Age | Commit message (Collapse) | Author | Files | Lines |
|
When adding the sound support a second instance of the GEN_3V3 regulator was
added by accident. Remove it and point the consumers to the first instance.
Fixes: 663a5b5efa51 ("arm64: dts: zii-ultra: add sound support")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To use the reduced reporting mode the threshold values need to be set
explicitly. Configure the threshold to be less than 0.5% of the full
touchscreen range. This seems to be a good compromise between system
load and input accurancy.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This adds all the necessary nodes to get audio support on both the
RMB3 and Zest boards.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd for example:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Change ZII Ultra board names to be more in line with other ZII RDU platforms.
Signed-off-by: Ruslan Sushko <Ruslan.Sushko@zii.aero>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Zii Ultra design, also known as RDU3, is the i.MX8M based successor
to the the i.MX6 based RDU2. This adds the basic board support for all
components which are supported by the upstream kernel at this time.
The board comes in 2 different versions, called RMB3 and Zest, which
are derived from the same design, but have different layouts and a
few small differences in the populated components.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|