| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This patch seperates inline ipsec functionality from coprocessor
driver chcr. Now inline ipsec is separate ULD, moved from
"drivers/crypto/chelsio/" to "drivers/net/ethernet/chelsio/inline_crypto/ch_ipsec/"
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
|
|
This patch fixes the compilation warnings displayed by sparse tool for
chcr driver.
V1->V2
Avoid type casting by using get_unaligned_be32() and
put_unaligned_be16/32() functions.
The key which comes from stack is an u8 byte stream so we store it in
an unsigned char array(ablkctx->key). The function get_aes_decrypt_key()
is a used to calculate the reverse round key for decryption, for this
operation the key has to be divided into 4 bytes, so to extract 4 bytes
from an u8 byte stream and store it in an u32 variable, get_aligned_be32()
is used. Similarly for copying back the key from u32 variable to the
original u8 key stream, put_aligned_be32() is used.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
<linux/cryptohash.h> sounds very generic and important, like it's the
header to include if you're doing cryptographic hashing in the kernel.
But actually it only includes the library implementation of the SHA-1
compression function (not even the full SHA-1). This should basically
never be used anymore; SHA-1 is no longer considered secure, and there
are much better ways to do cryptographic hashing in the kernel.
Most files that include this header don't actually need it. So in
preparation for removing it, remove all these unneeded includes of it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This reverts commit 27c6feb0fb33a665a746346e76714826a5be5d10.
For ipsec offload the chelsio's ethernet driver expects a single mtu
sized packet.
But when ipsec traffic is running using iperf, most of the packets in
that traffic are gso packets(large sized skbs) because GSO is enabled by
default in TCP, due to this commit 0a6b2a1dc2a2 ("tcp: switch to GSO
being always on"), so chcr_ipsec_offload_ok() receives a gso
skb(with gso_size non zero).
Due to the check in chcr_ipsec_offload_ok(), this function returns false
for most of the packet, then ipsec offload is skipped and the skb goes
out taking the coprocessor path which reduces the bandwidth for inline
ipsec.
If this check is removed then for most of the packets(large sized skbs)
the chcr_ipsec_offload_ok() returns true and then as GSO is on, the
segmentation of the packet happens in the kernel and then finally the
driver_xmit is called, which receives a segmented mtu sized packet which
is what the driver expects for ipsec offload. So this case becomes
unnecessary here, therefore removing it.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The locks are taken in this order during driver registration
(uld_mutex), at: cxgb4_register_uld.part.14+0x49/0xd60 [cxgb4]
(rtnl_mutex), at: rtnetlink_rcv_msg+0x2db/0x400
(uld_mutex), at: cxgb_up+0x3a/0x7b0 [cxgb4]
(rtnl_mutex), at: chcr_add_xfrmops+0x83/0xa0 [chcr](stucked here)
To avoid this now the netdev features are updated after the
cxgb4_register_uld function is completed.
Fixes: 6dad4e8ab3ec6 ("chcr: Add support for Inline IPSec").
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FW_ETH_TX_EO_WR used for sending UDP Segmentation Offload (USO)
requests expects the headers to be part of the descriptor and the
payload to be part of the SGL containing the DMA mapped addresses.
Hence, the DMA address in the first entry of the SGL can start after
the packet headers. Currently, unmap_sgl() tries to unmap from this
wrong offset, instead of the originally mapped DMA address.
So, use existing unmap_skb() instead, which takes originally saved DMA
addresses as input. Update all necessary Tx paths to save the original
DMA addresses, so that unmap_skb() can unmap them properly.
v2:
- No change.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Replace a couple of occurrences where the "aes-generic" cipher is
instantiated explicitly and only used for encryption of a single block.
Use AES library calls instead.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Do not request FW to generate cidx update if there is less
space in tx queue to post new request.
SGE DBP 1 pidx increment too large
BUG: unable to handle kernel NULL pointer dereference at
0000000000000124
SGE error for queue 101
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fixed Traffic Stall caused by
- Subcommands except last should have more bit set
- For esn case subcommand is required for linear skb only
- Also Optimized is_eth_imm usage
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Inline single pdu else take co-pro path
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
use is_eth_imm to determine immediate data than use sa_entry
field which is common for tunnel and not per skb.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Add 1472-byte test to tcrypt for IPsec
- Reintroduced crypto stats interface with numerous changes
- Support incremental algorithm dumps
Algorithms:
- Add xchacha12/20
- Add nhpoly1305
- Add adiantum
- Add streebog hash
- Mark cts(cbc(aes)) as FIPS allowed
Drivers:
- Improve performance of arm64/chacha20
- Improve performance of x86/chacha20
- Add NEON-accelerated nhpoly1305
- Add SSE2 accelerated nhpoly1305
- Add AVX2 accelerated nhpoly1305
- Add support for 192/256-bit keys in gcmaes AVX
- Add SG support in gcmaes AVX
- ESN for inline IPsec tx in chcr
- Add support for CryptoCell 703 in ccree
- Add support for CryptoCell 713 in ccree
- Add SM4 support in ccree
- Add SM3 support in ccree
- Add support for chacha20 in caam/qi2
- Add support for chacha20 + poly1305 in caam/jr
- Add support for chacha20 + poly1305 in caam/qi2
- Add AEAD cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (130 commits)
crypto: skcipher - remove remnants of internal IV generators
crypto: cavium/nitrox - Fix build with !CONFIG_DEBUG_FS
crypto: salsa20-generic - don't unnecessarily use atomic walk
crypto: skcipher - add might_sleep() to skcipher_walk_virt()
crypto: x86/chacha - avoid sleeping under kernel_fpu_begin()
crypto: cavium/nitrox - Added AEAD cipher support
crypto: mxc-scc - fix build warnings on ARM64
crypto: api - document missing stats member
crypto: user - remove unused dump functions
crypto: chelsio - Fix wrong error counter increments
crypto: chelsio - Reset counters on cxgb4 Detach
crypto: chelsio - Handle PCI shutdown event
crypto: chelsio - cleanup:send addr as value in function argument
crypto: chelsio - Use same value for both channel in single WR
crypto: chelsio - Swap location of AAD and IV sent in WR
crypto: chelsio - remove set but not used variable 'kctx_len'
crypto: ux500 - Use proper enum in hash_set_dma_transfer
crypto: ux500 - Use proper enum in cryp_set_dma_transfer
crypto: aesni - Add scatter/gather avx stubs, and use them in C
crypto: aesni - Introduce partial block macro
..
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/crypto/chelsio/chcr_ipsec.c: In function 'chcr_ipsec_xmit':
drivers/crypto/chelsio/chcr_ipsec.c:674:33: warning:
variable 'kctx_len' set but not used [-Wunused-but-set-variable]
unsigned int flits = 0, ndesc, kctx_len;
It not used since commit 8362ea16f69f ("crypto: chcr - ESN for Inline IPSec Tx")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
reduce noise when skb->sp is removed later in the series.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Send SPI, 64b seq nos and 64b IV with aadiv drop for inline crypto.
This information is added in outgoing packet after the CPL TX PKT XT
and removed by hardware.
The aad, auth and cipher offsets are then adjusted for ESN enabled tunnel.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Immediate packets sent to hardware should include the work
request length in calculating the flits. WR occupy one flit and
if not accounted result in invalid request which stalls the HW
queue.
Cc: stable@vger.kernel.org
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
-Tx request and data is copied to HW Q in 64B desc, check for
end of queue and adjust the current position to start from
beginning before passing the additional request info.
-key context copy should check key length only
-Few reverse christmas tree correction
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The Inline IPSec driver does not offload csum.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
fix a type cast error for queue descriptor
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In the case where skb->ip_summed != CHECKSUM_PARTIAL then cntrl contains
garbage value and this is possibly being bit-wise or'd and stored into
cpl->ctrl1. Fix this by initializing cntrl to zero.
Cleans up clang warning:
drivers/crypto/chelsio/chcr_ipsec.c:374:9: warning: The left expression
of the compound assignment is an uninitialized value. The computed value
will also be garbage
Fixes: 6dad4e8ab3ec ("chcr: Add support for Inline IPSec")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Variables adap, pi and cntrl are assigned but are never read, hence
they are redundant and can be removed.
Cleans up various clang build warnings.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
register xfrmdev_ops callbacks, Send IPsec tunneled data
to HW for inline processing.
The driver use hardware crypto accelerator to encrypt and
generate ICV for the transmitted packet in Inline mode.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Harsh Jain <harsh@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
