summaryrefslogtreecommitdiff
path: root/arch/mips/boot
AgeCommit message (Collapse)AuthorFilesLines
2023-04-08ELF: fix all "Elf" typosAlexey Dobriyan1-1/+1
ELF is acronym and therefore should be spelled in all caps. I left one exception at Documentation/arm/nwfpe/nwfpe.rst which looks like being written in the first person. Link: https://lkml.kernel.org/r/Y/3wGWQviIOkyLJW@p183 Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
2023-03-01mips: dts: ralink: mt7621: add phandle to system controller node for watchdogSergio Paracuellos1-0/+1
To allow to access system controller registers from watchdog driver code add a phandle in the watchdog 'wdt' node. This avoid using arch dependent operations in driver code. Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-03-01mips: dts: ralink: mt7621: rename watchdog node from 'wdt' into 'watchdog'Sergio Paracuellos1-1/+1
Watchdog nodes must use 'watchdog' for node name. When a 'make dtbs_check' is performed the following warning appears: wdt@100: $nodename:0: 'wdt@100' does not match '^watchdog(@.*|-[0-9a-f])?$' Fix this warning up properly renaming the node into 'watchdog'. Reviewed-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-02-19MIPS: DTS: jz4780: add #clock-cells to rtc_devH. Nikolaus Schaller1-0/+2
This makes the driver present the clk32k signal if requested. It is needed to clock the PMU of the BCM4330 WiFi and Bluetooth module of the CI20 board. Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-02-17MIPS: dts: Boston: Fix dtc 'pci_device_reg' warningGenjian Zhang1-1/+1
dtbs_check currently complains that: arch/mips/boot/dts/img/boston.dts:128.19-178.5: Warning (pci_device_reg): /pci@14000000/pci2_root@0,0,0: PCI unit address format error, expected "0,0" The unit-address format should be '<device>,<function>'. Fix the unit-address accordingly. Reported-by: k2ci <kernel-bot@kylinos.cn> Signed-off-by: Genjian Zhang <zhanggenjian@kylinos.cn> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-02-17mips: dts: ralink: mt7621: add port@5 as CPU portArınç ÜNAL3-13/+31
On MT7621AT, MT7621DAT, and MT7621ST SoCs, port 5 of the MT7530 switch is connected to the second MAC of the SoC as a CPU port. Add the port and set up the second MAC on the bindings. Revert PHY muxing on GB-PC1. There's an external PHY connected to the second MAC of the SoC on GB-PC2, therefore, disable port@5 for this device. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-02-17mips: dts: align LED node names with dtschemaArınç ÜNAL11-47/+47
The node names should be generic and DT schema expects certain pattern: mt7621-gnubee-gb-pc1.dtb: gpio-leds: 'power', 'system' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+' Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-02-05MIPS: DTS: CI20: fix otg power gpioH. Nikolaus Schaller1-1/+1
According to schematics it is PF15 and not PF14 (MIC_SW_EN). Seems as if it was hidden and not noticed during testing since there is no sound DT node. Fixes: 158c774d3c64 ("MIPS: Ingenic: Add missing nodes for Ingenic SoCs and boards.") Cc: stable@vger.kernel.org Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2023-02-05MIPS: dts: lantiq: Remove bogus interrupt-parent; lineJonathan Neuschäfer1-1/+0
Specifying interrupt-parent without a value (in other words, as a bool) doesn't really mean anything. Remove one such property in the Lantiq Danube DT, at /sram@1f000000/eiu@101000. Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-12-21MIPS: dts: bcm63268: Add missing properties to the TWD nodeFlorian Fainelli1-0/+2
We currently have a DTC warning with the current DTS due to the lack of a suitable #address-cells and #size-cells property: DTC arch/mips/boot/dts/brcm/bcm63268-comtrend-vr-3032u.dtb arch/mips/boot/dts/brcm/bcm63268.dtsi:115.5-22: Warning (reg_format): /ubus/timer-mfd@10000080/timer@0:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1) arch/mips/boot/dts/brcm/bcm63268.dtsi:120.5-22: Warning (reg_format): /ubus/timer-mfd@10000080/watchdog@1c:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1) arch/mips/boot/dts/brcm/bcm63268.dtsi:111.4-35: Warning (ranges_format): /ubus/timer-mfd@10000080:ranges: "ranges" property has invalid length (12 bytes) (parent #address-cells == 1, child #address-cells == 2, #size-cells == 1) Fixes: d3db4b96ab7f ("mips: dts: bcm63268: add TWD block timer") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-12-08MIPS: mscc: jaguar2: Fix pca9545 i2c-mux node namesGeert Uytterhoeven1-2/+2
"make dtbs_check": arch/mips/boot/dts/mscc/jaguar2_pcb110.dtb: pca9545@70: $nodename:0: 'pca9545@70' does not match '^(i2c-?)?mux' From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml arch/mips/boot/dts/mscc/jaguar2_pcb110.dtb: pca9545@70: Unevaluated properties are not allowed ('#address-cells', '#size-cells', 'i2c@0', 'i2c@1', 'i2c@2', 'i2c@3' were unexpected) From schema: Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.yaml ... Fix this by renaming PCA9545 nodes to "i2c-mux", to match the I2C bus multiplexer/switch DT bindings and the Generic Names Recommendation in the Devicetree Specification. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-12-01mips: dts: remove label = "cpu" from DSA dt-bindingArınç ÜNAL2-2/+0
This is not used by the DSA dt-binding, so remove it from all devicetrees. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-12-01mips: ralink: mt7621: change DSA port labels to generic namingArınç ÜNAL1-5/+5
Change the labels of the DSA ports to generic naming for switch ports. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-12-01mips: ralink: mt7621: fix phy-mode of external phy on GB-PC2Arınç ÜNAL1-1/+1
The phy-mode property must be defined on the MAC instead of the PHY. Define phy-mode under gmac1 which the external phy is connected to. Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-11-21mips: dts: brcm: bcm7435: add "interrupt-names" for NAND controllerRafał Miłecki1-0/+1
Second interrupt can be DMA or EDU one. Specify it explicitly using interrupt-names property. This matches documented binding. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-11-21mips: dts: bcm63268: add TWD block timerRafał Miłecki1-0/+5
BCM63268 TWD contains block with 3 timers. Add binding for it. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-11-21MIPS: DTS: CI20: fix reset line polarity of the ethernet controllerDmitry Torokhov1-1/+1
The reset line is called PWRST#, annotated as "active low" in the binding documentation, and is driven low and then high by the driver to reset the chip. However in device tree for CI20 board it was incorrectly marked as "active high". Fix it. Because (as far as I know) the ci20.dts is always built in the kernel I elected not to also add a quirk to gpiolib to force the polarity there. Fixes: db49ca38579d ("net: davicom: dm9000: switch to using gpiod API") Reported-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-11-11mips: boot/compressed: use __NO_FORTIFYJohn Thomson1-0/+1
In the mips CONFIG_SYS_SUPPORTS_ZBOOT kernel, fix the compile error when using CONFIG_FORTIFY_SOURCE=y LD vmlinuz mipsel-openwrt-linux-musl-ld: arch/mips/boot/compressed/decompress.o: in function `decompress_kernel': ./include/linux/decompress/mm.h:(.text.decompress_kernel+0x177c): undefined reference to `warn_slowpath_fmt' kernel test robot helped identify this as related to fortify. The error appeared with commit 54d9469bc515 ("fortify: Add run-time WARN for cross-field memcpy()") Link: https://lore.kernel.org/r/202209161144.x9xSqNQZ-lkp@intel.com/ Resolve this in the same style as commit cfecea6ead5f ("lib/string: Move helper functions out of string.c") Reported-by: kernel test robot <lkp@intel.com> Fixes: 54d9469bc515 ("fortify: Add run-time WARN for cross-field memcpy()") Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-10-04Merge tag 'net-next-6.1' of ↵Linus Torvalds3-38/+55
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "Core: - Introduce and use a single page frag cache for allocating small skb heads, clawing back the 10-20% performance regression in UDP flood test from previous fixes. - Run packets which already went thru HW coalescing thru SW GRO. This significantly improves TCP segment coalescing and simplifies deployments as different workloads benefit from HW or SW GRO. - Shrink the size of the base zero-copy send structure. - Move TCP init under a new slow / sleepable version of DO_ONCE(). BPF: - Add BPF-specific, any-context-safe memory allocator. - Add helpers/kfuncs for PKCS#7 signature verification from BPF programs. - Define a new map type and related helpers for user space -> kernel communication over a ring buffer (BPF_MAP_TYPE_USER_RINGBUF). - Allow targeting BPF iterators to loop through resources of one task/thread. - Add ability to call selected destructive functions. Expose crash_kexec() to allow BPF to trigger a kernel dump. Use CAP_SYS_BOOT check on the loading process to judge permissions. - Enable BPF to collect custom hierarchical cgroup stats efficiently by integrating with the rstat framework. - Support struct arguments for trampoline based programs. Only structs with size <= 16B and x86 are supported. - Invoke cgroup/connect{4,6} programs for unprivileged ICMP ping sockets (instead of just TCP and UDP sockets). - Add a helper for accessing CLOCK_TAI for time sensitive network related programs. - Support accessing network tunnel metadata's flags. - Make TCP SYN ACK RTO tunable by BPF programs with TCP Fast Open. - Add support for writing to Netfilter's nf_conn:mark. Protocols: - WiFi: more Extremely High Throughput (EHT) and Multi-Link Operation (MLO) work (802.11be, WiFi 7). - vsock: improve support for SO_RCVLOWAT. - SMC: support SO_REUSEPORT. - Netlink: define and document how to use netlink in a "modern" way. Support reporting missing attributes via extended ACK. - IPSec: support collect metadata mode for xfrm interfaces. - TCPv6: send consistent autoflowlabel in SYN_RECV state and RST packets. - TCP: introduce optional per-netns connection hash table to allow better isolation between namespaces (opt-in, at the cost of memory and cache pressure). - MPTCP: support TCP_FASTOPEN_CONNECT. - Add NEXT-C-SID support in Segment Routing (SRv6) End behavior. - Adjust IP_UNICAST_IF sockopt behavior for connected UDP sockets. - Open vSwitch: - Allow specifying ifindex of new interfaces. - Allow conntrack and metering in non-initial user namespace. - TLS: support the Korean ARIA-GCM crypto algorithm. - Remove DECnet support. Driver API: - Allow selecting the conduit interface used by each port in DSA switches, at runtime. - Ethernet Power Sourcing Equipment and Power Device support. - Add tc-taprio support for queueMaxSDU parameter, i.e. setting per traffic class max frame size for time-based packet schedules. - Support PHY rate matching - adapting between differing host-side and link-side speeds. - Introduce QUSGMII PHY mode and 1000BASE-KX interface mode. - Validate OF (device tree) nodes for DSA shared ports; make phylink-related properties mandatory on DSA and CPU ports. Enforcing more uniformity should allow transitioning to phylink. - Require that flash component name used during update matches one of the components for which version is reported by info_get(). - Remove "weight" argument from driver-facing NAPI API as much as possible. It's one of those magic knobs which seemed like a good idea at the time but is too indirect to use in practice. - Support offload of TLS connections with 256 bit keys. New hardware / drivers: - Ethernet: - Microchip KSZ9896 6-port Gigabit Ethernet Switch - Renesas Ethernet AVB (EtherAVB-IF) Gen4 SoCs - Analog Devices ADIN1110 and ADIN2111 industrial single pair Ethernet (10BASE-T1L) MAC+PHY. - Rockchip RV1126 Gigabit Ethernet (a version of stmmac IP). - Ethernet SFPs / modules: - RollBall / Hilink / Turris 10G copper SFPs - HALNy GPON module - WiFi: - CYW43439 SDIO chipset (brcmfmac) - CYW89459 PCIe chipset (brcmfmac) - BCM4378 on Apple platforms (brcmfmac) Drivers: - CAN: - gs_usb: HW timestamp support - Ethernet PHYs: - lan8814: cable diagnostics - Ethernet NICs: - Intel (100G): - implement control of FCS/CRC stripping - port splitting via devlink - L2TPv3 filtering offload - nVidia/Mellanox: - tunnel offload for sub-functions - MACSec offload, w/ Extended packet number and replay window offload - significantly restructure, and optimize the AF_XDP support, align the behavior with other vendors - Huawei: - configuring DSCP map for traffic class selection - querying standard FEC statistics - querying SerDes lane number via ethtool - Marvell/Cavium: - egress priority flow control - MACSec offload - AMD/SolarFlare: - PTP over IPv6 and raw Ethernet - small / embedded: - ax88772: convert to phylink (to support SFP cages) - altera: tse: convert to phylink - ftgmac100: support fixed link - enetc: standard Ethtool counters - macb: ZynqMP SGMII dynamic configuration support - tsnep: support multi-queue and use page pool - lan743x: Rx IP & TCP checksum offload - igc: add xdp frags support to ndo_xdp_xmit - Ethernet high-speed switches: - Marvell (prestera): - support SPAN port features (traffic mirroring) - nexthop object offloading - Microchip (sparx5): - multicast forwarding offload - QoS queuing offload (tc-mqprio, tc-tbf, tc-ets) - Ethernet embedded switches: - Marvell (mv88e6xxx): - support RGMII cmode - NXP (felix): - standardized ethtool counters - Microchip (lan966x): - QoS queuing offload (tc-mqprio, tc-tbf, tc-cbs, tc-ets) - traffic policing and mirroring - link aggregation / bonding offload - QUSGMII PHY mode support - Qualcomm 802.11ax WiFi (ath11k): - cold boot calibration support on WCN6750 - support to connect to a non-transmit MBSSID AP profile - enable remain-on-channel support on WCN6750 - Wake-on-WLAN support for WCN6750 - support to provide transmit power from firmware via nl80211 - support to get power save duration for each client - spectral scan support for 160 MHz - MediaTek WiFi (mt76): - WiFi-to-Ethernet bridging offload for MT7986 chips - RealTek WiFi (rtw89): - P2P support" * tag 'net-next-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1864 commits) eth: pse: add missing static inlines once: rename _SLOW to _SLEEPABLE net: pse-pd: add regulator based PSE driver dt-bindings: net: pse-dt: add bindings for regulator based PoDL PSE controller ethtool: add interface to interact with Ethernet Power Equipment net: mdiobus: search for PSE nodes by parsing PHY nodes. net: mdiobus: fwnode_mdiobus_register_phy() rework error handling net: add framework to support Ethernet PSE and PDs devices dt-bindings: net: phy: add PoDL PSE property net: marvell: prestera: Propagate nh state from hw to kernel net: marvell: prestera: Add neighbour cache accounting net: marvell: prestera: add stub handler neighbour events net: marvell: prestera: Add heplers to interact with fib_notifier_info net: marvell: prestera: Add length macros for prestera_ip_addr net: marvell: prestera: add delayed wq and flush wq on deinit net: marvell: prestera: Add strict cleanup of fib arbiter net: marvell: prestera: Add cleanup of allocated fib_nodes net: marvell: prestera: Add router nexthops ABI eth: octeon: fix build after netif_napi_add() changes net/mlx5: E-Switch, Return EBUSY if can't get mode lock ...
2022-09-23mips: dts: ralink: mt7621: add GB-PC2 LEDsArınç ÜNAL2-12/+36
Add the missing LEDs for GB-PC2. The ethblack-green, ethblue-green, power and system LEDs weren't added previously, because they don't exist on the device schematics. Tests on a GB-PC2 by me and Petr proved otherwise. The i2c bus cannot be used on GB-PC2 as its pins are wired to LEDs instead, and GB-PC1 does not use it. Therefore, do not enable it on both devices. Link: https://github.com/ngiger/GnuBee_Docs/blob/master/GB-PCx/Documents/GB-PC2_V1.1_schematic.pdf Tested-by: Petr Louda <petr.louda@outlook.cz> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-23mips: dts: ralink: mt7621: fix external phy on GB-PC2Arınç ÜNAL1-3/+3
The address of the external phy on the mdio bus is 5. Update the devicetree for GB-PC2 accordingly. Fixes: 5bc148649cf3 ("staging: mt7621-dts: fix GB-PC2 devicetree") Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-23mips: dts: ralink: mt7621: change mt7530 switch addressArınç ÜNAL1-2/+2
In the case of muxing phy0 of the MT7530 switch, the switch and the phy will have the same address on the mdio bus, 0. This causes the ethernet driver to fail since devices on the mdio bus cannot share an address. Any address can be used for the switch, therefore, change the switch address to 0x1f. Suggested-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-23mips: dts: ralink: mt7621: change phy-mode of gmac1 to rgmiiArınç ÜNAL1-1/+1
Change phy-mode of gmac1 to rgmii on mt7621.dtsi. Same code path is followed for delayed rgmii and rgmii phy-mode on mtk_eth_soc.c. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-23mips: dts: ralink: mt7621: remove interrupt-parent from switch nodeArınç ÜNAL1-1/+0
The interrupt-parent property is inherited from the ethernet node as it's a parent node of the switch node. Therefore, remove the unnecessary interrupt-parent property from the switch node. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-23mips: dts: ralink: mt7621: fix some dtc warningsArınç ÜNAL3-20/+14
Fix the dtc warnings below. uartlite@c00: $nodename:0: 'uartlite@c00' does not match '^serial(@.*)?$' From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml uartlite@c00: Unevaluated properties are not allowed ('clock-names' was unexpected) From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/serial/8250.yaml sdhci@1e130000: $nodename:0: 'sdhci@1e130000' does not match '^mmc(@.*)?$' From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/mmc/mtk-sd.yaml xhci@1e1c0000: $nodename:0: 'xhci@1e1c0000' does not match '^usb(@.*)?' From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml xhci@1e1c0000: compatible: ['mediatek,mt8173-xhci'] is too short From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.yaml switch0@0: $nodename:0: 'switch0@0' does not match '^(ethernet-)?switch(@.*)?$' From schema: /home/arinc9/Documents/linux/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml port@1: status:0: 'off' is not one of ['okay', 'disabled', 'reserved'] From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml port@2: status:0: 'off' is not one of ['okay', 'disabled', 'reserved'] From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml port@3: status:0: 'off' is not one of ['okay', 'disabled', 'reserved'] From schema: /home/arinc9/.local/lib/python3.10/site-packages/dtschema/schemas/dt-core.yaml - Change "memc: syscon@5000" to "memc: memory-controller@5000". - Change "uartlite: uartlite@c00" to "serial0: serial@c00" and remove the aliases node. - Remove "clock-names" from the serial0 node. The property doesn't exist on the 8250.yaml schema. - Change "sdhci: sdhci@1e130000" to "mmc: mmc@1e130000". - Change "xhci: xhci@1e1c0000" to "usb: usb@1e1c0000". - Add "mediatek,mtk-xhci" as the second compatible string on the usb node. - Change "switch0: switch0@0" to "switch0: switch@0" - Change "off" to "disabled" for disabled nodes. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-19mips: bmips: bcm63268: add TWD block bindingRafał Miłecki1-6/+12
TWD is an MFD block that contains timers, watchdog & some clocks / reset controller. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-09-12MIPS: dts: lantiq: rename dts files with soc name being the prefixAleksander Jan Bajkowski2-1/+1
Rename lantiq dts files with soc name being the prefix, so that the board dts file can be located easily by soc name, and we also gain the consistency of naming. This patch is a preparation for the addition of dts for newer SoCs (Lantiq ARX100, VRX200 and xRX330). Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-07-14MIPS: dts: align gpio-key node names with dtschemaKrzysztof Kozlowski4-4/+4
The node names should be generic and DT schema expects certain pattern (e.g. with key/button/switch). Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-07-14MIPS: dts: correct gpio-keys names and propertiesKrzysztof Kozlowski10-57/+37
gpio-keys children do not use unit addresses. Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-07-05MIPS: mscc: ocelot: enable FDMA usageAlexandre Belloni1-4/+5
Enable FDMA usage by adding "fdma" resource in regs and interrupts. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Clément Léger <clement.leger@bootlin.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-06-21mips: dts: ingenic: Add TCU clock to x1000/x1830 tcu device nodeAidan MacDonald2-4/+6
This clock is a gate for the TCU hardware block on these SoCs, but it wasn't included in the device tree since the ingenic-tcu driver erroneously did not request it. Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-06-03Merge tag 'usb-5.19-rc1' of ↵Linus Torvalds3-3/+3
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb Pull USB / Thunderbolt updates from Greg KH: "Here is the "big" set of USB and Thunderbolt driver changes for 5.18-rc1. For the most part it's been a quiet development cycle for the USB core, but there are the usual "hot spots" of development activity. Included in here are: - Thunderbolt driver updates: - fixes for devices without displayport adapters - lane bonding support and improvements - other minor changes based on device testing - dwc3 gadget driver changes. It seems this driver will never be finished given that the IP core is showing up in zillions of new devices and each implementation decides to do something different with it... - uvc gadget driver updates as more devices start to use and rely on this hardware as well - usb_maxpacket() api changes to remove an unneeded and unused parameter. - usb-serial driver device id updates and small cleanups - typec cleanups and fixes based on device testing - device tree updates for usb properties - lots of other small fixes and driver updates. All of these have been in linux-next for weeks with no reported problems" * tag 'usb-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (154 commits) USB: new quirk for Dell Gen 2 devices usb: dwc3: core: Add error log when core soft reset failed usb: dwc3: gadget: Move null pinter check to proper place usb: hub: Simplify error and success path in port_over_current_notify usb: cdns3: allocate TX FIFO size according to composite EP number usb: dwc3: Fix ep0 handling when getting reset while doing control transfer usb: Probe EHCI, OHCI controllers asynchronously usb: isp1760: Fix out-of-bounds array access xhci: Don't defer primary roothub registration if there is only one roothub USB: serial: option: add Quectel BG95 modem USB: serial: pl2303: fix type detection for odd device xhci: Allow host runtime PM as default for Intel Alder Lake N xHCI xhci: Remove quirk for over 10 year old evaluation hardware xhci: prevent U2 link power state if Intel tier policy prevented U1 xhci: use generic command timer for stop endpoint commands. usb: host: xhci-plat: omit shared hcd if either root hub has no ports usb: host: xhci-plat: prepare operation w/o shared hcd usb: host: xhci-plat: create shared hcd after having added main hcd xhci: prepare for operation w/o shared hcd xhci: factor out parts of xhci_gen_setup() ...
2022-05-30Merge tag 'mips_5.19' of ↵Linus Torvalds18-145/+211
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS updates from Thomas Bogendoerfer: "Cleanups and fixes" * tag 'mips_5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (38 commits) MIPS: RALINK: Define pci_remap_iospace under CONFIG_PCI_DRIVERS_GENERIC MIPS: Use memblock_add_node() in early_parse_mem() under CONFIG_NUMA MIPS: Return -EINVAL if mem parameter is empty in early_parse_mem() MIPS: Kconfig: Fix indentation and add endif comment MIPS: bmips: Fix compiler warning observed on W=1 build MIPS: Rewrite `csum_tcpudp_nofold' in plain C mips: setup: use strscpy to replace strlcpy MIPS: Octeon: add SNIC10E board MIPS: Ingenic: Refresh defconfig for CU1000-Neo and CU1830-Neo. MIPS: Ingenic: Refresh device tree for Ingenic SoCs and boards. MIPS: Ingenic: Add PWM nodes for X1830. MIPS: Octeon: fix typo in comment MIPS: loongson32: Kconfig: Remove extra space MIPS: Sibyte: remove unnecessary return variable MIPS: Use NOKPROBE_SYMBOL() instead of __kprobes annotation selftests/ftrace: Save kprobe_events to test log MIPS: tools: no need to initialise statics to 0 MIPS: Loongson: Use hwmon_device_register_with_groups() to register hwmon MIPS: VR41xx: Drop redundant spinlock initialization MIPS: smp: optimization for flush_tlb_mm when exiting ...
2022-05-23MIPS: Ingenic: Refresh device tree for Ingenic SoCs and boards.周琰杰 (Zhou Yanjie)4-74/+138
1.Add SSI nodes for X1000 SoC and X1830 SoC from Ingenic. 2.Refresh SSI related nodes in CU1000-Neo and CU1830-Neo. 3.The X1830 SoC used by the CU1830-Neo and the X1000 SoC used by the CU1000-Neo are both single-core processors, therefore the "OST_CLK_PERCPU_TIMER" ABI should not be used in the OST nodes of the CU1830-Neo and CU1000-Neo, it is just a coincidence that there is no problem now. So replace the misused "OST_CLK_PERCPU_TIMER" ABI with the correct "OST_CLK_EVENT_TIMER" ABI. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-05-23MIPS: Ingenic: Add PWM nodes for X1830.周琰杰 (Zhou Yanjie)1-0/+14
Add PWM node for X1830 SoC from Ingenic. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-05-12MIPS: tools: no need to initialise statics to 0Jason Wang1-1/+1
Static variables do not need to be initialised to 0, because compiler will initialise all uninitialised statics to 0. Thus, remove the unneeded initializations. Signed-off-by: Jason Wang <wangborong@cdjrlc.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27mips: dts: ingenic: x1000: Add PWM device tree nodeAidan MacDonald1-0/+12
Copied from the jz4740 devicetree and trimmed to 5 timers, which is what the hardware supports. Signed-off-by: Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27MIPS: mscc: serval: rename pinctrl nodesMichael Walle1-7/+7
The pinctrl device tree binding will be converted to YAML format. Rename the pin nodes so they end with "-pins" to match the schema. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27MIPS: mscc: ocelot: rename pinctrl nodesMichael Walle2-5/+5
The pinctrl device tree binding will be converted to YAML format. Rename the pin nodes so they end with "-pins" to match the schema. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27MIPS: mscc: jaguar2: rename pinctrl nodesMichael Walle3-13/+13
The pinctrl device tree binding will be converted to YAML format. Rename the pin nodes so they end with "-pins" to match the schema. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27mips: dts: ralink: mt7621: remove defining gpio function for pin groupsArınç ÜNAL2-24/+0
All pin groups function as gpio unless set otherwise. Therefore, remove this unnecessary binding. Tested on UniElec U7621-06-16M on OpenWrt. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27mips: dts: ralink: mt7621: mux phy4 to gmac1 for GB-PC1Arınç ÜNAL1-8/+10
Mux the MT7530 switch's phy4 to the SoC's gmac1 on the GB-PC1 devicetree. This achieves 2 Gbps total bandwidth to the CPU using the second RGMII. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-27mips: dts: ralink: mt7621: add mdio label to mdio-busArınç ÜNAL2-11/+9
Add mdio label to the mdio-bus node to easily refer to it. Use the newly created label on the GB-PC2 devicetree. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-26MIPS: dts: align SPI NOR node name with dtschemaKrzysztof Kozlowski6-6/+6
The node names should be generic and SPI NOR dtschema expects "flash". Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-04-23mips: dts: ralink: mt7621: use the new compatible string for MT7621 pinctrlArınç ÜNAL1-1/+1
Use the new compatible string "ralink,mt7621-pinctrl" for the Ralink MT7621 pinctrl subdriver on mt7621.dtsi. Each subdriver needs to have a different compatible string. We don't want the same compatible string to match a different subdriver's pinmux data as it's not for our SoC. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Link: https://lore.kernel.org/r/20220414173916.5552-10-arinc.unal@arinc9.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-04-21MIPS: Ingenic: Refresh USB nodes to match driver changes.周琰杰 (Zhou Yanjie)3-3/+3
Refresh USB nodes in the jz4780.dtsi, x1000.dtsi, and x1830.dtsi files. Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com> Link: https://lore.kernel.org/r/1649964337-114337-4-git-send-email-zhouyanjie@wanyeetech.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-28Merge tag 'staging-5.18-rc1' of ↵Linus Torvalds4-0/+751
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging Pull staging driver updates from Greg KH: "Here is the big set of staging driver updates for 5.18-rc1. Loads of tiny cleanups for almost all staging drivers in here, nothing major at all. Highlights include: - remove the ashmem Android driver. It is long-dead and if there are any legacy userspace applications still using it, the Android kernel images will maintain it, the community shouldn't care about it anymore - wfx wifi driver major cleanups. Should be ready to merge out of staging soon, and will coordinate with the wifi maintainers after -rc1 is out - major cleanups and unwinding of the layers of the r8188eu driver. It's amazing just how many unneeded layers of abstraction is in there, just when we think it's done, another is found... - lots of tiny coding style cleanups in many other staging drivers. All have been in linux-next for a while with no reported problems" * tag 'staging-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (455 commits) staging: r8188eu: remove unnecessary memset in r8188eu staging: greybus: introduce pwm_ops::apply staging: rts5208: Resolve checkpatch.pl issues. staging: sm750fb: fix naming style staging: fbtft: Consider type of init sequence values in fbtft_init_display() staging: fbtft: Constify buf parameter in fbtft_dbg_hex() staging: mmal-vchiq: clear redundant item named bulk_scratch mips: dts: ralink: add MT7621 SoC staging: r8188eu: remove some unused local ieee80211 macros staging: r8188eu: make rtl8188e_process_phy_info static staging: r8188eu: remove unused function prototype staging: r8188eu: remove three unused receive defines staging: r8188eu: remove unnecessary initializations staging: rtl8192e: Fix spelling mistake "RESQUEST" -> "REQUEST" MAINTAINERS: remove the obsolete file entry for staging in ANDROID DRIVERS staging: r8188eu: proper error handling in rtw_init_drv_sw staging: r8188eu: call _cancel_timer_ex from _rtw_free_recv_priv staging: vt6656: Removed unused variable vt3342_vnt_threshold staging: vt6656: Removed unused variable bb_vga_0 staging: remove ashmem ...
2022-03-25Merge tag 'mips_5.18' of ↵Linus Torvalds3-6/+7
git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux Pull MIPS updates from Thomas Bogendoerfer: - added support for QCN550x (ath79) - enabled KCSAN - removed TX39XX support - various cleanups and fixes * tag 'mips_5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (31 commits) MIPS: Fix build error for loongson64 and sgi-ip27 MIPS: ingenic: correct unit node address MIPS: Fix wrong comments in asm/prom.h MIPS: Remove redundant definitions of device_tree_init() MIPS: Remove redundant check in device_tree_init() MIPS: pgalloc: fix memory leak caused by pgd_free() MIPS: RB532: fix return value of __setup handler MIPS: Only use current_stack_pointer on GCC MIPS: boot/compressed: Use array reference for image bounds mips: cdmm: Fix refcount leak in mips_cdmm_phys_base mips: remove reference to "newer Loongson-3" mips: Always permit to build u-boot images MIPS: Sanitise Cavium switch cases in TLB handler synthesizers DEC: Limit PMAX memory probing to R3k systems mips: DEC: honor CONFIG_MIPS_FP_SUPPORT=n MIPS: fix fortify panic when copying asm exception handlers mips: ralink: fix a refcount leak in ill_acc_of_setup() mips: Implement "current_stack_pointer" MIPS: Remove TX39XX support MIPS: Modernize READ_IMPLIES_EXEC ...
2022-03-18MIPS: ingenic: correct unit node addressKrzysztof Kozlowski1-1/+1
Unit node addresses should not have leading 0x: Warning (unit_address_format): /nemc@13410000/efuse@d0/eth-mac-addr@0x22: unit name should not have leading "0x" Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Reviewed-by: Paul Cercueil <paul@crapouillou.net> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2022-03-16mips: dts: ralink: add MT7621 SoCArınç ÜNAL4-0/+751
The MT7621 system-on-a-chip includes an 880 MHz MIPS1004Kc dual-core CPU, a 5-port 10/100/1000 switch/PHY and one RGMII. Add the devicetrees for GB-PC1 and GB-PC2 devices which use MT7621 SoC. Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com> Acked-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> Link: https://lore.kernel.org/r/20220315160149.3617-1-arinc.unal@arinc9.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
generated by cgit v1.2.3 (git 2.39.0) at 2024-08-04 05:52:17 +0300