summaryrefslogtreecommitdiff
path: root/Documentation/devicetree
AgeCommit message (Collapse)AuthorFilesLines
2019-07-06dt-bindings: net: bluetooth: add clock property to UART-based deviceSean Wang1-0/+4
Some board requires explicitily control external osscilator via GPIO. So, add a clock property for an external oscillator for the device. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06dt-bindings: net: bluetooth: add boot-gpios property to UART-based deviceSean Wang1-0/+13
Not every platform has the pinctrl device integrates the GPIO the function such as MT7621 whose pinctrl and GPIO are separate hardware so adding an additional boot-gpios property for such platform allows them to bring up the device. Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06dt-bindings: net: bluetooth: Add device property firmware-name for QCA6174Rocky Liao1-0/+4
This patch adds an optional device property "firmware-name" to allow the driver to load customized nvm firmware file based on this property. Signed-off-by: Rocky Liao <rjliao@codeaurora.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-06Bluetooth: hci_mrvl: Add serdev supportSascha Hauer1-0/+25
This adds serdev support to the Marvell hci uart driver. Only basic serdev support, none of the fancier features like regulator or enable GPIO support is added for now. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-07-05dt-bindings: i2c: sun6i-p2wi: Fix the binding exampleMaxime Ripard1-1/+1
Even though the binding claims that the frequency can go up to 6MHz, the common i2c binding sets a limit at 3MHz, which then triggers a warning. Since the only SoC that uses that bus uses a frequency of 100kHz, and that this bus hasn't been found in an SoC for something like 5 years, let's just fix the example to have a frequency within the acceptable range for i2c. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-07-05dt-bindings: i2c: mv64xxx: Fix the example compatibleMaxime Ripard1-1/+1
One example has a compatible that isn't a valid combination according to the binding, and now that the examples are validated as well, this generates a warning. Let's fix this. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-07-04Merge branch 'spi-5.3' into spi-nextMark Brown13-297/+637
2019-07-04Merge branch 'regulator-5.3' into regulator-nextMark Brown11-245/+530
2019-07-04Revert "dt-bindings: add binding for USBSS-DRD controller."Greg Kroah-Hartman1-45/+0
This reverts commit e8a8b40cc8922b38f91c6562d525f21f312f235c. It's broken. Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Felipe Balbi <balbi@kernel.org> Cc: Pawel Laszczak <pawell@cadence.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-04dt-bindings: coresight: Change CPU phandle to required propertySai Prakash Ranjan2-5/+7
Do not assume the affinity to CPU0 if cpu phandle is omitted. Update the DT binding rules to reflect the same by changing it to a required property. Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Link: https://lore.kernel.org/r/0f7f4105d5ffea6ca4313271f3b3fee69da2106a.1562229018.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-07-04dt-bindings: i3c: cdns: Use correct cells for I2C deviceQii Wang1-1/+1
I2C device reg should be "reg = <0x52 0x0 0x10>;" Fixes: e29d0d9c90c9 ("dt-bindings: i3c: Document Cadence I3C master bindings") Signed-off-by: Qii Wang <qii.wang@mediatek.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
2019-07-04dt-bindings: pinctrl: qcom: Add SM8150 pinctrl bindingPrasad Sodagudi1-0/+190
Add the binding for the TLMM pinctrl block found in the SM8150 platform. Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by: Isaac J. Manjarres <isaacm@codeaurora.org> [vkoul: add missing nodes of gpio range and reserved rewrote function names and order them] Signed-off-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20190702105045.27646-3-vkoul@kernel.org Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-04dt-bindings: pinctrl: qcom: Document missing gpio nodesVinod Koul1-0/+10
The bindings for msm8998-pinctrl was missing gpio-ranges and gpio-reserved-ranges, so document them as well Signed-off-by: Vinod Koul <vkoul@kernel.org> Link: https://lore.kernel.org/r/20190702105045.27646-2-vkoul@kernel.org Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-03dt-bindings: usb: ehci: Fix example warningsMaxime Ripard1-2/+1
The example of the EHCI binding generates a bunch of warnings now that the examples are validated too. Most notably, phy-names isn't used at all, and the node name should be USB. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03dt-bindings: net: Use phy-mode instead of phy-connection-typeMaxime Ripard3-8/+8
When adding support for the DWMAC (and derivatives) bindings, phy-connection-type was required, even though the previous binding required the equivalent phy-mode. Let's fix this by using phy-mode as we should have. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03dt-bindings: simple-framebuffer: Add requirement for pipelinesMaxime Ripard1-0/+23
Both the allwinner and amlogic compatibles require that either the allwinner,pipeline or the amlogic,pipeline property is set. This was dropped during the conversion since we didn't have conditionals back then, but we can express this properly now. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03dt-bindings: display: Fix simple-framebuffer exampleMaxime Ripard1-1/+1
The simple-framebuffer binding has a compatible that isn't one of the valid options. Since an Allwinner pipeline is being described, let's add the matching compatible. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03dt-bindings: net: mdio: Add child nodesMaxime Ripard1-0/+14
The child nodes of a mdio bus are supposed to be ethernet PHYs, with a reg property. Make sure that's validated as well. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03dt-bindings: net: mdio: Add address and size cellsMaxime Ripard1-0/+6
MDIO controllers should have child nodes with a singe value in their reg properties being the ID of the PHY in the bus. Let's add the proper constraints on #address-cells and #size-cells. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03dt-bindings: net: mdio: Add a nodename patternMaxime Ripard1-0/+3
The node name of an MDIO controller should be MDIO. Let's add a rule for this. Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-07-03ASoC: meson: axg-tdm-formatter: add reset to the bindings documentationJerome Brunet1-1/+5
Add an optional reset property to the tdm formatter bindings. The dedicated reset line is present on some SoC families, such as the g12a. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Link: https://lore.kernel.org/r/20190703120749.32341-2-jbrunet@baylibre.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-03Merge tag 'usb-for-v5.3-part2' of ↵Greg Kroah-Hartman2-1/+47
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: USB: more changes for v5.3 merge window Turns out a few more important changes came about. We have the new Cadence DRD Driver being added here and that's the biggest, most important part. Together with that we have suport for new imx7ulp phy. Support for TigerLake Devices on dwc3. Also a couple important fixes which weren't completed in time for the -rc cycle. Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> * tag 'usb-for-v5.3-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: usb: renesas_usbhs: add a workaround for a race condition of workqueue usb: gadget: udc: renesas_usb3: remove redundant assignment to ret usb: dwc2: use a longer AHB idle timeout in dwc2_core_reset() USB: gadget: function: fix issue Unneeded variable: "value" usb: phy: phy-mxs-usb: add imx7ulp support doc: dt-binding: mxs-usb-phy: add compatible for 7ulp usb:cdns3 Fix for stuck packets in on-chip OUT buffer. usb:cdns3 Add Cadence USB3 DRD Driver usb:gadget Simplify usb_decode_get_set_descriptor function. usb:gadget Patch simplify usb_decode_set_clear_feature function. usb:gadget Separated decoding functions from dwc3 driver. dt-bindings: add binding for USBSS-DRD controller. usb: dwc3: pci: add support for TigerLake Devices
2019-07-03Merge branch 'timers/vdso' into timers/coreThomas Gleixner3-0/+194
so the hyper-v clocksource update can be applied.
2019-07-03dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schemaAndrew Jeffery2-119/+134
Convert ASPEED pinctrl bindings to DT schema format using json-schema. Cc: Johnny Huang <johnny_huang@aspeedtech.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20190628023838.15426-4-andrew@aj.id.au Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-03dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schemaAndrew Jeffery2-80/+81
Convert ASPEED pinctrl bindings to DT schema format using json-schema Cc: Johnny Huang <johnny_huang@aspeedtech.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Link: https://lore.kernel.org/r/20190628023838.15426-3-andrew@aj.id.au Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-03dt-bindings: pinctrl: aspeed: Split bindings document in twoAndrew Jeffery2-58/+85
Have one for each of the AST2400 and AST2500. The only thing that was common was the fact that both support ASPEED BMC SoCs. Cc: Johnny Huang <johnny_huang@aspeedtech.com> Signed-off-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Joel Stanley <joel@jms.id.au> Link: https://lore.kernel.org/r/20190628023838.15426-2-andrew@aj.id.au Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-07-03dt-bindings: interrupt-controller: Add Amazon's Annapurna Labs FICTalel Shenhar1-0/+29
Document Amazon's Annapurna Labs Fabric Interrupt Controller SoC binding. Signed-off-by: Talel Shenhar <talel@amazon.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
2019-07-03doc: dt-binding: mxs-usb-phy: add compatible for 7ulpPeter Chen1-1/+2
Add compatible for 7ulp USB PHY. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-03dt-bindings: add binding for USBSS-DRD controller.Pawel Laszczak1-0/+45
This patch aim at documenting USB related dt-bindings for the Cadence USBSS-DRD controller. Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2019-07-02ASoC: max98357a: avoid speaker pop when playback startupMac Chiang1-0/+4
Loud speaker pop happens during playback even when in slience playback. Specify Max98357a amp delay times to make sure clocks are always earlier than sdmode on. Signed-off-by: Mac Chiang <mac.chiang@intel.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-02dt-bindings: regulator: add support for the stm32-boosterFabrice Gasnier1-0/+18
Document the 3.3V booster regulator embedded in stm32h7 and stm32mp1 devices, that can be used to supply ADC analog input switches. It's controlled by using system configuration registers (SYSCFG). Introduce two compatibles as the booster regulator is controlled by: - a unique register/bit in STM32H7 - a set/clear register pair in STM32MP1 Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Signed-off-by: Mark Brown <broonie@kernel.org>
2019-07-02dt-bindings: mfd: Add link to ROHM BD71847 DatasheetMatti Vaittinen1-0/+2
ROHM BD71847 PMIC datasheet was published. Add datasheet link for BD71847 as well. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2019-07-02dt-bindings: Add binding for cros-ec-rpmsgPi-Hsun Shih1-1/+4
Add a DT binding documentation for ChromeOS EC driver over rpmsg. Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2019-07-02mfd: madera: Update DT bindings to add additional CODECsRichard Fitzgerald1-2/+6
This adds the cs47l15, cs42l92, cs47l92 and cs47l93 to the list of compatible strings and updates some properties that need to note the new CODECs. Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2019-07-02dt-bindings: mfd: Document short/long press duration for BD718X7Leonard Crestez1-0/+8
These values can be overwritten at probe time. Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Acked-By: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2019-07-02Merge branches 'ib-mfd-clk-gpio-power-regulator-rtc-5.3', ↵Lee Jones2-0/+80
'ib-mfd-clk-regulator-rtc-5.3', 'ib-mfd-cros-5.3' and 'ib-mfd-regulator-5.3' into ibs-for-mfd-merged
2019-07-01Merge tag 'phy-for-5.3' of ↵Greg Kroah-Hartman3-0/+89
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next phy: for 5.3 *) Add a new PHY driver for Qualcomm PCIe2 PHY *) Add a new PHY driver for Mixel DPHY present in i.MX8 *) Fix Qualcomm QMP UFS PHY driver from incorrectly reporting that PHY enable failed *) Fix _BUG_ on Amlogic G12A USB3 + PCIE Combo PHY Driver due to calling a sleeping function from invalid context *) Fix WARN_ON dump on rcar-gen3-usb2 PHY driver caused due to imbalance powered flag *) Fix .cocci and sparse warnings Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> * tag 'phy-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: phy: qcom-qmp: Raise qcom_qmp_phy_enable() polling delay phy: meson-g12a-usb3-pcie: disable locking for cr_regmap phy: Add driver for mixel mipi dphy found on NXP's i.MX8 SoCs dt-bindings: phy: Add documentation for mixel dphy dt-bindings: phy-pxa-usb: add bindings phy: renesas: rcar-gen3-usb2: fix imbalance powered flag phy: qcom-qmp: Drop useless msm8998_pciephy_cfg setting phy: qcom-qmp: Correct READY_STATUS poll break condition phy: ti: am654-serdes: Make serdes_am654_xlate() static phy: usb: phy-brcm-usb: Fix platform_no_drv_owner.cocci warnings phy: samsung: Use struct_size() in devm_kzalloc() phy: qcom: Add Qualcomm PCIe2 PHY driver dt-bindings: phy: Add binding for Qualcomm PCIe2 PHY
2019-07-01Merge tag 'phy-for-5.2-rc_v2' of ↵Greg Kroah-Hartman1-0/+12
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next Kishon writes: phy: for 5.2-rc *) Move Tegra124 PLL power supplies to be enabled by xusb-tegra124 *) Move Tegra210 PLL power supplies to be enabled by xusb-tegra210 *) Minor fixes: fix memory leaks at error path and addresses coverity. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> * tag 'phy-for-5.2-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: phy: tegra: xusb: Add Tegra210 PLL power supplies phy: tegra: xusb: Add Tegra124 PLL power supplies dt-bindings: phy: tegra-xusb: List PLL power supplies phy: usb: phy-brcm-usb: Remove sysfs attributes upon driver removal phy: renesas: rcar-gen2: Fix memory leak at error paths phy: qcom-qusb2: fix missing assignment of ret when calling clk_prepare_enable
2019-07-01Merge tag 'usb-for-v5.3' of ↵Greg Kroah-Hartman4-0/+5
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next Felipe writes: usb: changes for v5.3 merge window The biggest part here is a set of patches removing unnecesary variables from several drivers. Meson-g12a's dwc3 glue implemented IRQ-based OTG/DRD role swap. Qcom's dwc3 glue added support for ACPI, mainly for the AArch64-based SoCs. DWC3 also got support for Intel Elkhart Lake platforms. * tag 'usb-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (30 commits) usb: dwc3: remove unused @lock member of dwc3_ep struct usb: dwc3: pci: Add Support for Intel Elkhart Lake Devices usb: Replace snprintf with scnprintf in gether_get_ifname usb: gadget: ether: Fix race between gether_disconnect and rx_submit usb: gadget: storage: Remove warning message usb: dwc3: gadget: Add support for disabling U1 and U2 entries usb: gadget: send usb_gadget as an argument in get_config_params doc: dt: bindings: usb: dwc3: Update entries for disabling U1 and U2 usb: dwc3: qcom: Use of_clk_get_parent_count() usb: dwc3: Fix core validation in probe, move after clocks are enabled usb: dwc3: qcom: Improve error handling usb: dwc3: qcom: Start USB in 'host mode' on the SDM845 usb: dwc3: qcom: Add support for booting with ACPI soc: qcom: geni: Add support for ACPI Revert "usb: dwc2: host: Setting qtd to NULL after freeing it" usb: gadget: net2272: remove redundant assignments to pointer 's' usb: gadget: Zero ffs_io_data USB: omap_udc: Remove unneeded variable fotg210-udc: Remove unneeded variable usb: gadget: at91_udc: Remove unneeded variable ...
2019-07-01Merge tag 'extcon-next-for-5.3' of ↵Greg Kroah-Hartman1-0/+19
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next Chanwoo writes: Update extcon for 5.3 Detailed description for this pull request: 1. Add new extcon-fsa9480 extcon provider driver - It is extcon provide driver for Fairchild Semiconductor FSA9480 microUSB switch and accessory detector chip which detects the kind of external connector like usb, charger, audio, video and so on. 2. - Add the exception handling code for extcon-arizona.c when using the regmap interface. * tag 'extcon-next-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon: extcon: fsa9480: Fix Kconfig warning and build errors extcon: Add fsa9480 extcon driver dt-bindings: extcon: Add support for fsa9480 switch extcon: arizona: Correct error handling on regmap_update_bits_check
2019-07-01Merge tag 'iio-for-5.3b' of ↵Greg Kroah-Hartman10-168/+408
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next Jonathan writes: Second set of IIO device support, features, cleanups and minor fixes for 5.3. A few bits for the counters subsystem mixed in here as well. There are some late breaking fixes as well, which aren't so urgent they can't wait for the merge window. New Device Support * adf4371 - New driver + bindings. - Support the adf4372 PLL. Mostly ID and bindings. * ad8366 (note includes rework of driver needed to allow support for these). - Support the ADL5240 variable gain amplifier (VGA). - Support the ADA4961 digital gain amplifier (DGA). * dps310 - New driver, in several parts from different authors for this temp and pressure sensor. - Includes errata workaround for a temperature reading issue. * stk3310 - Support the stk3335, mostly ID. Features and cleanups * core - drop error handling on debugfs registration. - harden by making sure we don't overrun iio_chan_info_postfix. * docs - convert remaining docs to rst. At somepoint we'll fit these few into the main IIO docs. - improve sampling_frequency_available docs but explaining the range form. * ad_sigma_delta - Drop a pointless goto. * ad2s1210 - Drop pointless platform data null check seeing as we don't actually use platform data anymore. * ad7124 - Relax limitation on channel numbers to allow pseudo different channels. - Support control of whether the input is buffered via DT. - Use dynamic allocation for channel configuration to make it easier to support new devices. - YAML binding conversion. * ad7150 - Comment tidy up. - Consistent and simple if (ret) handling of i2c errors. - FIELD_GET and GENMASK. - Ternary rather than !!(condition) for readability. - Use macros to avoid repetition of channel definitions. * ad7606 - Add software channel config (rather that pin controlled) - Refactor to simplify addition of new part in future. * ad7746 - of_deivce_id table. * ad7780 - MAINTAINERS entry - YAML DT bindings. * ad8366 - Stop using core mlock in favour of well scoped local lock. - SPDX + copyright date update. * ad9834 - of_device_id table * adf4371 - Add support for output stage muting before lock on has occured. * adis library - MAINTAINERS entry to reflect that this now Alexandru's problem ;) * adis162xx: - Fix a slightly incorrect set of comments and print statements on minimum supported voltage. * adis16203 - of_device_id table. * adis16240 - Add of_device_id table (in two parts as first patch only used it for MODULE_DEVICE_TABLE.) * adt7316-spi - of_device_id table * adxl372 - YAML DT binding conversion. - Cleanup use of buffer callback functions (precursor to core rework). * bh1710 - Simplify getting the i2c adapter from the client. * dht11 - Mote to newer GPIO consumer interface. * kxcjk-1013.c - Add binding for sensor in display of some ultrabooks after userspace tools updated for it not be a problem to report two similar sensors. * imx7d - drop unused variables. - white space - define instead of variable for clock frequency that is fixed. - drop pointless error message. * messon_saradc - SPDX * sps30 - MAINTAINERS entry - YAML binding conversion. * st_accel - Tidy up ordering in various buffer related callbacks. This is part of a long running effort to simplify the core code. * stm32-dfsdm: - Manage the resolution cleanly in triggerd modes. - Add fast mode support which allows more flexible filter choices. - Add a comment on the reason for a 16 bit record when technically not 'required'. * st_lsm6dsx - Embed device name in the sensor_settings struct as i3c doesn't have a convenient name field to use for this. * xilinx-adc - Relax constraints on supported platforms to reflect that this can used with FPGAs on PCIe cards and hence many architectures. * counters/ftm-quaddec - Fix some formatting io MODULE_AUTHOR - MAINTAINERS entry Fixes * tools - fix incorrect handling of 32 bit channels. * sca3000 - Potential endian bug that is unlikely to bite anyone (be64 host seems unlikely for this old part). * stm32-adc - Add vdda-supply. On some boards it needs to be turned on to supply the ADC. DT bindings included. * stm32-dfsdm - Fix output resolution to work with filter orders other than 3. - Fix output datatype as it's signed and previously claimed not to be. * tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits) iio: iio-utils: Fix possible incorrect mask calculation iio: frequency: adf4371: Add support for output stage mute dt-bindings: iio: frequency: Add ADF4372 PLL documentation iio: frequency: adf4371: Add support for ADF4372 PLL dt-bindings: iio: adc: Add buffered input property Convert AD7124 bindings documentation to YAML format. iio: adc: ad7124: Shift to dynamic allocation for channel configuration iio: adc: ad7124: Add buffered input support iio: adc: ad7124: Remove input number limitation MAINTAINERS: add ADIS IMU driver library entry iio: adis162xx: fix low-power docs & reports counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR iio: core: no need to check return value of debugfs_create functions docs: iio: convert to ReST iio: adc: stm32-adc: add missing vdda-supply dt-bindings: iio: adc: stm32: add missing vdda supply iio: adc: stm32-dfsdm: add comment for 16 bits record iio: adc: stm32-dfsdm: add fast mode support iio: adc: stm32-dfsdm: manage data resolution in trigger mode iio: adc: stm32-dfsdm: fix data type ...
2019-06-29dt-bindings: i2c-stm32: document optional dmasFabrice Gasnier1-0/+2
Add missing documentation for "dmas" and "dma-names" properties that can be used on i2c-stm32. Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com> Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com> Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2019-06-28dt-bindings: mtd: sunxi-nand: Drop 'maxItems' from child 'reg' propertyRob Herring1-1/+0
Mixing 'maxItems' and scalar properties doesn't make much sense, so drop 'maxItems' as a single item is implied. Cc: David Woodhouse <dwmw2@infradead.org> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Miquel Raynal <miquel.raynal@bootlin.com> Cc: Richard Weinberger <richard@nod.at> Cc: Vignesh Raghavendra <vigneshr@ti.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Chen-Yu Tsai <wens@csie.org> Cc: linux-mtd@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: arm: Limit cpus schema to only check Arm 'cpu' nodesRob Herring1-263/+224
Matching on the 'cpus' node was a bad choice because the schema is incorrectly applied to non-Arm cpus nodes. As we now have a common cpus schema which checks the general structure, it is also redundant to do so in the Arm CPU schema. The downside is one could conceivably mix different architecture's cpu nodes or have typos in the compatible string. The latter problem pretty much exists for every schema. Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: backlight: lm3630a: correct schema validationBrian Masney1-7/+14
The '#address-cells' and '#size-cells' properties were not defined in the lm3630a bindings and would cause the following error when attempting to validate the examples against the schema: Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.example.dt.yaml: '#address-cells', '#size-cells' do not match any of the regexes: '^led@[01]$', 'pinctrl-[0-9]+' Correct this by adding those two properties. While we're here, move the ti,linear-mapping-mode property to the led@[01] child nodes to correct the following validation error: Documentation/devicetree/bindings/leds/backlight/lm3630a-backlight.example.dt.yaml: led@0: 'ti,linear-mapping-mode' does not match any of the regexes: 'pinctrl-[0-9]+' Fixes: 32fcb75c66a0 ("dt-bindings: backlight: Add lm3630a bindings") Signed-off-by: Brian Masney <masneyb@onstation.org> Reported-by: Rob Herring <robh+dt@kernel.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Acked-by: Dan Murphy <dmurphy@ti.com> [robh: also drop maxItems from child reg] Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: net: dwmac: Deprecate the PHY reset propertiesMaxime Ripard1-0/+3
Even though the DWMAC driver uses some driver specific properties, the PHY core has a bunch of generic properties and can deal with them nicely. Let's deprecate our specific properties. Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: net: sun8i-emac: Convert the binding to a schemasMaxime Ripard3-201/+336
Switch our Allwinner H3 EMAC controller binding to a YAML schema to enable the DT validation. Since that controller is based on a Synopsys IP, let's add the validation to that schemas with a bunch of conditionals. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: net: sun7i-gmac: Convert the binding to a schemasMaxime Ripard3-27/+68
Switch our Allwinner A20 GMAC controller binding to a YAML schema to enable the DT validation. Since that controller is based on a Synopsys IP, let's add the validation to that schemas with a bunch of conditionals. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: net: stmmac: Convert the binding to a schemasMaxime Ripard2-178/+391
Switch the STMMAC / Synopsys DesignWare MAC controller binding to a YAML schema to enable the DT validation. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
2019-06-28dt-bindings: net: sun4i-mdio: Convert the binding to a schemasMaxime Ripard2-27/+70
Switch our Allwinner A10 MDIO controller binding to a YAML schema to enable the DT validation. Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Rob Herring <robh@kernel.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-21 23:48:05 +0300