Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core & protocols:
- Complete rework of garbage collection of AF_UNIX sockets.
AF_UNIX is prone to forming reference count cycles due to fd
passing functionality. New method based on Tarjan's Strongly
Connected Components algorithm should be both faster and remove a
lot of workarounds we accumulated over the years.
- Add TCP fraglist GRO support, allowing chaining multiple TCP
packets and forwarding them together. Useful for small switches /
routers which lack basic checksum offload in some scenarios (e.g.
PPPoE).
- Support using SMP threads for handling packet backlog i.e. packet
processing from software interfaces and old drivers which don't use
NAPI. This helps move the processing out of the softirq jumble.
- Continue work of converting from rtnl lock to RCU protection.
Don't require rtnl lock when reading: IPv6 routing FIB, IPv6
address labels, netdev threaded NAPI sysfs files, bonding driver's
sysfs files, MPLS devconf, IPv4 FIB rules, netns IDs, tcp metrics,
TC Qdiscs, neighbor entries, ARP entries via ioctl(SIOCGARP), a lot
of the link information available via rtnetlink.
- Small optimizations from Eric to UDP wake up handling, memory
accounting, RPS/RFS implementation, TCP packet sizing etc.
- Allow direct page recycling in the bulk API used by XDP, for +2%
PPS.
- Support peek with an offset on TCP sockets.
- Add MPTCP APIs for querying last time packets were received/sent/acked
and whether MPTCP "upgrade" succeeded on a TCP socket.
- Add intra-node communication shortcut to improve SMC performance.
- Add IPv6 (and IPv{4,6}-over-IPv{4,6}) support to the GTP protocol
driver.
- Add HSR-SAN (RedBOX) mode of operation to the HSR protocol driver.
- Add reset reasons for tracing what caused a TCP reset to be sent.
- Introduce direction attribute for xfrm (IPSec) states. State can be
used either for input or output packet processing.
Things we sprinkled into general kernel code:
- Add bitmap_{read,write}(), bitmap_size(), expose BYTES_TO_BITS().
This required touch-ups and renaming of a few existing users.
- Add Endian-dependent __counted_by_{le,be} annotations.
- Make building selftests "quieter" by printing summaries like
"CC object.o" rather than full commands with all the arguments.
Netfilter:
- Use GFP_KERNEL to clone elements, to deal better with OOM
situations and avoid failures in the .commit step.
BPF:
- Add eBPF JIT for ARCv2 CPUs.
- Support attaching kprobe BPF programs through kprobe_multi link in
a session mode, meaning, a BPF program is attached to both function
entry and return, the entry program can decide if the return
program gets executed and the entry program can share u64 cookie
value with return program. "Session mode" is a common use-case for
tetragon and bpftrace.
- Add the ability to specify and retrieve BPF cookie for raw
tracepoint programs in order to ease migration from classic to raw
tracepoints.
- Add an internal-only BPF per-CPU instruction for resolving per-CPU
memory addresses and implement support in x86, ARM64 and RISC-V
JITs. This allows inlining functions which need to access per-CPU
state.
- Optimize x86 BPF JIT's emit_mov_imm64, and add support for various
atomics in bpf_arena which can be JITed as a single x86
instruction. Support BPF arena on ARM64.
- Add a new bpf_wq API for deferring events and refactor
process-context bpf_timer code to keep common code where possible.
- Harden the BPF verifier's and/or/xor value tracking.
- Introduce crypto kfuncs to let BPF programs call kernel crypto
APIs.
- Support bpf_tail_call_static() helper for BPF programs with GCC 13.
- Add bpf_preempt_{disable,enable}() kfuncs in order to allow a BPF
program to have code sections where preemption is disabled.
Driver API:
- Skip software TC processing completely if all installed rules are
marked as HW-only, instead of checking the HW-only flag rule by
rule.
- Add support for configuring PoE (Power over Ethernet), similar to
the already existing support for PoDL (Power over Data Line)
config.
- Initial bits of a queue control API, for now allowing a single
queue to be reset without disturbing packet flow to other queues.
- Common (ethtool) statistics for hardware timestamping.
Tests and tooling:
- Remove the need to create a config file to run the net forwarding
tests so that a naive "make run_tests" can exercise them.
- Define a method of writing tests which require an external endpoint
to communicate with (to send/receive data towards the test
machine). Add a few such tests.
- Create a shared code library for writing Python tests. Expose the
YAML Netlink library from tools/ to the tests for easy Netlink
access.
- Move netfilter tests under net/, extend them, separate performance
tests from correctness tests, and iron out issues found by running
them "on every commit".
- Refactor BPF selftests to use common network helpers.
- Further work filling in YAML definitions of Netlink messages for:
nftables, team driver, bonding interfaces, vlan interfaces, VF
info, TC u32 mark, TC police action.
- Teach Python YAML Netlink to decode attribute policies.
- Extend the definition of the "indexed array" construct in the specs
to cover arrays of scalars rather than just nests.
- Add hyperlinks between definitions in generated Netlink docs.
Drivers:
- Make sure unsupported flower control flags are rejected by drivers,
and make more drivers report errors directly to the application
rather than dmesg (large number of driver changes from Asbjørn
Sloth Tønnesen).
- Ethernet high-speed NICs:
- Broadcom (bnxt):
- support multiple RSS contexts and steering traffic to them
- support XDP metadata
- make page pool allocations more NUMA aware
- Intel (100G, ice, idpf):
- extract datapath code common among Intel drivers into a library
- use fewer resources in switchdev by sharing queues with the PF
- add PFCP filter support
- add Ethernet filter support
- use a spinlock instead of HW lock in PTP clock ops
- support 5 layer Tx scheduler topology
- nVidia/Mellanox:
- 800G link modes and 100G SerDes speeds
- per-queue IRQ coalescing configuration
- Marvell Octeon:
- support offloading TC packet mark action
- Ethernet NICs consumer, embedded and virtual:
- stop lying about skb->truesize in USB Ethernet drivers, it
messes up TCP memory calculations
- Google cloud vNIC:
- support changing ring size via ethtool
- support ring reset using the queue control API
- VirtIO net:
- expose flow hash from RSS to XDP
- per-queue statistics
- add selftests
- Synopsys (stmmac):
- support controllers which require an RX clock signal from the
MII bus to perform their hardware initialization
- TI:
- icssg_prueth: support ICSSG-based Ethernet on AM65x SR1.0 devices
- icssg_prueth: add SW TX / RX Coalescing based on hrtimers
- cpsw: minimal XDP support
- Renesas (ravb):
- support describing the MDIO bus
- Realtek (r8169):
- add support for RTL8168M
- Microchip Sparx5:
- matchall and flower actions mirred and redirect
- Ethernet switches:
- nVidia/Mellanox:
- improve events processing performance
- Marvell:
- add support for MV88E6250 family internal PHYs
- Microchip:
- add DCB and DSCP mapping support for KSZ switches
- vsc73xx: convert to PHYLINK
- Realtek:
- rtl8226b/rtl8221b: add C45 instances and SerDes switching
- Many driver changes related to PHYLIB and PHYLINK deprecated API
cleanup
- Ethernet PHYs:
- Add a new driver for Airoha EN8811H 2.5 Gigabit PHY.
- micrel: lan8814: add support for PPS out and external timestamp trigger
- WiFi:
- Disable Wireless Extensions (WEXT) in all Wi-Fi 7 devices
drivers. Modern devices can only be configured using nl80211.
- mac80211/cfg80211
- handle color change per link for WiFi 7 Multi-Link Operation
- Intel (iwlwifi):
- don't support puncturing in 5 GHz
- support monitor mode on passive channels
- BZ-W device support
- P2P with HE/EHT support
- re-add support for firmware API 90
- provide channel survey information for Automatic Channel Selection
- MediaTek (mt76):
- mt7921 LED control
- mt7925 EHT radiotap support
- mt7920e PCI support
- Qualcomm (ath11k):
- P2P support for QCA6390, WCN6855 and QCA2066
- support hibernation
- ieee80211-freq-limit Device Tree property support
- Qualcomm (ath12k):
- refactoring in preparation of multi-link support
- suspend and hibernation support
- ACPI support
- debugfs support, including dfs_simulate_radar support
- RealTek:
- rtw88: RTL8723CS SDIO device support
- rtw89: RTL8922AE Wi-Fi 7 PCI device support
- rtw89: complete features of new WiFi 7 chip 8922AE including
BT-coexistence and Wake-on-WLAN
- rtw89: use BIOS ACPI settings to set TX power and channels
- rtl8xxxu: enable Management Frame Protection (MFP) support
- Bluetooth:
- support for Intel BlazarI and Filmore Peak2 (BE201)
- support for MediaTek MT7921S SDIO
- initial support for Intel PCIe BT driver
- remove HCI_AMP support"
* tag 'net-next-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1827 commits)
selftests: netfilter: fix packetdrill conntrack testcase
net: gro: fix napi_gro_cb zeroed alignment
Bluetooth: btintel_pcie: Refactor and code cleanup
Bluetooth: btintel_pcie: Fix warning reported by sparse
Bluetooth: hci_core: Fix not handling hdev->le_num_of_adv_sets=1
Bluetooth: btintel: Fix compiler warning for multi_v7_defconfig config
Bluetooth: btintel_pcie: Fix compiler warnings
Bluetooth: btintel_pcie: Add *setup* function to download firmware
Bluetooth: btintel_pcie: Add support for PCIe transport
Bluetooth: btintel: Export few static functions
Bluetooth: HCI: Remove HCI_AMP support
Bluetooth: L2CAP: Fix div-by-zero in l2cap_le_flowctl_init()
Bluetooth: qca: Fix error code in qca_read_fw_build_info()
Bluetooth: hci_conn: Use __counted_by() and avoid -Wfamnae warning
Bluetooth: btintel: Add support for Filmore Peak2 (BE201)
Bluetooth: btintel: Add support for BlazarI
LE Create Connection command timeout increased to 20 secs
dt-bindings: net: bluetooth: Add MediaTek MT7921S SDIO Bluetooth
Bluetooth: compute LE flow credits based on recvbuf space
Bluetooth: hci_sync: Use cmd->num_cis instead of magic number
...
|
|
The MediaTek MT7921S is a WiFi/Bluetooth combo chip that works over
SDIO. WiFi and Bluetooth are separate SDIO functions within the chip.
While the Bluetooth SDIO function is fully discoverable, the chip has
a pin that can reset just the Bluetooth core, as opposed to the full
chip. This should be described in the device tree.
Add a device tree binding for the Bluetooth SDIO function of the MT7921S
specifically to document the reset line. This binding is based on the MMC
controller binding, which specifies one device node per SDIO function.
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
CYW43439 is a Wi-Fi + Bluetooth combo device from Infineon.
The Bluetooth part is capable of Bluetooth 5.2 BR/EDR/LE .
This chip is present e.g. on muRata 1YN module.
Extend the binding with its DT compatible using fallback
compatible string to "brcm,bcm4329-bt" which seems to be
the oldest compatible device. This should also prevent the
growth of compatible string tables in drivers. The existing
block of compatible strings is retained.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The RZ/N1 series of MPUs feature up to two Gigabit Ethernet controllers.
These controllers are based on Synopsys IPs. They can be connected to
RZ/N1 RGMII/RMII converters.
Add a binding that describes these GMAC devices.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
[rgantois: commit log]
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Romain Gantois <romain.gantois@bootlin.com>
Link: https://lore.kernel.org/r/20240513-rzn1-gmac1-v7-1-6acf58b5440d@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC driver updates from Arnd Bergmann:
"As usual, these are updates for drivers that are specific to certain
SoCs or firmware running on them.
Notable updates include
- The new STMicroelectronics STM32 "firewall" bus driver that is used
to provide a barrier between different parts of an SoC
- Lots of updates for the Qualcomm platform drivers, in particular
SCM, which gets a rewrite of its initialization code
- Firmware driver updates for Arm FF-A notification interrupts and
indirect messaging, SCMI firmware support for pin control and
vendor specific interfaces, and TEE firmware interface changes
across multiple TEE drivers
- A larger cleanup of the Mediatek CMDQ driver and some related bits
- Kconfig changes for riscv drivers to prepare for adding Kanaan k230
support
- Multiple minor updates for the TI sysc bus driver, memory
controllers, hisilicon hccs and more"
* tag 'soc-drivers-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (103 commits)
firmware: qcom: uefisecapp: Allow on sc8180x Primus and Flex 5G
soc: qcom: pmic_glink: Make client-lock non-sleeping
dt-bindings: soc: qcom,wcnss: fix bluetooth address example
soc/tegra: pmc: Add EQOS wake event for Tegra194 and Tegra234
bus: stm32_firewall: fix off by one in stm32_firewall_get_firewall()
bus: etzpc: introduce ETZPC firewall controller driver
firmware: arm_ffa: Avoid queuing work when running on the worker queue
bus: ti-sysc: Drop legacy idle quirk handling
bus: ti-sysc: Drop legacy quirk handling for smartreflex
bus: ti-sysc: Drop legacy quirk handling for uarts
bus: ti-sysc: Add a description and copyrights
bus: ti-sysc: Move check for no-reset-on-init
soc: hisilicon: kunpeng_hccs: replace MAILBOX dependency with PCC
soc: hisilicon: kunpeng_hccs: Add the check for obtaining complete port attribute
firmware: arm_ffa: Fix memory corruption in ffa_msg_send2()
bus: rifsc: introduce RIFSC firewall controller driver
of: property: fw_devlink: Add support for "access-controller"
soc: mediatek: mtk-socinfo: Correct the marketing name for MT8188GV
soc: mediatek: mtk-socinfo: Add entry for MT8395AV/ZA Genio 1200
soc: mediatek: mtk-mutex: Add support for MT8188 VPPSYS
...
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c
35d92abfbad8 ("net: hns3: fix kernel crash when devlink reload during initialization")
2a1a1a7b5fd7 ("net: hns3: add command queue trace for hns3")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The third, and most likely the last, "new features" pull request for
v6.10 with changes both in stack and in drivers. In ath12k and rtw89
we disabled Wireless Extensions just like with iwlwifi earlier. Wi-Fi
7 devices will not support Wireless Extensions (WEXT) anymore so if
someone is still using the legacy WEXT interface it's time to switch
to nl80211 now!
We merged wireless into wireless-next as we decided not to send a
wireless pull request to v6.9 this late in the cycle. Also an
immutable branch with MHI subsystem was merged to get ath11k and
ath12k hibernation working.
Major changes:
mac80211/cfg80211
* handle color change per link
mt76
* mt7921 LED control
* mt7925 EHT radiotap support
* mt7920e PCI support
ath12k
* debugfs support
* dfs_simulate_radar debugfs file
* disable Wireless Extensions
* suspend and hibernation support
* ACPI support
* refactoring in preparation of multi-link support
ath11k
* support hibernation (required changes in qrtr and MHI subsystems)
* ieee80211-freq-limit Device Tree property support
ath10k
* firmware-name Device Tree property support
rtw89
* complete features of new WiFi 7 chip 8922AE including BT-coexistence
and WoWLAN
* use BIOS ACPI settings to set TX power and channels
* disable Wireless Extensios on Wi-Fi 7 devices
iwlwifi
* block_esr debugfs file
* support again firmware API 90 (was reverted earlier)
* provide channel survey information for Automatic Channel Selection (ACS)
* tag 'wireless-next-2024-05-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (214 commits)
wifi: mwl8k: initialize cmd->addr[] properly
wifi: iwlwifi: Ensure prph_mac dump includes all addresses
wifi: iwlwifi: mvm: don't request statistics in restart
wifi: iwlwifi: mvm: exit EMLSR if secondary link is not used
wifi: iwlwifi: mvm: add beacon template version 14
wifi: iwlwifi: mvm: align UATS naming with firmware
wifi: iwlwifi: Force SCU_ACTIVE for specific platforms
wifi: iwlwifi: mvm: record and return channel survey information
wifi: iwlwifi: mvm: add the firmware API for channel survey
wifi: iwlwifi: mvm: Fix race in scan completion
wifi: iwlwifi: mvm: Add a print for invalid link pair due to bandwidth
wifi: iwlwifi: mvm: add a debugfs for reading EMLSR blocking reasons
wifi: iwlwifi: mvm: Add active EMLSR blocking reasons prints
wifi: iwlwifi: bump FW API to 90 for BZ/SC devices
wifi: iwlwifi: mvm: fix primary link setting
wifi: iwlwifi: mvm: use already determined cmd_id
wifi: iwlwifi: mvm: don't reset link selection during restart
wifi: iwlwifi: Print EMLSR states name
wifi: iwlwifi: mvm: Block EMLSR when a p2p/softAP vif is active
wifi: iwlwifi: mvm: fix typo in debug print
...
====================
Link: https://lore.kernel.org/r/20240508120726.85A10C113CC@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Several clocks as well as both sgmiisys phandles were added by mistake
to the Ethernet bindings for MT7988. Also, the total number of clocks
didn't match with the actual number of items listed.
This happened because the vendor driver which served as a reference uses
a high number of syscon phandles to access various parts of the SoC
which wasn't acceptable upstream. Hence several parts which have never
previously been supported (such SerDes PHY and USXGMII PCS) are going to
be implemented by separate drivers. As a result the device tree will
look much more sane.
Quickly align the bindings with the upcoming reality of the drivers
actually adding support for the remaining Ethernet-related features of
the MT7988 SoC.
Fixes: c94a9aabec36 ("dt-bindings: net: mediatek,net: add mt7988-eth binding")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1569290b21cc787a424469ed74456a7e976b102d.1715084326.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a compatible property specific to IPQ9574. This should be used
along with the IPQ4019 compatible. This second compatible serves the
same purpose as the ipq{5,6,8} compatibles. This is to indicate that
the clocks properties are required.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240507024758.2810514-1-mr.nuke.me@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.10
ath12k
* debugfs support
* dfs_simulate_radar debugfs file
* disable Wireless Extensions
* suspend and hibernation support
* ACPI support
* refactoring in preparation of multi-link support
ath11k
* support hibernation (required changes in qrtr and MHI subsystems)
* ieee80211-freq-limit Device Tree property support
ath10k
* firmware-name Device Tree property support
|
|
Strict priority for the tx scheduler is by default in Linux driver, so the
tx-sched-sp property was removed in commit aed6864035b1 ("net: stmmac:
platform: Delete a redundant condition branch").
This property is still in use in the following DT (and it will be removed
in a separate patch series):
- arch/arm64/boot/dts/freescale/imx8mp-beacon-som.dtsi
- arch/arm64/boot/dts/freescale/imx8mp-evk.dts
- arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
- arch/arm64/boot/dts/qcom/sa8540p-ride.dts
- arch/arm64/boot/dts/qcom/sa8775p-ride.dts
There is no problem if that property is still used in the DTs above,
since, as seen above, it is a default property of the driver.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20240429092654.31390-2-f.suligoi@asem.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/drivers
STM32 Firewall bus for v6.10, round 1
Highlights:
---------
Introduce STM32 Firewall framework for STM32MP1x and STM32MP2x
platforms. STM32MP1x(ETZPC) and STM32MP2x(RIFSC) Firewall controllers
register to the framework to offer firewall services such as access
granting.
This series of patches is a new approach on the previous STM32 system
bus, history is available here:
https://lore.kernel.org/lkml/20230127164040.1047583/
The need for such framework arises from the fact that there are now
multiple hardware firewalls implemented across multiple products.
Drivers are shared between different products, using the same code.
When it comes to firewalls, the purpose mostly stays the same: Protect
hardware resources. But the implementation differs, and there are
multiple types of firewalls: peripheral, memory, ...
Some hardware firewall controllers such as the RIFSC implemented on
STM32MP2x platforms may require to take ownership of a resource before
being able to use it, hence the requirement for firewall services to
take/release the ownership of such resources.
On the other hand, hardware firewall configurations are becoming
more and more complex. These mecanisms prevent platform crashes
or other firewall-related incoveniences by denying access to some
resources.
The stm32 firewall framework offers an API that is defined in
firewall controllers drivers to best fit the specificity of each
firewall.
For every peripherals protected by either the ETZPC or the RIFSC, the
firewall framework checks the firewall controlelr registers to see if
the peripheral's access is granted to the Linux kernel. If not, the
peripheral is configured as secure, the node is marked populated,
so that the driver is not probed for that device.
The firewall framework relies on the access-controller device tree
binding. It is used by peripherals to reference a domain access
controller. In this case a firewall controller. The bus uses the ID
referenced by the access-controller property to know where to look
in the firewall to get the security configuration for the peripheral.
This allows a device tree description rather than a hardcoded peripheral
table in the bus driver.
The STM32 ETZPC device is responsible for filtering accesses based on
security level, or co-processor isolation for any resource connected
to it.
The RIFSC is responsible for filtering accesses based on Compartment
ID / security level / privilege level for any resource connected to
it.
* tag 'stm32-bus-firewall-for-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
bus: stm32_firewall: fix off by one in stm32_firewall_get_firewall()
bus: etzpc: introduce ETZPC firewall controller driver
bus: rifsc: introduce RIFSC firewall controller driver
of: property: fw_devlink: Add support for "access-controller"
firewall: introduce stm32_firewall framework
dt-bindings: bus: document ETZPC
dt-bindings: bus: document RIFSC
dt-bindings: treewide: add access-controllers description
dt-bindings: document generic access controllers
Link: https://lore.kernel.org/r/7dc64226-5429-4ab7-a8c8-6053b12e3cf5@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add the TPS23881 I2C Power Sourcing Equipment controller device tree
bindings documentation.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-13-242293fd1900@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the PD692x0 I2C Power Sourcing Equipment controller device tree
bindings documentation.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-11-242293fd1900@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PSE PI setup may encompass multiple PSE controllers or auxiliary circuits
that collectively manage power delivery to one Ethernet port.
Such configurations might support a range of PoE standards and require
the capability to dynamically configure power delivery based on the
operational mode (e.g., PoE2 versus PoE4) or specific requirements of
connected devices. In these instances, a dedicated PSE PI node becomes
essential for accurately documenting the system architecture. This node
would serve to detail the interactions between different PSE controllers,
the support for various PoE modes, and any additional logic required to
coordinate power delivery across the network infrastructure.
The old usage of "#pse-cells" is unsuficient as it carries only the PSE PI
index information.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://lore.kernel.org/r/20240417-feature_poe-v9-8-242293fd1900@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is an existing optional property that ieee80211.yaml/cfg80211
provides. It's useful to further restrict supported frequencies
for a specified device through device-tree.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/fc606d2550d047a53b4289235dd3c0fe23d5daac.1686486468.git.chunkeey@gmail.com
|
|
Allow nvmem-cells and nvmem-cell-names to get mac_address from onchip
fuse.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240415103621.1644735-1-peng.fan@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The dwmac supports specifying the RGMII clock delays, but it is
recommended to use rgmii-id and to specify the delays in the phy node
instead [1].
Change the example accordingly to no longer promote this undesired
setting.
[1] https://lore.kernel.org/all/1a0de7b4-f0f7-4080-ae48-f5ffa9e76be3@lunn.ch/
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Dragan Simic <dsimic@manjaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240408-rockchip-dwmac-rgmii-id-binding-v1-1-3886d1a8bd54@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Silicon Revision 1.0 of the AM65x came with a slightly different ICSSG
support: Only 2 PRUs per slice are available and instead 2 additional
DMA channels are used for management purposes. We have no restrictions
on specified PRUs, but the DMA channels need to be adjusted.
Co-developed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Diogo Ivo <diogo.ivo@siemens.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: MD Danish Anwar <danishanwar@ti.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
access-controllers is an optional property that allows a peripheral to
refer to one or more domain access controller(s).
Description of this property is added to all peripheral binding files of
the peripheral under the STM32 firewall controller. It allows an accurate
representation of the hardware, where various peripherals are connected
to a firewall bus. The firewall can then check the peripheral accesses
before allowing its device to probe.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
For WCN3990 platforms we need to look for the platform / board specific
firmware-N.mbn file which corresponds to the wlanmdsp.mbn loaded to the
modem DSP via the TQFTPserv. Add firmware-name property describing this
classifier.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240306-wcn3990-firmware-path-v2-1-f89e98e71a57@linaro.org
|
|
Add StarFive JH8100 dwmac support.
The JH8100 dwmac shares the same driver code as the JH7110 dwmac
and has only one reset signal.
Please refer to below:
JH8100: reset-names = "stmmaceth";
JH7110: reset-names = "stmmaceth", "ahb";
JH7100: reset-names = "ahb";
Example usage of JH8100 in the device tree:
gmac0: ethernet@16030000 {
compatible = "starfive,jh8100-dwmac",
"starfive,jh7110-dwmac",
"snps,dwmac-5.20";
...
};
Signed-off-by: Tan Chun Hau <chunhau.tan@starfivetech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240403100549.78719-2-chunhau.tan@starfivetech.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/ipv4/ip_gre.c
17af420545a7 ("erspan: make sure erspan_base_hdr is present in skb->head")
5832c4a77d69 ("ip_tunnel: convert __be16 tunnel flags to bitmaps")
https://lore.kernel.org/all/20240402103253.3b54a1cf@canb.auug.org.au/
Adjacent changes:
net/ipv6/ip6_fib.c
d21d40605bca ("ipv6: Fix infinite recursion in fib6_dump_done().")
5fc68320c1fb ("ipv6: remove RTNL protection from inet6_dump_fib()")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi, Stephen has an example
merge resolution which should help with fixing the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
* tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (122 commits)
wifi: mt76: mt7915: workaround dubious x | !y warning
wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warnings
wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warnings
wifi: iwlwifi: mvm: fix check in iwl_mvm_sta_fw_id_mask
net: rfkill: gpio: Convert to platform remove callback returning void
wifi: mac80211: use kvcalloc() for codel vars
wifi: iwlwifi: reconfigure TLC during HW restart
wifi: iwlwifi: mvm: don't change BA sessions during restart
wifi: iwlwifi: mvm: select STA mask only for active links
wifi: iwlwifi: mvm: set wider BW OFDMA ignore correctly
wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD cmd v9
wifi: iwlwifi: mvm: Declare HE/EHT capabilities support for P2P interfaces
wifi: iwlwifi: mvm: Remove outdated comment
wifi: iwlwifi: add support for BZ_W
wifi: iwlwifi: Print a specific device name.
wifi: iwlwifi: remove wrong CRF_IDs
wifi: iwlwifi: remove devices that never came out
wifi: iwlwifi: mvm: mark EMLSR disabled in cleanup iterator
wifi: iwlwifi: mvm: fix active link counting during recovery
wifi: iwlwifi: mvm: assign link STA ID lookups during restart
...
====================
Link: https://lore.kernel.org/r/20240403093625.CF515C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
'snps,priority' is also defined in dma/snps,dw-axi-dmac.yaml as a
uint32-array. It's preferred to have a single type for a given property
name, so update the type in snps,dwmac schema to match.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240401204422.1692359-2-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The bindings for Renesas Ethernet TSN was just merged in v6.9 and the
design for the bindings followed that of other Renesas Ethernet drivers
and thus did not force a child-node for the MDIO bus. As there
are no upstream drivers or users of this binding yet take the
opportunity to correct this and force the usage of a child-node for the
MDIO bus.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240330131228.1541227-1-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Linux kernel dwmac-stm32 driver currently supports three DT
properties used to configure whether PHY clock are generated by
the MAC or supplied to the MAC from the PHY.
Originally there were two properties, st,eth-clk-sel and
st,eth-ref-clk-sel, each used to configure MAC clocking in
different bus mode and for different MAC clock frequency.
Since it is possible to determine the MAC 'eth-ck' clock
frequency from the clock subsystem and PHY bus mode from
the 'phy-mode' property, two disparate DT properties are
no longer required to configure MAC clocking.
Linux kernel commit 1bb694e20839 ("net: ethernet: stmmac: simplify phy modes management for stm32")
introduced a third, unified, property st,ext-phyclk. This property
covers both use cases of st,eth-clk-sel and st,eth-ref-clk-sel DT
properties, as well as a new use case for 25 MHz clock generated
by the MAC.
The third property st,ext-phyclk is so far undocumented,
document it.
Below table summarizes the clock requirement and clock sources for
supported PHY interface modes.
__________________________________________________________________________
|PHY_MODE | Normal | PHY wo crystal| PHY wo crystal |No 125Mhz from PHY|
| | | 25MHz | 50MHz | |
---------------------------------------------------------------------------
| MII | - | eth-ck | n/a | n/a |
| | | st,ext-phyclk | | |
---------------------------------------------------------------------------
| GMII | - | eth-ck | n/a | n/a |
| | | st,ext-phyclk | | |
---------------------------------------------------------------------------
| RGMII | - | eth-ck | n/a | eth-ck |
| | | st,ext-phyclk | | st,eth-clk-sel or|
| | | | | st,ext-phyclk |
---------------------------------------------------------------------------
| RMII | - | eth-ck | eth-ck | n/a |
| | | st,ext-phyclk | st,eth-ref-clk-sel | |
| | | | or st,ext-phyclk | |
---------------------------------------------------------------------------
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Link: https://lore.kernel.org/r/20240328185337.332703-2-christophe.roullier@foss.st.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the Airoha EN8811H 2.5 Gigabit PHY.
The en8811h phy can be set with serdes polarity reversed on rx and/or tx.
Signed-off-by: Eric Woudstra <ericwouds@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240326162305.303598-2-ericwouds@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Several Qualcomm Bluetooth controllers lack persistent storage for the
device address and instead one can be provided by the boot firmware
using the 'local-bd-address' devicetree property.
The Bluetooth bindings clearly states that the address should be
specified in little-endian order, but due to a long-standing bug in the
Qualcomm driver which reversed the address some boot firmware has been
providing the address in big-endian order instead.
The only device out there that should be affected by this is the WCN3991
used in some Chromebooks.
Add a 'qcom,local-bd-address-broken' property which can be set on these
platforms to indicate that the boot firmware is using the wrong byte
order.
Note that ChromeOS always updates the kernel and devicetree in lockstep
so that there is no need to handle backwards compatibility with older
devicetrees.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
The Renesas Ethernet AVB bindings do not allow the MDIO bus to be
described. This has not been needed as only a single PHY is
supported and no MDIO bus properties have been needed.
Add an optional mdio node to the binding which allows the MDIO bus to be
described and allow bus properties to be set.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240325153451.2366083-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DT core:
- Add cleanup.h based auto release of struct device_node pointers via
__free marking and new for_each_child_of_node_scoped() iterator to
use it.
- Always create a base skeleton DT when CONFIG_OF is enabled. This
supports several usecases of adding DT data on non-DT booted
systems.
- Move around some /reserved-memory code in preparation for further
improvements
- Add a stub for_each_property_of_node() for !OF
- Adjust the printk levels on some messages
- Fix __be32 sparse warning
- Drop RESERVEDMEM_OF_DECLARE usage from Freescale qbman driver
(currently orphaned)
- Add Saravana Kannan and drop Frank Rowand as DT maintainers
DT bindings:
- Convert Mediatek timer, Mediatek sysirq, fsl,imx6ul-tsc,
fsl,imx6ul-pinctrl, Atmel AIC, Atmel HLCDC, FPGA region, and
xlnx,sd-fec to DT schemas
- Add existing, but undocumented fsl,imx-anatop binding
- Add bunch of undocumented vendor prefixes used in compatible
strings
- Drop obsolete brcm,bcm2835-pm-wdt binding
- Drop obsolete i2c.txt which as been replaced with schema in
dtschema
- Add DPS310 device and sort trivial-devices.yaml
- Enable undocumented compatible checks on DT binding examples
- More QCom maintainer fixes/updates
- Updates to writing-schema.rst and DT submitting-patches.rst to
cover some frequent review comments
- Clean-up SPDX tags to use 'OR' rather than 'or'"
* tag 'devicetree-for-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (56 commits)
dt-bindings: soc: imx: fsl,imx-anatop: add imx6q regulators
of: unittest: Use for_each_child_of_node_scoped()
of: Introduce for_each_*_child_of_node_scoped() to automate of_node_put() handling
of: Add cleanup.h based auto release via __free(device_node) markings
of: Move all FDT reserved-memory handling into of_reserved_mem.c
of: Add KUnit test to confirm DTB is loaded
of: unittest: treat missing of_root as error instead of fixing up
x86/of: Unconditionally call unflatten_and_copy_device_tree()
um: Unconditionally call unflatten_device_tree()
of: Create of_root if no dtb provided by firmware
of: Always unflatten in unflatten_and_copy_device_tree()
dt-bindings: timer: mediatek: Convert to json-schema
dt-bindings: interrupt-controller: fsl,intmux: Include power-domains support
soc: fsl: qbman: Remove RESERVEDMEM_OF_DECLARE usage
dt-bindings: fsl-imx-sdma: fix HDMI audio index
dt-bindings: soc: imx: fsl,imx-iomuxc-gpr: add imx6
dt-bindings: soc: imx: fsl,imx-anatop: add binding
dt-bindings: input: touchscreen: fsl,imx6ul-tsc convert to YAML
dt-bindings: pinctrl: fsl,imx6ul-pinctrl: convert to YAML
of: make for_each_property_of_node() available to to !OF
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Not a ton of stuff happening in the clk framework. We got some more
devm helpers and we seem to be going in the direction of "just turn
this stuff on already and leave me alone!" with the addition of a
devm_clk_bulk_get_all_enable() API. I'm hoping that we can make that
into a pmdomain that drivers attach instead, but this API should help
drivers simplify in the meantime.
Outside of the devm wrappers, we've got the usual clk driver updates
that are dominated by the major phone SoC vendors (Samsung and
Qualcomm) and the non-critical driver fixes for things like incorrect
topology descriptions and wrong registers or bit fields. More details
are below, but I'd say that it looks pretty ordinary. The only thing
that really jumps out at me is the Renesas clk driver that's ignoring
clks that are assigned to remote processors in DeviceTree. That's a
new feature that they're using to avoid marking clks as
CLK_IGNORE_UNUSED based on the configuration of the system.
Core:
- Increase dev_id len for clkdev lookups
- Add a devm_clk_bulk_get_all_enable() API to get and enable all clks
for a device
- Add a devm variant of clk_rate_exclusive_get()
New Drivers:
- Display, TCSR, GPU, and Camera clock controllers for Qualcomm's X1
Elite SoC
- Google GS101 PERIC0 and PERIC1 clock controllers
- Exynos850 PDMA clocks
- Exynos850 CPU cluster 0 and 1 (CMU_CPUCLK0/CMU_CPUCLK1) clock
controllers
Removed Drivers:
- Remove the unused Qualcomm sc7180 modem clk driver
Updates:
- Fix some static checker errors in the Hisilicon clk driver
- Polarfire MSSPLL hardware has 4 output clocks (the driver supported
previously only one output); each of these 4 outputs feed dividers
and the output of each divider feed individual hardware blocks
(e.g. CAN, Crypto, eMMC); individual hardware block drivers need to
control their clocks thus clock driver support was added for all
MSSPLL output clocks
- Typo fixes in the Qualcomm IPQ5018 GCC driver
- Add "qdss_at" clk on Qualcomm IPQ6018, needed for WiFi
- Properly terminate frequency tables in different Qualcomm clk
drivers
- Add MDSS, crypto, and SDCC resets on Qualcomm MSM8953
- Add missing UFS CLKREF clks on Qualcomm SC8180X
- Avoid significant delays during boot by adding a softdep on rpmhpd
to Qualcomm SDM845 gcc driver
- Add QUPv3 RCGS w/ DFS and video resets to Qualcomm SM8150 GCC
driver
- Fix the custom GPU GX "do-nothing" method in the Qualcomm GDSC
driver
- Add an external regulator to GX GDSC on Qualcomm SC8280XP GPU clk
driver
- Switch display, GPU, video, and camera Qualcomm clk drivers to
module_platform_driver()
- Set a longer delay for Venus resets on many Qualcomm SoCs
- Correct the GDSC wait times in the Qualcomm SDM845 display clk
driver
- Fix clock listing Oops on Amlogic axg
- New pll-rate for Rockchip rk3568
- i2s rate improvements for Rockchip rk3399
- Rockchip rk3588 syscon clock fixes and removal of overall
clock-number from the rk3588 binding header
- A prerequisite for later improvements to the Rockchip rk3588 linked
clocks
- Minor clean-ups and error handling improvements in both
composite-8m and SCU i.MX clock drivers
- Fix for SAI_MCLK_SEL definition for i.MX8MP
- Register the Samsung CMU MISC clock controller earlier, so the
Multi Core Timer clocksource can use it on Google GS101
- Propagate Exynos850 SPI IPCLK rate change to parents, so the SPI
will get proper clock rates
- Refactor the generic Samsung CPU clock controllers code, preparing
it for supporting Exynos850 CPU clocks
- Fix some clk kerneldoc warnings
- Add Ethernet, SDHI, DMA, and HyperFLASH/QSPI (RPC-IF) clocks on
Renesas R-Car V4M
- Ignore all clocks which are assigned to a non-Linux system in the
Renesas clk driver
- Add watchdog clock on Renesas RZ/G3S
- Add camera (CRU) clock and reset on Renesas RZ/G2UL
- Add support for the Renesas R-Car V4M (R8A779H0) SoC
- Convert some clk bindings to YAML so they can be validated"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (150 commits)
clk: zynq: Prevent null pointer dereference caused by kmalloc failure
clk: fractional-divider: Use bit operations consistently
clk: fractional-divider: Move mask calculations out of lock
clk: Fix clk_core_get NULL dereference
clk: starfive: jh7110-vout: Convert to platform remove callback returning void
clk: starfive: jh7110-isp: Convert to platform remove callback returning void
clk: imx: imx8-acm: Convert to platform remove callback returning void
clk: qcom: gcc-ipq5018: fix register offset for GCC_UBI0_AXI_ARES reset
clk: qcom: gcc-ipq5018: fix 'halt_reg' offset of 'gcc_pcie1_pipe_clk'
clk: qcom: gcc-ipq5018: fix 'enable_reg' offset of 'gcc_gmac0_sys_clk'
clk: qcom: camcc-x1e80100: Fix missing DT_IFACE enum in x1e80100 camcc
clk: qcom: mmcc-msm8974: fix terminating of frequency table arrays
clk: qcom: mmcc-apq8084: fix terminating of frequency table arrays
clk: qcom: camcc-sc8280xp: fix terminating of frequency table arrays
clk: qcom: gcc-ipq9574: fix terminating of frequency table arrays
clk: qcom: gcc-ipq8074: fix terminating of frequency table arrays
clk: qcom: gcc-ipq6018: fix terminating of frequency table arrays
clk: qcom: gcc-ipq5018: fix terminating of frequency table arrays
clk: mediatek: clk-mt8173-apmixedsys: Use common error handling code in clk_mt8173_apmixed_probe()
clk: Add a devm variant of clk_rate_exclusive_get()
...
|
|
CYW43439 is a Wi-Fi + Bluetooth combo device from Infineon. The
WiFi part is capable of 802.11 b/g/n. This chip is present e.g.
on muRata 1YN module. Extend the binding with its DT compatible.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240309031355.269835-1-marex@denx.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The fourth "new features" pull request for v6.9 with changes both in
stack and in drivers. The theme in this pull request is to fix sparse
warnings but we still have some left in wireless subsystem. Otherwise
quite normal.
Major changes:
rtw89
* NL80211_EXT_FEATURE_SCAN_RANDOM_SN support
* NL80211_EXT_FEATURE_SET_SCAN_DWELL support
rtw88
* support for more rtw8811cu and rtw8821cu devices
mt76
* mt76x2u: add Netgear WNDA3100v3 USB
* mt7915: newer ADIE version support
* mt7925: radio temperature sensor support
* mt7996: remove GCMP IGTK offload
* tag 'wireless-next-2024-03-08' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (125 commits)
wifi: rtw89: wow: move release offload packet earlier for WoWLAN mode
wifi: rtw89: wow: set security engine options for 802.11ax chips only
wifi: rtw89: update suspend/resume for different generation
wifi: rtw89: wow: update config mac function with different generation
wifi: rtw89: update DMA function with different generation
wifi: rtw89: wow: update WoWLAN status register for different generation
wifi: rtw89: wow: update WoWLAN reason register for different chips
wifi: brcm80211: handle pmk_op allocation failure
wifi: rtw89: coex: Add coexistence policy to decrease WiFi packet CRC-ERR
wifi: rtw89: coex: When Bluetooth not available don't set power/gain
wifi: rtw89: coex: add return value to ensure H2C command is success or not
wifi: rtw89: coex: Reorder H2C command index to align with firmware
wifi: rtw89: coex: add BTC ctrl_info version 7 and related logic
wifi: rtw89: coex: add init_info H2C command format version 7
wifi: rtw89: 8922a: add coexistence helpers of SW grant
wifi: rtw89: mac: add coexistence helpers {cfg/get}_plt
wifi: cw1200: restore endian swapping
wifi: wlcore: sdio: Rate limit wl12xx_sdio_raw_{read,write}() failures warns
wifi: rtlwifi: Remove rtl_intf_ops.read_efuse_byte
wifi: rtw88: 8821c: Fix false alarm count
...
====================
Link: https://lore.kernel.org/r/20240308100429.B8EA2C433F1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drop reference to the 25MHz clock as it has nothing to do with connecting
the PHY and the MAC.
Add info about the reference clock direction between the PHY and the MAC
as it depends on the selected rmii mode.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20240305141309.127669-1-jeremie.dautheribes@bootlin.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
net/core/page_pool_user.c
0b11b1c5c320 ("netdev: let netlink core handle -EMSGSIZE errors")
429679dcf7d9 ("page_pool: fix netlink dump stop/resume")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Document support for the Renesas Ethernet AVB (EtherAVB-IF) block in the
Renesas R-Car V4M (R8A779H0) SoC.
Signed-off-by: Thanh Quan <thanh.quan.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/0212b57ba1005bb9b5a922f8f25cc67a7bc15f30.1709631152.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.9
Only some minor cleanup in ath11k and ath12k. Adding Jeff as the
maintainer for ath10k, ath11k and ath12k DT bindings.
|
|
The servers for the @codeaurora domain are long retired and any messages
sent there will bounce. Update the maintainer addresses for this
binding to match the entries in .mailmap so that anyone looking in the
file for a contact will see a correct address.
Signed-off-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240223162027.4016065-1-quic_jhugo@quicinc.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add support for ASP 2.2.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ASP 2.2 Ethernet controller uses a brcm unimac.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal delay properties are not mandatory and should have a
documented default value. The device only supports either no delay or a
fixed delay and the device reset default is no delay, document the
default as no delay.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dtschema defines label as string, so $ref in other bindings is
redundant.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek switches can use a reset controller instead of reset-gpios.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: devicetree@vger.kernel.org
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'reset-gpios' should not be mandatory. although they might be
required for some devices if the switch reset was left asserted by a
previous driver, such as the bootloader.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Cc: devicetree@vger.kernel.org
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add documentation for sam9x7 ethernet interface.
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20240223172228.671553-1-varshini.rajendran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add property ti,rmii-mode to support selecting the RMII operation mode
between:
- master mode (PHY operates from a 25MHz clock reference)
- slave mode (PHY operates from a 50MHz clock reference)
If not set, the operation mode is configured by hardware straps.
Signed-off-by: Jérémie Dautheribes <jeremie.dautheribes@bootlin.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Jeff Johnson as a maintainer of the qcom,ath1*k.yaml files.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240217-ath1xk-maintainer-v1-1-9f7ff5fb6bf4@quicinc.com
|
|
MT7981 (Filogic 820) is a low cost version of MT7986 (Filogic 830) with
a similar wireless controller that also supports four interrupts.
Cc: Peter Chiu <chui-hao.chiu@mediatek.com>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
|
The mt7986 can support four interrupts to distribute the interrupts
to different CPUs.
Signed-off-by: Peter Chiu <chui-hao.chiu@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|