buffer
media: bttv: move do_crop flag out of bttv_fh
media: bttv: copy vbi_fmt from bttv_fh
media: bttv: copy vid fmt/width/height from fh
media: bttv: radio use v4l2_fh instead of bttv_fh
media: bttv: replace BUG with WARN_ON
media: bttv: use video_drvdata to get bttv
media: i2c: rdacm21: Fix uninitialized value
media: coda: Remove duplicated include
media: vivid: fix the racy dev->radio_tx_rds_owner
media: i2c: ccs: Check rules is non-NULL
media: i2c: ds90ub960: Fix PLL config for 1200 MHz CSI rate
media: i2c: ds90ub953: Fix use of uninitialized variables
...
|
|
Update the pca954x bindings to add support for the Maxim MAX735x/MAX736x
chips. The functionality will be provided by the existing pca954x driver.
For chips that are powered off by default add a regulator called vdd-supply.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Only some of the PCA954x compatible ICs have interrupt
capability, but the binding advertises it on all ICs.
Sync the dt-binding with the driver and only advertise it on:
- nxp,pca9542
- nxp,pca9543
- nxp,pca9544
- nxp,pca9545
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Fix typos in Documentation/devicetree/bindings. The changes are in
descriptions or comments where they shouldn't affect functionality.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20230814212822.193684-3-helgaas@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
ZynqMP Cadence I2c IP core has own power domain that's why describe it as
optional property.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/8774dba53cae5508f9f7aa173fbaf814d97898b1.1691047405.git.michal.simek@amd.com
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Convert the bindings for GPIO-based I2C Arbitration Using a Challenge &
Response Mechanism to DT schema.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230731163833.319258-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Convert the bindings for NXP PCA9541 I2C bus master selector to DT
schema.
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Peter Rosin <peda@axentia.se>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230731163833.319258-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
Add bindings for I2C Address Translator. Only one property is added,
'i2c-alias-pool', which can be used in the bindings for the device that
supports ATR.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The biggest change this time is for the 32-bit devicetree files, which
are all moved to a new location, using separate subdirectories for
each SoC vendor, following the same scheme that is used on arm64, mips
and riscv. This has been discussed for many years, but so far we never
did this as there was a plan to move the files out of the kernel
entirely, which has never happened.
The impact of this will be that all external patches no longer apply,
and anything depending on the location of the dtb files in the build
directory will have to change. The installed files after 'make
dtbs_install' keep the current location.
There are six added SoCs here that are largely variants of previously
added chips. Two other chips are added in a separate branch along with
their device drivers.
- The Samsung Exynos 4212 makes its return after the Samsung Galaxy
Express phone is addded at last. The SoC support was originally
added in 2012 but removed again in 2017 as it was unused at the
time.
- Amlogic C3 is a Cortex-A35 based smart IP camera chip
- Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
the still common MSM8916 (Snapdragon 410) phone chip that has been
supported for a long time.
- Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
laptop chips, used in the Lenovo Flex 5G, which is added along with
the reference board.
- Qualcomm SDX75 is the latest generation modem chip that is used as
a peripherial in phones but can also run a standalone Linux. Unlike
the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.
- Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
Xuantie C910 core, a step up from all previously added rv64 chips.
All of the above come with reference board implementations, those
included there are 39 new board files, but only five more 32-bit this
time, probably a new low:
- Marantec Maveo board based on dhcor imx6ull module
- Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip
- Epson Moverio BT-200 AR glasses based on TI OMAP4
- PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM
- ICnova ADB4006 board based on Allwinner A20
On the 64-bit side, there are also fewer addded machines than we had
in the recent releases:
- Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.
- NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234
- Qualcomm gains support for 6 reference boards on various members of
their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
of the various reference platforms for their new chips.
- Rockchips support for several newer boards: Indiedroid Nova
(rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
Fastrhino R66S/R68S (rk3568)
- TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
Verdin family with AM62 COM, carrier and dev boards
Other changes to existing boards contain the usual minor improvements
along with
- continued updates to clean up dts files based on dtc warnings and
binding checks, in particular cache properties and node names
- support for devicetree overlays on at91, bcm283x
- significant additions to existing SoC support on mediatek,
qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
STM32MP1
As usual, a lot more detail is available in the individual merge
commits"
* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
ARM: mvebu: fix unit address on armada-390-db flash
ARM: dts: Move .dts files to vendor sub-directories
kbuild: Support flat DTBs install
ARM: dts: Add .dts files missing from the build
ARM: dts: allwinner: Use quoted #include
ARM: dts: lan966x: kontron-d10: add PHY interrupts
ARM: dts: lan966x: kontron-d10: fix SPI CS
ARM: dts: lan966x: kontron-d10: fix board reset
ARM: dts: at91: Enable device-tree overlay support for AT91 boards
arm: dts: Enable device-tree overlay support for AT91 boards
arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
ARM: dts: at91: use generic name for shutdown controller
ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
dt-bindings: firmware: brcm,kona-smc: convert to YAML
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
...
|
|
"regstep" may be deprecated, but it still needs a type.
Fixes: 8ad69f490516 ("dt-bindings: i2c: convert ocores binding to yaml")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Acked-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
@xilinx.com is still working but better to switch to new amd.com after
AMD/Xilinx acquisition.
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Damien Le Moal <dlemoal@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/f5b2bd1e78407e4128fc8f0b5874ba723e710a88.1684245058.git.michal.simek@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull more i2c updates from Wolfram Sang:
"Some more driver bugfixes and a DT binding conversion"
* tag 'i2c-for-6.4-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
dt-bindings: i2c: brcm,kona-i2c: convert to YAML
i2c: gxp: fix build failure without CONFIG_I2C_SLAVE
i2c: imx-lpi2c: avoid taking clk_prepare mutex in PM callbacks
i2c: omap: Fix standard mode false ACK readings
i2c: tegra: Fix PEC support for SMBUS block read
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Add Conor Dooley as a DT binding maintainer
- Swap the order of parsing /memreserve/ and /reserved-memory nodes so
that the /reserved-memory nodes which have more information are
handled first
- Fix some property dependencies in riscv,pmu binding
- Update maintainers entries on a couple of bindings
* tag 'devicetree-fixes-for-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
MAINTAINERS: add Conor as a dt-bindings maintainer
dt-bindings: perf: riscv,pmu: fix property dependencies
dt-bindings: xilinx: Remove Naga from memory and mtd bindings
of: fdt: Scan /memreserve/ last
dt-bindings: clock: r9a06g032-sysctrl: Change maintainer to Fabrizio Castro
dt-bindings: pinctrl: renesas,rzv2m: Change maintainer to Fabrizio Castro
dt-bindings: pinctrl: renesas,rzn1: Change maintainer to Fabrizio Castro
dt-bindings: i2c: renesas,rzv2m: Change maintainer to Fabrizio Castro
|
|
Changes during conversion:
- add used, but previously undocumented SoC-specific compatibles
- drop references to SoCs that are not upstream
- add supported clock frequencies
Signed-off-by: Stanislav Jakubek <stano.jakubek@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Mostly fixes for DTs or DT handling this time. And a few driver
bugfixes"
* tag 'i2c-for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (28 commits)
i2c: xiic: xiic_xfer(): Fix runtime PM leak on error path
i2c: cadence: cdns_i2c_master_xfer(): Fix runtime PM leak on error path
i2c: omap: Improve error reporting for problems during .remove()
i2c: cadence: Add reset controller support
dt-bindings: i2c: cadence: Document `resets` property
i2c: mediatek: add support for MT7981 SoC
dt-bindings: i2c: i2c-mt65xx: add MediaTek MT7981 SoC
dt-bindings: i2c: Drop unneeded quotes
i2c: brcmstb: use devm_platform_ioremap_resource_byname()
i2c: cadence: Detect maximum transfer size
i2c: cadence: Allow to specify the FIFO depth
dt-bindings: i2c: cadence: Document `fifo-depth` property
i2c: xiic: Use devm_platform_get_and_ioremap_resource()
i2c: mpc: Use i2c-scl-clk-low-timeout-us i2c property
i2c: mpc: Use of_property_read_u32 instead of of_get_property
dt-bindings: i2c: mpc: Mark "fsl,timeout" as deprecated
i2c: xiic: hide OF related data for COMPILE_TEST
i2c: synquacer: mark OF related data as maybe unused
dt-bindings: i2c: i2c-mt65xx: Add compatible for MT6795 Helio X10
i2c: imx: Simplify using devm_clk_get_enabled()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- Convert Qcom IOMMU, Amlogic timer, Freescale sec-v4.0, Toshiba
TC358764 display bridge, Parade PS8622 display bridge, and Xilinx
FPGA bindings to DT schema format
- Add qdu1000 and sa8775p SoC support to Qcom PDC interrupt
controller
- Add MediaTek MT8365 UART and SYSIRQ bindings
- Add Arm Cortex-A78C and X1C core compatibles
- Add vendor prefix for Novatek
- Remove bindings for stih415, sti416, stid127 platforms
- Drop uneeded quotes in schema files. This is preparation for
yamllint checking quoting for us.
- Add missing (unevaluated|additional)Properties constraints on child
node schemas
- Clean-up schema comments formatting
- Fix I2C and SPI node bus names in schema examples
- Clean-up some display compatibles schema syntax
- Fix incorrect references to lvds.yaml
- Gather all cache controller bindings in a common directory
DT core:
- Convert unittest to new void .remove platform device hook
- kerneldoc fixes for DT address of_pci_range_to_resource/
of_address_to_resource functions"
* tag 'devicetree-for-6.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (46 commits)
dt-bindings: rng: Drop unneeded quotes
dt-bindings: arm/soc: mediatek: Drop unneeded quotes
dt-bindings: soc: qcom: Drop unneeded quotes
dt-bindings: i2c: samsung: Fix 'deprecated' value
dt-bindings: display: Fix lvds.yaml references
dt-bindings: display: simplify compatibles syntax
dt-bindings: display: mediatek: simplify compatibles syntax
dt-bindings: drm/bridge: ti-sn65dsi86: Fix the video-interfaces.yaml references
dt-bindings: timer: Drop unneeded quotes
dt-bindings: interrupt-controller: qcom,pdc: document qcom,qdu1000-pdc
dt-bindings: interrupt-controller: qcom-pdc: add compatible for sa8775p
dt-bindings: reset: remove stih415/stih416 reset
dt-bindings: net: dwmac: sti: remove stih415/sti416/stid127
dt-bindings: irqchip: sti: remove stih415/stih416 and stid127
dt-bindings: iommu: Convert QCOM IOMMU to YAML
dt-bindings: irqchip: ti,sci-inta: Add optional power-domains property
dt-bindings: Add missing (unevaluated|additional)Properties on child node schemas
of: address: Reshuffle to remove forward declarations
of: address: Fix documented return value of of_pci_range_to_resource()
of: address: Document return value of of_address_to_resource()
...
|
|
Phil no longer works for Renesas.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Acked-by: Fabrizio Castro <fabrizio.castro.jz@renesas.com>
Link: https://lore.kernel.org/r/20230426100736.11808-1-chris.paterson2@renesas.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
'deprecated' is a boolean type which should have a value of 'true' rather
than 'yes'.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230418150643.1529895-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The Cadence I2C controller has an external reset that needs to be
de-asserted before the I2C controller can be accessed.
Document the `resets` devicetree property that can be used to describe how
the reset signal is connected.
While the reset signal will always be present in hardware the devicetree
property is kept optional for backwards compatibility with existing systems
that do not specify the reset property and where the reset signal might not
be controlled by operating system.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Add compatible string for the I2C controllers found in the MediaTek
MT7981 SoC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|