| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
For Gen1 isoc-in endpoint on controller before about SSUSB IPM v1.6.0, it
still send out unexpected ACK after receiving a short packet in burst
transfer, this will cause an exception on connected device, specially for
a 4k camera.
Add a quirk property "rx-fifo-depth" to work around this hardware issue,
prefer to use 3k bytes;
The side-effect is that it may cause performance drop about 10%, including
bulk transfer.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20240104061640.7335-1-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SDM660 was abusingly referencing one of the internal bus clocks, that
were recently dropped from Linux (because the original implementation
did not make much sense), circumventing the interconnect framework.
Drop it.
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230721-topic-rpm_clk_cleanup-v3-1-a66e698932e3@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The high speed related interrupts present on QC targets are as follows:
1. dp/dm irq's
These IRQ's directly reflect changes on the DP/DM pads of the SoC. These
are used as wakeup interrupts only on SoCs with non-QUSB2 targets with
exception of SDM670/SDM845/SM6350.
2. qusb2_phy irq
SoCs with QUSB2 PHY do not have separate DP/DM IRQs and expose only a
single IRQ whose behavior can be modified by the QUSB2PHY_INTR_CTRL
register. The required DPSE/DMSE configuration is done in
QUSB2PHY_INTR_CTRL register of phy address space.
3. hs_phy_irq
This is completely different from the above two and is present on all
targets with exception of a few IPQ ones. The interrupt is not enabled by
default and its functionality is mutually exclusive of qusb2_phy on QUSB
targets and DP/DM on femto phy targets.
The DTs of several QUSB2 PHY based SoCs incorrectly define "hs_phy_irq"
when they should have been "qusb2_phy_irq". On Femto phy targets, the
"hs_phy_irq" mentioned is either the actual "hs_phy_irq" or "pwr_event",
neither of which would never be triggered directly are non-functional
currently. The implementation tries to clean up this issue by addressing
the discrepencies involved and fixing the hs_phy_irq's in respective DT's.
Classify SoC's into four groups based on whether qusb2_phy interrupt
or {dp/dm}_hs_phy_irq is used for wakeup in high speed and whether the
SoCs have hs_phy_irq present in them or not. The ss_phy_irq is optional
interrupt because there are mutliple SoC's which either support only High
Speed or there are multiple controllers within same Soc and the secondary
controller is High Speed only capable.
This breaks ABI on targets running older kernels, but since the interrupt
definitions are given wrong on many targets and to establish proper rules
for usage of DWC3 interrupts on Qualcomm platforms, DT binding update is
necessary. The bindings put pwr_event as the first interrupt and ss_phy as
the last. Since all SoCs have the pwr_event (HS) interrupt, but not all
controllers have the SS PHY interrupt, this would prevent, to some extent,
expressing that the SS PHY is optional by keeping it last in the binding
schema and making sure that minItems = maxItems - 1.
No new targets have been added to schema. Only the existing ones have been
re-ordered.
Signed-off-by: Krishna Kurapati <quic_kriskura@quicinc.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231227091951.685-2-quic_kriskura@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 662a60102c12 ("usb: typec: Separate USB Power Delivery from USB
Type-C") allows userspace to configure the PD of a port by selecting
different set of predefined PD capabilities. Define the PD capability
sets in DT for better configurability in device modules.
Define an optional child node "capabilities" to contain multiple USB
Power Delivery capabilities.
Define child nodes with pattern (e.g. caps-0, caps-1) under
"capabilities". Each node contains PDO data of a selectable Power
Delivery capability.
Also define common properties for source-pdos, sink-pdos, and
op-sink-microwatt that can be referenced.
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20231205030114.1349089-2-kyletso@google.com
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231216104630.2720818-2-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add description of the USB-C Accessory Modes supported on the particular
USB-C connector. This is required for devices like Qualcomm SM8150-HDK,
which have no other way to express accessory modes supported by the
hardware platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231215173005.313422-2-dmitry.baryshkov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add X1E80100 to the DT schema.
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231214-x1e80100-usb-v1-1-c22be5c0109e@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Document the Qualcomm WCD9390/WCD9395 USB SubSystem Altmode/Analog Audio Switch
which is a separate USB SubSystem for Altmode/Analog Audio Switch accessible
over an I2C interface.
Since Audio Headphone and Microphone data path between the Codec and the USB-C Mux
subsystems are external to the IC, it requires a second port to handle USB-C altmode
& orientation switching for Audio Accessory Mode to the Codec SubSystem.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231212-topic-sm8650-upstream-wcd939x-usbss-v2-1-38961fea5867@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add description of the USB-C AltModes supported on the particular USB-C
connector. This is required for devices like Qualcomm Robotics RB5,
which have no other way to express alternative modes supported by the
hardware platform.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20231204020303.2287338-2-dmitry.baryshkov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the misspelled "Controller" and "Type-C" words.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231207172912.2658226-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 'peer-hub' is a valid property for the hub.
Document it to fix the following dt-schema warning:
imx8mp-debix-som-a-bmb-08.dtb: hub@1: 'peer-hub' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/usb/genesys,gl850g.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231207124217.2530457-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the USB fixes in here as well to build off of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
- A pair of fixes to the new module load-time relocation code
- A fix for hwprobe overflowing on rv32
- A fix for to correctly decode C.SWSP and C.SDSP, which manifests in
misaligned access handling
- A fix for a boot-time shadow call stack initialization ordering issue
- A fix for Andes' errata probing, which was calling
riscv_noncoherent_supported() too late in the boot process and
triggering an oops
* tag 'riscv-for-linus-6.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: errata: andes: Probe for IOCP only once in boot stage
riscv: Fix SMP when shadow call stacks are enabled
dt-bindings: perf: riscv,pmu: drop unneeded quotes
riscv: fix misaligned access handling of C.SWSP and C.SDSP
RISC-V: hwprobe: Always use u64 for extension bits
Support rv32 ULEB128 test
riscv: Correct type casting in module loading
riscv: Safely remove entries from relocation list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the changes are devicetree fixes for NXP, Mediatek, Rockchips
Arm machines as well as Microchip RISC-V, and most of these address
build-time warnings for spec violations and other minor issues. One of
the Mediatek warnings was enabled by default and prevented a clean
build.
The ones that address serious runtime issues are all on the i.MX
platform:
- a boot time panic on imx8qm
- USB hanging under load on imx8
- regressions on the imx93 ethernet phy
Code fixes include a minor error handling for the i.MX PMU driver, and
a number of firmware driver fixes:
- OP-TEE fix for supplicant based device enumeration, and a new sysfs
attribute to needed to fix a race against userspace
- Arm SCMI fix for possible truncation/overflow in the frequency
computations
- Multiple FF-A fixes for the newly added notification support"
* tag 'soc-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (55 commits)
MAINTAINERS: change the S32G2 maintainer's email address.
arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588
ARM: dts: imx28-xea: Pass the 'model' property
ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
MAINTAINERS: reinstate freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8-apalis: set wifi regulator to always-on
ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
arm64: dts: imx8ulp: update gpio node name to align with register address
arm64: dts: imx93: update gpio node name to align with register address
arm64: dts: imx93: correct mediamix power
arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup
arm64: dts: freescale: imx8-ss-dma: Fix #pwm-cells
arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells
dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles
ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
arm64: dts: rockchip: Fix PCI node addresses on rk3399-gru
arm64: dts: rockchip: drop interrupt-names property from rk3588s dfi
firmware: arm_scmi: Fix possible frequency truncation when using level indexing mode
firmware: arm_scmi: Fix frequency truncation by promoting multiplier type
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Devicetree fixes for the 6.7-cycle.
All over the place this time. From adapting the size of the vdec nodes
on rk3328 and rk3399, fixing some wrong pinctrl settings on rk3128 and
the Turing RK1 board, emmc-settings fixes on rk3588 and interrupt-name
mishaps, down to some dt-cleanups.
Also this adds the missing rockchip,rk3588-pmugrf compatible to the soc
grf binding, that I somehow messed up during the pull requests for the
-rc1 . At least with it included the dt-checker is happier.
* tag 'v6.7-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Fix eMMC Data Strobe PD on rk3588
arm64: dts: rockchip: Fix PCI node addresses on rk3399-gru
arm64: dts: rockchip: drop interrupt-names property from rk3588s dfi
arm64: dts: rockchip: Fix Turing RK1 interrupt pinctrls
ARM: dts: rockchip: Fix sdmmc_pwren's pinmux setting for RK3128
arm64: dts: rockchip: minor whitespace cleanup around '='
ARM: dts: rockchip: minor whitespace cleanup around '='
dt-bindings: soc: rockchip: grf: add rockchip,rk3588-pmugrf
arm64: dts: rockchip: fix rk356x pcie msg interrupt name
arm64: dts: rockchip: Expand reg size of vdec node for RK3399
arm64: dts: rockchip: Expand reg size of vdec node for RK3328
Link: https://lore.kernel.org/r/2709704.mvXUDI8C0e@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix dt-extract-compatibles for builds with in tree build directory
- Drop Xinlei Lee <xinlei.lee@mediatek.com> bouncing email
- Fix the of_reconfig_get_state_change() return value documentation
- Add missing #power-domain-cells property to QCom MPM
- Fix warnings in i.MX LCDIF and adi,adv7533
* tag 'devicetree-fixes-for-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: adi,adv75xx: Document #sound-dai-cells
dt-bindings: lcdif: Properly describe the i.MX23 interrupts
dt-bindings: interrupt-controller: Allow #power-domain-cells
of: dynamic: Fix of_reconfig_get_state_change() return value documentation
dt-bindings: display: mediatek: dsi: remove Xinlei's mail
dt: dt-extract-compatibles: Don't follow symlinks when walking tree
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 6.7:
- A MAINTAINERS update to reinstate freescale ARM64 DT directory in i.MX
entry.
- A series from Alexander Stein to fix #pwm-cells for imx8-ss.
- A series from Haibo Chen to fix GPIO node name for i.MX93 and
i.MX8ULP.
- Add parkmode-disable-ss-quirk for DWC3 on i.MX8MP and i.MX8MQ to fix
an issue that the controller may hang when processing transactions
under heavy USB traffic from multiple endpoints.
- Fix mediamix block power on/off for i.MX93 by correcting the power
domain clock to be 'nic_media'.
- A couple of Ethernet PHY clock regression fixes for imx6ul-pico and
imx6q-skov board.
- Fix edma3 power domain for i.MX8QM to fix a panic during startup
process.
* tag 'imx-fixes-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx28-xea: Pass the 'model' property
ARM: dts: imx7: Declare timers compatible with fsl,imx6dl-gpt
MAINTAINERS: reinstate freescale ARM64 DT directory in i.MX entry
arm64: dts: imx8-apalis: set wifi regulator to always-on
ARM: imx: Check return value of devm_kasprintf in imx_mmdc_perf_init
arm64: dts: imx8ulp: update gpio node name to align with register address
arm64: dts: imx93: update gpio node name to align with register address
arm64: dts: imx93: correct mediamix power
arm64: dts: imx8qm: Add imx8qm's own pm to avoid panic during startup
arm64: dts: freescale: imx8-ss-dma: Fix #pwm-cells
arm64: dts: freescale: imx8-ss-lsio: Fix #pwm-cells
dt-bindings: pwm: imx-pwm: Unify #pwm-cells for all compatibles
ARM: dts: imx6ul-pico: Describe the Ethernet PHY clock
arm64: dts: imx8mp: imx8mq: Add parkmode-disable-ss-quirk on DWC3
ARM: dts: imx6q: skov: fix ethernet clock regression
arm64: dt: imx93: tqma9352-mba93xxla: Fix LPUART2 pad config
Link: https://lore.kernel.org/r/20231207005202.GF270430@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
When using audio from ADV7533 or ADV7535 and describing the audio
card via simple-audio-card, the '#sound-dai-cells' needs to be passed.
Document the '#sound-dai-cells' property to fix the following
dt-schema warning:
imx8mn-beacon-kit.dtb: hdmi@3d: '#sound-dai-cells' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20231206093643.2198562-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
i.MX23 has two LCDIF interrupts instead of a single one like other
i.MX devices.
Take this into account for properly describing the i.MX23 LCDIF
interrupts.
This fixes the following dt-schema warning:
imx23-olinuxino.dtb: lcdif@80030000: interrupts: [[46], [45]] is too long
from schema $id: http://devicetree.org/schemas/display/fsl,lcdif.yaml#
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231206112337.2234849-1-festevam@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Drop unneeded quotes over simple string values to fix a soon to be
enabled yamllint warning:
[error] string value is redundantly quoted with any quotes (quoted-strings)
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231122224414.2809184-1-robh@kernel.org
Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com>
|
|
MPM provides a single genpd. Allow #power-domain-cells = <0>.
Fixes: 54fc9851c0e0 ("dt-bindings: interrupt-controller: Add Qualcomm MPM support")
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231129-topic-mpmbindingspd-v2-1-acbe909ceee1@linaro.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The xHCI IP on the BCM2711 SoC is compatible to "brcm,xhci-brcm-v2",
but also requires a power domain. So introduce a new compatible
and the specific constraints. Since the key allOf can only occur
once, merge the reference below.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231205200531.8232-2-wahrenst@gmx.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use #pwm-cells for all i.MX variants. Only fsl,imx1-pwm does not support
inverted PWM output. Keep it the same for consistency.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The TPS6598x device family provides a high-level reset pin. It can be
either grounded or used to reinitialize all device settings.
Document the reset GPIO as an optional property and add it to the
existing example.
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230912-topic-tps6598x_reset-v3-2-0c2873070a77@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix a really interesting potential core bug in the list iterator
requireing the use of READ_ONCE() discovered when testing kernel
compiles with clang.
- Check devm_kcalloc() return value and an array bounds in the STM32
driver.
- Fix an exotic string truncation issue in the s32cc driver, found by
the kernel test robot (impressive!)
- Fix an undocumented struct member in the cy8c95x0 driver.
- Fix a symbol overlap with MIPS in the Lochnagar driver, MIPS defines
a global symbol "RST" which is a bit too generic and collide with
stuff. OK this one should be renamed too, we will fix that as well.
- Fix erroneous branch taking in the Realtek driver.
- Fix the mail address in MAINTAINERS for the s32g2 driver.
* tag 'pinctrl-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
dt-bindings: pinctrl: s32g2: change a maintainer email address
pinctrl: realtek: Fix logical error when finding descriptor
pinctrl: lochnagar: Don't build on MIPS
pinctrl: avoid reload of p state in list iteration
pinctrl: cy8c95x0: Fix doc warning
pinctrl: s32cc: Avoid possible string truncation
pinctrl: stm32: fix array read out of bound
pinctrl: stm32: Add check for devm_kcalloc
|
|
Xinlei Lee's mail is bouncing:
<xinlei.lee@mediatek.com>: host mailgw02.mediatek.com[216.200.240.185] said:
550 Relaying mail to xinlei.lee@mediatek.com is not allowed (in reply to
RCPT TO command)
Remove it.
Signed-off-by: Michael Walle <mwalle@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231123134927.2034024-1-mwalle@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.7-rc3
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (329 commits)
USB: serial: option: add Luat Air72*U series products
USB: serial: option: add Fibocom L7xx modules
USB: serial: option: fix FM101R-GL defines
USB: serial: option: don't claim interface 4 for ZTE MF290
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
...
|
|
I am leaving SUSE so the current email address <clin@suse.com> will be
disabled soon. <chester62515@gmail.com> will be my new address for handling
emails, patches and pull requests from upstream and communities.
Cc: Chester Lin <chester62515@gmail.com>
Cc: NXP S32 Linux Team <s32@nxp.com>
Cc: Ghennadi Procopciuc <Ghennadi.Procopciuc@oss.nxp.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>
Cc: Conor Dooley <conor+dt@kernel.org>
Signed-off-by: Chester Lin <clin@suse.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20231116001913.16121-1-clin@suse.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Qualcomm SM6125 DWC3 USB controller comes with two interrupts (verified
with downstream/vendor code of Trinket DTSI from Xiaomi Laurel device).
Move the qcom,sm6125-dwc3 to appropriate place in allOf:if:then blocks
constraining interrupts.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Link: https://lore.kernel.org/r/20231111141953.51841-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DP/DM wakeup interrupts are edge triggered and which edge to trigger
on depends on use-case and whether a Low speed or Full/High speed device
is connected.
Fixes: 3828026c9ec8 ("dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB5744 has two power supplies one for 3V3 and one for 1V2. Add the
second supply to the USB5744 DT binding.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20231113145921.30104-2-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Document the SuperSpeed DWC3 USB controller on the SM8650 Platform.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231030-topic-sm8650-upstream-bindings-dwc3-v2-1-60c0824fb835@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USBHS IP block on the RZ/Five SoC is identical to one found on the
RZ/G2UL SoC. "renesas,usbhs-r9a07g043" compatible string will be used on
the RZ/Five SoC so to make this clear and to keep this file consistent,
update the comment to include RZ/Five SoC.
No driver changes are required as generic compatible string
"renesas,rza2-usbhs" will be used as a fallback on RZ/Five SoC.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20231115211407.32067-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The example host controller node has two PHYs and therefore needs two
PHY names.
Fixes: 3aa3c66aedef ("dt-bindings: usb: Bring back phy-names")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231110134802.32060-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven small fixes, six in drivers and one in sd.
The sd fix is so large because it changes a struct pointer to a struct
but otherwise is fairly simple"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: qcom-ufs: dt-bindings: Document the SM8650 UFS Controller
scsi: sd: Fix sshdr use in sd_suspend_common()
scsi: scsi_debug: Delete some bogus error checking
scsi: scsi_debug: Fix some bugs in sdebug_error_write()
scsi: ufs: core: Fix racing issue between ufshcd_mcq_abort() and ISR
scsi: ufs: core: Expand MCQ queue slot to DeviceQueueDepth + 1
scsi: qla2xxx: Fix system crash due to bad pointer access
|
|
Add rockchip,rk3588-pmugrf compatible string.
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Link: https://lore.kernel.org/r/20231018061714.3553817-24-s.hauer@pengutronix.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
When moving the *-internal-delay-ps properties to only apply for RGMII
interface modes there where a typo in the text formatting.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull in queued fixes for 6.7
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a number of input drivers has been converted to use facilities
provided by the device core to instantiate driver-specific attributes
instead of using devm_device_add_group() and similar APIs
- platform input devices have been converted to use remove() callback
returning void
- a fix for use-after-free when tearing down a Synaptics RMI device
- a few flexible arrays in input structures have been annotated with
__counted_by to help hardening efforts
- handling of vddio supply in cyttsp5 driver
- other miscellaneous fixups
* tag 'input-for-v6.7-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: walkera0701 - use module_parport_driver macro to simplify the code
Input: synaptics-rmi4 - fix use after free in rmi_unregister_function()
dt-bindings: input: fsl,scu-key: Document wakeup-source
Input: cyttsp5 - add handling for vddio regulator
dt-bindings: input: cyttsp5: document vddio-supply
Input: tegra-kbc - use device_get_match_data()
Input: Annotate struct ff_device with __counted_by
Input: axp20x-pek - avoid needless newline removal
Input: mt - annotate struct input_mt with __counted_by
Input: leds - annotate struct input_leds with __counted_by
Input: evdev - annotate struct evdev_client with __counted_by
Input: synaptics-rmi4 - replace deprecated strncpy
Input: wm97xx-core - convert to platform remove callback returning void
Input: wm831x-ts - convert to platform remove callback returning void
Input: ti_am335x_tsc - convert to platform remove callback returning void
Input: sun4i-ts - convert to platform remove callback returning void
Input: stmpe-ts - convert to platform remove callback returning void
Input: pcap_ts - convert to platform remove callback returning void
Input: mc13783_ts - convert to platform remove callback returning void
Input: mainstone-wm97xx - convert to platform remove callback returning void
...
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add support for Amlogic C3 and S4 SoCs
- add IT8613 ID
- add MSM8226 and MSM8974 compatibles
- other small fixes and improvements
* tag 'linux-watchdog-6.7-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
dt-bindings: watchdog: Add support for Amlogic C3 and S4 SoCs
watchdog: mlx-wdt: Parameter desctiption warning fix
watchdog: aspeed: Add support for aspeed,reset-mask DT property
dt-bindings: watchdog: aspeed-wdt: Add aspeed,reset-mask property
watchdog: apple: Deactivate on suspend
dt-bindings: watchdog: qcom-wdt: Add MSM8226 and MSM8974 compatibles
dt-bindings: watchdog: fsl-imx7ulp-wdt: Add 'fsl,ext-reset-output'
wdog: imx7ulp: Enable wdog int_en bit for watchdog any reset
drivers: watchdog: marvell_gti: Program the max_hw_heartbeat_ms
drivers: watchdog: marvell_gti: fix zero pretimeout handling
watchdog: marvell_gti: Replace of_platform.h with explicit includes
watchdog: imx_sc_wdt: continue if the wdog already enabled
watchdog: st_lpc: Use device_get_match_data()
watchdog: wdat_wdt: Add timeout value as a param in ping method
watchdog: gpio_wdt: Make use of device properties
sbsa_gwdt: Calculate timeout with 64-bit math
watchdog: ixp4xx: Make sure restart always works
watchdog: it87_wdt: add IT8613 ID
watchdog: marvell_gti_wdt: Fix error code in probe()
Watchdog: marvell_gti_wdt: Remove redundant dev_err_probe() for platform_get_irq()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a few fixes and a bunch of cleanups, a lot of which is
in preparation for Uwe's character device support that may be ready in
time for the next merge window"
* tag 'pwm/for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: samsung: Document new member .channel in struct samsung_pwm_chip
pwm: bcm2835: Add support for suspend/resume
pwm: brcmstb: Checked clk_prepare_enable() return value
pwm: brcmstb: Utilize appropriate clock APIs in suspend/resume
pwm: pxa: Explicitly include correct DT includes
pwm: cros-ec: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: samsung: Consistently use the same name for driver data
pwm: vt8500: Simplify using devm functions
pwm: sprd: Simplify using devm_pwmchip_add() and dev_err_probe()
pwm: sprd: Provide a helper to cast a chip to driver data
pwm: spear: Simplify using devm functions
pwm: mtk-disp: Simplify using devm_pwmchip_add()
pwm: imx-tpm: Simplify using devm functions
pwm: brcmstb: Simplify using devm functions
pwm: bcm2835: Simplify using devm functions
pwm: bcm-iproc: Simplify using devm functions
pwm: Adapt sysfs API documentation to reality
pwm: dwc: add PWM bit unset in get_state call
pwm: dwc: make timer clock configurable
pwm: dwc: split pci out of core driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"Core changes:
- Make default-domains mandatory for all IOMMU drivers
- Remove group refcounting
- Add generic_single_device_group() helper and consolidate drivers
- Cleanup map/unmap ops
- Scaling improvements for the IOVA rcache depot
- Convert dart & iommufd to the new domain_alloc_paging()
ARM-SMMU:
- Device-tree binding update:
- Add qcom,sm7150-smmu-v2 for Adreno on SM7150 SoC
- SMMUv2:
- Support for Qualcomm SDM670 (MDSS) and SM7150 SoCs
- SMMUv3:
- Large refactoring of the context descriptor code to move the CD
table into the master, paving the way for '->set_dev_pasid()'
support on non-SVA domains
- Minor cleanups to the SVA code
Intel VT-d:
- Enable debugfs to dump domain attached to a pasid
- Remove an unnecessary inline function
AMD IOMMU:
- Initial patches for SVA support (not complete yet)
S390 IOMMU:
- DMA-API conversion and optimized IOTLB flushing
And some smaller fixes and improvements"
* tag 'iommu-updates-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (102 commits)
iommu/dart: Remove the force_bypass variable
iommu/dart: Call apple_dart_finalize_domain() as part of alloc_paging()
iommu/dart: Convert to domain_alloc_paging()
iommu/dart: Move the blocked domain support to a global static
iommu/dart: Use static global identity domains
iommufd: Convert to alloc_domain_paging()
iommu/vt-d: Use ops->blocked_domain
iommu/vt-d: Update the definition of the blocking domain
iommu: Move IOMMU_DOMAIN_BLOCKED global statics to ops->blocked_domain
Revert "iommu/vt-d: Remove unused function"
iommu/amd: Remove DMA_FQ type from domain allocation path
iommu: change iommu_map_sgtable to return signed values
iommu/virtio: Add __counted_by for struct viommu_request and use struct_size()
iommu/vt-d: debugfs: Support dumping a specified page table
iommu/vt-d: debugfs: Create/remove debugfs file per {device, pasid}
iommu/vt-d: debugfs: Dump entry pointing to huge page
iommu/vt-d: Remove unused function
iommu/arm-smmu-v3-sva: Remove bond refcount
iommu/arm-smmu-v3-sva: Remove unused iommu_sva handle
iommu/arm-smmu-v3: Rename cdcfg to cd_table
...
|
|
Document the UFS Controller on the SM8650 Platform.
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231030-topic-sm8650-upstream-bindings-ufs-v3-1-a96364463fd5@linaro.org
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull more drm updates from Dave Airlie:
"Geert pointed out I missed the renesas reworks in my main pull, so
this pull contains the renesas next work for atomic conversion and DT
support.
It also contains a bunch of amdgpu and some small ssd13xx fixes.
renesas:
- atomic conversion
- DT support
ssd13xx:
- dt binding fix for ssd132x
- Initialize ssd130x crtc_state to NULL.
amdgpu:
- Fix RAS support check
- RAS fixes
- MES fixes
- SMU13 fixes
- Contiguous memory allocation fix
- BACO fixes
- GPU reset fixes
- Min power limit fixes
- GFX11 fixes
- USB4/TB hotplug fixes
- ARM regression fix
- GFX9.4.3 fixes
- KASAN/KCSAN stack size check fixes
- SR-IOV fixes
- SMU14 fixes
- PSP13 fixes
- Display blend fixes
- Flexible array size fixes
amdkfd:
- GPUVM fix
radeon:
- Flexible array size fixes"
* tag 'drm-next-2023-11-07' of git://anongit.freedesktop.org/drm/drm: (83 commits)
drm/amd/display: Enable fast update on blendTF change
drm/amd/display: Fix blend LUT programming
drm/amd/display: Program plane color setting correctly
drm/amdgpu: Query and report boot status
drm/amdgpu: Add psp v13 function to query boot status
drm/amd/swsmu: remove fw version check in sw_init.
drm/amd/swsmu: update smu v14_0_0 driver if and metrics table
drm/amdgpu: Add C2PMSG_109/126 reg field shift/masks
drm/amdgpu: Optimize the asic type fix code
drm/amdgpu: fix GRBM read timeout when do mes_self_test
drm/amdgpu: check recovery status of xgmi hive in ras_reset_error_count
drm/amd/pm: only check sriov vf flag once when creating hwmon sysfs
drm/amdgpu: Attach eviction fence on alloc
drm/amdkfd: Improve amdgpu_vm_handle_moved
drm/amd/display: Increase frame warning limit with KASAN or KCSAN in dml2
drm/amd/display: Avoid NULL dereference of timing generator
drm/amdkfd: Update cache info for GFX 9.4.3
drm/amdkfd: Populate cache info for GFX 9.4.3
drm/amdgpu: don't put MQDs in VRAM on ARM | ARM64
drm/amdgpu/smu13: drop compute workload workaround
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux
Pull remoteproc updates from Bjorn Andersson:
"Support for controlling the second core in Mediatek's SCP dual-core
setup is introduced.
Support for audio, compute and modem DSPs on Qualcomm SM6375, and the
audio DSP in SC7180 are introduced. The peripheral NoC clock is
dropped from MSM8996 modem DSP, as this is handled through the
interconnect provider.
In the zynqmp driver the setup for TCM memory, and device address
translation thereof, when operating in lockstep mode is corrected.
A few bug fixes and cleanups are introduces across the ST and STM32
remoteproc drivers"
* tag 'rproc-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (28 commits)
remoteproc: st: Fix sometimes uninitialized ret in st_rproc_probe()
remoteproc: st: Use device_get_match_data()
remoteproc: zynqmp: Change tcm address translation method
remoteproc: mediatek: Refactor single core check and fix retrocompatibility
remoteproc: qcom: q6v5-mss: Remove PNoC clock from 8996 MSS
dt-bindings: remoteproc: qcom,msm8996-mss-pil: Remove PNoC clock
dt-bindings: remoteproc: qcom,adsp: Remove AGGRE2 clock
remoteproc: qcom: pas: Add SM6375 MPSS
remoteproc: qcom: pas: Add SM6375 ADSP & CDSP
dt-bindings: remoteproc: qcom,sm6375-pas: Document remoteprocs
dt-bindings: remoteproc: pru: Add Interrupt property
remoteproc: qcom: pas: Add sc7180 adsp
dt-bindings: remoteproc: qcom: sc7180-pas: Add ADSP compatible
arm64: dts: mediatek: Update the node name of SCP rpmsg subnode
remoteproc: zynqmp: fix TCM carveouts in lockstep mode
remoteproc: mediatek: Refine ipi handler error message
remoteproc: mediatek: Report watchdog crash to all cores
remoteproc: mediatek: Handle MT8195 SCP core 1 watchdog timeout
remoteproc: mediatek: Setup MT8195 SCP core 1 SRAM offset
remoteproc: mediatek: Remove dependency of MT8195 SCP L2TCM power control on dual-core SCP
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- the old V4L2 core videobuf kAPI was finally removed. All media
drivers should now be using VB2 kAPI
- new automotive driver: mgb4
- new platform video driver: npcm-video
- new sensor driver: mt9m114
- new TI driver used in conjunction with Cadence CSI2RX IP to bridge
TI-specific parts
- ir-rx51 was removed and the N900 DT binding was moved to the
pwm-ir-tx generic driver
- drop atomisp-specific ov5693, using the upstream driver instead
- the camss driver has gained RDI3 support for VFE 17x
- the atomisp driver now detects ISP2400 or ISP2401 at run time. No
need to set it up at build time anymore
- lots of driver fixes, cleanups and improvements
* tag 'media/v6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
media: nuvoton: VIDEO_NPCM_VCD_ECE should depend on ARCH_NPCM
media: venus: Fix firmware path for resources
media: venus: hfi_cmds: Replace one-element array with flex-array member and use __counted_by
media: venus: hfi_parser: Add check to keep the number of codecs within range
media: venus: hfi: add checks to handle capabilities from firmware
media: venus: hfi: fix the check to handle session buffer requirement
media: venus: hfi: add checks to perform sanity on queue pointers
media: platform: cadence: select MIPI_DPHY dependency
media: MAINTAINERS: Fix path for J721E CSI2RX bindings
media: cec: meson: always include meson sub-directory in Makefile
media: videobuf2: Fix IS_ERR checking in vb2_dc_put_userptr()
media: platform: mtk-mdp3: fix uninitialized variable in mdp_path_config()
media: mediatek: vcodec: using encoder device to alloc/free encoder memory
media: imx-jpeg: notify source chagne event when the first picture parsed
media: cx231xx: Use EP5_BUF_SIZE macro
media: siano: Drop unnecessary error check for debugfs_create_dir/file()
media: mediatek: vcodec: Handle invalid encoder vsi
media: aspeed: Drop unnecessary error check for debugfs_create_file()
Documentation: media: buffer.rst: fix V4L2_BUF_FLAG_PREPARED
Documentation: media: gen-errors.rst: fix confusing ENOTTY description
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"There is a new driver for the RTC of the Mstar SSD202D SoC. The
rtc7301 driver gains support for byte addresses to support the
USRobotics USR8200. Then we have many non user visible changes and
typo fixes.
Summary:
Subsytem:
- convert platform drivers to remove_new
- prevent modpost warnings for unremovable platform drivers
New driver:
- Mstar SSD202D
Drivers:
- brcmstb-waketimer: support level alarm_irq
- ep93xx: add DT support
- rtc7301: support byte-addressed IO"
* tag 'rtc-6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (28 commits)
dt-bindings: rtc: Add Mstar SSD202D RTC
rtc: Add support for the SSD202D RTC
rtc: at91rm9200: annotate at91_rtc_remove with __exit again
dt-bindings: rtc: microcrystal,rv3032: Document wakeup-source property
dt-bindings: rtc: pcf8523: Convert to YAML
dt-bindings: rtc: mcp795: move to trivial-rtc
rtc: ep93xx: add DT support for Cirrus EP93xx
dt-bindings: rtc: Add Cirrus EP93xx
dt-bindings: rtc: pcf2123: convert to YAML
rtc: efi: fixed typo in efi_procfs()
rtc: omap: Use device_get_match_data()
rtc: pcf85363: fix wrong mask/val parameters in regmap_update_bits call
rtc: rtc7301: Support byte-addressed IO
rtc: rtc7301: Rewrite bindings in schema
rtc: sh: Convert to platform remove callback returning void
rtc: pxa: Convert to platform remove callback returning void
rtc: mv: Convert to platform remove callback returning void
rtc: imxdi: Convert to platform remove callback returning void
rtc: at91rm9200: Convert to platform remove callback returning void
rtc: pcap: Drop no-op remove function
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox
Pull mailbox updates from Jassi Brar:
- imx: add support for TX Doorbell v2
- mtk: implement runtime PM
- zynqmp: add destination mailbox compatible
- qcom:
- add another clock provider for IPQ
- add SM8650 compatible
- misc: use preferred device_get_match_data()
* tag 'mailbox-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/jassibrar/mailbox:
dt-bindings: mailbox: qcom-ipcc: document the SM8650 Inter-Processor Communication Controller
mailbox: mtk-cmdq-mailbox: Implement Runtime PM with autosuspend
mailbox: Use device_get_match_data()
dt-bindings: zynqmp: add destination mailbox compatible
dt-bindings: mailbox: qcom: add one more clock provider for IPQ mailbox
mailbox: imx: support channel type tx doorbell v2
dt-bindings: mailbox: fsl,mu: add new tx doorbell channel
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next-fixes for v6.7-rc1:
- dt binding fix for ssd132x
- Initialize ssd130x crtc_state to NULL.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/58f40043-bb8a-4716-bf07-89f6a9f56c4c@linux.intel.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"I2C has largely driver updates for 6.7, i.e. feature additions (like
adding transfers while in atomic mode), using new helpers (like
devm_clk_get_enabled), new IDs, documentation fixes and additions...
you name it.
The core got a memleak fix and better support for nested muxes"
* tag 'i2c-for-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (53 commits)
i2c: s3c2410: make i2c_s3c_irq_nextbyte() void
i2c: qcom-geni: add ACPI device id for sc8180x
Documentation: i2c: add fault code for not supporting 10 bit addresses
i2c: sun6i-p2wi: Prevent potential division by zero
i2c: mux: demux-pinctrl: Convert to use sysfs_emit_at() API
i2c: i801: Use new helper acpi_use_parent_companion
ACPI: Add helper acpi_use_parent_companion
MAINTAINERS: add YAML file for i2c-demux-pinctrl
i2c: core: fix lockdep warning for sparsely nested adapter chain
i2c: axxia: eliminate kernel-doc warnings
dt-bindings: i2c: i2c-demux-pinctrl: Convert to json-schema
i2c: stm32f7: Use devm_clk_get_enabled()
i2c: stm32f4: Use devm_clk_get_enabled()
i2c: stm32f7: add description of atomic in struct stm32f7_i2c_dev
i2c: fix memleak in i2c_new_client_device()
i2c: exynos5: Calculate t_scl_l, t_scl_h according to i2c spec
i2c: i801: Simplify class-based client device instantiation
i2c: exynos5: add support for atomic transfers
i2c: at91-core: Use devm_clk_get_enabled()
eeprom: at24: add ST M24C64-D Additional Write lockable page support
...
|
