Age | Commit message (Collapse) | Author | Files | Lines |
|
Fix typos, most reported by "codespell arch/x86". Only touches comments,
no code changes.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20240103004011.1758650-1-helgaas@kernel.org
|
|
IOSF MBI header contains a lot of definitions, such as
end point addresses of IPs. Move CCK address from AtomISP driver
to generic header.
While here, drop unused one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
On some BYT/CHT systems the SoC's P-Unit shares the I2C bus with the
kernel. The P-Unit has a semaphore for the PMIC bus which we can take to
block it from accessing the shared bus while the kernel wants to access it.
Currently we have the I2C-controller driver acquiring and releasing the
semaphore around each I2C transfer. There are 2 problems with this:
1) PMIC accesses often come in the form of a read-modify-write on one of
the PMIC registers, we currently release the P-Unit's PMIC bus semaphore
between the read and the write. If the P-Unit modifies the register during
this window?, then we end up overwriting the P-Unit's changes.
I believe that this is mostly an academic problem, but I'm not sure.
2) To safely access the shared I2C bus, we need to do 3 things:
a) Notify the GPU driver that we are starting a window in which it may not
access the P-Unit, since the P-Unit seems to ignore the semaphore for
explicit power-level requests made by the GPU driver
b) Make a pm_qos request to force all CPU cores out of C6/C7 since entering
C6/C7 while we hold the semaphore hangs the SoC
c) Finally take the P-Unit's PMIC bus semaphore
All 3 these steps together are somewhat expensive, so ideally if we have
a bunch of i2c transfers grouped together we only do this once for the
entire group.
Taking the read-modify-write on a PMIC register as example then ideally we
would only do all 3 steps once at the beginning and undo all 3 steps once
at the end.
For this we need to be able to take the semaphore from within e.g. the PMIC
opregion driver, yet we do not want to remove the taking of the semaphore
from the I2C-controller driver, as that is still necessary to protect many
other code-paths leading to accessing the shared I2C bus.
This means that we first have the PMIC driver acquire the semaphore and
then have the I2C controller driver trying to acquire it again.
To make this possible this commit does the following:
1) Move the semaphore code from being private to the I2C controller driver
into the generic iosf_mbi code, which already has other code to deal with
the shared bus so that it can be accessed outside of the I2C bus driver.
2) Rework the code so that it can be called multiple times nested, while
still blocking I2C accesses while e.g. the GPU driver has indicated the
P-Unit needs the bus through a iosf_mbi_punit_acquire() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
More change sets for 4.16:
- Many improvements for selftests and other igt tests (Chris)
- Forcewake with PUNIT->PMIC bus fixes and robustness (Hans)
- Define an engine class for uABI (Tvrtko)
- Context switch fixes and improvements (Chris)
- GT powersavings and power gating simplification and fixes (Chris)
- Other general driver clean-ups (Chris, Lucas, Ville)
- Removing old, useless and/or bad workarounds (Chris, Oscar, Radhakrishna)
- IPS, pipe config, etc in preparation for another Fast Boot attempt (Maarten)
- OA perf fixes and support to Coffee Lake and Cannonlake (Lionel)
- Fixes around GPU fault registers (Michel)
- GEM Proxy (Tina)
- Refactor of Geminilake and Cannonlake plane color handling (James)
- Generalize transcoder loop (Mika Kahola)
- New HW Workaround for Cannonlake and Geminilake (Rodrigo)
- Resume GuC before using GEM (Chris)
- Stolen Memory handling improvements (Ville)
- Initialize entry in PPAT for older compilers (Chris)
- Other fixes and robustness improvements on execbuf (Chris)
- Improve logs of GEM_BUG_ON (Mika Kuoppala)
- Rework with massive rename of GuC functions and files (Sagar)
- Don't sanitize frame start delay if pipe is off (Ville)
- Cannonlake clock fixes (Rodrigo)
- Cannonlake HDMI 2.0 support (Rodrigo)
- Add a GuC doorbells selftest (Michel)
- Add might_sleep() check to our wait_for() (Chris)
Many GVT changes for 4.16:
- CSB HWSP update support (Weinan)
- GVT debug helpers, dyndbg and debugfs (Chuanxiao, Shuo)
- full virtualized opregion (Xiaolin)
- VM health check for sane fallback (Fred)
- workload submission code refactor for future enabling (Zhi)
- Updated repo URL in MAINTAINERS (Zhenyu)
- other many misc fixes
* tag 'drm-intel-next-2017-11-17-1' of git://anongit.freedesktop.org/drm/drm-intel: (260 commits)
drm/i915: Update DRIVER_DATE to 20171117
drm/i915: Add a policy note for removing workarounds
drm/i915/selftests: Report ENOMEM clearly for an allocation failure
Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
drm/i915: Calculate g4x intermediate watermarks correctly
drm/i915: Calculate vlv/chv intermediate watermarks correctly, v3.
drm/i915: Pass crtc_state to ips toggle functions, v2
drm/i915: Pass idle crtc_state to intel_dp_sink_crc
drm/i915: Enable FIFO underrun reporting after initial fastset, v4.
drm/i915: Mark the userptr invalidate workqueue as WQ_MEM_RECLAIM
drm/i915: Add might_sleep() check to wait_for()
drm/i915/selftests: Add a GuC doorbells selftest
drm/i915/cnl: Extend HDMI 2.0 support to CNL.
drm/i915/cnl: Simplify dco_fraction calculation.
drm/i915/cnl: Don't blindly replace qdiv.
drm/i915/cnl: Fix wrpll math for higher freqs.
drm/i915/cnl: Fix, simplify and unify wrpll variable sizes.
drm/i915/cnl: Remove useless conversion.
drm/i915/cnl: Remove spurious central_freq.
drm/i915/selftests: exercise_ggtt may have nothing to do
...
|
|
For race free unregistration drivers may need to acquire PMIC bus access
through iosf_mbi_punit_acquire() and then (un)register the notifier without
dropping the lock.
This commit adds an unlocked variant of
iosf_mbi_unregister_pmic_bus_access_notifier for this use case.
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019111620.26761-2-hdegoede@redhat.com
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some drivers may need to acquire P-Unit managed resources from interrupt
context, where they cannot call iosf_mbi_punit_acquire().
This commit adds a notifier chain which allows a driver to get notified
(in a process context) before other drivers start accessing the PMIC bus,
so that the driver can acquire any resources, which it may need during
the window the other driver is accessing the PMIC, before hand.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=155241
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: tagorereddy <tagore.chandan@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
One some systems the P-Unit accesses the PMIC to change various voltages
through the same bus as other kernel drivers use for e.g. battery
monitoring.
If a driver sends requests to the P-Unit which require the P-Unit to access
the PMIC bus while another driver is also accessing the PMIC bus various
bad things happen.
This commit adds a mutex to protect the P-Unit against simultaneous
accesses and 2 functions to lock / unlock this mutex.
Note on these systems the i2c-bus driver will request a sempahore from the
P-Unit for exclusive access to the PMIC bus when i2c drivers are accessing
it, but this does not appear to be sufficient, we still need to avoid
making certain P-Unit requests during the access window to avoid problems.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=155241
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: tagorereddy <tagore.chandan@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20170210102802.20898-2-hdegoede@redhat.com
|
|
This is a third approach to workaround long standing issue with LPSS on
BayTrail. First one [1] was reverted since it didn't resolve the issue
comprehensively. Second one [2] was rejected by internal review.
The LPSS DMA controller does not have neither _PS0 nor _PS3 method. Moreover it
can be powered off automatically whenever the last LPSS device goes down. In
case of no power any access to the DMA controller will hang the system. The
behaviour is reproduced on some HP laptops based on Intel BayTrail [3,4] as
well as on ASuS T100TA transformer.
Power on the LPSS island through the registers accessible in a specific way.
[1] http://www.spinics.net/lists/linux-acpi/msg53963.html
[2] https://bugzilla.redhat.com/attachment.cgi?id=1066779&action=diff
[3] https://bugzilla.redhat.com/show_bug.cgi?id=1184273
[4] http://www.spinics.net/lists/dmaengine/msg01514.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The read and write opcodes are global for all units on SoC and even across
Intel SoCs. Remove duplication of corresponding constants. At the same time
convert all current users.
No functional change.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Boon Leong Ong <boon.leong.ong@intel.com>
Acked-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
- Move the static variables to one place
- Fix indentations in the header
- Correct comments
No functional change.
[ tglx: Massaged changelog ]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: David E . Box <david.e.box@linux.intel.com>
Link: http://lkml.kernel.org/r/1436366709-17683-5-git-send-email-andriy.shevchenko@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Added all the MBI units below and their associated read/write
opcodes:
- Host Bridge Arbiter
- Host Bridge
- Remote Management Unit
- Memory Manager & eSRAM
- SoC Unit
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Link: http://lkml.kernel.org/r/1399668248-24199-3-git-send-email-david.e.box@linux.intel.com
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Currently drivers that run on non-IOSF systems (Core/Xeon) can't use the IOSF
driver on SOC's without selecting it which forces an unnecessary and limiting
dependency. Provides dummy functions to allow these modules to conditionally
use the driver on IOSF equipped platforms without impacting their ability to
compile and load on non-IOSF platforms. Build default m to ensure availability
on x86 SOC's.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: http://lkml.kernel.org/r/1399668248-24199-2-git-send-email-david.e.box@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Current Intel SOC cores use a MailBox Interface (MBI) to provide access to
configuration registers on devices (called units) connected to the system
fabric. This is a support driver that implements access to this interface on
those platforms that can enumerate the device using PCI. Initial support is for
BayTrail, for which port definitons are provided. This is a requirement for
implementing platform specific features (e.g. RAPL driver requires this to
perform platform specific power management using the registers in PUNIT).
Dependant modules should select IOSF_MBI in their respective Kconfig
configuraiton. Serialized access is handled by all exported routines with
spinlocks.
The API includes 3 functions for access to unit registers:
int iosf_mbi_read(u8 port, u8 opcode, u32 offset, u32 *mdr)
int iosf_mbi_write(u8 port, u8 opcode, u32 offset, u32 mdr)
int iosf_mbi_modify(u8 port, u8 opcode, u32 offset, u32 mdr, u32 mask)
port: indicating the unit being accessed
opcode: the read or write port specific opcode
offset: the register offset within the port
mdr: the register data to be read, written, or modified
mask: bit locations in mdr to change
Returns nonzero on error
Note: GPU code handles access to the GFX unit. Therefore access to that unit
with this driver is disallowed to avoid conflicts.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Link: http://lkml.kernel.org/r/1389216471-734-1-git-send-email-david.e.box@linux.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
|