| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
instead of cloning them. From Daniel Borkmann.
2) When converting classical BPF into eBPF, fix the setting of the
source reg to BPF_REG_X. From Tycho Andersen.
3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
Linus Lussing.
4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.
5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
Roopa Prabhu.
6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.
7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
Florian Westphal.
8) Check DMA mapping errors in bna driver, from Ivan Vecera.
9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
misclearing of interrupt status in TX timeout handler, etc.) from
David Woodhouse.
10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
Hugne.
11) Fix autobind races et al. in netlink code, from Herbert Xu with
help from Tejun Heo and others.
12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.
13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
Eric Dumazet.
14) Fix array overruns in mac80211, from Johannes Berg and Dan
Carpenter.
15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.
16) Fix race between poll_one_napi and napi_disable, from Neil Horman.
17) Fix byte order in geneve tunnel port config, from John W Linville.
18) Fix handling of ARP replies over lightweight tunnels, from Jiri
Benc.
19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
Kok and Roopa Prabhu.
20) Several reference count handling bug fixes in the PHY/MDIO layer
from Russel King.
21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.
22) Fix crash in icmp_route_lookup(), from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: Fix panic in icmp_route_lookup
net: update docbook comment for __mdiobus_register()
ppp: fix lockdep splat in ppp_dev_uninit()
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
phy: marvell: add link partner advertised modes
net: fix net_device refcounting
phy: add phy_device_remove()
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
net: fix phy refcounting in a bunch of drivers
of_mdio: fix MDIO phy device refcounting
phy: add proper phy struct device refcounting
phy: fix mdiobus module safety
net: dsa: fix of_mdio_find_bus() device refcount leak
phy: fix of_mdio_find_bus() device refcount leak
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
ip6_gre: Reduce log level in ip6gre_err() to debug
fib_rules: fix fib rule dumps across multiple skbs
bnx2x: byte swap rss_key to comply to Toeplitz specs
net: revert "net_sched: move tp->root allocation into fw_init()"
lwtunnel: remove source and destination UDP port config option
...
|
|
No longer need explicit modprobe's and update to use ip instead
of deprecated ifconfig command.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
|
|
Now, the memory allocation in prepare/commit state is done separatelly
in each driver (rocker). Introduce the similar mechanism in generic
switchdev code, in form of queue. That can be used not only for memory
allocations, but also for different items. Abort item destruction
is handled as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal management fixes from Zhang Rui:
- Power allocator governor changes to allow binding on thermal zones
with missing power estimates information. From Javi Merino.
- Add compile test flags on thermal drivers that allow it without
producing compilation errors. From Eduardo Valentin.
- Fixes around memory allocation on cpu_cooling. From Javi Merino.
- Fix on db8500 cpufreq code to allow autoload. From Luis de
Bethencourt.
- Maintainer entries for cpu cooling device
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: power_allocator: exit early if there are no cooling devices
thermal: power_allocator: don't require tzp to be present for the thermal zone
thermal: power_allocator: relax the requirement of two passive trip points
thermal: power_allocator: relax the requirement of a sustainable_power in tzp
thermal: Add a function to get the minimum power
thermal: cpu_cooling: free power table on error or when unregistering
thermal: cpu_cooling: don't call kcalloc() under rcu_read_lock
thermal: db8500_cpufreq_cooling: Fix module autoload for OF platform driver
thermal: cpu_cooling: Add MAINTAINERS entry
thermal: ti-soc: Kconfig fix to avoid menu showing wrongly
thermal: ti-soc: allow compile test
thermal: qcom_spmi: allow compile test
thermal: exynos: allow compile test
thermal: armada: allow compile test
thermal: dove: allow compile test
thermal: kirkwood: allow compile test
thermal: rockchip: allow compile test
thermal: spear: allow compile test
thermal: hisi: allow compile test
thermal: Fix thermal_zone_of_sensor_register to match documentation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
* tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: arm: Fix typo in the idle-states bindings examples
gpio: mention in DT binding doc that <name>-gpio is deprecated
of_pci_irq: Silence bogus "of_irq_parse_pci() failed ..." messages.
devicetree: bindings: Extend the bma180 bindings with bma250 info
of: thermal: Mark cooling-*-level properties optional
of: thermal: Fix inconsitency between cooling-*-state and cooling-*-level
Docs: dt: add #msi-cells to GICv3 ITS binding
of: add vendor prefix for Socionext Inc.
|
|
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The gpiolib supports parsing DT properties of the form <name>-gpio but it
was only added for compatibility with older DT bindings that got it wrong
and should not be used in newer bindings.
The commit that added support for this was:
dd34c37aa3e8 ("gpio: of: Allow -gpio suffix for property names")
but didn't update the documentation to explain this so it's been a source
of confusion. So let's make this clear in the GPIO DT binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A disappointingly large collection of fixes for SPI issues, though
almost all in drivers (and there mainly the newly added Mediatek
driver) and the core fixes are documentation and error handling.
The driver fixes are all of the usual 'important if you see them'
variety"
* tag 'spi-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: xtensa-xtfpga: fix register endianness
spi: meson: Fix module autoload for OF platform driver
spi: mediatek: fix wrong error return value on probe
spi: fix kernel-doc warnings in spi.h
spi: spidev: fix possible NULL dereference
spi: atmel: remove warning when !CONFIG_PM_SLEEP
spi: bcm2835: BUG: fix wrong use of PAGE_MASK
spi: mediatek: fix spi cs polarity error
spi: Fix documentation of spi_alloc_master()
spi: spi-pxa2xx: Check status register to determine if SSSR_TINT is disabled
spi: Mediatek: Document devicetree bindings update for spi bus
spi: mediatek: fix spi clock usage error
spi: mediatek: remove clk_disable_unprepare()
|
|
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next tree
in this 4.4 development cycle, they are:
1) Schedule ICMP traffic to IPVS instances, this introduces a new schedule_icmp
proc knob to enable/disable it. By default is off to retain the old
behaviour. Patchset from Alex Gartrell.
I'm also including what Alex originally said for the record:
"The configuration of ipvs at Facebook is relatively straightforward. All
ipvs instances bgp advertise a set of VIPs and the network prefers the
nearest one or uses ECMP in the event of a tie. For the uninitiated, ECMP
deterministically and statelessly load balances by hashing the packet
(usually a 5-tuple of protocol, saddr, daddr, sport, and dport) and using
that number as an index (basic hash table type logic).
The problem is that ICMP packets (which contain really important
information like whether or not an MTU has been exceeded) will get a
different hash value and may end up at a different ipvs instance. With no
information about where to route these packets, they are dropped, creating
ICMP black holes and breaking Path MTU discovery. Suddenly, my mom's
pictures can't load and I'm fielding midday calls that I want nothing to do
with.
To address this, this patch set introduces the ability to schedule icmp
packets which is gated by a sysctl net.ipv4.vs.schedule_icmp. If set to 0,
the old behavior is maintained -- otherwise ICMP packets are scheduled."
2) Add another proc entry to ignore tunneled packets to avoid routing loops
from IPVS, also from Alex.
3) Fifteen patches from Eric Biederman to:
* Stop passing nf_hook_ops as parameter to the hook and use the state hook
object instead all around the netfilter code, so only the private data
pointer is passed to the registered hook function.
* Now that we've got state->net, propagate the netns pointer to netfilter hook
clients to avoid its computation over and over again. A good example of how
this has been simplified is the former TEE target (now nf_dup infrastructure)
since it has killed the ugly pick_net() function.
There's another round of netns updates from Eric Biederman making the line. To
avoid the patchbomb again to almost all the networking mailing list (that is 84
patches) I'd suggest we send you a pull request with no patches or let me know
if you prefer a better way.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'spi/fix/doc', 'spi/fix/mediatek', 'spi/fix/meson', 'spi/fix/mtk' and 'spi/fix/pxa2xx' into spi-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-09-18
Here's the first bluetooth-next pull request for the 4.4 kernel:
- ieee802154 cleanups & fixes
- debugfs support for the at86rf230 driver
- Support for quirky (seemingly counterfeit) CSR Bluetooth controllers
- Power management and device config improvements for Intel controllers
- Fix for devices with incorrect advertising data length
- Fix for closing HCI user channel socket
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'regulator/fix/pbias', 'regulator/fix/tpx65218' and 'regulator/fix/vexpress' into regulator-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-09-17
this is a pull request of two patches for net-next/master.
Gerhard Bertelsmann adds support for the CAN controller found on the
Allwinner A10/A20 SoC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Hisilicon Network Subsystem is a long term evolution IP which is
supposed to be used in Hisilicon ICT SoC. The IP, which is called hns
for short, is a TCP/IP acceleration engine, which can directly decode
TCP/IP stream and distribute them to different ring buffers.
HNS can be configured to work on different mode for different scenario.
This patch make use only some of the mode to make it as standard
ethernet NIC. The other mode will be added soon.
The whole function has 4 kernel sub-modules:
hnae: the HNS acceleration engine framework. It provides a abstract
interface between the engine and the upper layers which make use of the
engine by ring buffer.
hns_enet_drv: a standard ethernet driver that base on the ring buffer.
hns_dsaf: one of the implementation of HNS acceleration engine, which is
applied on Hililicon hip05, Hi1610 and other later-on SoCs
hns_mdio: the mdio control to the PHY, used by acceleration engine
This submit add basic config and documents
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/ipvs-next
Simon Horman says:
====================
IPVS Updates for v4.4
please consider these IPVS Updates for v4.4.
The updates include the following from Alex Gartrell:
* Scheduling of ICMP
* Sysctl to ignore tunneled packets; and hence some packet-looping scenarios
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Aside from some lingual cleanup, point out which interfaces are not or
partly covered by this setting.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devicetree bindings for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The bma180 / bma250 accelerometers share a driver (at least under Linux),
so it makes sense to also have their bindings info in a single .txt.
This commit extends the bma180 bindings with bma250 bindings, specifically
it specifies how the 2 seperate interrupts the bma250 has must be listed
in devicetree. The existing bma180 driver is already fully compatible
with the specified bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The cooling-{min,max}-level properties are marked as optional in
Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt and the usage
in various device tree matches this, i.e., some cooling device in the
device trees provide these properties while others do not.
Make the bindings in
Documentation/devicetree/bindings/thermal/thermal.txt consistent with
the cpufreq-dt bindings by marking the cooling-*-level properties as
optional.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The device trees in the kernel as well as the binding description in
Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt use the
cooling-{min,max}-level property.
Fix the inconsistency with the binding description in
Documentation/devicetree/bindings/thermal/thermal.txt by changing
cooling-*-state properties to cooling-*-level.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The GICv3 ITS uses sideband master identification data (known as a
DeviceID) to identify which master wrote to a doorbell, and this data is
used to determine how to react in response to the write.
Commit 1e6db000482fa65a ("irqchip/gicv3-its: Add platform MSI support")
added support per this binding, but failed to update the documentation.
This patch fixes the documentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Ingo Molnar:
"Spinlock performance regression fix, plus documentation fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/static_keys: Fix up the static keys documentation
locking/qspinlock/x86: Only emit the test-and-set fallback when building guest support
locking/qspinlock/x86: Fix performance regression under unaccelerated VMs
locking/static_keys: Fix a silly typo
|
|
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This is a way to avoid nasty routing loops when multiple ipvs instances can
forward to eachother.
Signed-off-by: Alex Gartrell <agartrell@fb.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two patches for the nct6775 driver: add support for NCT6793D, and fix
swapped registers"
* tag 'hwmon-for-linus-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6775) Add support for NCT6793D
hwmon: (nct6775) Swap STEP_UP_TIME and STEP_DOWN_TIME registers for most chips
|
|
In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.
To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a few small mistakes in the static key documentation and
delete an unneeded sentence.
Suggested-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20150914171105.511e1e21@lwn.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The power allocator governor currently requires that the thermal zone
has at least two passive trip points. If there aren't, the governor
refuses to bind to the thermal zone.
This commit relaxes that requirement. Now the governor will bind to all
thermal zones regardless of how many trip points they have.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The GPIO documentation mentions that GPIOs are mapped by defining a
<function>-gpios property in the consumer device's node but a -gpio
sufix is also supported after commit:
dd34c37aa3e8 ("gpio: of: Allow -gpio suffix for property names")
Update the documentation to match the implementation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The con_id parameter has to match the GPIO description and is automatically
extended by the GPIO suffix if not NULL. I had to look into the code to
understand this and properly find the GPIO I've been looking for, so document
this.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
With commit 39b2bbe3d715 ("gpio: add flags argument to gpiod_get*()
functions") the gpiod_get*() functions got a 'flags' parameter. Reflect
this in the documentation, too.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
NCT6793D is register compatible with NCT6792D.
Also move nct6775_sio_names[] closer to enum kinds to simplify
adding new chips.
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux
Pull thermal updates from Zhang Rui:
- use int instead of unsigned long to represent temperature to avoid
bogus overheat detection when negative temperature reported. From
Sascha Hauer.
- export available thermal governors information to user space via
sysfs. From Wei Ni.
- introduce new thermal driver for Wildcat Point platform controller
hub, which uses PCH thermal sensor and associated critical and hot
trip points. From Tushar Dave.
- add suuport for Intel Skylake and Denlow platforms in powerclamp
driver.
- some small cleanups in thermal core.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: Add Intel PCH thermal driver
thermal: Add comment explaining test for critical temperature
thermal: Use IS_ENABLED instead of #ifdef
thermal: remove unnecessary call to thermal_zone_device_set_polling
thermal: trivial: fix typo in comment
thermal: consistently use int for temperatures
thermal: add available policies sysfs attribute
thermal/powerclamp: add cpu id for denlow platform
thermal/powerclamp: add cpu id for Skylake u/y
thermal/powerclamp: add cpu id for skylake h/s
|
|
Pull watchdog updates from Wim Van Sebroeck:
- new driver for NXP LPC18xx Watchdog Timer
- new driver for SAMA5D4 watchdog timer
- add support for MCP79 to nv_tco driver
- clean-up and improvement of the mpc8xxx watchdog driver
- improvements to gpio-wdt
- at91sam9_wdt clock improvements
... and other small fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
Watchdog: Fix parent of watchdog_devices
watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
watchdog: at91sam9: get and use slow clock
Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
watchdog: add a driver to support SAMA5D4 watchdog timer
watchdog: mpc8xxx: allow to compile for MPC512x
watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
watchdog: mpc8xxx: use dynamic memory for device specific data
watchdog: mpc8xxx: use devm_ioremap_resource to map memory
watchdog: mpc8xxx: make use of of_device_get_match_data
watchdog: mpc8xxx: simplify registration
watchdog: mpc8xxx: remove dead code
watchdog: lpc18xx_wdt_get_timeleft() can be static
DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
watchdog: NXP LPC18xx Watchdog Timer Driver
watchdog: gpio-wdt: ping already at startup for always running devices
watchdog: gpio-wdt: be more strict about hw_algo matching
Documentation: watchdog: at91sam9_wdt: add clocks property
watchdog: booke_wdt: Use infrastructure to check timeout limits
watchdog: (nv_tco) add support for MCP79
...
|
|
Prepare second round of input updates for 4.3 merge window.
|
|
Pull blk-cg updates from Jens Axboe:
"A bit later in the cycle, but this has been in the block tree for a a
while. This is basically four patchsets from Tejun, that improve our
buffered cgroup writeback. It was dependent on the other cgroup
changes, but they went in earlier in this cycle.
Series 1 is set of 5 patches that has cgroup writeback updates:
- bdi_writeback iteration fix which could lead to some wb's being
skipped or repeated during e.g. sync under memory pressure.
- Simplification of wb work wait mechanism.
- Writeback tracepoints updated to report cgroup.
Series 2 is is a set of updates for the CFQ cgroup writeback handling:
cfq has always charged all async IOs to the root cgroup. It didn't
have much choice as writeback didn't know about cgroups and there
was no way to tell who to blame for a given writeback IO.
writeback finally grew support for cgroups and now tags each
writeback IO with the appropriate cgroup to charge it against.
This patchset updates cfq so that it follows the blkcg each bio is
tagged with. Async cfq_queues are now shared across cfq_group,
which is per-cgroup, instead of per-request_queue cfq_data. This
makes all IOs follow the weight based IO resource distribution
implemented by cfq.
- Switched from GFP_ATOMIC to GFP_NOWAIT as suggested by Jeff.
- Other misc review points addressed, acks added and rebased.
Series 3 is the blkcg policy cleanup patches:
This patchset contains assorted cleanups for blkcg_policy methods
and blk[c]g_policy_data handling.
- alloc/free added for blkg_policy_data. exit dropped.
- alloc/free added for blkcg_policy_data.
- blk-throttle's async percpu allocation is replaced with direct
allocation.
- all methods now take blk[c]g_policy_data instead of blkcg_gq or
blkcg.
And finally, series 4 is a set of patches cleaning up the blkcg stats
handling:
blkcg's stats have always been somwhat of a mess. This patchset
tries to improve the situation a bit.
- The following patches added to consolidate blkcg entry point and
blkg creation. This is in itself is an improvement and helps
colllecting common stats on bio issue.
- per-blkg stats now accounted on bio issue rather than request
completion so that bio based and request based drivers can behave
the same way. The issue was spotted by Vivek.
- cfq-iosched implements custom recursive stats and blk-throttle
implements custom per-cpu stats. This patchset make blkcg core
support both by default.
- cfq-iosched and blk-throttle keep track of the same stats
multiple times. Unify them"
* 'for-4.3/blkcg' of git://git.kernel.dk/linux-block: (45 commits)
blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchy
blkcg: s/CFQ_WEIGHT_*/CFQ_WEIGHT_LEGACY_*/
blkcg: implement interface for the unified hierarchy
blkcg: misc preparations for unified hierarchy interface
blkcg: separate out tg_conf_updated() from tg_set_conf()
blkcg: move body parsing from blkg_conf_prep() to its callers
blkcg: mark existing cftypes as legacy
blkcg: rename subsystem name from blkio to io
blkcg: refine error codes returned during blkcg configuration
blkcg: remove unnecessary NULL checks from __cfqg_set_weight_device()
blkcg: reduce stack usage of blkg_rwstat_recursive_sum()
blkcg: remove cfqg_stats->sectors
blkcg: move io_service_bytes and io_serviced stats into blkcg_gq
blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gq
blkcg: make blkcg_[rw]stat per-cpu
blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with it
blkcg: consolidate blkg creation in blkcg_bio_issue_check()
blk-throttle: improve queue bypass handling
blkcg: move root blkg lookup optimization from throtl_lookup_tg() to __blkg_lookup()
blkcg: inline [__]blkg_lookup()
...
|
|
Merge third patch-bomb from Andrew Morton:
- even more of the rest of MM
- lib/ updates
- checkpatch updates
- small changes to a few scruffy filesystems
- kmod fixes/cleanups
- kexec updates
- a dma-mapping cleanup series from hch
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (81 commits)
dma-mapping: consolidate dma_set_mask
dma-mapping: consolidate dma_supported
dma-mapping: cosolidate dma_mapping_error
dma-mapping: consolidate dma_{alloc,free}_noncoherent
dma-mapping: consolidate dma_{alloc,free}_{attrs,coherent}
mm: use vma_is_anonymous() in create_huge_pmd() and wp_huge_pmd()
mm: make sure all file VMAs have ->vm_ops set
mm, mpx: add "vm_flags_t vm_flags" arg to do_mmap_pgoff()
mm: mark most vm_operations_struct const
namei: fix warning while make xmldocs caused by namei.c
ipc: convert invalid scenarios to use WARN_ON
zlib_deflate/deftree: remove bi_reverse()
lib/decompress_unlzma: Do a NULL check for pointer
lib/decompressors: use real out buf size for gunzip with kernel
fs/affs: make root lookup from blkdev logical size
sysctl: fix int -> unsigned long assignments in INT_MIN case
kexec: export KERNEL_IMAGE_SIZE to vmcoreinfo
kexec: align crash_notes allocation to make it be inside one physical page
kexec: remove unnecessary test in kimage_alloc_crash_control_pages()
kexec: split kexec_load syscall from kexec core code
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
|
|
Pull more kvm updates from Paolo Bonzini:
"ARM:
- Full debug support for arm64
- Active state switching for timer interrupts
- Lazy FP/SIMD save/restore for arm64
- Generic ARMv8 target
PPC:
- Book3S: A few bug fixes
- Book3S: Allow micro-threading on POWER8
x86:
- Compiler warnings
Generic:
- Adaptive polling for guest halt"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (49 commits)
kvm: irqchip: fix memory leak
kvm: move new trace event outside #ifdef CONFIG_KVM_ASYNC_PF
KVM: trace kvm_halt_poll_ns grow/shrink
KVM: dynamic halt-polling
KVM: make halt_poll_ns per-vCPU
Silence compiler warning in arch/x86/kvm/emulate.c
kvm: compile process_smi_save_seg_64() only for x86_64
KVM: x86: avoid uninitialized variable warning
KVM: PPC: Book3S: Fix typo in top comment about locking
KVM: PPC: Book3S: Fix size of the PSPB register
KVM: PPC: Book3S HV: Exit on H_DOORBELL if HOST_IPI is set
KVM: PPC: Book3S HV: Fix race in starting secondary threads
KVM: PPC: Book3S: correct width in XER handling
KVM: PPC: Book3S HV: Fix preempted vcore stolen time calculation
KVM: PPC: Book3S HV: Fix preempted vcore list locking
KVM: PPC: Book3S HV: Implement H_CLEAR_REF and H_CLEAR_MOD
KVM: PPC: Book3S HV: Fix bug in dirty page tracking
KVM: PPC: Book3S HV: Fix race in reading change bit when removing HPTE
KVM: PPC: Book3S HV: Implement dynamic micro-threading on POWER8
KVM: PPC: Book3S HV: Make use of unused threads when running guests
...
|
|
As noted by Minchan, a benefit of reading idle flag from /proc/kpageflags
is that one can easily filter dirty and/or unevictable pages while
estimating the size of unused memory.
Note that idle flag read from /proc/kpageflags may be stale in case the
page was accessed via a PTE, because it would be too costly to iterate
over all page mappings on each /proc/kpageflags read to provide an
up-to-date value. To make sure the flag is up-to-date one has to read
/sys/kernel/mm/page_idle/bitmap first.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Greg Thelen <gthelen@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Knowing the portion of memory that is not used by a certain application or
memory cgroup (idle memory) can be useful for partitioning the system
efficiently, e.g. by setting memory cgroup limits appropriately.
Currently, the only means to estimate the amount of idle memory provided
by the kernel is /proc/PID/{clear_refs,smaps}: the user can clear the
access bit for all pages mapped to a particular process by writing 1 to
clear_refs, wait for some time, and then count smaps:Referenced. However,
this method has two serious shortcomings:
- it does not count unmapped file pages
- it affects the reclaimer logic
To overcome these drawbacks, this patch introduces two new page flags,
Idle and Young, and a new sysfs file, /sys/kernel/mm/page_idle/bitmap.
A page's Idle flag can only be set from userspace by setting bit in
/sys/kernel/mm/page_idle/bitmap at the offset corresponding to the page,
and it is cleared whenever the page is accessed either through page tables
(it is cleared in page_referenced() in this case) or using the read(2)
system call (mark_page_accessed()). Thus by setting the Idle flag for
pages of a particular workload, which can be found e.g. by reading
/proc/PID/pagemap, waiting for some time to let the workload access its
working set, and then reading the bitmap file, one can estimate the amount
of pages that are not used by the workload.
The Young page flag is used to avoid interference with the memory
reclaimer. A page's Young flag is set whenever the Access bit of a page
table entry pointing to the page is cleared by writing to the bitmap file.
If page_referenced() is called on a Young page, it will add 1 to its
return value, therefore concealing the fact that the Access bit was
cleared.
Note, since there is no room for extra page flags on 32 bit, this feature
uses extended page flags when compiled on 32 bit.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: kpageidle requires an MMU]
[akpm@linux-foundation.org: decouple from page-flags rework]
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Greg Thelen <gthelen@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
/proc/kpagecgroup contains a 64-bit inode number of the memory cgroup each
page is charged to, indexed by PFN. Having this information is useful for
estimating a cgroup working set size.
The file is present if CONFIG_PROC_PAGE_MONITOR && CONFIG_MEMCG.
Signed-off-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: Andres Lagar-Cavilla <andreslc@google.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Raghavendra K T <raghavendra.kt@linux.vnet.ibm.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Greg Thelen <gthelen@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change the Documentation/vm/zswap.txt doc to indicate that the "zpool" and
"compressor" params are now changeable at runtime.
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
