Age | Commit message (Collapse) | Author | Files | Lines |
|
Oxford Semiconductor PCIe (Tornado) 950 serial port devices are driven
by a fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
We currently drive the device using its default oversampling rate of 16
and the clock prescaler disabled, consequently yielding the baud base of
3906250. This base is inadequate for some of the high-speed baud rates
such as 460800bps, for which the closest rate possible can be obtained
by dividing the baud base by 8, yielding the baud rate of 488281.25bps,
which is off by 5.9638%. This is enough for data communication to break
with the remote end talking actual 460800bps, where missed stop bits
have been observed.
We can do better however, by taking advantage of a reduced oversampling
rate, which can be set to any integer value from 4 to 16 inclusive by
programming the TCR register, and by using the clock prescaler, which
can be set to any value from 1 to 63.875 in increments of 0.125 in the
CPR/CPR2 register pair. The prescaler has to be explicitly enabled
though by setting bit 7 in the MCR or otherwise it is bypassed (in the
enhanced mode that we enable) as if the value of 1 was used.
Make use of these features then as follows:
- Set the baud base to 15625000, reflecting the minimum oversampling
rate of 4 with the clock prescaler and divisor both set to 1.
- Override the `set_mctrl' and set the MCR shadow there so as to have
MCR[7] always set and have the 8250 core propagate these settings.
- Override the `get_divisor' handler and determine a good combination of
parameters by using a lookup table with predetermined value pairs of
the oversampling rate and the clock prescaler and finding a pair that
divides the input clock such that the quotient, when rounded to the
nearest integer, deviates the least from the exact result. Calculate
the clock divisor accordingly.
Scale the resulting oversampling rate (only by powers of two) if
possible so as to maximise it, reducing the divisor accordingly, and
avoid a divisor overflow for very low baud rates by scaling the
oversampling rate and/or the prescaler even if that causes some
accuracy loss.
Also handle the historic spd_cust feature so as to allow one to set
all the three parameters manually to arbitrary values, by keeping the
low 16 bits for the divisor and then putting TCR in bits 19:16 and
CPR/CPR2 in bits 28:20, sanitising the bit pattern supplied such as
to clamp CPR/CPR2 values between 0.000 and 0.875 inclusive to 33.875.
This preserves compatibility with any existing setups, that is where
requesting a custom divisor that only has any bits set among the low
16 the oversampling rate of 16 and the clock prescaler of 33.875 will
be used as with the original 8250.
Finally abuse the `frac' argument to store the determined bit patterns
for the TCR, CPR and CPR2 registers.
- Override the `set_divisor' handler so as to set the TCR, CPR and CPR2
registers from the `frac' value supplied. Set the divisor as usual.
With the baud base set to 15625000 and the unsigned 16-bit UART_DIV_MAX
limitation imposed by `serial8250_get_baud_rate' standard baud rates
below 300bps become unavailable in the regular way, e.g. the rate of
200bps requires the baud base to be divided by 78125 and that is beyond
the unsigned 16-bit range. The historic spd_cust feature can still be
used to obtain such rates if so required.
See Documentation/tty/device_drivers/oxsemi-tornado.rst for more details.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181519450.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/c57ed00e85778380776330be6183c6861d843c22.1651497024.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Despite the name, R-Car V3U is the first member of the R-Car Gen4
family. Hence move its compatible value to the R-Car Gen4 section.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/dd734aaa4e5e0b32864b038b79eafe72907fb99f.1651497024.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Take care of faults occuring between the PARange and IPA range by
injecting an exception
- Fix S2 faults taken from a host EL0 in protected mode
- Work around Oops caused by a PMU access from a 32bit guest when PMU
has been created. This is a temporary bodge until we fix it for
good.
x86:
- Fix potential races when walking host page table
- Fix shadow page table leak when KVM runs nested
- Work around bug in userspace when KVM synthesizes leaf 0x80000021
on older (pre-EPYC) or Intel processors
Generic (but affects only RISC-V):
- Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: work around QEMU issue with synthetic CPUID leaves
Revert "x86/mm: Introduce lookup_address_in_mm()"
KVM: x86/mmu: fix potential races when walking host page table
KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
KVM: arm64: Inject exception on out-of-IPA-range translation fault
KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set
KVM: arm64: Handle host stage-2 faults from 32-bit EL0
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB driver fixes for 5.18-rc5 for some
reported issues and new quirks. They include:
- dwc3 driver fixes
- xhci driver fixes
- typec driver fixes
- new usb-serial driver ids
- added new USB devices to existing quirk tables
- other tiny fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (31 commits)
usb: phy: generic: Get the vbus supply
usb: dwc3: gadget: Return proper request status
usb: dwc3: pci: add support for the Intel Meteor Lake-P
usb: dwc3: core: Only handle soft-reset in DCTL
usb: gadget: configfs: clear deactivation flag in configfs_composite_unbind()
usb: misc: eud: Fix an error handling path in eud_probe()
usb: core: Don't hold the device lock while sleeping in do_proc_control()
usb: dwc3: Try usb-role-switch first in dwc3_drd_init
usb: dwc3: core: Fix tx/rx threshold settings
usb: mtu3: fix USB 3.0 dual-role-switch from device to host
xhci: Enable runtime PM on second Alderlake controller
usb: dwc3: fix backwards compat with rockchip devices
dt-bindings: usb: samsung,exynos-usb2: add missing required reg
usb: misc: fix improper handling of refcount in uss720_probe()
USB: Fix ehci infinite suspend-resume loop issue in zhaoxin
usb: typec: tcpm: Fix undefined behavior due to shift overflowing the constant
usb: typec: rt1719: Fix build error without CONFIG_POWER_SUPPLY
usb: typec: ucsi: Fix role swapping
usb: typec: ucsi: Fix reuse of completion structure
usb: xhci: tegra:Fix PM usage reference leak of tegra_xusb_unpowergate_partitions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
- A fix for a regression caused by the previous set of bugfixes
changing tegra and at91 pinctrl properties.
More work is needed to figure out what this should actually be, but a
revert makes it work for the moment.
- Defconfig regression fixes for tegra after renamed symbols
- Build-time warning and static checker fixes for imx, op-tee, sunxi,
meson, at91, and omap
- More at91 DT fixes for audio, regulator and spi nodes
- A regression fix for Renesas Hyperflash memory probe
- A stability fix for amlogic boards, modifying the allowed cpufreq
states
- Multiple fixes for system suspend on omap2+
- DT fixes for various i.MX bugs
- A probe error fix for imx6ull-colibri MMC
- A MAINTAINERS file entry for samsung bug reports
* tag 'soc-fixes-5.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
Revert "arm: dts: at91: Fix boolean properties with values"
bus: sunxi-rsb: Fix the return value of sunxi_rsb_device_create()
Revert "arm64: dts: tegra: Fix boolean properties with values"
arm64: dts: imx8mn-ddr4-evk: Describe the 32.768 kHz PMIC clock
ARM: dts: imx6ull-colibri: fix vqmmc regulator
MAINTAINERS: add Bug entry for Samsung and memory controller drivers
memory: renesas-rpc-if: Fix HF/OSPI data transfer in Manual Mode
ARM: dts: logicpd-som-lv: Fix wrong pinmuxing on OMAP35
ARM: dts: am3517-evm: Fix misc pinmuxing
ARM: dts: am33xx-l4: Add missing touchscreen clock properties
ARM: dts: Fix mmc order for omap3-gta04
ARM: dts: at91: fix pinctrl phandles
ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
ARM: dts: at91: Describe regulators on at91sam9g20ek
ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
ARM: dts: at91: Fix boolean properties with values
ARM: dts: at91: use generic node name for dataflash
ARM: dts: at91: align SPI NOR node name with dtschema
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A semi-large pile of clk driver fixes this time around.
Nothing is touching the core so these fixes are fairly well contained
to specific devices that use these clk drivers.
- Some Allwinner SoC fixes to gracefully handle errors and mark an
RTC clk as critical so that the RTC keeps ticking.
- Fix AXI bus clks and RTC clk design for Microchip PolarFire SoC
driver introduced this cycle. This has some devicetree bits acked
by riscv maintainers. We're fixing it now so that the prior
bindings aren't released in a major kernel version.
- Remove a reset on Microchip PolarFire SoCs that broke when enabling
CONFIG_PM.
- Set a min/max for the Qualcomm graphics clk. This got broken by the
clk rate range patches introduced this cycle"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: sunxi: sun9i-mmc: check return value after calling platform_get_resource()
clk: sunxi-ng: sun6i-rtc: Mark rtc-32k as critical
riscv: dts: microchip: reparent mpfs clocks
clk: microchip: mpfs: add RTCREF clock control
clk: microchip: mpfs: re-parent the configurable clocks
dt-bindings: rtc: add refclk to mpfs-rtc
dt-bindings: clk: mpfs: add defines for two new clocks
dt-bindings: clk: mpfs document msspll dri registers
riscv: dts: microchip: fix usage of fic clocks on mpfs
clk: microchip: mpfs: mark CLK_ATHENA as critical
clk: microchip: mpfs: fix parents for FIC clocks
clk: qcom: clk-rcg2: fix gfx3d frequency calculation
clk: microchip: mpfs: don't reset disabled peripherals
clk: sunxi-ng: fix not NULL terminated coccicheck error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Eric noticed that the memmove() in crng_fast_key_erasure() was bogus,
so this has been changed to a memcpy() and the confusing situation
clarified with a detailed comment.
- [Half]SipHash documentation updates from Bagas and Eric, after Eric
pointed out that the use of HalfSipHash in random.c made a bit of the
text potentially misleading.
* tag 'random-5.18-rc5-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
Documentation: siphash: disambiguate HalfSipHash algorithm from hsiphash functions
Documentation: siphash: enclose HalfSipHash usage example in the literal block
Documentation: siphash: convert danger note to warning for HalfSipHash
random: document crng_fast_key_erasure() destination possibility
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Rename and reallocate the PT_ARM_MEMTAG_MTE ELF segment type.
This is a fix to the MTE ELF ABI for a bug that was added during the
most recent merge window as part of the coredump support.
The issue is that the value assigned to the new PT_ARM_MEMTAG_MTE
segment type has already been allocated to PT_AARCH64_UNWIND by the
ELF ABI, so we've bumped the value and changed the name of the
identifier to be better aligned with the existing one"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
elf: Fix the arm64 MTE ELF segment name and value
|
|
Fixes for (relatively) old bugs, to be merged in both the -rc and next
development trees:
* Fix potential races when walking host page table
* Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
* Fix shadow page table leak when KVM runs nested
|
|
When KVM_EXIT_SYSTEM_EVENT was introduced, it included a flags
member that at the time was unused. Unfortunately this extensibility
mechanism has several issues:
- x86 is not writing the member, so it would not be possible to use it
on x86 except for new events
- the member is not aligned to 64 bits, so the definition of the
uAPI struct is incorrect for 32- on 64-bit userspace. This is a
problem for RISC-V, which supports CONFIG_KVM_COMPAT, but fortunately
usage of flags was only introduced in 5.18.
Since padding has to be introduced, place a new field in there
that tells if the flags field is valid. To allow further extensibility,
in fact, change flags to an array of 16 values, and store how many
of the values are valid. The availability of the new ndata field
is tied to a system capability; all architectures are changed to
fill in the field.
To avoid breaking compilation of userspace that was using the flags
field, provide a userspace-only union to overlap flags with data[0].
The new field is placed at the same offset for both 32- and 64-bit
userspace.
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Peter Gonda <pgonda@google.com>
Cc: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Message-Id: <20220422103013.34832-1-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and netfilter.
Current release - new code bugs:
- bridge: switchdev: check br_vlan_group() return value
- use this_cpu_inc() to increment net->core_stats, fix preempt-rt
Previous releases - regressions:
- eth: stmmac: fix write to sgmii_adapter_base
Previous releases - always broken:
- netfilter: nf_conntrack_tcp: re-init for syn packets only,
resolving issues with TCP fastopen
- tcp: md5: fix incorrect tcp_header_len for incoming connections
- tcp: fix F-RTO may not work correctly when receiving DSACK
- tcp: ensure use of most recently sent skb when filling rate samples
- tcp: fix potential xmit stalls caused by TCP_NOTSENT_LOWAT
- virtio_net: fix wrong buf address calculation when using xdp
- xsk: fix forwarding when combining copy mode with busy poll
- xsk: fix possible crash when multiple sockets are created
- bpf: lwt: fix crash when using bpf_skb_set_tunnel_key() from
bpf_xmit lwt hook
- sctp: null-check asoc strreset_chunk in sctp_generate_reconf_event
- wireguard: device: check for metadata_dst with skb_valid_dst()
- netfilter: update ip6_route_me_harder to consider L3 domain
- gre: make o_seqno start from 0 in native mode
- gre: switch o_seqno to atomic to prevent races in collect_md mode
Misc:
- add Eric Dumazet to networking maintainers
- dt: dsa: realtek: remove realtek,rtl8367s string
- netfilter: flowtable: Remove the empty file"
* tag 'net-5.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (65 commits)
tcp: fix F-RTO may not work correctly when receiving DSACK
Revert "ibmvnic: Add ethtool private flag for driver-defined queue limits"
net: enetc: allow tc-etf offload even with NETIF_F_CSUM_MASK
ixgbe: ensure IPsec VF<->PF compatibility
MAINTAINERS: Update BNXT entry with firmware files
netfilter: nft_socket: only do sk lookups when indev is available
net: fec: add missing of_node_put() in fec_enet_init_stop_mode()
bnx2x: fix napi API usage sequence
tls: Skip tls_append_frag on zero copy size
Add Eric Dumazet to networking maintainers
netfilter: conntrack: fix udp offload timeout sysctl
netfilter: nf_conntrack_tcp: re-init for syn packets only
net: dsa: lantiq_gswip: Don't set GSWIP_MII_CFG_RMII_CLK
net: Use this_cpu_inc() to increment net->core_stats
Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted
Bluetooth: hci_event: Fix creating hci_conn object on error status
Bluetooth: hci_event: Fix checking for invalid handle on error status
ice: fix use-after-free when deinitializing mailbox snapshot
ice: wait 5 s for EMP reset after firmware flash
ice: Protect vf_state check by cfg_lock in ice_vc_process_vf_msg()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"A minor fix for the DT binding documentation of the rt5190a driver"
* tag 'regulator-fix-v5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: dt-bindings: Revise the rt5190a buck/ldo description
|
|
Unfortunately, the name/value choice for the MTE ELF segment type
(PT_ARM_MEMTAG_MTE) was pretty poor: LOPROC+1 is already in use by
PT_AARCH64_UNWIND, as defined in the AArch64 ELF ABI
(https://github.com/ARM-software/abi-aa/blob/main/aaelf64/aaelf64.rst).
Update the ELF segment type value to LOPROC+2 and also change the define
to PT_AARCH64_MEMTAG_MTE to match the AArch64 ELF ABI namespace. The
AArch64 ELF ABI document is updating accordingly (segment type not
previously mentioned in the document).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 761b9b366cec ("elf: Introduce the ARM MTE ELF segment type")
Cc: Will Deacon <will@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Luis Machado <luis.machado@arm.com>
Cc: Richard Earnshaw <Richard.Earnshaw@arm.com>
Link: https://lore.kernel.org/r/20220425151833.2603830-1-catalin.marinas@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Sphinx generates hard-to-read lists of parameters at the bottom of the
page. Fix them by putting literal-block markers of "::" in front of
them.
Link: https://lkml.kernel.org/r/cfd3bcc0-b51d-0c68-c065-ca1c4c202447@gmail.com
Signed-off-by: Akira Yokosawa <akiyks@gmail.com>
Fixes: 57f2b54a9379 ("Documentation/vm/page_owner.rst: update the documentation")
Cc: Shenghong Han <hanshenghong2019@email.szu.edu.cn>
Cc: Haowen Bai <baihaowen@meizu.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Alex Shi <seakeel@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Document RS485 related properties returned from ACPI _DSD as device
properties.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220426122448.38997-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add polarity property for receiver enable. Some UARTs have separate
enable pins for tx (RTS or DE) and rx (RE). As most RS485 transceivers
have !RE pin, the default is active low in contrast to
rs485-rts-active-low that defaults to active high.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220426122448.38997-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
R-Car V4H (R8A779G0) SoC has the R-Car Gen4 compatible HSCIF ports,
so document the SoC specific bindings.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220425064201.459633-4-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs fixes from Jaegeuk Kim:
"This includes major bug fixes introduced in 5.18-rc1 and 5.17+:
- Remove obsolete whint_mode (5.18-rc1)
- Fix IO split issue caused by op_flags change in f2fs (5.18-rc1)
- Fix a wrong condition check to detect IO failure loop (5.18-rc1)
- Fix wrong data truncation during roll-forward (5.17+)"
* tag 'f2fs-fix-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: should not truncate blocks during roll-forward recovery
f2fs: fix wrong condition check when failing metapage read
f2fs: keep io_flags to avoid IO split due to different op_flags in two fio holders
f2fs: remove obsolete whint_mode
|
|
functions
Fix the documentation for the hsiphash functions to avoid conflating the
HalfSipHash algorithm with the hsiphash functions, since these functions
actually implement either HalfSipHash or SipHash, and random.c now uses
HalfSipHash (in a very special way) without the hsiphash functions.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Render usage example of HalfSipHash function as code block by using
literal block syntax.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
Render danger paragraph into warning block for emphasization.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
The rtc on PolarFire SoC does not use the AHB clock as its reference
frequency, but rather a 1 MHz refclk that it shares with MTIMER. Add
this second clock to the binding as a required property.
Fixes: 4cbcc0d7b397 ("dt-bindings: rtc: add bindings for microchip mpfs rtc")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-7-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
As there are two sections of registers that are responsible for clock
configuration on the PolarFire SoC: add the dynamic reconfiguration
interface section to the binding & describe what each of the sections
are used for.
Fixes: 2145bb687e3f ("dt-bindings: clk: microchip: Add Microchip PolarFire host binding")
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220413075835.3354193-5-conor.dooley@microchip.com
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Fix some syzbot-detected bugs, as well as other bugs found by I/O
injection testing.
Change ext4's fallocate to consistently drop set[ug]id bits when an
fallocate operation might possibly change the user-visible contents of
a file.
Also, improve handling of potentially invalid values in the the
s_overhead_cluster superblock field to avoid ext4 returning a negative
number of free blocks"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
jbd2: fix a potential race while discarding reserved buffers after an abort
ext4: update the cached overhead value in the superblock
ext4: force overhead calculation if the s_overhead_cluster makes no sense
ext4: fix overhead calculation to account for the reserved gdt blocks
ext4, doc: fix incorrect h_reserved size
ext4: limit length to bitmap_maxbytes - blocksize in punch_hole
ext4: fix use-after-free in ext4_search_dir
ext4: fix bug_on in start_this_handle during umount filesystem
ext4: fix symlink file size not match to file content
ext4: fix fallocate to use file_modified to update permissions consistently
|
|
Compatible strings are used to help the driver find the chip ID/version
register for each chip family. After that, the driver can setup the
switch accordingly. Keep only the first supported model for each family
as a compatible string and reference other chip models in the
description.
The removed compatible strings have never been used in a released kernel.
Link: https://lore.kernel.org/netdev/20220414014055.m4wbmr7tdz6hsa3m@bang-olufsen.dk/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20220418233558.13541-1-luizluca@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Revise the rt5190a bucks and ldo property description.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Link: https://lore.kernel.org/r/1650610255-6180-1-git-send-email-u0084500@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine fixes from Vinod Koul:
"A bunch of driver fixes:
- idxd device RO checks and device cleanup
- dw-edma unaligned access and alignment
- qcom: missing minItems in binding
- mediatek pm usage fix
- imx init script"
* tag 'dmaengine-fix-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine:
dt-bindings: dmaengine: qcom: gpi: Add minItems for interrupts
dmaengine: idxd: skip clearing device context when device is read-only
dmaengine: idxd: add RO check for wq max_transfer_size write
dmaengine: idxd: add RO check for wq max_batch_size write
dmaengine: idxd: fix retry value to be constant for duration of function call
dmaengine: idxd: match type for retries var in idxd_enqcmds()
dmaengine: dw-edma: Fix inconsistent indenting
dmaengine: dw-edma: Fix unaligned 64bit access
dmaengine: mediatek:Fix PM usage reference leak of mtk_uart_apdma_alloc_chan_resources
dmaengine: imx-sdma: Fix error checking in sdma_event_remap
dma: at_xdmac: fix a missing check on list iterator
dmaengine: imx-sdma: fix init of uart scripts
dmaengine: idxd: fix device cleanup on disable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from xfrm and can.
Current release - regressions:
- rxrpc: restore removed timer deletion
Current release - new code bugs:
- gre: fix device lookup for l3mdev use-case
- xfrm: fix egress device lookup for l3mdev use-case
Previous releases - regressions:
- sched: cls_u32: fix netns refcount changes in u32_change()
- smc: fix sock leak when release after smc_shutdown()
- xfrm: limit skb_page_frag_refill use to a single page
- eth: atlantic: invert deep par in pm functions, preventing null
derefs
- eth: stmmac: use readl_poll_timeout_atomic() in atomic state
Previous releases - always broken:
- gre: fix skb_under_panic on xmit
- openvswitch: fix OOB access in reserve_sfa_size()
- dsa: hellcreek: calculate checksums in tagger
- eth: ice: fix crash in switchdev mode
- eth: igc:
- fix infinite loop in release_swfw_sync
- fix scheduling while atomic"
* tag 'net-5.18-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (37 commits)
drivers: net: hippi: Fix deadlock in rr_close()
selftests: mlxsw: vxlan_flooding_ipv6: Prevent flooding of unwanted packets
selftests: mlxsw: vxlan_flooding: Prevent flooding of unwanted packets
nfc: MAINTAINERS: add Bug entry
net: stmmac: Use readl_poll_timeout_atomic() in atomic state
doc/ip-sysctl: add bc_forwarding
netlink: reset network and mac headers in netlink_dump()
net: mscc: ocelot: fix broken IP multicast flooding
net: dsa: hellcreek: Calculate checksums in tagger
net: atlantic: invert deep par in pm functions, preventing null derefs
can: isotp: stop timeout monitoring when no first frame was sent
bonding: do not discard lowest hash bit for non layer3+4 hashing
net: lan966x: Make sure to release ptp interrupt
ipv6: make ip6_rt_gc_expire an atomic_t
net: Handle l3mdev in ip_tunnel_init_flow
l3mdev: l3mdev_master_upper_ifindex_by_index_rcu should be using netdev_master_upper_dev_get_rcu
net/sched: cls_u32: fix possible leak in u32_init_knode()
net/sched: cls_u32: fix netns refcount changes in u32_change()
powerpc: Update MAINTAINERS for ibmvnic and VAS
net: restore alpha order to Ethernet devices in config
...
|
|
"reg" property is required on Samsung S5PV210/Exynos EHCI/OHCI
controllers.
Fixes: 4bf2283cb208 ("dt-bindings: usb: samsung,exynos-usb2: convert to dtschema")
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20220407192338.14849-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs
Pull erofs fixes from Gao Xiang:
"One patch to fix a use-after-free race related to the on-stack
z_erofs_decompressqueue, which happens very rarely but needs to be
fixed properly soon.
The other patch fixes some sysfs Sphinx warnings"
* tag 'erofs-for-5.18-rc4-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
Documentation/ABI: sysfs-fs-erofs: Fix Sphinx errors
erofs: fix use-after-free of on-stack io[]
|
|
This patch removes obsolete whint_mode.
Fixes: 41d36a9f3e53 ("fs: remove kiocb.ki_hint")
Reviewed-by: Chao Yu <chao@kernel.org>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
The commit below causes the following warnings:
Documentation/driver-api/index.rst:14: WARNING: toctree contains reference to nonexisting document 'driver-api/tty'
Documentation/driver-api/tty/index.rst: WARNING: document isn't included in any toctree
This is because I omitted the "/index" part from the link. That part is
needed for directories and I was confused by the surrounding links which
are links to files. Fix it in this patch.
Fixes: b96cd8b05ead ("Documentation: move tty to driver-api")
Cc: Jonathan Corbet <corbet@lwn.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220419074302.29632-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the minItems for interrupts property as well. In the absence of
this, we get warning if interrupts are less than 13
arch/arm64/boot/dts/qcom/qrb5165-rb5.dtb:
dma-controller@800000: interrupts: [[0, 588, 4], [0, 589, 4], [0, 590,
4], [0, 591, 4], [0, 592, 4], [0, 593, 4], [0, 594, 4], [0, 595, 4], [0,
596, 4], [0, 597, 4]] is too short
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220414064235.1182195-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Let's describe this sysctl.
Fixes: 5cbf777cfdf6 ("route: add support for directed broadcast forwarding")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Fix scalar property schemas with array constraints
- Fix 'enum' lists with duplicate entries
- Fix incomplete if/then/else schemas
- Add Renesas RZ/V2L SoC support to Mali Bifrost binding
- Maintainers update for Marvell irqchip
* tag 'devicetree-fixes-for-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: display: panel-timing: Define a single type for properties
dt-bindings: Fix array constraints on scalar properties
dt-bindings: gpu: mali-bifrost: Document RZ/V2L SoC
dt-bindings: net: snps: remove duplicate name
dt-bindings: Fix 'enum' lists with duplicate entries
dt-bindings: irqchip: mrvl,intc: refresh maintainers
dt-bindings: Fix incomplete if/then/else schemas
dt-bindings: power: renesas,apmu: Fix cpus property limits
dt-bindings: extcon: maxim,max77843: fix ports type
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of SoC bugfixes that came in since the merge
window, and more of them are already pending.
This batch includes:
- A boot time regression fix for davinci that triggered on
multi_v5_defconfig when booting any platform
- Defconfig updates to address removed features, changed symbol names
or dependencies, for gemini, ux500, and pxa
- Email address changes for Krzysztof Kozlowski
- Build warning fixes for ep93xx and iop32x
- Devicetree warning fixes across many platforms
- Minor bugfixes for the reset controller, memory controller and SCMI
firmware subsystems plus the versatile-express board"
* tag 'soc-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
ARM: config: Update Gemini defconfig
arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
ARM: dts: align SPI NOR node name with dtschema
ARM: dts: Fix more boolean properties with values
arm/arm64: dts: qcom: Fix boolean properties with values
arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
arm: dts: imx: Fix boolean properties with values
arm64: dts: tegra: Fix boolean properties with values
arm: dts: at91: Fix boolean properties with values
arm: configs: imote2: Drop defconfig as board support dropped.
ep93xx: clock: Don't use plain integer as NULL pointer
ep93xx: clock: Fix UAF in ep93xx_clk_register_gate()
ARM: vexpress/spc: Fix all the kernel-doc build warnings
ARM: vexpress/spc: Fix kernel-doc build warning for ve_spc_cpu_in_wfi
ARM: config: u8500: Re-enable AB8500 battery charging
ARM: config: u8500: Add some common hardware
memory: fsl_ifc: populate child nodes of buses and mfd devices
ARM: config: Refresh U8500 defconfig
firmware: arm_scmi: Fix sparse warnings in OPTEE transport driver
firmware: arm_scmi: Replace zero-length array with flexible-array member
...
|
|
Fix the following warnings from "make htmldocs":
Documentation/ABI/testing/sysfs-fs-erofs:10:
ERROR: Unexpected indentation.
WARNING: Block quote ends without a blank line; unexpected unindent.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20220324165918.22005-4-hdegoede@redhat.com
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
|
|
Similar to I2C controller, move geni based QUP UART controller binding
out from parent schema to an individual binding and let parent refer to
child schema later on. UART binding also stand incomplete right now
similar to I2C, complete it along this process.
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220404182938.29492-4-singh.kuldeep87k@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Renesas RZ/V2M (r9a09g011) SoC uses a uart that is compatible with the
EMMA Mobile SoC.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220330154024.112270-3-phil.edworthy@renesas.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The lpuart on i.MX93 is derived from i.MX7ULP with some industrial
enhancements, it uses two compatible strings, so update the
compatible string for i.MX93.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220323093659.1722463-1-peng.fan@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UniPhier UART controller has a reset lines from system controller.
Add "resets" property to fix the following warning.
uniphier-ld11-global.dtb: serial@54006800: 'resets' does not match any of the regexes: 'pinctrl-[0-9]+'
From schema: Documentation/devicetree/bindings/serial/socionext,uniphier-uart.yaml
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1648617338-8600-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'maxItems' is preferred for a single entry, not 'minItems'.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1648617338-8600-2-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull drm fixes from Dave Airlie:
"Eggs season holidays are among us, and I think I'd expect some smaller
pulls for two weeks then.
This seems eerily quiet. One i915 fix, amdgpu has a bunch and msm. I
didn't see a misc pull this week, so I expect that will catch up next
week.
i915:
- Correct legacy mmap disabling to use GRAPHICS_VER_FULL
msm:
- system suspend fix
- kzalloc return checks
- misc display fix
- iommu_present removal
amdgpu:
- Fix for alpha properly in pre-multiplied mode
- Fix VCN 3.1.2 firmware name
- Suspend/resume fix
- Add a gfxoff quirk for Mac vega20 board
- DCN 3.1.6 spread spectrum fix"
* tag 'drm-fixes-2022-04-15' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: remove dtbclk_ss compensation for dcn316
drm/amdgpu: Enable gfxoff quirk on MacBook Pro
drm/amdgpu: Ensure HDA function is suspended before ASIC reset
drm/amdgpu: fix VCN 3.1.2 firmware name
drm/amd/display: don't ignore alpha property on pre-multiplied mode
drm/msm/gpu: Avoid -Wunused-function with !CONFIG_PM_SLEEP
drm/msm/dp: add fail safe mode outside of event_mutex context
drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()
drm/msm: Stop using iommu_present()
drm/msm/mdp5: check the return of kzalloc()
drm/msm: Fix range size vs end confusion
drm/i915: Sunset igpu legacy mmap support based on GRAPHICS_VER_FULL
drm/msm/dpu: Use indexed array initializer to prevent mismatches
drm/msm/disp: check the return value of kzalloc()
dt-bindings: display/msm: another fix for the dpu-qcm2290 example
drm/msm: Add missing put_task_struct() in debugfs path
drm/msm/gpu: Remove mutex from wait_event condition
drm/msm/gpu: Park scheduler threads for system suspend
drm/msm/gpu: Rename runtime suspend/resume functions
|
|
It's not good practice to define multiple types for the same property, so
factor out the type reference making the properties always an uint32-array
with a length of 1 or 3 items.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://lore.kernel.org/r/20220413140016.3131013-1-robh@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux into arm/fixes
AT91 fixes #1 for 5.18:
Only DT fixes. They cover syntax issues as well as features:
- fix dtschema check warnings for DMA channel entries, boolean
properties and flash names
- sam9g20ek audio clock and regulator description
- sama5d[34]_xplained SPI pinctrl
- align DT with hardware subtleties on sama7g5ek
* tag 'at91-fixes-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux:
ARM: dts: at91: fix pinctrl phandles
ARM: dts: at91: sama5d4_xplained: fix pinctrl phandle name
ARM: dts: at91: Describe regulators on at91sam9g20ek
ARM: dts: at91: Map MCLK for wm8731 on at91sam9g20ek
ARM: dts: at91: Fix boolean properties with values
ARM: dts: at91: use generic node name for dataflash
ARM: dts: at91: align SPI NOR node name with dtschema
ARM: dts: at91: sama7g5ek: Align the impedance of the QSPI0's HSIO and PCB lines
ARM: dts: at91: sama7g5ek: enable pull-up on flexcom3 console lines
ARM: dts: at91: sama7g5: Swap `rx` and `tx` for `i2c` nodes
Link: https://lore.kernel.org/r/20220414143318.26363-1-nicolas.ferre@microchip.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from wireless and netfilter.
Current release - regressions:
- smc: fix af_ops of child socket pointing to released memory
- wifi: ath9k: fix usage of driver-private space in tx_info
Previous releases - regressions:
- ipv6: fix panic when forwarding a pkt with no in6 dev
- sctp: use the correct skb for security_sctp_assoc_request
- smc: fix NULL pointer dereference in smc_pnet_find_ib()
- sched: fix initialization order when updating chain 0 head
- phy: don't defer probe forever if PHY IRQ provider is missing
- dsa: revert "net: dsa: setup master before ports"
- dsa: felix: fix tagging protocol changes with multiple CPU ports
- eth: ice:
- fix use-after-free when freeing @rx_cpu_rmap
- revert "iavf: fix deadlock occurrence during resetting VF
interface"
- eth: lan966x: stop processing the MAC entry is port is wrong
Previous releases - always broken:
- sched:
- flower: fix parsing of ethertype following VLAN header
- taprio: check if socket flags are valid
- nfc: add flush_workqueue to prevent uaf
- veth: ensure eth header is in skb's linear part
- eth: stmmac: fix altr_tse_pcs function when using a fixed-link
- eth: macb: restart tx only if queue pointer is lagging
- eth: macvlan: fix leaking skb in source mode with nodst option"
* tag 'net-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
rtnetlink: Fix handling of disabled L3 stats in RTM_GETSTATS replies
net: dsa: felix: fix tagging protocol changes with multiple CPU ports
tun: annotate access to queue->trans_start
nfc: nci: add flush_workqueue to prevent uaf
net: dsa: realtek: don't parse compatible string for RTL8366S
net: dsa: realtek: fix Kconfig to assure consistent driver linkage
net: ftgmac100: access hardware register after clock ready
Revert "net: dsa: setup master before ports"
macvlan: Fix leaking skb in source mode with nodst option
netfilter: nf_tables: nft_parse_register can return a negative value
net: lan966x: Stop processing the MAC entry is port is wrong.
net: lan966x: Fix when a port's upper is changed.
net: lan966x: Fix IGMP snooping when frames have vlan tag
net: lan966x: Update lan966x_ptp_get_nominal_value
sctp: Initialize daddr on peeled off socket
net/smc: Fix af_ops of child socket pointing to released memory
net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
net/smc: use memcpy instead of snprintf to avoid out of bounds read
net: macb: Restart tx only if queue pointer is lagging
...
|
|
Scalar properties shouldn't have array constraints (minItems, maxItems,
items). These constraints can simply be dropped with any constraints under
'items' moved up a level.
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Krzysztof Kozlowski <krzk+dt@kernel.org>
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Cc: Yunfei Dong <yunfei.dong@mediatek.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-hwmon@vger.kernel.org
Cc: alsa-devel@alsa-project.org
Cc: linux-iio@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: linux-remoteproc@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20220413140121.3132837-1-robh@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull fscache fixes from David Howells:
"Here's a collection of fscache and cachefiles fixes and misc small
cleanups. The two main fixes are:
- Add a missing unmark of the inode in-use mark in an error path.
- Fix a KASAN slab-out-of-bounds error when setting the xattr on a
cachefiles volume due to the wrong length being given to memcpy().
In addition, there's the removal of an unused parameter, removal of an
unused Kconfig option, conditionalising a bit of procfs-related stuff
and some doc fixes"
* tag 'fscache-fixes-20220413' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
fscache: remove FSCACHE_OLD_API Kconfig option
fscache: Use wrapper fscache_set_cache_state() directly when relinquishing
fscache: Move fscache_cookies_seq_ops specific code under CONFIG_PROC_FS
fscache: Remove the cookie parameter from fscache_clear_page_bits()
docs: filesystems: caching/backend-api.rst: fix an object withdrawn API
docs: filesystems: caching/backend-api.rst: correct two relinquish APIs use
cachefiles: Fix KASAN slab-out-of-bounds in cachefiles_set_volume_xattr
cachefiles: unmark inode in use in error path
|