| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Remove the num-lanes property to avoid the driver setting the
link width.
On FSL Layerscape SoCs, the number of lanes assigned to PCIe
controller is not fixed, it is determined by the selected SerDes
protocol in the RCW (Reset Configuration Word).
The PCIe link training is completed automatically through the selected
SerDes protocol - the link width set-up is updated by hardware after
power on reset, so the num-lanes property is not needed for Layerscape
PCIe.
The current num-lanes property was added erroneously, which actually
indicates the maximum lanes the PCIe controller can support up to,
instead of the lanes assigned to the PCIe controller. The link width set
by SerDes protocol will be overridden by the num-lanes property, hence
the subsequent re-training will fail when the assigned lanes do not
match the value in the num-lanes property.
Remove the property to fix the issue.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
|
|
Pull ARM Device-tree updates from Olof Johansson:
"Besides new bindings and additional descriptions of hardware blocks
for various SoCs and boards, the main new contents here is:
SoCs:
- Intel Agilex (SoCFPGA)
- NXP i.MX8MM (Quad Cortex-A53 with media/graphics focus)
New boards:
- Allwinner:
+ RerVision H3-DVK (H3)
+ Oceanic 5205 5inMFD (H6)
+ Beelink GS2 (H6)
+ Orange Pi 3 (H6)
- Rockchip:
+ Orange Pi RK3399
+ Nanopi NEO4
+ Veyron-Mighty Chromebook variant
- Amlogic:
+ SEI Robotics SEI510
- ST Micro:
+ stm32mp157a discovery1
+ stm32mp157c discovery2
- NXP:
+ Eckelmann ci4x10 (i.MX6DL)
+ i.MX8MM EVK (i.MX8MM)
+ ZII i.MX7 RPU2 (i.MX7)
+ ZII SPB4 (VF610)
+ Zii Ultra (i.MX8M)
+ TQ TQMa7S (i.MX7Solo)
+ TQ TQMa7D (i.MX7Dual)
+ Kobo Aura (i.MX50)
+ Menlosystems M53 (i.MX53)j
- Nvidia:
+ Jetson Nano (Tegra T210)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (593 commits)
arm64: dts: bitmain: Add UART pinctrl support for Sophon Edge
arm64: dts: bitmain: Add pinctrl support for BM1880 SoC
arm64: dts: bitmain: Add GPIO Line names for Sophon Edge board
arm64: dts: bitmain: Add GPIO support for BM1880 SoC
ARM: dts: gemini: Indent DIR-685 partition table
dt-bindings: hwmon (pwm-fan) Remove dead "cooling-*-state" properties
ARM: dts: qcom-apq8064: Set 'cxo_board' as ref clock of the DSI PHY
arm64: dts: msm8998: thermal: Restrict thermal zone name length to under 20
arm64: dts: msm8998: thermal: Fix number of supported sensors
arm64: dts: msm8998-mtp: thermal: Remove skin and battery thermal zones
arm64: dts: exynos: Move fixed-clocks out of soc
arm64: dts: exynos: Move pmu and timer nodes out of soc
ARM: dts: s5pv210: Fix camera clock provider on Goni board
ARM: dts: exynos: Properly override node to use MDMA0 on Universal C210
ARM: dts: exynos: Move fixed-clocks out of soc on Exynos3250
ARM: dts: exynos: Remove unneeded address/size cells from fixed-clock on Exynos3250
ARM: dts: exynos: Move pmu and timer nodes out of soc
arm64: dts: rockchip: fix IO domain voltage setting of APIO5 on rockpro64
arm64: dts: db820c: Add sound card support
arm64: dts: apq8096-db820c: Add HDMI display support
...
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
|
|
Add the 4 Quadrature counters for this board.
Reviewed-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Each eTSEC MAC has its own TBI (SGMII) PCS and private MDIO bus.
But due to a DTS oversight, both SGMII-compatible MACs of the LS1021 SoC
are pointing towards the same internal PCS. Therefore nobody is
controlling the internal PCS of eTSEC0.
Upon initial ndo_open, the SGMII link is ok by virtue of U-boot
initialization. But upon an ifdown/ifup sequence, the code path from
ndo_open -> init_phy -> gfar_configure_serdes does not get executed for
the PCS of eTSEC0 (and is executed twice for MAC eTSEC1). So the SGMII
link remains down for eTSEC0. On the LS1021A-TWR board, to signal this
failure condition, the PHY driver keeps printing
'803x_aneg_done: SGMII link is not ok'.
Also, it changes compatible of mdio0 to "fsl,etsec2-mdio" to match
mdio1 device.
Fixes: 055223d4d22d ("ARM: dts: ls1021a: Enable the eTSEC ports on QDS and TWR")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After switching to the new FSL QSPI driver the properties
'fsl,qspi-has-second-chip' and 'big-endian' are not used anymore.
The driver now uses the 'reg' property to determine the bus and
the chipselect. The endianness is selected by the driver depending
on which SoC is used.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull ARM SoC device tree updates from Arnd Bergmann:
"This is a smaller update than the past few times, but with just over
500 non-merge changesets still dwarfes the rest of the SoC tree.
Three new SoC platforms get added, each one a follow-up to an existing
product, and added here in combination with a reference platform:
- Renesas RZ/A2M (R7S9210) 32-bit Cortex-A9 Real-time imaging
processor:
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rza/rza2m.html
- Renesas RZ/G2E (r8a774c0) 64-bit Cortex-A53 SoC "for Rich Graphics
Applications":
https://www.renesas.com/eu/en/products/microcontrollers-microprocessors/rz/rzg/rzg2e.html
- NXP i.MX8QuadXPlus 64-bit Cortex-A35 SoC:
https://www.nxp.com/products/processors-and-microcontrollers/arm-based-processors-and-mcus/i.mx-applications-processors/i.mx-8-processors/i.mx-8x-family-arm-cortex-a35-3d-graphics-4k-video-dsp-error-correcting-code-on-ddr:i.MX8X
These are actual commercial products we now support with an in-kernel
device tree source file:
- Bosch Guardian is a product made by Bosch Power Tools GmbH, based
on the Texas Instruments AM335x chip
- Winterland IceBoard is a Texas Instruments AM3874 based machine
used in telescopes at the south pole and elsewhere, see commit
d031773169df2 for some pointers:
- Inspur on5263m5 is an x86 server platform with an Aspeed ast2500
baseboard management controller. This is for running on the BMC.
- Zodiac Digital Tapping Unit, apparently a kind of ethernet switch
used in airplanes.
- Phicomm K3 is a WiFi router based on Broadcom bcm47094
- Methode Electronics uDPU FTTdp distribution point unit
- X96 Max, a generic TV box based on Amlogic G12a (S905X2)
- NVIDIA Shield TV (Darcy) based on Tegra210
And then there are several new SBC, evaluation, development or modular
systems that we add:
- Three new Rockchips rk3399 based boards:
- FriendlyElec NanoPC-T4 and NanoPi M4
- Radxa ROCK Pi 4
- Five new i.MX6 family SoM modules and boards for industrial
products:
- Logic PD i.MX6QD SoM and evaluation baseboad
- Y Soft IOTA Draco/Hydra/Ursa family boards based on i.MX6DL
- Phytec phyCORE i.MX6 UltraLite SoM and evaluation module
- MYIR Tech MYD-LPC4357 development based on the NXP lpc4357
microcontroller
- Chameleon96, an Intel/Altera Cyclone5 based FPGA development system
in 96boards form factor
- Arm Fixed Virtual Platforms(FVP) Base RevC, a purely virtual
platform for corresponding to the latest "fast model"
- Another Raspberry Pi variant: Model 3 A+, supported both in 32-bit
and 64-bit mode.
- Oxalis Evalkit V100 based on NXP Layerscape LS1012a, in 96Boards
enterprise form factor
- Elgin RV1108 R1 development board based on 32-bit Rockchips RV1108
For already supported boards and SoCs, we often add support for new
devices after merging the drivers. This time, the largest changes
include updates for
- STMicroelectronics stm32mp1, which was now formally launched last
week
- Qualcomm Snapdragon 845, a high-end phone and low-end laptop chip
- Action Semi S700
- TI AM654x, their recently merged 64-bit SoC from the OMAP family
- Various Amlogic Meson SoCs
- Mediatek MT2712
- NVIDIA Tegra186 and Tegra210
- The ancient NXP lpc32xx family
- Samsung s5pv210, used in some older mobile phones
Many other chips see smaller updates and bugfixes beyond that"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (506 commits)
ARM: dts: exynos: Fix max voltage for buck8 regulator on Odroid XU3/XU4
dt-bindings: net: ti: deprecate cpsw-phy-sel bindings
ARM: dts: am335x: switch to use phy-gmii-sel
ARM: dts: am4372: switch to use phy-gmii-sel
ARM: dts: dm814x: switch to use phy-gmii-sel
ARM: dts: dra7: switch to use phy-gmii-sel
arch: arm: dts: kirkwood-rd88f6281: Remove disabled marvell,dsa reference
ARM: dts: exynos: Add support for secondary DAI to Odroid XU4
ARM: dts: exynos: Add support for secondary DAI to Odroid XU3
ARM: dts: exynos: Disable ARM PMU on Odroid XU3-lite
ARM: dts: exynos: Add stdout path property to Arndale board
ARM: dts: exynos: Add minimal clkout parameters to Exynos3250 PMU
ARM: dts: exynos: Enable ADC on Odroid HC1
arm64: dts: sprd: Remove wildcard compatible string
arm64: dts: sprd: Add SC27XX fuel gauge device
arm64: dts: sprd: Add SC2731 charger device
arm64: dts: sprd: Add ADC calibration support
arm64: dts: sprd: Remove PMIC INTC irq trigger type
arm64: dts: rockchip: Enable tsadc device on rock960
ARM: dts: rockchip: add chosen node on veyron devices
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree changes for 5.1:
- New board support: Logic PD i.MX6QD EVM, ZII SSMB DTU, Phytec
phyBOARD i.MX6UL Segin, Y Soft IOTA Draco, Hydra and Ursa boards.
- Add regulator control for various sensors on imx6qdl-sabresd board.
- Add DISPLAY power domain support for i.MX6SX SoC.
- Add stmpe-adc device node for Toradex iMX6 module.
- Switch to SPDX identifier for imx6q-tbs2910 board.
- Add proper ksz9031 clock skew values for imx6qdl-phytec-pfla02 board.
- Mark I2C recovery GPIOs as open drain and correct and WEIM range
configuration for apalis/colibri boards.
- Small and random updates to various devices.
* tag 'imx-dt-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (31 commits)
ARM: dts: imx: Add support for Logic PD i.MX6QD EVM
ARM: dts: imx6qdl-sabresd: remove reg_sensors' regulator-always-on
ARM: dts: imx6qdl-sabresd: add regulators control for mma8451 sensor
ARM: dts: imx6qdl-sabresd: add regulators control for mag3110 sensor
ARM: dts: imx6qdl-sabresd: add regulator control for isl29023 sensor
ARM: dts: vf610: Add ZII SSMB DTU board
ARM: dts: pfla02: add ksz9031 clock skew values
ARM: dts: imx6qdl-phytec-pfla02: add missing interrupt-controller property
ARM: dts: Add stmpe-adc DT node to Toradex iMX6 modules
ARM: dts: Add devicetree compatibles for LS1021A based boards
ARM: dts: colibri: use valid range configuration for weim
ARM: dts: imx6: Add support for Phytec phyBOARD i.MX6UL Segin
ARM: dts: imx6*-apalis/-colibri: mark I2C recovery GPIOs as open drain
ARM: dts: vf610-zii-ssmb-spu3: Pass "no-sdio"/"no-sd" properties
ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
ARM: dts: imx7ulp: add sim node
ARM: dts: imx6ull: change to use new compatible "fsl,imx6ull-usdhc" for usdhc
ARM: dts: imx6ull: Fix i.MX6ULL/ULZ ocotp compatible
ARM: dts: imx6sx: Add DISPLAY power domain support
ARM: dts: i.MX51: digi-connectcore-som: Add support for I2C bus recovery
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch is to add external trigger stamp fifo support
for 1588 timer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add this property to improve USB read write performance.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add num-viewport property for PCIe DT nodes to specify how many
viewports are implemented.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1021A has a memory controller that supports EDAC. This commit
adds an entry for it.
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
add the qDMA device tree nodes for LS1021A devices.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1021A has 8 possible PWMs, so adding them (disabled by default)
Signed-off-by: Patrick Havelange <patrick.havelange@essensium.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Removed the wrong compatible string "snps,dw-pcie", in case
match incorrect driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the status property disable the PCIe, the property will be enable
by bootloader.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
dtc has new checks for SPI buses. Fix the warnings in node names and
unit-addresses.
There's over 100 warnings for FSL boards, a few examples:
arch/arm/boot/dts/imx28-duckbill-2-spi.dtb: Warning (spi_bus_bridge): /apb@80000000/apbh@80000000/ssp@80014000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx53-ppd.dtb: Warning (spi_bus_bridge): /soc/aips@50000000/spba@50000000/ecspi@50010000: node name for SPI buses should be 'spi'
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dtb: Warning (spi_bus_reg): /soc/aips-bus@2000000/spba-bus@2000000/spi@2014000/mcp251x@1: SPI bus unit address format error, expected "0"
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Li Yang <leoyang.li@nxp.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Gives substantial performance improvement for transfers larger than 16
bytes (DMA_THRESHOLD). Smaller transfers are unaffected.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Pull networking fixes from David Miller:
1) The sockmap code has to free socket memory on close if there is
corked data, from John Fastabend.
2) Tunnel names coming from userspace need to be length validated. From
Eric Dumazet.
3) arp_filter() has to take VRFs properly into account, from Miguel
Fadon Perlines.
4) Fix oops in error path of tcf_bpf_init(), from Davide Caratti.
5) Missing idr_remove() in u32_delete_key(), from Cong Wang.
6) More syzbot stuff. Several use of uninitialized value fixes all
over, from Eric Dumazet.
7) Do not leak kernel memory to userspace in sctp, also from Eric
Dumazet.
8) Discard frames from unused ports in DSA, from Andrew Lunn.
9) Fix DMA mapping and reset/failover problems in ibmvnic, from Thomas
Falcon.
10) Do not access dp83640 PHY registers prematurely after reset, from
Esben Haabendal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
vhost-net: set packet weight of tx polling to 2 * vq size
net: thunderx: rework mac addresses list to u64 array
inetpeer: fix uninit-value in inet_getpeer
dp83640: Ensure against premature access to PHY registers after reset
devlink: convert occ_get op to separate registration
ARM: dts: ls1021a: Specify TBIPA register address
net/fsl_pq_mdio: Allow explicit speficition of TBIPA address
ibmvnic: Do not reset CRQ for Mobility driver resets
ibmvnic: Fix failover case for non-redundant configuration
ibmvnic: Fix reset scheduler error handling
ibmvnic: Zero used TX descriptor counter on reset
ibmvnic: Fix DMA mapping mistakes
tipc: use the right skb in tipc_sk_fill_sock_diag()
sctp: sctp_sockaddr_af must check minimal addr length for AF_INET6
net: dsa: Discard frames from unused ports
sctp: do not leak kernel memory to user space
soreuseport: initialise timewait reuseport field
ipv4: fix uninit-value in ip_route_output_key_hash_rcu()
dccp: initialize ireq->ir_mark
net: fix uninit-value in __hw_addr_add_ex()
...
|
|
The current (mildly evil) fsl_pq_mdio code uses an undocumented shadow of
the TBIPA register on LS1021A, which happens to be read-only.
Changing TBI PHY address therefore does not work on LS1021A.
The real (and documented) address of the TBIPA registere lies in the eTSEC
block and not in MDIO/MII, which is read/write, so using that fixes
the problem.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although the two nodes constitute one contiguous 128K region, still
describe them separately:
- That's how they are described in the reference manual: "Each OCRAM
occupies a 64 KB of address region...", and the names ocram1 and
ocram2 are also as used in the manual.
- The two areas are treated differently by the boot ROM code: OCRAM2 is
zero-initialized, while, again quoting the RM, "software must perform
the zero initialization of OCRAM1."
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
|
|
This avoids the warning
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Esben Haabendal <eha@deif.com>
[RV: adapt commit log to the warning emitted in current mainline]
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add usb2 and usb3 labels to USB2 and USB3 controller device tree nodes,
for easier modification in board dts files.
Signed-off-by: Esben Haabendal <eha@deif.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The LS1021A can be reset via the dcfg regmap in the same way as the
arm64 layerscape SoCs, so add the corresponding DT node.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The timer fixed interval period pulse generator register
is used to generate periodic pulses. The down count
register loads the value programmed in the fixed period
interval (FIPER). At every tick of the timer accumulator
overflow, the counter decrements by the value of
TMR_CTRL[TCLK_PERIOD]. It generates a pulse when the down
counter value reaches zero. It reloads the down counter
in the cycle following a pulse. To use the TMR_FIPER1
register to generate a 1 PPS event, the value
(10^9 nanoseconds) - TCLK_PERIOD should be programmed.
It should be 999999995 not 999999990 since TCLK_PERIOD
is 5.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit a22950c888e3 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add QSPI node support, and this function is disabled by default
This setting could be overwritten in board-level definitions
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the device nodes for flexcan controller(s) present on
LS1021A-Rev2 SoC.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Sakar Arora <Sakar.Arora@freescale.com>
Reviewed-by: Zhengxiong Jin <Jason.Jin@freescale.com>
Reviewed-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In order to maximize the use of MSI, a PCIe controller will share
all MSI controllers. The patch changes msi-parent to refer to all
MSI controller dts nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
"1" should be replaced by "l". This is a typo.
The patch is to fix it.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
qoriq clock driver has been updated to parse the clock configuration
information defined in driver itself not in dts.
Since the new implementation and the bindings have been merged,
it is time to update the clock related node and remove redundent clock
configuration information from the dts.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Also add nodes and properties for thermal management support.
Signed-off-by: Jia Hongtao <hongtao.jia@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The DCU IP has distinct clock inputs for register access and the
pixel clocks, at least in some implementations. LS1021a seems to
use the same clock, therefore specify the same clock for "dcu"
and "pix".
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Both DSPI have signals SPIn_PCS[0:5] so in summary 6 chip-selects, not 5.
Fix that.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add gpio nodes for ls1021a platform dts file. The gpio
IP block of the ls1021a can be supported by the code
drivers/gpio/gpio-mpc8xxx.c.
The compatible "fsl,qoriq-gpio" is used by gpio driver:
drivers/gpio/gpio-mpc8xxx.c to implement general gpio
functionalities.
The chip-specific compatible "fsl,ls1021a-gpio" may be
used to fix potential gpio IP block errata or other
chip-specific gpio issues.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SCFG MSI dts node and add msi-parent property to PCIe dts node
that points to the corresponding MSI node.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Tested-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull more ARM DT changes from Arnd Bergmann:
"Here are some final updates for ARM SoC specific dts files:
- The i.MX changes were sent relatively late, and had a dependency on
the clk tree, so I delayed that a bit. Support for the new i.MX6qp
SoC and a couple of new boards is added in this branch.
- Uniphier renames a few files to match the final product names that
were decided by the company, kudos to the kernel developer(s) for
getting support upstream before the product release. Also two
boards are added. The patches were posted early enough and nice
overall, but we forgot to apply them and decided to give it some
more time in linux-next
- at91 has two small bug fixes"
* tag 'armsoc-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: dts: at91: sama5d4 Xplained: don't disable hsmci regulator
ARM: dts: at91: sama5d3 Xplained: don't disable hsmci regulator
ARM: dts: uniphier: add pinmux node for I2C ch4
ARM: dts: uniphier: add @{address} to EEPROM node
ARM: dts: uniphier: add PH1-Pro4 Sanji board support
ARM: dts: uniphier: add PH1-Pro4 Ace board support
ARM: dts: uniphier: enable I2C channel 2 of ProXstream2 Gentil board
ARM: dts: uniphier: add EEPROM node for ProXstream2 Gentil board
ARM: dts: uniphier: add reference clock nodes
ARM: dts: uniphier: rework UniPhier System Bus nodes
ARM: dts: uniphier: factor out ranges property of support card
arm64: dts: uniphier: rename PH1-LD10 to PH1-LD20
ARM: dts: imx53-qsb: Fix gpio button polarity
ARM: dts: vfxxx: Add DAC node for Vybrid SoC
ARM: dts: imx6q: add missing links between ipu2 and mipi dsi
ARM: dts: imx: Add support for Advantech/GE B850v3
ARM: dts: imx: Add support for Advantech/GE B650v3
ARM: dts: imx: Add support for Advantech/GE B450v3
ARM: dts: imx: Add support for Advantech/GE Bx50v3
ARM: dts: imx: Add Advantech BA-16 Qseven module
...
|
|
LS1021a contains two PCIe controllers. The patch adds their node to
dts file.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add the 1588 timer node for ls1021a platform to
support gianfar ptp driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added sata node to ls1021aqds and ls1021atwr board to support
sata function.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Jianwei Wang <jianwei.wang.chn@gmail.com>
Signed-off-by: Meng Yi <b56799@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add "snps,quirk-frame-length-adjustment" property to
USB3 node for erratum A009116. This property provides
value of GFLADJ_30MHZ for post silicon frame length
adjustment.
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds dma-coherent property for eTSEC nodes, so
coherent DMA operations are supported.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
