Age | Commit message (Collapse) | Author | Files | Lines |
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
pcmcia: pxa2xx/vpac270: free gpios on exist rather than requesting
ARM: pxa/raumfeld: fix device name for codec ak4104
ARM: pxa/raumfeld: display initialisation fixes
ARM: pxa/raumfeld: adapt to upcoming hardware change
ARM: pxa: fix gpio_to_chip() clash with gpiolib namespace
genirq: replace irq_gc_ack() with {set,clr}_bit variants (fwd)
arm: mach-vt8500: add forgotten irq_data conversion
ARM: pxa168: correct nand pmu setting
ARM: pxa910: correct nand pmu setting
ARM: pxa: fix PGSR register address calculation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into fixes
|
|
In commit f0fba2ad (ASoC: multi-component - ASoC Multi-Component
Support), the name of the ak4104 codec driver was changed without
amending the platform code which uses it as well.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The display requires some milliseconds between GPIO_TFT_VA_EN
and GPIO_DISPLAY_ENABLE. Reorder initialisation to comply with
the display spec.
Also tune timings for better compliance with the spec.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The backlight control is going to change back to PWM in the
upcoming Raumfeld Controller hardware revision.
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The PXA platform code has a static inline helper called
gpio_to_chip which clashes with the gpiolib namespace if we
try to expose the function with the same name from gpiolib,
and it's still confusing even if we don't do that. So rename
it to gpio_to_pxachip().
Reported-by: H Hartley Sweeten <hartleys@visionengravers.com>
Cc: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6994/1: smp_twd: Fix typo in 'twd_timer_rate' printing
ARM: 6987/1: l2x0: fix disabling function to avoid deadlock
ARM: 6966/1: ep93xx: fix inverted RTS/DTR signals on uart1
ARM: 6980/1: mmci: use StartBitErr to detect bad connections
ARM: 6979/1: mach-vt8500: add forgotten irq_data conversion
ARM: move memory layout sanity checking before meminfo initialization
ARM: 6990/1: MAINTAINERS: add entry for ARM PMU profiling and debugging
ARM: 6989/1: perf: do not start the PMU when no events are present
ARM: dmabounce: fix map_single() error return value
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung
* 's5p-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C2440: fix section mismatch on mini2440
ARM: S3C24XX: drop return codes in void function of dma.c
ARM: S3C24XX: don't use uninitialized variable in dma.c
ARM: EXYNOS4: Set appropriate I2C device variant
ARM: S5PC100: Fix for compilation error
spi/s3c64xx: Bug fix for SPI with different FIFO level
ARM: SAMSUNG: Add tx_st_done variable
ARM: EXYNOS4: Address a section mismatch w/ suspend issue.
ARM: S5P: Fix bug on init of PWMTimers for HRTimer
ARM: SAMSUNG: header file revised to prevent declaring duplicated
ARM: EXYNOS4: fix improper gpio configuration
ARM: EXYNOS4: Fix card detection for sdhci 0 and 2
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
omap: drop __initdata tags from static struct platform_device declarations
|
|
If mini2440_init() is in __init, mini2440_parse_features() should also
be in __init. Fixes:
(.text+0x9adc): Section mismatch in reference from the function mini2440_parse_features.clone.0() to the
(unknown reference) .init.data:(unknown)
The function mini2440_parse_features.clone.0() references the (unknown reference) __initdata (unknown).
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Michel Pollet <buserror@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit bb072c3c (ARM / Samsung: Use struct syscore_ops for "core" power
management) turned s3c2410_dma_resume_chan() from int to void. So, drop
the actual return values, too. Fixes:
arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_resume_chan':
arch/arm/plat-s3c24xx/dma.c:1238:3: warning: 'return' with a value, in function returning void
arch/arm/plat-s3c24xx/dma.c:1250:2: warning: 'return' with a value, in function returning void
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Commit 8970ef47 (S3C24XX: Remove hardware specific registers from DMA
calls) removed the parameter dcon in s3c2410_dma_config() and calculates
it on its own. So the debug-output for the old parameter can go, too.
Fixes:
arch/arm/plat-s3c24xx/dma.c: In function 's3c2410_dma_config':
arch/arm/plat-s3c24xx/dma.c:1030:2: warning: 'dcon' is used uninitialized in this function
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This platform has not been converted to 'struct irq_data' when the big
pile was done. It fails to compile nowadays, because the compatibility
code has gone.
CC arch/arm/mach-vt8500/irq.o
arch/arm/mach-vt8500/irq.c:118:2: error: unknown field 'ack' specified in initializer
arch/arm/mach-vt8500/irq.c:118:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:119:2: error: unknown field 'mask' specified in initializer
arch/arm/mach-vt8500/irq.c:119:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:120:2: error: unknown field 'unmask' specified in initializer
arch/arm/mach-vt8500/irq.c:120:2: warning: initialization from incompatible pointer type
arch/arm/mach-vt8500/irq.c:121:2: error: unknown field 'set_type' specified in initializer
arch/arm/mach-vt8500/irq.c:121:2: warning: initialization from incompatible pointer type
make[1]: *** [arch/arm/mach-vt8500/irq.o] Error 1
Add the missing conversion. Tested on a JayPC-Tablet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alexey Charkov <alchark@gmail.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
To get hundredths of MHz the rate needs to be divided by 10'000.
Here is an example:
twd_timer_rate = 123456789
Before the patch:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 1000000) % 100 = 23
Result: 123.23MHz.
After being fixed:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 10000) % 100 = 45
Result: 123.45MHz.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The l2x0_disable function attempts to writel with the l2x0_lock held.
This results in deadlock when the writel contains an outer_sync call
for the platform since the l2x0_lock is already held by the disable
function. A further problem is that disabling the L2 without flushing it
first can lead to the spin_lock operation becoming visible after the
spin_unlock, causing any subsequent L2 maintenance to deadlock.
This patch replaces the writel with a call to writel_relaxed in the
disabling code and adds a flush before disabling in the control
register, preventing livelock from occurring.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It was discovered by Roberto Bergo, that RTS/DTR signals are inverted after
the boot, because it was causing him problems with hardware controlled modem
connected on ttyAM0. Todd Valentic came with this patch for the issue.
Discussion: http://tech.groups.yahoo.com/group/ts-7000/message/20259
Comments from Petr Štetiar:
Sorry, but forget to add Acked-by[1]:
1. https://patchwork.kernel.org/patch/873052/
Cc: Ryan Mallon <ryan@bluewatersys.com>
Cc: Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Todd Valentic <todd.valentic@sri.com>
Tested-by: Roberto Bergo <roberto.bergo@robson.it>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This platform has not been converted to 'struct irq_data' when the big
pile was done and fails to compile nowadays. Tested on a JayPC-Tablet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The original pair of <0x01db, 208000000> is invalid. Correct it to
the valid value.
The 6th bit of the NFC APMU register indicates NFC works whether
at 156Mhz or 78Mhz. So 0x19b indicates NFC works at 156Mhz, and
0x1db indicates it works at 78Mhz.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The original pair of <0x01db, 208000000> is invalid.
Correct to the valid value.
Signed-off-by: Lei Wen <leiwen@marvell.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
The file mfp-pxa2xx.c defines a macro, PGSR(), which translates a gpio
bank number to a PGSR register address. The function pxa2xx_mfp_suspend()
erroneously passed in a gpio number instead of a gpio bank number.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Cc: stable@kernel.org
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
|
|
Set up a correct I2C bus controller variant name for Exynos4.
Without this change the I2C bus driver fails to acquire its
clocks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
|
|
S5PC100 Compilation fails without this patch
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
tx_st_done is required for checking the transmission status of SPI
channels with different fifo levels
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
The section mismatch in headsmp.S made hotplug stop working after the
first instance of suspend-to-RAM and its wakeup.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
This patch fixes following.
<6>[ 0.000000] sched_clock: 32 bits at 33MHz, ...
<6>[ 128.651309] Calibrating delay loop...
There is a big jump. The reason is that PWM Timer which
is for HRTimer was used before its initialization.
So this patch changes its order and following is kernel
boot log message after this.
<6>[ 0.000000] sched_clock: 32 bits at 33MHz, ...
<6>[ 0.000088] Calibrating delay loop...
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
There has been no #ifndef - #define - #endif protection for this
header file.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
These pins are incorrectly configured for PCM2
configure them to SPDIF(_OUT & _EXT_CLK)
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
On SMDKV310 board, a card detect gpio pin is available that is directly
connected to the io pad of the sdhci controller. Fix incorrect value
of cd_type field in platform data for sdhci instance 0 and 2.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
|
|
Ensure that the meminfo array is sanity checked before we pass the
memory to memblock. This helps to ensure that memblock and meminfo
agree on the dimensions of memory, especially when more memory is
passed than the kernel can deal with.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
armpmu_enable can be called in situations where no events are present
(for example, from the event rotation tick after a profiled task has
exited). In this case, we currently start the PMU anyway which may
leave it active inevitably without any events being monitored.
This patch adds a simple check to the enabling code so that we avoid
starting the PMU when no events are present.
Cc: <stable@kernel.org>
Reported-by: Ashwin Chaugle <ashwinc@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc
* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
AT91: Change nand buswidth logic to match hardware default configuration
at91: Use "pclk" as con_id on at91cap9 and at91rm9200
at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
atmel_serial: fix internal port num
at91: fix at91_set_serial_console: use platform device id
|
|
The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Pointers to statically declared platform device structures which are
registered with platform_device_register() are then used during run time
to access these structure members, for example from platform_uevent()
and much more. Therefore, these structures should never be placed inside
sections which are dropped after boot. Fix platform devices incorrectly
tagged with __initdata which happen to exist inside OMAP sub-trees.
This bug has exhibited itself on my ARM/OMAP1 based Amstrad Delta
videophone after commit 6d3163ce86dd386b4f7bda80241d7fea2bc0bb1d, "mm:
check if any page in a pageblock is reserved before marking it
MIGRATE_RESERVE", resulting in reading from several
/sys/device/platform/*/uevent files always ending up with segmentation
faults.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Varadarajan, Charulatha <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
When map_single() is unable to obtain a safe buffer, we must return
the dma_addr_t error value, which is ~0 rather than 0.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x
* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-3.x:
ARM: mach-shmobile: make a struct in board-ap4evb.c static
ARM: mach-shmobile: ag5evm: consistently name sdhi info structures
ARM: mach-shmobile: mackerel: change usbhs devices order
|
|
struct soc_camera_link imx074_link in board-ap4evb.c doesn't have
to be global.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6
* 'tty-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: bcm63xx_uart: fix irq storm after rx fifo overrun.
amba pl011: platform data for reg lockup and glitch v2
amba pl011: workaround for uart registers lockup
tty: n_gsm: improper skb_pull() use was leaking framed data
tty: n_gsm: Fixed logic to decode break signal from modem status
TTY: ntty, add one more sanity check
TTY: ldisc, do not close until there are readers
8250: Fix capabilities when changing the port type
8250_pci: Fix missing const from merges
ARM: SAMSUNG: serial: Fix on handling of one clock source for UART
serial: ioremap warning fix for jsm driver.
8250_pci: add -ENODEV code for Intel EG20T PCH
|
|
* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: pm: ensure ARMv7 CPUs save and restore the TLS register
ARM: pm: proc-v7: fix missing struct processor pointers for suspend code
ARM: 6969/1: plat-iop: fix build error
ARM: 6961/1: zImage: Add build-time check for correctly-sized proc_type entries
ARM: SMP: wait for CPU to be marked active
ARM: 6963/1: Thumb-2: Relax relocation requirements for non-function symbols
ARM: 6962/1: mach-h720x: fix build error
ARM: 6959/1: SMP build fix for entry-macro-multi.S
|
|
Hello,
I am not 100% sure this is the right thing to do, but it makes the
atmel-ssc driver happy on my at91rm9200 board.
This unifies the con_id across all at91 machines.
The atmel-ssc driver expects the con_id to be "pclk" or it will fail probing.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
Ensure that the TLS register is saved and restored over a suspend
cycle, so that userspace programs don't see a corrupted TLS value.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add the missing suspend/resume pointers for the suspend code. This
is needed when building for multiple CPUs.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The iop13xx_defconfig didn't build since the platform code uses
defines from <asm/ptrace.h>. Simply add the include so it
compiles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
It is easy to mis-maintain the proc_types table such that the
entries become wrongly-sized and misaligned when the kernel is
built in Thumb-2.
This patch adds an assembly-time check which will turn most common
size/alignment mistakes in this table into build failures, to avoid
having to debug the boot-time kernel hang which would happen if the
resulting kernel were actually booted.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
When we bring a CPU online, we should wait for it to become active
before entering the idle thread, so we know that the scheduler and
thread migration is going to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Name the SDHI1 instance sh_sdhi1_info to be consistent with sh_sdhi0_info.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
USB1 can use IRQ interrupt and notify function for usbhs driver,
but USB0 is using polling for it.
The priority of usbhs devices order USB1 > USB0 is good idea
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|