| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Add pinctrl nodes for the HDMI CEC device to the Exynos4210 and
Exynos4x12 SoCs. These are required by the HDMI CEC device.
Signed-off-by: Kamil Debski <kamil@wypas.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Add new labels to certain nodes so they could be easily referenced by
Exynos4 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
This patch adds a convenient macro which constructs an Exynos pinctrl
pinconf node containing properties needed to configure sleep state of
given pin with given parameters. It will be used by further patch which
adds a large number of sleep states for pins that need such
configuration on certain boards.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The group has the samsung,pin-pud property set to 4, which is not a
correct value. This patch fixes this by replacing it with 3, which is
the correct value for pull-up.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add pinctrl nodes for the ISP I2C0, ISP I2C1 and ISP UART devices.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Add separate nodes for the CAMCLK pin and turn off pull-up on camera
ports A, B. The video bus pins and the clock output (CAMCLK) pin need
separate nodes since full camera port is not used in some configurations,
e.g. for MIPI CSI-2 bus only CAMCLK is required and data/clock signal
use separate dedicated pins.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Keypad pins/lines are board specific and should be added to respective
board dts files.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch corrects the pin function value of sd4_bus8
from 3 to 4. This is verified on origen board for testing
eMMC on dw_mci controller.
Signed-off-by: Shirish S <s.shirish@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch modifies pin control groups of SD pins on EXYNOS4210
and EXYNOS4X12 to use drive strength 3 as a default value which
corresponds to S5P_GPIO_DRVSTR_LV4 in legacy non-DT code.
This is needed at least on Origen board for sdhci2 to work and
if any other drive strength is required on each board, we can
overide it.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: edited commit message]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch adds nodes for pin controllers available on
EXYNOS4X12 SoCs supported by pinctrl-samsung driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
