Age | Commit message (Collapse) | Author | Files | Lines |
|
[Why]
Some of the panels does not have the refresh rate range info
in base EDID and only have the refresh rate range info in
DisplayID block.
It will cause the max/min freesync refresh rate set to 0.
[How]
Try to parse the refresh rate range info from DisplayID if the
max/min refresh rate is 0.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We only enable the VRR while monitor usable refresh rate range
is greater than 10 Hz.
But we did not check the range in DRM_EDID_FEATURE_CONTINUOUS_FREQ
case.
[How]
Add a refresh rate range check before set the freesync_capable flag
in DRM_EDID_FEATURE_CONTINUOUS_FREQ case.
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Sometimes the new_crtc_state->vrr_infopacket did not sync up with the
current state.
It will affect the update_freesync_state_on_stream() does not update
the state correctly.
[How]
Reset the freesync config before get_freesync_config_for_crtc() to
make sure we have the correct new_crtc_state for VRR.
Reviewed-by: Sun peng Li <sunpeng.li@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We can't read/write to DCN registers while in IPS. Since, that can cause
the system to hang. So, before proceeding with the access in that
scenario, force the system out of IPS.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Disable idle optimization for each atomic commit is unnecessary,
and can lead to a potential race condition.
[How]
Remove idle optimization check from amdgpu_dm_atomic_commit_tail()
Fixes: 196107eb1e15 ("drm/amd/display: Add IPS checks before dcn register access")
Cc: stable@vger.kernel.org
Reviewed-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-6.10-2024-05-30:
amdgpu:
- RAS fix
- Fix colorspace property for MST connectors
- Fix for PCIe DPM
- Silence UBSAN warning
- GPUVM robustness fix
- Partition fix
- Drop deprecated I2C_CLASS_SPD
amdkfd:
- Revert unused changes for certain 11.0.3 devices
- Simplify APU VRAM handling
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240530202316.2246826-1-alexander.deucher@amd.com
|
|
Pull drm fixes from Dave Airlie:
"Some fixes for the end of the merge window, mostly amdgpu and panthor,
with one nouveau uAPI change that fixes a bad decision we made a few
months back.
nouveau:
- fix bo metadata uAPI for vm bind
panthor:
- Fixes for panthor's heap logical block.
- Reset on unrecoverable fault
- Fix VM references.
- Reset fix.
xlnx:
- xlnx compile and doc fixes.
amdgpu:
- Handle vbios table integrated info v2.3
amdkfd:
- Handle duplicate BOs in reserve_bo_and_cond_vms
- Handle memory limitations on small APUs
dp/mst:
- MST null deref fix.
bridge:
- Don't let next bridge create connector in adv7511 to make probe
work"
* tag 'drm-next-2024-05-25' of https://gitlab.freedesktop.org/drm/kernel:
drm/amdgpu/atomfirmware: add intergrated info v2.3 table
drm/mst: Fix NULL pointer dereference at drm_dp_add_payload_part2
drm/amdkfd: Let VRAM allocations go to GTT domain on small APUs
drm/amdkfd: handle duplicate BOs in reserve_bo_and_cond_vms
drm/bridge: adv7511: Attach next bridge without creating connector
drm/buddy: Fix the warn on's during force merge
drm/nouveau: use tile_mode and pte_kind for VM_BIND bo allocations
drm/panthor: Call panthor_sched_post_reset() even if the reset failed
drm/panthor: Reset the FW VM to NULL on unplug
drm/panthor: Keep a ref to the VM at the panthor_kernel_bo level
drm/panthor: Force an immediate reset on unrecoverable faults
drm/panthor: Document drm_panthor_tiler_heap_destroy::handle validity constraints
drm/panthor: Fix an off-by-one in the heap context retrieval logic
drm/panthor: Relax the constraints on the tiler chunk size
drm/panthor: Make sure the tiler initial/max chunks are consistent
drm/panthor: Fix tiler OOM handling to allow incremental rendering
drm: xlnx: zynqmp_dpsub: Fix compilation error
drm: xlnx: zynqmp_dpsub: Fix few function comments
|
|
MST colorspace property support was disabled due to a series of warnings
that came up when the device was plugged in since the properties weren't
made at device creation. Create the properties in advance instead.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 69a959610229 ("drm/amd/display: Temporary Disable MST DP Colorspace Property").
Reported-and-tested-by: Tyler Schneider <tyler.schneider@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3353
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing cleanup from Steven Rostedt:
"Remove second argument of __assign_str()
The __assign_str() macro logic of the TRACE_EVENT() macro was
optimized so that it no longer needs the second argument. The
__assign_str() is always matched with __string() field that takes a
field name and the source for that field:
__string(field, source)
The TRACE_EVENT() macro logic will save off the source value and then
use that value to copy into the ring buffer via the __assign_str().
Before commit c1fa617caeb0 ("tracing: Rework __assign_str() and
__string() to not duplicate getting the string"), the __assign_str()
needed the second argument which would perform the same logic as the
__string() source parameter did. Not only would this add overhead, but
it was error prone as if the __assign_str() source produced something
different, it may not have allocated enough for the string in the ring
buffer (as the __string() source was used to determine how much to
allocate)
Now that the __assign_str() just uses the same string that was used in
__string() it no longer needs the source parameter. It can now be
removed"
* tag 'trace-assign-str-v6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing/treewide: Remove second parameter of __assign_str()
|
|
With the rework of how the __string() handles dynamic strings where it
saves off the source string in field in the helper structure[1], the
assignment of that value to the trace event field is stored in the helper
value and does not need to be passed in again.
This means that with:
__string(field, mystring)
Which use to be assigned with __assign_str(field, mystring), no longer
needs the second parameter and it is unused. With this, __assign_str()
will now only get a single parameter.
There's over 700 users of __assign_str() and because coccinelle does not
handle the TRACE_EVENT() macro I ended up using the following sed script:
git grep -l __assign_str | while read a ; do
sed -e 's/\(__assign_str([^,]*[^ ,]\) *,[^;]*/\1)/' $a > /tmp/test-file;
mv /tmp/test-file $a;
done
I then searched for __assign_str() that did not end with ';' as those
were multi line assignments that the sed script above would fail to catch.
Note, the same updates will need to be done for:
__assign_str_len()
__assign_rel_str()
__assign_rel_str_len()
I tested this with both an allmodconfig and an allyesconfig (build only for both).
[1] https://lore.kernel.org/linux-trace-kernel/20240222211442.634192653@goodmis.org/
Link: https://lore.kernel.org/linux-trace-kernel/20240516133454.681ba6a0@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Christian König <christian.koenig@amd.com> for the amdgpu parts.
Acked-by: Thomas Hellström <thomas.hellstrom@linux.intel.com> #for
Acked-by: Rafael J. Wysocki <rafael@kernel.org> # for thermal
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Darrick J. Wong <djwong@kernel.org> # xfs
Tested-by: Guenter Roeck <linux@roeck-us.net>
|
|
[Why]
Commit:
- commit 5aa1dfcdf0a4 ("drm/mst: Refactor the flow for payload allocation/removement")
accidently overwrite the commit
- commit 54d217406afe ("drm: use mgr->dev in drm_dbg_kms in drm_dp_add_payload_part2")
which cause regression.
[How]
Recover the original NULL fix and remove the unnecessary input parameter 'state' for
drm_dp_add_payload_part2().
Fixes: 5aa1dfcdf0a4 ("drm/mst: Refactor the flow for payload allocation/removement")
Reported-by: Leon Weiß <leon.weiss@ruhr-uni-bochum.de>
Link: https://lore.kernel.org/r/38c253ea42072cc825dc969ac4e6b9b600371cc8.camel@ruhr-uni-bochum.de/
Cc: lyude@redhat.com
Cc: imre.deak@intel.com
Cc: stable@vger.kernel.org
Cc: regressions@lists.linux.dev
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240307062957.2323620-1-Wayne.Lin@amd.com
(cherry picked from commit 4545614c1d8da603e57b60dd66224d81b6ffc305)
|
|
Now that all previously-supported architectures select
ARCH_HAS_KERNEL_FPU_SUPPORT, this code can depend on that symbol instead
of the existing list of architectures. It can also take advantage of the
common kernel-mode FPU API and method of adjusting CFLAGS.
Link: https://lkml.kernel.org/r/20240329072441.591471-14-samuel.holland@sifive.com
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: WANG Xuerui <git@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The compiler flags enable altivec, but that is not required; hard-float is
sufficient for the code to build and function.
Drop altivec from the compiler flags and adjust the enable/disable code to
only enable FPU use.
Link: https://lkml.kernel.org/r/20240329072441.591471-13-samuel.holland@sifive.com
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Borislav Petkov (AMD) <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: Nathan Chancellor <nathan@kernel.org>
Cc: Nicolas Schier <nicolas@fjasle.eu>
Cc: Palmer Dabbelt <palmer@rivosinc.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: WANG Xuerui <git@xen0n.name>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Pull drm updates from Dave Airlie:
"This is the main pull request for the drm subsystems for 6.10.
In drivers the main thing is a new driver for ARM Mali firmware based
GPUs, otherwise there are a lot of changes to amdgpu/xe/i915/msm and
scattered changes to everything else.
In the core a bunch of headers and Kconfig was refactored, along with
the addition of a new panic handler which is meant to provide a user
friendly message when a panic happens and graphical display is
enabled.
New drivers:
- panthor: ARM Mali/Immortalis CSF-based GPU driver
Core:
- add a CONFIG_DRM_WERROR option
- make more headers self-contained
- grab resv lock in pin/unpin
- fix vmap resv locking
- EDID/eDP panel matching
- Kconfig cleanups
- DT sound bindings
- Add SIZE_HINTS property for cursor planes
- Add struct drm_edid_product_id and helpers.
- Use drm device based logging in more drm functions.
- drop seq_file.h from a bunch of places
- use drm_edid driver conversions
dp:
- DP Tunnel documentation
- MST read sideband cap
- Adaptive sync SDP prep work
ttm:
- improve placement for TTM BOs in idle/busy handling
panic:
- Fixes for drm-panic, and option to test it.
- Add drm panic to simpledrm, mgag200, imx, ast
bridge:
- improve init ordering
- adv7511: allow GPIO pin sharing
- tc358775: add tc358675 support
panel:
- AUO B120XAN01.0
- Samsung s6e3fa7
- BOE NT116WHM-N44
- CMN N116BCA-EA1,
- CrystalClear CMT430B19N00
- Startek KD050HDFIA020-C020A
- powertip PH128800T006-ZHC01
- Innolux G121X1-L03
- LG sw43408
- Khadas TS050 V2
- EDO RM69380 OLED
- CSOT MNB601LS1-1
amdgpu:
- HDCP/ODM/RAS fixes
- Devcoredump improvements
- Expose VCN activity via sysfs
- SMY 13.0.x updates
- Enable fast updates on DCN 3.1.4
- Add dclk and vclk reporting on additional devices
- Add ACA RAS infrastructure
- Implement TLB flush fence
- EEPROM handling fixes
- SMUIO 14.0.2 support
- SMU 14.0.1 Updates
- SMU 14.0.2 support
- Sync page table freeing with TLB flushes
- DML2 refactor
- DC debug improvements
- DCN 3.5.x Updates
- GPU reset fixes
- HDP fix for second GFX pipe on GC 10.x
- Enable secondary GFX pipe on GC 10.3
- Refactor and clean up BACO/BOCO/BAMACO handling
- Remove invalid TTM resource start check
- UAF fix in VA IOCTL
- GPUVM page fault redirection to secondary IH rings for IH 6.x
- Initial support for mapping kernel queues via MES
- Fix VRAM memory accounting
amdkfd:
- MQD handling cleanup
- Preemption handling fixes for XCDs
- TLB flush fix for GC 9.4.2
- Properly clean up workqueue during module unload
- Fix memory leak process create failure
- Range check CP bad op exception targets to avoid reporting invalid exceptions to userspace
- Fix eviction fence handling
- Fix leak in GPU memory allocation failure case
- DMABuf import handling fix
- Enable SQ watchpoint for gfx10
i915:
- Adding new DG2 PCI ID
- add context hints for GT frequency
- enable only one CCS for compute workloads
- new workarounds
- Fix UAF on destroy against retire race and remove two earlier partial fixes
- Limit the reserved VM space to only the platforms that need it
- Fix gt reset with GuC submission is disable
- Add and use gt_to_guc() wrapper
i915/xe display:
- Lunar Lake display enabling, including cdclk and other refactors
- BIOS/VBT/opregion related refactor
- Digital port related refactor/clean-up
- Fix 2s boot time regression on DP panel replay init
- Remove duplication on audio enable/disable on SDVO and g4x+ DP
- Disable AuxCCS framebuffers if built for Xe
- Make crtc disable more atomic
- Increase DP idle pattern wait timeout to 2ms
- Start using container_of_const() for some extra const safety
- Fix Jasper Lake boot freeze
- Enable MST mode for 128b/132b single-stream sideband
- Enable Adaptive Sync SDP Support for DP
- Fix MTL supported DP rates - removal of UHBR13.5
- PLL refactoring
- Limit eDP MSO pipe only for display version 20
- More display refactor towards independence from i915 dev_priv
- Convert i915/xe fbdev to DRM client
- More initial work to make display code more independent from i915
xe:
- improved error capture
- clean up some uAPI leftovers
- devcoredump update
- Add BMG mocs table
- Handle GSCCS ER interrupt
- Implement xe2- and GuC workarounds
- struct xe_device cleanup
- Hwmon updates
- Add LRC parsing for more GPU instruction
- Increase VM_BIND number of per-ioctl Ops
- drm/xe: Add XE_BO_GGTT_INVALIDATE flag
- Initial development for SR-IOV support
- Add new PCI IDs to DG2 platform
- Move userptr over to start using hmm_range_fault
msm:
- Switched to generating register header files during build process
instead of shipping pre-generated headers
- Merged DPU and MDP4 format databases.
- DP:
- Stop using compat string to distinguish DP and eDP cases
- Added support for X Elite platform (X1E80100)
- Reworked DP aux/audio support
- Added SM6350 DP to the bindings
- GPU:
- a7xx perfcntr reg fixes
- MAINTAINERS updates
- a750 devcoredump support
radeon:
- Silence UBSAN warnings related to flexible arrays
nouveau:
- move some uAPI objects to uapi headers
omapdrm:
- console fix
ast:
- add i2c polling
qaic:
- add debugfs entries
exynos:
- fix platform_driver .owner
- drop cleanup code
mediatek:
- Use devm_platform_get_and_ioremap_resource() in mtk_hdmi_ddc_probe()
- Add GAMMA 12-bit LUT support for MT8188
- Rename mtk_drm_* to mtk_*
- Drop driver owner initialization
- Correct calculation formula of PHY Timing"
* tag 'drm-next-2024-05-15' of https://gitlab.freedesktop.org/drm/kernel: (1477 commits)
drm/xe/ads: Use flexible-array
drm/xe: Use ordered WQ for G2H handler
drm/msm/gen_header: allow skipping the validation
drm/msm/a6xx: Cleanup indexed regs const'ness
drm/msm: Add devcoredump support for a750
drm/msm: Adjust a7xx GBIF debugbus dumping
drm/msm: Update a6xx registers XML
drm/msm: Fix imported a750 snapshot header for upstream
drm/msm: Import a750 snapshot registers from kgsl
MAINTAINERS: Add Konrad Dybcio as a reviewer for the Adreno driver
MAINTAINERS: Add a separate entry for Qualcomm Adreno GPU drivers
drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails
drm/msm/adreno: fix CP cycles stat retrieval on a7xx
drm/msm/a7xx: allow writing to CP_BV counter selection registers
drm: zynqmp_dpsub: Always register bridge
Revert "drm/bridge: ti-sn65dsi83: Fix enable error path"
drm/fb_dma: Add checks in drm_fb_dma_get_scanout_buffer()
drm/fbdev-generic: Do not set physical framebuffer address
drm/panthor: Fix the FW reset logic
drm/panthor: Make sure we handle 'unknown group state' case properly
...
|
|
[Why]
Some older MST hubs do not report DPCD registers according to
specification.
[How]
This change re-applies commit c53655545141 ("drm/amd/display: dsc mst
re-compute pbn for changes on hub").
With an additional check for these older MST devices.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
This fixes a bug introduced by commit c53655545141 ("drm/amd/display: dsc
mst re-compute pbn for changes on hub").
The change caused light-up issues with a second display that required
DSC on some MST docks.
[How]
Use Virtual DPCD for DSC caps in MST case.
[Limitations]
This change only affects MST DSC devices that follow specifications
additional changes are required to check for old MST DSC devices such as
ones which do not check for Virtual DPCD registers.
Reviewed-by: Swapnil Patel <swapnil.patel@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Panel replay was enabled by default in commit 5950efe25ee0
("drm/amd/display: Enable Panel Replay for static screen use case"), but
it isn't working properly at least on some BOE and AUO panels. Instead
of being static the screen is solid black when active. As it's a new
feature that was just introduced that regressed VRR disable it for now
so that problem can be properly root caused.
Cc: Tom Chung <chiahsuan.chung@amd.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3344
Fixes: 5950efe25ee0 ("drm/amd/display: Enable Panel Replay for static screen use case")
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why] DSC debugfs, such as dp_dsc_clock_en_read,
use aconnector->dc_link to find pipe_ctx for display.
Displays connected to MST hub share the same dc_link.
DSC instance is from pipe_ctx. This causes incorrect
DSC instance for display connected to MST hub.
[How] Add aconnector->sink check to find pipe_ctx.
CC: stable@vger.kernel.org
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This fixes 11 UNINIT issues reported by Coverity.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add the protoype for print ip state to be used
to print the registers in devcoredump during
a gpu reset.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add the prototype to dump ip registers
for all ips of different asics and set
them to NULL for now. Based on the
requirement add a function pointer for
each of them.
Signed-off-by: Sunil Khatri <sunil.khatri@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise we can end up with a frame on unsuspend where color management
is not applied when userspace has not committed themselves.
Fixes re-applying color management on Steam Deck/Gamescope on S3 resume.
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Otherwise we can end up with a frame on unsuspend where color management
is not applied when userspace has not committed themselves.
Fixes re-applying color management on Steam Deck/Gamescope on S3 resume.
Signed-off-by: Joshua Ashton <joshua@froggi.es>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
IPS ono sequence ordering differs based on the ASIC.
[How]
Detect the ASIC ID revision and set the boot option accordingly. Feed
it through the DCN35 DMUB functions.
Reviewed-by: Sung joon Kim <sungjoon.kim@amd.com>
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The previous check for the is_vsc_sdp_colorimetry_supported flag
for MST sink signals did nothing. Simplify the code and use the
same check for MST and SST.
Cc: stable@vger.kernel.org
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In order for display colorimetry to work correctly on DP displays
we need to send the VSC SDP packet. We should only do so for
panels with DPCD revision greater or equal to 1.4 as older
receivers might have problems with it.
Cc: stable@vger.kernel.org
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Cc: Agustin Gutierrez <Agustin.Gutierrez@amd.com>
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
mode_config's max width x height is 4096x2160 and is higher than DWB's
max resolution 3840x2160 which is returned instead.
Cc: stable@vger.kernel.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
dynamic memory safety error detector (KASAN) catches and generates error
messages "BUG: KASAN: slab-out-of-bounds" as writeback connector does not
support certain features which are not initialized.
[HOW]
Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3199
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a new DCN veriosn 3.5.1 need to load
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The previous check for the is_vsc_sdp_colorimetry_supported flag
for MST sink signals did nothing. Simplify the code and use the
same check for MST and SST.
Cc: stable@vger.kernel.org
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In order for display colorimetry to work correctly on DP displays
we need to send the VSC SDP packet. We should only do so for
panels with DPCD revision greater or equal to 1.4 as older
receivers might have problems with it.
Cc: stable@vger.kernel.org
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Xaver Hugl <xaver.hugl@gmail.com>
Cc: Melissa Wen <mwen@igalia.com>
Cc: Agustin Gutierrez <Agustin.Gutierrez@amd.com>
Reviewed-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
mode_config's max width x height is 4096x2160 and is higher than DWB's
max resolution 3840x2160 which is returned instead.
Cc: stable@vger.kernel.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
We want to block IPS2 for static screen but allow it for power state
transitions.
[How]
Set DalDisableIPS=6 for DCN35 which allows:
1. RCG during static screen
2. RCG during LVP
3. IPS2 for display off / S0i3
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Future implementations will require a distinction between AC power and
DC power (wall power and battery power, respectively). To accomplish this,
adding a power mode parameter to certain dc interfaces, and adding a
separate DML2 instance for DC mode validation. Default behaviour unchanged.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
dynamic memory safety error detector (KASAN) catches and generates error
messages "BUG: KASAN: slab-out-of-bounds" as writeback connector does not
support certain features which are not initialized.
[HOW]
Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK.
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/3199
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why/How]
Some issues may require a trace of the previous SMU messages from DC to
understand the context and aid in debugging. Actual logging to be
implemented when needed.
Reviewed-by: Josip Pavic <josip.pavic@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why] Mst slot nums equals to pbn / pbn_div.
Today, pbn_div refers to dm_mst_get_pbn_divider ->
dc_link_bandwidth_kbps. In dp_link_bandwidth_kbps,
which includes effect of FEC overhead already. As
result, we should not include effect of FEC overhead
again while calculating pbn by kpbs_to_peak_pbn
(stream_kbps).
[How] Include FEC overhead within dp_link_bandwidth_kbps.
Remove FEC overhead from kbps_to_peak_pbn.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why] Mode pbn is not calculated correctly because timing pixel encoding is
not checked within convert_dc_color_depth_into_bpc.
[How] Get mode kbps from dc_bandwidth_in_kbps_from_timing, then calculate
pbn by kbps_to_peak_pbn.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Roman Li <roman.li@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There is a new DCN veriosn 3.5.1 need to load
Signed-off-by: Li Ma <li.ma@amd.com>
Reviewed-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need to re-enable idle power optimizations after entering PSR. Since,
we get kicked out of idle power optimizations before entering PSR
(entering PSR requires us to write to DCN registers, which isn't allowed
while we are in IPS).
Fixes: a9b1a4f684b3 ("drm/amd/display: Add more checks for exiting idle in DC")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
displays without PSR"
This causes flicker on a bunch of eDP panels. The info_packet code
also caused regressions on other OSes that we haven't' seen on Linux
yet, but that is likely due to the fact that we haven't had a chance
to test those environments on Linux.
We'll need to revisit this.
This reverts commit 202260f64519e591b5cd99626e441b6559f571a3.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3207
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3151
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
[Why&How]
Remove several plane and stream pointers from dc for code
refactoring.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We need to re-enable idle power optimizations after entering PSR. Since,
we get kicked out of idle power optimizations before entering PSR
(entering PSR requires us to write to DCN registers, which isn't allowed
while we are in IPS).
Fixes: a9b1a4f684b3 ("drm/amd/display: Add more checks for exiting idle in DC")
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
displays without PSR"
This causes flicker on a bunch of eDP panels. The info_packet code
also caused regressions on other OSes that we haven't' seen on Linux
yet, but that is likely due to the fact that we haven't had a chance
to test those environments on Linux.
We'll need to revisit this.
This reverts commit 202260f64519e591b5cd99626e441b6559f571a3.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3207
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3151
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Incorrect function name in function banner.
[HOW]
Correct name and brief description.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Some eDP panels' ext caps don't write initial values. The value of
dpcd_addr (0x317) can be random and the backlight control interface
will be incorrect.
[HOW]
Add new panel patches to remove sink ext caps.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 6.5.x
Cc: Tsung-hua Lin <tsung-hua.lin@amd.com>
Cc: Chris Chi <moukong.chi@amd.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ryan Lin <tsung-hua.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY & HOW]
Enable DML2 related debug config options in DM for testing purposes.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The monitor shipped with the Framework 16 supports VRR [1], but it's not
being advertised.
This is because the detailed timing block doesn't contain
`EDID_DETAIL_MONITOR_RANGE` which amdgpu looks for to find min and max
frequencies. This check however is superfluous for this case because
update_display_info() calls drm_get_monitor_range() to get these ranges
already.
So if the `DRM_EDID_FEATURE_CONTINUOUS_FREQ` EDID feature is found then
turn on freesync without extra checks.
v2: squash in fix from Harry
Closes: https://www.reddit.com/r/framework/comments/1b4y2i5/no_variable_refresh_rate_on_the_framework_16_on/
Closes: https://www.reddit.com/r/framework/comments/1b6vzcy/framework_16_variable_refresh_rate/
Closes: https://community.frame.work/t/resolved-no-vrr-freesync-with-amd-version/42338
Link: https://gist.github.com/superm1/e8fbacfa4d0f53150231d3a3e0a13faf
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.9-2024-03-08-1:
amdgpu:
- DCN 3.5.1 support
- Fixes for IOMMUv2 removal
- UAF fix
- Misc small fixes and cleanups
- SR-IOV fixes
- MCBP cleanup
- devcoredump update
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Misc fixes and cleanups
- GFX10.1 trap fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240308170741.3691166-1-alexander.deucher@amd.com
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-next
amd-drm-next-6.9-2024-03-01:
amdgpu:
- GC 11.5.1 updates
- Misc display cleanups
- NBIO 7.9 updates
- Backlight fixes
- DMUB fixes
- MPO fixes
- atomfirmware table updates
- SR-IOV fixes
- VCN 4.x updates
- use RMW accessors for pci config registers
- PSR fixes
- Suspend/resume fixes
- RAS fixes
- ABM fixes
- Misc code cleanups
- SI DPM fix
- Revert freesync video
amdkfd:
- Misc cleanups
- Error handling fixes
radeon:
- use RMW accessors for pci config registers
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240301204857.13960-1-alexander.deucher@amd.com
Signed-off-by: Dave Airlie <airlied@redhat.com>
|